PIP5601C
Service Bulletin/Repair Instructions
This PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.
Vehicle report
2004 BUICK RAINIER
Service bulletins
592 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIP5358D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIP4723J
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5099H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT3271P
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
General Communication
Service Campaign
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
24-NA-141
Service Bulletin/Repair Instructions
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
16-NA-383
Service Bulletin/Repair Instructions
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
18-NA-099
Service Bulletin/Repair Instructions
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
24-NA-098
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
09-00-89-008G
Service Bulletin/Repair Instructions
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
10-08-45-001H
Service Bulletin/Repair Instructions
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
06-06-01-019C
Service Bulletin/Repair Instructions
This bulletin advises the technician of possible location of an internal coolant leak from a specific cylinder head and location.
22-NA-074
Service Bulletin/Repair Instructions
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
02-08-42-001J
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
Service Bulletin/Repair Instructions
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIP5601B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
23-NA-219
Service Bulletin/Repair Instructions
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
03-00-91-001I
Service Bulletin/Repair Instructions
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
17-NA-170
Service Bulletin/Repair Instructions
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
10-00-89-006J
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIT5099G
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
07-08-49-020R
Service Bulletin/Repair Instructions
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
23-NA-153
Service Bulletin/Repair Instructions
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
18-NA-073
Service Bulletin/Repair Instructions
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
PIP5628G
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5358C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
19-NA-219
Service Bulletin/Repair Instructions
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
PIP5628F
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
22-NA-009
Service Bulletin/Repair Instructions
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
17-NA-073
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
01-08-42-001O
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIP5628E
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
09-00-89-008F
Service Bulletin/Repair Instructions
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIP5540J
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
21-NA-124
Service Bulletin/Repair Instructions
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
PIT3271N
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
22-NA-205
Service Bulletin/Repair Instructions
This service bulletin provides information on Module Harvesting.
PIT3033B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that the Cam gear alignment can be incorrect after replacing the HVAC mode actuator.
10-00-89-006I
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIC5453D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
22-NA-195
Service Bulletin/Repair Instructions
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
06-00-89-031H
Service Bulletin/Repair Instructions
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
22-NA-181
Service Bulletin/Repair Instructions
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
PIP5640A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
20-NA-065
Service Bulletin/Repair Instructions
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
PIT5099F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5358B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
12-00-89-003B
Service Bulletin/Repair Instructions
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).
PIT3271M
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT3271L
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP4723F
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
22NA009
Service Bulletin/Repair Instructions
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
000090002L
Service Bulletin/Repair Instructions
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
030091001H
Service Bulletin/Repair Instructions
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
PIT3099U
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
010842001N
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
21NA124
Service Bulletin/Repair Instructions
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
100089006H
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIP5358A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
18NA099
Service Bulletin/Repair Instructions
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
PIP5163E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5540G
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5725A
Service Bulletin/Repair Instructions
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
RFI20201207_599-
Service Bulletin/Repair Instructions
This SKU is a Climate Control Module. The customer communication requested return of unsold inventory to inspect for a software issue. If the software issue exists it can cause a fan in the climate control system to stay on even when the ignition is turned off. The fan staying on even though the ignition is off can drain the battery, making the vehicle unable to start.
PIT3271K
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5628C
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5226D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5099E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5453C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
PIP5628B
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
070849020Q
Service Bulletin/Repair Instructions
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
PIT3116B
Service Bulletin/Repair Instructions
This Preliminary information communicates information to Clean the throttle body if the engine stalls at idle when the A/C comes on.
PIP5725
Service Bulletin/Repair Instructions
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
19NA219
Service Bulletin/Repair Instructions
This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
PIT3099T
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP4723D
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5540F
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
16NA383
Service Bulletin/Repair Instructions
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
PIT4297A
Service Bulletin/Repair Instructions
This Preliminary information communicates diagnostic information for a front noise.
100089009D
Service Bulletin/Repair Instructions
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.
PIT3254B
Service Bulletin/Repair Instructions
This Preliminary information communicates information for setting up the SDM.
010842001M
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
PIT3271J
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
100089006G
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
PIP5540E
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5601A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
100089009C
Service Bulletin/Repair Instructions
This informational bulletin provides information on key code security and information on GM key code look up applications.
150844001J
Service Bulletin/Repair Instructions
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
PIT3099S
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIT4204A
Service Bulletin/Repair Instructions
This Preliminary information communicates the normal operation of the CJ2 automatic HVAC system
PIT3099R
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
100845001G
Service Bulletin/Repair Instructions
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
060847001O
Service Bulletin/Repair Instructions
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
PIP5640
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5226C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5669A
Service Bulletin/Repair Instructions
This Preliminary information communicates the need to contact SPAC until GM CCA has sufficient stock.
PIT5669
Service Bulletin/Repair Instructions
This Preliminary information communicates the need to contact SPAC until GM CCA has sufficient stock.
070849020P
Service Bulletin/Repair Instructions
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
100845001F
Service Bulletin/Repair Instructions
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".
PIP5540D
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5628
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
17NA170
Service Bulletin/Repair Instructions
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
010842001L
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
PIP5540B
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
060847001N
Service Bulletin/Repair Instructions
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
PIP4925B
Service Bulletin/Repair Instructions
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIT5353C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIT3880A
Service Bulletin/Repair Instructions
This Preliminary information communicates a change in software in the PDM to prevent "wandering mirrors".
PIT3528D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that when the radio is replaced the manufactures "enable counter" will need to be cleared for the LED lamp to come on.
PIT4205B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to install Remote Keyless Entry
PIP5601
Service Bulletin/Repair Instructions
This Preliminary information communicates
PIP4138R
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIT5099D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5163D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT5099C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT5399A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIP5338B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
060601010D
Service Bulletin/Repair Instructions
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.
PIP5226B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP4138Q
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIT3271H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5540A
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP3343F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
PIP5540
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
PIC3100F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIT5353B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
070849020M
Service Bulletin/Repair Instructions
IPC Odometer Programming Method Quick Reference Guide
150089004B
Service Bulletin/Repair Instructions
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
150089005A
Service Bulletin/Repair Instructions
Essential Tools that Include Consumable Parts (U.S. Only)
PIP4723C
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5389E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT3099Q
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
PIP5163C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5588D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIT3099P
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
15-08-44-001I
Service Bulletin/Repair Instructions
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
15-08-73-001A
Service Bulletin/Repair Instructions
This informational bulletin explains how to update the older Onstar module software to new software over GSA.
06-08-47-001M
Service Bulletin/Repair Instructions
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.
10-00-89-006F
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers how to submit a product information report.
PIT5389C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
07-07-30-010D
Service Bulletin/Repair Instructions
This informational bulletin provides explanation on how to take snapshot data with a Tech 2 and upload it to a computer and where to email the info to.
PIC4935F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
PIP4723B
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIC3278G
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4801H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIC5588C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIP5029H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.
PIP5338A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
03-08-46-004S
Service Bulletin/Repair Instructions
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
07-08-49-020L
Service Bulletin/Repair Instructions
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
PIP4138P
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIC5492E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
05-00-89-055F
Service Bulletin/Repair Instructions
This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill procedures.
PIT3099N
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIP5163B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT5389B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
09-00-89-008C
Service Bulletin/Repair Instructions
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
07-08-49-020K
Service Bulletin/Repair Instructions
This informational bulletin explains the programming method quick reference guide for the IPC Odometer.
PIC5491J
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
PIP5029G
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.
PI1394A
Service Bulletin/Repair Instructions
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
000601012F
Service Bulletin/Repair Instructions
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.
030604017I
Service Bulletin/Repair Instructions
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
PIP5094A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.
PIP3940C
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE PROPER USE OF THE LOWER TIMING GEAR TENSIONER HOLDING TOOL (EN48464). BEFORE USING THE TOOL, MAKE SURE THAT THE TOOL HANDLE AND THREADED ROD UNSCREW FROM THE WEDGE. IF THE TOOL HANDLE UNSCREWS FROM THE THREADED ROD, LEAVING THE THREADED ROD SCREWED INTO THE WEDGE APPLY THREAD LOCKER TO THE THREADS OF THE TOOL HANDLE AND SCREW IT ONTO THE THREADED ROD TO PREVENT IT FROM COMING OFF IN THE FUTURE. THIS SHOULD BE DONE BEFORE REPLACING THE CYLINDER HEAD BY FOLLOWING THE LATEST VERSION OF 06-06-01-017. THE PROCEDURE FOR INSTALLING THE WEDGE TOOL IN THE LATEST VERSION OF 06-06-01-017 ADVISES THAT THE WEDGE SHOULD BE LIGHTLY SEATED USING A COUPLE OF VERY LIGHT TAPS WITH A SMALL PLASTIC OR BRASS HAMMER. ALTHOUGH THESE SHOULD BE LIGHT TAPS, THEY SHOULD ALSO BE SOLID TAPS TO ENSURE THAT THE WEDGE IS SEATED PROPERLY.
PIT-5485-B
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIT5485B
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC5088F
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
PIC-4935-E
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC-5050-A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIC4935E
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC5050A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIT5389A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
PIT5485A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC6181
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
08-07-30-026C
Service Bulletin/Repair Instructions
This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary
PIP5232C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIT5484A
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.
PIT3046G
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an inaccurate fuel gauge. Technician should drive the vehicle to duplicate the concern. The fuel gauge will have a tendency to falsely indicate a lower fuel level than what is actually present. The fuel gauge will take a few minutes to show the correct fuel level. On vehicles equipped with an automatic transmission no buffering takes place when the transmission is in park or neutral. This is a normal characteristic and no repairs are necessary. On vehicles equipped with a manual transmission the fuel gauge is buffered in all gears and neutral. There is a timer which starts to count up when the clutch is depressed. When this timer reaches its calibrated value the buffering stops. This is a normal characteristic and no repairs are necessary.
PIC5953A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
02-08-42-001I
Service Bulletin/Repair Instructions
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not
11-00-89-005I
Service Bulletin/Repair Instructions
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only)
PIP5226A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.
01-08-42-001K
Service Bulletin/Repair Instructions
This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
PIT4720D
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT AFTER REPLACING THE INSTRUMENT PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS UNKNOWN. DEALER WILL NEED TO FOLLOW DEALER TO THE GENERAL MOTORS SERVICE POLICIES AND PROCEDURES MANUAL SECTION 5.2.4 ODOMETER SERVICING.
16-NA-025
Service Bulletin/Repair Instructions
This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks
03-08-46-004R
Service Bulletin/Repair Instructions
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)
GCUS-9-1522
Service Bulletin/Repair Instructions
14423C - SPECIAL COVERAGE (REVISED SERVICE PROCEDURE). A FUEL TANK INLET CHECK VALVE (ICV) COULD FRACTURE. THE ICV IS LOCATED ABOVE THE FULL FUEL LEVEL. A FRACTURED ICV COULD ALLOW FUEL VAPORS TO PASS THROUGH AND DROPLETS OF FUEL TO ACCUMULATE ON THE SIDE OF THE FUEL TANK AS IT PASSES OVER THE FRACTURE DURING REFUELING. IF THE ICV FRACTURES, THE VEHICLES SERVICE ENGINE SOON (SES) LIGHT MAY ILLUMINATE, AND THE OWNER MAY NOTICE A FUEL ODOR AND/OR A FEW DROPS OF FUEL ON THE GROUND WHEN REFUELING THE VEHICLE. IF THE CONDITION OCCURS WITHIN THE STATED TERMS, THE FUEL TANK WILL BE REPLACED.
06-06-01-010C
Service Bulletin/Repair Instructions
This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period.
GCUS-9-1493
Service Bulletin/Repair Instructions
14423B - SPECIAL COVERAGE (REVISED PART INFORMATION AND SERVICE PROCEDURE). A FUEL TANK INLET CHECK VALVE (ICV) COULD FRACTURE. THE ICV IS LOCATED ABOVE THE FULL FUEL LEVEL. A FRACTURED ICV COULD ALLOW FUEL VAPORS TO PASS THROUGH AND DROPLETS OF FUEL TO ACCUMULATE ON THE SIDE OF THE FUEL TANK AS IT PASSES OVER THE FRACTURE DURING REFUELING. IF THE ICV FRACTURES, THE VEHICLES SERVICE ENGINE SOON (SES) LIGHT MAY ILLUMINATE, AND THE OWNER MAY NOTICE A FUEL ODOR AND/OR A FEW DROPS OF FUEL ON THE GROUND WHEN REFUELING THE VEHICLE. IF THE CONDITION OCCURS WITHIN THE STATED TERMS, THE FUEL TANK WILL BE REPLACED.
14423B
Service Bulletin/Repair Instructions
Special Coverage Adjustment ? Fuel Tank Inlet Check Valve Fracture
PIC6140B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.
PIT5353A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIT5484
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.
PIT5486
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that when dialing certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar Canada Upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
14423A
Service Bulletin/Repair Instructions
14423A - SPECIAL COVERAGE (REVISED PART INFORMATION). SOME 2004 MODEL YEAR BUICK RAINIER, 2003-2004 MODEL YEAR CHEVROLET SSR, 2002-2004 MODEL YEAR CHEVROLET TRAILBLAZER, CHEVROLET TRAILBLAZER EXT, GMC ENVOY, GMC ENVOY XL, AND OLDSMOBILE BRAVADA, AND 2004 MODEL YEAR GMC ENVOY XUV VEHICLES CONTAIN A FUEL TANK INLET CHECK VALVE (ICV) THAT COULD FRACTURE. THE ICV IS LOCATED ABOVE THE FULL FUEL LEVEL. A FRACTURED ICV COULD ALLOW FUEL VAPORS TO PASS THROUGH AND DROPLETS OF FUEL TO ACCUMULATE ON THE SIDE OF THE FUEL TANK AS IT PASSES OVER THE FRACTURE DURING REFUELING. IF THE ICV FRACTURES, THE VEHICLES SERVICE ENGINE SOON (SES) LIGHT MAY ILLUMINATE, AND THE OWNER MAY NOTICE A FUEL ODOR AND/OR A FEW DROPS OF FUEL ON THE GROUND WHEN REFUELING THE VEHICLE. DEALERS ARE TO REPLACE THE FUEL TANK.
PIT4943D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
06-00-89-031D
Service Bulletin/Repair Instructions
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
07-08-49-020J
Service Bulletin/Repair Instructions
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
15-NA-079
Service Bulletin/Repair Instructions
OnStar® Voice Fallback Number Update Some customers may have received a letter from OnStar® stating that "We recently tried to provide a software update to the OnStar® hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar® system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar® module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."
PIP5232B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIT5480
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that intermittently the cruise control is inoperative or that it will not set around or over 70 mph. Technician will need to insure that all four tires are the same size, brand and have similar wear. Verify the Power Control Module and Electronic Brake Control Module tire calibrations are correct. Technician will now check the Instrument Panel Cluster, Power Control Module and Electronic Brake Control Module data for the wheel speeds at 70 MPH or above and write down the difference for each set of speed data. Technician will need to use a Global Positioning System to determine actual speed and compare it to the Power Control Module and Electronic Brake Control Module readings. If the Global Positioning System and Power Control Module speeds match, suspect front wheel hubs and they should be replaced.
PIC3100E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
15-08-44-001F
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
15-08-44-001G
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
PIC6140A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.
14423
Service Bulletin/Repair Instructions
14423 - SPECIAL COVERAGE. SOME VEHICLES CONTAIN A FUEL TANK INLET CHECK VALVE (ICV) THAT COULD FRACTURE. THE ICV IS LOCATED ABOVE THE FULL FUEL LEVEL. A FRACTURED ICV COULD ALLOW FUEL VAPORS TO PASS THROUGH AND DROPLETS OF FUEL TO ACCUMULATE ON THE SIDE OF THE FUEL TANK AS IT PASSES OVER THE FRACTURE DURING REFUELING. IF THE ICV FRACTURES, THE VEHICLES SERVICE ENGINE SOON (SES) LIGHT MAY ILLUMINATE, AND THE OWNER MAY NOTICE A FUEL ODOR AND/OR A FEW DROPS OF FUEL ON THE GROUND WHEN REFUELING THE VEHICLE. DEALERS ARE TO REPLACE THE FUEL TANK.
PIC5953B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5338
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
PIP4404F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.
PIT5464
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP5325
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
09-09-40-001C
Service Bulletin/Repair Instructions
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
PIC6107
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
15-08-44-001C
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PIC6101
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are unable to receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Technician will need to push the OnStar Blue button and verify the system successfully connects to an advisor. Place an outbound personal call from the vehicle and verify it connects. Place an inbound call to the vehicle making sure to dial using the 11 digit phone number (1 + area code + number). If outbound calls can be placed and only incoming calls fail. Cycle power to the Vehicle Communication Interface Module and retest inbound call to the vehicle. If the power cycle corrects the concern and the module manufacturer is continental, replace the Vehicle Communication Interface Module. If the power cycle corrects the concern and the module manufacturer is LG, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance. If the concern is still present after the power cycle, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance.
PIT5384A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
02-07-30-052J
Service Bulletin/Repair Instructions
This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow®.
05-06-04-035E
Service Bulletin/Repair Instructions
This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles.
15-08-44-001A
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-44-001B
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
02-08-42-001H
Service Bulletin/Repair Instructions
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
PIT5399
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIC4310L
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIP4573B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have Service Engine Soon Malfunction Indicator Lamp on and a reduced engine power after cold starting their engine when the ambient temperature is approximately ? 10 Fahrenheit (-23 Celsius). Technician may find Diagnostic Trouble Codes P1516, P2101, P2119, and/or P2176. Technician may find some vehicles may have an oil leak from the front or rear crank seal, cam cover gasket, or dipstick tube as well. Technician will need to determine if the concern is the result of a frozen positive crankcase ventilation system. To determine if the concern is the result of a frozen positive crankcase ventilation system on inline 4 and 5 engines disconnect the positive crankcase ventilation vacuum pipe that is attached to the rear of cam cover and inspect the inside of it for ice, moisture, and/or sludge. Also inspect the engine oil dipstick and engine oil fill cap for moisture, sludge, and/or ice. To determine if the concern is the result of a frozen positive crankcase ventilation system on inline 6 carefully disconnect the top or the bottom of the rubber positive crankcase ventilation vacuum hose that is between the #3 and #4 intake runners and inspect for ice. Also inspect the engine oil dipstick and engine oil fill cap for moisture, sludge, and/or ice. If the positive crankcase ventilation is not determined to be frozen follow Service Information diagnosis and any other bulletins or Preliminary Information that apply to the vehicle you are working on. If there is moisture, ice, and/or sludge in/on the oil fill cap, oil dipstick, and/or positive crankcase ventilation vacuum tube, this is most likely the result of a frozen positive crankcase ventilation system and the suggestions in the Preliminary Information should be followed. Technician should clean any ice, sludge, water out of the positive crankcase ventilation pipes, hoses and throttle body, and allow them to dry. Te
05-08-46-006T
Service Bulletin/Repair Instructions
This informational bulletin provides information to dealership personnel on upgrading certain OnStar Analog/Digital-Ready Systems to OnStar Generation 6 Digital-Capable System.
PIP4581B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have an engine rattle that star after the engine was repaired ant the repair required the crankshaft balancer removal and replacement. When the rattle noise is duplicated without the Service Engine Soon Malfunction Indicator Lamp and Service Information diagnosis does not isolate the cause the crankshaft balancer bolt should be re-torqued per the specifications states in Service Information. When the rattle noise is duplicated with the Service Engine Soon Malfunction Indicator Lamp and Diagnostic Trouble Code P0016 or P0017 and Service Information diagnosis does not isolate the cause the crankshaft balancer bolt should be re-torqued per the specifications states in Service Information. If tightening the bolt repairs the rattle noise but the Diagnostic Trouble Code P0016 or P0017 continue to set technician should follow published Service Information diagnostics for the Diagnostic Trouble Code. If Service Information diagnostics for the Diagnostic Trouble Code do not lead to a repair for the Diagnostic Trouble Code remove the crankshaft timing sprocket and inspect the crankshaft alignment pin and the related groove of the sprocket for obvious wear. If wear is present replace the sprocket and pin and retest.
PIP4945B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0017 may be set current or history. Technician will need to follow published Service Information and all technical services bulletins for Diagnostic Trouble Code P0017. If Service Information diagnostics do not lead to a resolution to the concern there six other reasons Diagnostic Trouble Code P0017 can be set. First the tech should check the timing of the engine. Second issue may be a crank timing gear has a loose fit to the crank follow the current version of PIP3694. The third issue may be the crank end play is excessive see the current version of PIP3694. The forth issue is the cam actuator solenoid is restricted or screens are missing, see current version of PIP3694. The fifth concern may be a cam actuator is sticking, check the current version of PIP4913. And the sixth concern could be low oil pressure or oil contamination, refer to the current version of PIP4913.
15-08-44-001
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-73-001
Service Bulletin/Repair Instructions
This informational bulletin provides information on communication with OnStar® module after Canadian cellular upgrade.
PIT5264C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
05-00-89-055E
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information to clarify proper transaction administration of GM Dealer Empowerment Program and Goodwill Cases.
06-08-47-001K
Service Bulletin/Repair Instructions
This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty.
10-08-45-001E
Service Bulletin/Repair Instructions
This informational bulletin updates information on electrical ground repairs using new replacement fasteners with conductive finish.
PI1394
Service Bulletin/Repair Instructions
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.
PIT3271G
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIC3278F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4310K
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
03-00-91-001G
Service Bulletin/Repair Instructions
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
030848006J
Service Bulletin/Repair Instructions
This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.
1008110001C
Service Bulletin/Repair Instructions
This information provides the proper way to install the floor mats .
PIT5353
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP5029F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
PIT5264B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
11-00-89-005H
Service Bulletin/Repair Instructions
This warranty bulletin clarifies the use of dealer empowerment to satisfy the customer.
13-00-89-004J
Service Bulletin/Repair Instructions
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIT5099A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5232A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
07-08-49-020I
Service Bulletin/Repair Instructions
This informational bulletin provides a quick guide to updating which model vehicle after replacing the IPC.
PIT5264A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
PIC6036
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.
PIP5232
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP5226
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
10-08-110-001B
Service Bulletin/Repair Instructions
This informational bulletin provides information on how to use floor mats.
10-00-89-006E
Service Bulletin/Repair Instructions
This information bulletin provides the dealers on how to submit a product information report.
PIT3099M
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIC4310J
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
00-06-01-012E
Service Bulletin/Repair Instructions
This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.
PIP5163A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
00-00-89-027H
Service Bulletin/Repair Instructions
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.
10-00-89-006D
Service Bulletin/Repair Instructions
This information bulletin provides the dealers on how to submit a product information report.
Recalls
Service Bulletin/Repair Instructions
Vehicle Recalls
PIC5088E
Service Bulletin/Repair Instructions
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.
PIC5588B
Service Bulletin/Repair Instructions
Programming And Activation Of Replacement OnStar Modules.
05-08-46-006S
Service Bulletin/Repair Instructions
This informational bulletin advises the technician to update the Onstar from an analog system to a digital system if the customer wishes.
13-00-89-004I
Service Bulletin/Repair Instructions
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
05-06-04-035D
Service Bulletin/Repair Instructions
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
01-08-42-001J
Service Bulletin/Repair Instructions
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
02-08-42-001G
Service Bulletin/Repair Instructions
This informational bulletin is to assist with the identification of issues that are not considered warrantable.
PIT3099L
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
13-00-89-004H
Service Bulletin/Repair Instructions
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles.
PIP3343E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
PIP3343D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
13-00-89-004G
Service Bulletin/Repair Instructions
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIT5264
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
PIT4864F
Service Bulletin/Repair Instructions
Information On Requests To Add OnStar Bluetooth Option.
PIC3011H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
13-00-89-004F
Service Bulletin/Repair Instructions
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIT4943C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIC5453A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
99-08-51-007F
Service Bulletin/Repair Instructions
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
PIC5953
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP3140F
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PIP5169
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are setting Diagnostic Trouble Code P0300 after engine repairs. Technician will need to ensure that injector connectors for cylinder 5-7 and 6-8 are not crossed.
PI0281D
Service Bulletin/Repair Instructions
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
10-00-89-006C
Service Bulletin/Repair Instructions
This informational bulletin provides directions on submitting different PIRs
13-00-89-004E
Service Bulletin/Repair Instructions
This preliminary information bulletin provides a revision of 13-00-89-004D to include updated information.
05-00-89-072C
Service Bulletin/Repair Instructions
This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.
13-00-89-004D
Service Bulletin/Repair Instructions
This informational bulletin provides an update for 13-00-89-004C to include updated information.
04-06-04-047L
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 04-06-04-047K to add the 2014 model year.
05-06-04-022J
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 04-06-04-047 to add the 2014 model year.
10-08-110-001A
Service Bulletin/Repair Instructions
This informational Bulletin provides a revision for 10-08-110-001 to add the 2012-2014 model years.
PIP5163
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT3099K
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
130089009
Service Bulletin/Repair Instructions
Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules
PIC5904
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.
06-06-01-010B
Service Bulletin/Repair Instructions
This informational bulletin provides information on close-coupled converter and engine replacement.
PIP4404E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.
00-03-10-003R
Service Bulletin/Repair Instructions
This warranty administration bulletin provide policy information new tire warranty program and global warranty management submission information.
PIP4138N
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
10-00-89-010C
Service Bulletin/Repair Instructions
This informational bulletin provides information on key codes security rules and information on GM key code look up application.
10-00-89-009B
Service Bulletin/Repair Instructions
This informational bulletin provides information on key code security and information on GM key code look up applications.
07-08-49-020H
Service Bulletin/Repair Instructions
This technical service bulletin provides a revision for 07-08-49-020G to add the 2014 model year and update model list.
02-07-30-052I
Service Bulletin/Repair Instructions
This informational bulletin provides information for Automatic Transmission Oil Cooler Flow Test Essential Tool J-45096 TransFlow.
08-06-01-006D
Service Bulletin/Repair Instructions
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
11-00-89-005E
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.
02-08-98-002D
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.
09-00-89-008A
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.
05-08-48-001C
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor Operation.
13-00-89-004B
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 13-00-89-004A to include updated information.
PIT4720C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
13-00-89-005
Service Bulletin/Repair Instructions
This technical bulletin provides Warranty Administration - New Labor Codes information.
13-00-89-004A
Service Bulletin/Repair Instructions
This technical bulletin provides a revision of 13-00-89-004 to update car issues information for reference information/bulletin PI0746C.
99-04-20-002H
Service Bulletin/Repair Instructions
This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.
13-00-89-004
Service Bulletin/Repair Instructions
This technical bulletin provides a revision of 10-00-89-017Z to include updated information.
11-00-89-005D
Service Bulletin/Repair Instructions
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm.
10-00-89-017Z
Service Bulletin/Repair Instructions
This informational bulletin provides information on fix it right for first time issues.
00-03-10-002G
Service Bulletin/Repair Instructions
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
PIP3140E
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PIP5094
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
08-08-51-002A
Service Bulletin/Repair Instructions
This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.
PIP4138M
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIP4138L
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
11-00-89-005C
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm
PIC3718E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
PIT3173C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
PIT3271F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
10-00-89-017X
Service Bulletin/Repair Instructions
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.
080846004A
Service Bulletin/Repair Instructions
This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.
000089027G
Service Bulletin/Repair Instructions
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
PIC4310H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
100089010B
Service Bulletin/Repair Instructions
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
01-00-89-010J
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.
010089010J
Service Bulletin/Repair Instructions
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.
100089017W
Service Bulletin/Repair Instructions
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
PIT4907A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
10-08-64-002B
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork
PIC4935D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
PIP5072
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have slip in forward ranges immediately after replacing the input housing. Technician will inspect the 3-4 clutches and the forward clutch oil feed passages for leakage between circuits. Technician should apply regulated compressed air to the 3-4 clutch feed hole and the forward clutch feed hole one at a time with the input housing. Technician will need to replace the input housing if there is an air leak 3-4 clutches.
PIT3099J
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
11-00-89-005B
Service Bulletin/Repair Instructions
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm
10-00-89-017V
Service Bulletin/Repair Instructions
This informational bulletin provides information on newly release bulletins used to fi the vehicles in the field the first time.
PIC5588A
Service Bulletin/Repair Instructions
Programming And Activation Of Replacement OnStar Modules.
PIT-5141
Service Bulletin/Repair Instructions
BUICK/CADILLAC/CHEVROLET/GMC/OLDSMOBILE: IF BLOWER MOTOR IS SET TO ANY SPEED POSITION AND WHEN KEY IS OFF, IT BECOMES INOPERATIVE AND MAY STILL BE INOPERATIVE AFTER KEY IS TURNED ON. *PE UPDATED ON 5/1/12. *JS
09-09-40-001A
Service Bulletin/Repair Instructions
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE
PIP-4492P
Service Bulletin/Repair Instructions
BUICK/CADILLAC/CHEVROLET/GMC/HUMMER/PONTIAC/SAAB: OIL CONSUMPTION AND/OR EXHAUST SMOKE-POSSIBLE PCV BAFFLE OR LIFTER CONCERN. UPON INSPECTION, OBVIOUS OIL WILL BE FOUND IN THE INTAKE MANIFOLD AND/OR PCV VACUUM TUBE. *PE UPDATED 3/21/11. *PE UPDATED 5/9/11. *PE UPDATED 5/25/11. *PE UPDATED 06/16/2011. *KB UPDATED A SECOND TIME ON 06/16/2011. *KB UPDATED 6/27/11. *PE
PIP-4138K
Service Bulletin/Repair Instructions
GM: THE SERVICE ENGINE SOON LIGHT IS ON, THERE IS ALSO A MISFIRE OR ENGINE NOISE. THERE ARE MULTIPLE POSSIBLE CAUSES. *RM
SB-10-02-33-001
Service Bulletin/Repair Instructions
BUICK/CADILLAC/CHEVROLET/GMC/OLDSMOBILE AND HUMMER: INFORMATION ON PITMAN ARM SHAFT SEAL SERVICE KIT. DO NOT REPLACE ENTIRE STEERING GEAR FOR PITMAN SEAL LEAK. TECHNICIANS HAVE BEEN REPLACING ENTIRE STEERING GEARS DUE TO NOT BEING ABLE TO SERVICE JUST LEAKING PITMAN SHAFT SEAL. *PE UPDATED 5/9/11. *PE
SB-070417001D
Service Bulletin/Repair Instructions
GMC/BUICK/OLDSMOBILE/SAAB: BUMP OR THUMP NOISE IS HEARD COMING FROM THE REAR SUSPENSION OR FELT IN THE FLOOR. THE INFORMATION AFFECT VEHICLES WITH G67 AUTOMATIC LEVEL CONTROL REAR SUSPENSION. *PE UPDATED 3/30/11. *PE
08089-B
Service Bulletin/Repair Instructions
GENERAL MOTORS CORP: SPECIAL COVERAGE ADJUSTMENT; ANALOG ONSTAR DEACTIVATION. *PE UPDATED 2/17/09. *PE
07076
Service Bulletin/Repair Instructions
BUICK CHEVROLET GMC OLDSMOBILE SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT - FUEL TANK MODULAR RESERVOIR ASSEMBLY CORROSION. CSC LETTER WAS RECEIVED. UPDATED 11/6/08. *PE UPDATED 5/5/09. CSC LETTER WAS RECEIVED. *PE
PIT-4722
Service Bulletin/Repair Instructions
GMC: FLUID LEAK FROM TRANSMISSION OIL COOLER LINES DUE TO CORROSION. ALL 2000-2006 LIGHT DUTY TRUCKS EQUIPPED WITH THE LIGHT DUTY AUTOMATIC TRANSMISSION. *PE
08-089B
Service Bulletin/Repair Instructions
BUICK CHEVROLET GMC SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. CSC LETTER WAS RECEIVED. *PE
PIT-3046E
Service Bulletin/Repair Instructions
GMC: FUEL GAUGE FLUCTUATION IN PARK OR NEUTRAL, CAUSING THE LOW FUEL LIGHT TO ILLUMINATE. *PE
08-089
Service Bulletin/Repair Instructions
BUICK CADILLAC CHEVROLET GMC HUMMER OLDSMOBILE PONTIAC SAAB SATURN SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. FCC RULED IN 2002 WIRELESS CARRIERS WOULD NO LONGER RE REQUIRED TO SUPPORT ANALOG WIRELESS NETWORK STARTING IN 2008. *PE CSC LETTER WAS RECEIVED. UPDATED 12/1/08. *PE
05-03-08-007
Service Bulletin/Repair Instructions
RATTLE, CLUNK, POP, SNAP NOISE FROM FRONT AND/OR REAR SUSPENSION WHILE DRIVING OVER ROUGH, UNEVEN, WASH BOARD ROAD SURFACES. *TT (REPLACE APPROPRIATE STABILIZER LINK(S)). UPDATED 7/11/08. *NJ
PIP4054A
Service Bulletin/Repair Instructions
EATON LOCKING DIFFERENTIAL CHATTER SHUDDER NOISE ON TURNS, EQUIPPED WITH A LOCKING REAR DIFFERENTIAL RPO G80. *NJ UPDATED 7/17/2008. *PE
05-04-21-003
Service Bulletin/Repair Instructions
SERVICE 4WD LIGHT ILLUMINATED, DIAGNOSTIC TROUBLE CODE (DTC) C0374 SET. *TT UPDATED 10/05/07. *NJ INSPECT WIRING HARNESS TO TRANSFER CASE SPEED SENSORS, REPLACE WIRING HARNESS. UPDATED 7/18/08 *PE
3222
Service Bulletin/Repair Instructions
INTERMITTENT BOOM, RUMBLING NOISE AT HIGHWAY SPEED. *TT UPDATED 2/27/08. *NJ
3832
Service Bulletin/Repair Instructions
ABS, RED BRAKE ,SVC AND 4WD LIGHT ON HVAC BLOWER INOPERATIVE. *AK UPDATED 1/30/08. *NJ
4491
Service Bulletin/Repair Instructions
HEADLAMP FLICKER OR MOMENTARILY DIM WHILE DRIVING. 06-06-03-004 SUPPLEMENT. SHORT WHEEL BASE ONLY. *NJ UPDATED 1/30/08. *NJ
010866007
Service Bulletin/Repair Instructions
CENTER HIGH-MOUNT STOP LAMP (CHMSL) APPLIQUE LOOSE (RE-TAPE APPLIQUE) *TT UPDATED 11/02/07 *NJ
040232001
Service Bulletin/Repair Instructions
RELEASE OF STEERING GEAR STUB SHAFT BEARING KIT FOR SERVICE. *TT UPDATED 08-15-07. *KB UPDATED 10/09/07. *NJ
040525002
Service Bulletin/Repair Instructions
ABS LIGHT ON, DTC'S C0265, C0201, U1041 SET AND/OR LOSS OF COMMUNICATION WITH BRAKE MODULE. (REGROUND EBCM GROUND). *KB
030864006
Service Bulletin/Repair Instructions
DOORS HARD TO CLOSE. *TT UPDATED 07-24-07. *KB
060139002
Service Bulletin/Repair Instructions
FRONT BLOWER MOTOR INOPERATIVE OR MAY NOT SHUT OFF IN EXTREMELY LOW AMBIENT TEMPERATURE CONDITIONS. *KB
030417002
Service Bulletin/Repair Instructions
WHINE NOISE FROM REAR AXLE. *TT
3208
Service Bulletin/Repair Instructions
4WD INOPERATIVE AND OR ERRATIC FUEL GAUGE AND OR DIAGNOSTIC TROUBLE CODE'S. *EH
3154
Service Bulletin/Repair Instructions
MISFIRE, BUMP OR MULTIPLE BUMPS AFTER A 1-2 UPSHIFT. *TT
050602012
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON (SES) OR CHECK ENGINE LIGHT ON, DTC P0526, P0480, P1481, AND P1484 SET. *TT UPDATED. *KB
060604048
Service Bulletin/Repair Instructions
4.2L LL8 ENGINE FLASHING AND/OR MIL/SES LIGHT. ROUGH IDLE, MISFIRE. DTC P0300, P0301, P0302, P0303, P0304, P0305, AND P0306. *KB
030857004
Service Bulletin/Repair Instructions
WET FRONT FLOOR CARPET. *TT UPDATE. *TT UPDATE. *KB
040604090
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON (SES) LIGHT ON, DIAGNOSTIC TROUBLE CODE (DTC) P0483. *TT
040603005
Service Bulletin/Repair Instructions
PROPER CONNECTION INFORMATION TO AVOID BLOWN 125 AMP FUSE AND VARIOUS INTERIOR ELECTRICAL SYSTEM CONDITIONS WHEN JUMP STARTING VEHICLE. *TT
060602003
Service Bulletin/Repair Instructions
OPERATING CHARACTERISTICS OF THE ELECTRO-VISCOUS (EV) FAN CLUTCH AND DIAGNOSTIC TIPS FOR COOLING FAN NOISE, DELAYED TRANSMISSION SHIFTS AND/OR ENGINE REVVING TOO HIGH. *TT
060866001
Service Bulletin/Repair Instructions
REVISED LIFTGATE LOCK CYLINDER REPLACEMENT. *TT
030940006
Service Bulletin/Repair Instructions
INFORMATION ON AVOIDING FRONT SEAT BELT RETRACTOR JAMMING WHEN STORING SEAT BELT. *TT UPDATED *EH
040525002B
Service Bulletin/Repair Instructions
ANTI-LOCK BRAKE SYSTEM (ABS) LIGHT ON, DIAGNOSTIC TROUBLE CODES (DTCS) C0265, C0201, U1041 SET AND/OR LOSS OF COMMUNICATION WITH BRAKE MODULE. *TT UPDATE. *TT
050308014
Service Bulletin/Repair Instructions
REVISED STABILIZER SHAFT REPLACEMENT. *TT
050730031
Service Bulletin/Repair Instructions
4L60-E AUTOMATIC TRANSMISSION TORQUE CONVERTER CLUTCH (TCC) SHUDDER, WATER IN TRANSMISSION (REPAIR TRANSMISSION AND REPLACE TRANSMISSION FILLER TUBE, LEVEL INDICATOR AND SEAL). *AK
010730038B
Service Bulletin/Repair Instructions
THE SERVICE ENGINE SOON LAMP IS ILLUMINATED, NO 3RD AND 4TH GEAR, THE TRANSMISSION DOES NOT SHIFT CORRECTLY, THE TRANSMISSION FEELS LIKE IT SHIFTS TO NEUTRAL OR A LOSS OF DRIVE OCCURS. *TT
040843005B
Service Bulletin/Repair Instructions
WINDSHIELD WIPER MOTOR MODULE ASSEMBLIES. *MJ
050601026
Service Bulletin/Repair Instructions
INFORMATION ON USE OF BOLT EXTRACTOR TOOL KIT PART NUMBER EN-47702 FOR REMOVING BROKEN CYLINDER HEAD OR MAIN BEARING CAP BOLTS ON INLINE TRUCK ENGINES. *TT
050846006A
Service Bulletin/Repair Instructions
INFORMATION ON UPGRADING CERTAIN ONSTAR GENERATION 5 ANALOG/DIGITAL-READY SYSTEMS TO ONSTAR GENERATION 6 DUAL-MODE (ANALOG/DIGITAL). *TT
020730024A
Service Bulletin/Repair Instructions
DIAGNOSIS OF CRACKED OR BROKEN TRANSMISSION CASE. *TT 2006 AND PRIOR CARS AND LIGHT DUTY TRUCKS. *TT
050730021
Service Bulletin/Repair Instructions
IGNITION KEY WILL NOT REMOVE FROM IGNITION LOCK CYLINDER. *TT
040604076
Service Bulletin/Repair Instructions
INFORMATION ON UNSTABLE/ROUGH/LUMPY ENGINE IDLE, AND LOW SPEED VEHICLE SURGE, RANDOM DISTURBANCE OR VEHICLE SHUDDER. *TT
030523002
Service Bulletin/Repair Instructions
REVISED FRONT BRAKE CALIPER BRACKET MOUNTING BOLT FASTENER TIGHTENING SPECIFICATION. *TT
050601014
Service Bulletin/Repair Instructions
OIL LEAK UNDER EXTREME COLD TEMPERATURES (-34 DEGREES C) (-30 DEGREES F) OR COLDER). *TT
0508110004
Service Bulletin/Repair Instructions
CARGO COVER HANDLE BROKEN. *TT
03092005
Service Bulletin/Repair Instructions
PROGRAMMING THR ECM. *EH
050604014
Service Bulletin/Repair Instructions
DIAGNOSTIC AIDS FOR DIAGNOSTIC TROUBLE CODES P0440, P0455 AND/OR P0442 - EVAPORATIVE EMISSION (EVAP) SYSTEM LEAK. *TT
050604021
Service Bulletin/Repair Instructions
REVISED INSPECTION/MAINTENANCE (I/M) EVAPORATIVE EMISSION (EVAP) SYSTEM SET PROCEDURE. *TT
050842001
Service Bulletin/Repair Instructions
DIAGNOSTIC INFORMATION ON HEADLAMPS FLICKER OR MOMENTARILY DIM WHILE DRIVING. *TT
702
Service Bulletin/Repair Instructions
NAVIGATION RADIO SYSTEM DOES NOT HAVE COMPLETE COVERAGE. GM TECH LINKS. *TT
0508111001
Service Bulletin/Repair Instructions
BUICK EMBLEM COMING OFF GRILLE. *TT
050864003
Service Bulletin/Repair Instructions
OUTSIDE REARVIEW MIRROR VIBRATION. *TT
040232007
Service Bulletin/Repair Instructions
STEERING SYSTEM MOAN, GROAN, SHUDDER AND/OR VIBRATION TYPE NOISE DURING LOW SPEED TURNING MANEUVERS. *TT
040421004
Service Bulletin/Repair Instructions
4WD SWITCH INDICATOR LIGHTS FLASHING, 4WD INOPERATIVE, DIAGNOSTIC TROUBLE CODES C0327, P0550 SET. *TT
3152
Service Bulletin/Repair Instructions
BLOWER SPEED CHANGES ON ITS OWN. *TC UPDATE. *TT
04087
Service Bulletin/Repair Instructions
TAIL LAMPS/STOP LAMPS PRODUCT FIELD ACTION ANNOUNCEMENT. *TT ADMINISTRATIVE MESSAGE. *TT
0308111002A
Service Bulletin/Repair Instructions
PAINT CHIPPING BEHIND FRONT WHEELS/FRONT OF REAR WHEELS, DAMAGED LOWER DOOR/CLADDING AND ROCKER PANELS. *TT THIS SERVICE BULLETIN REPLACES 0308111002. *EH UPDATE. *TT
040139006A
Service Bulletin/Repair Instructions
NOISE AND OR VIBRATION WHEN A/C COMPRESSOR CYCLES. *EH UPDATED *EH
040730041
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON (SES) LIGHT ON, DIAGNOSTIC TROUBLE CODE (DTC) P0741, HARSH SHIFT, CRUISE CONTROL INOPERATIVE. *TT
040844014A
Service Bulletin/Repair Instructions
BUZZ TYPE NOISE COMING FROM REAR SPEAKERS. *TT UPDATE. *TT
040866001
Service Bulletin/Repair Instructions
REAR LICENSE PLATE POCKET GASKET LOOSE OR OUT OF POSITION. *TT UDATE. *TT
04017A
Service Bulletin/Repair Instructions
TAIL LAMP/STOP LAMP(S) MAY BECOME INOPERATIVE. GM ADMINISTRATIVE MESSAGE. *NM
030419002
Service Bulletin/Repair Instructions
SQUEAK, SQUEAL OR WHISTLE NOISE FROM FRONT AXLE. *TT
040845010
Service Bulletin/Repair Instructions
VARIOUS INTERIOR ELECTRICAL CONCERNS, IP GAUGES/LIGHTING INOPERATIVE, HVAC CONTROLS INOPERATIVE, BLOWER MOTOR INOPERATIVE, RADIO INOPERATIVE, FLASHER INOPERATIVE. *TT
040864012
Service Bulletin/Repair Instructions
FRONT OR REAR SIDE DOOR GLASS SCRATCHED. *TT
040867006
Service Bulletin/Repair Instructions
PROPER POSITIONING OF LUGGAGE CARRIER CROSS RAILS TO AVOID WINDRUSH. *TT
04017
Service Bulletin/Repair Instructions
SPECIAL POLICY ADJUSTMENT - TAIL LAMP/STOP LAMP INOPERATIVE. ANSWERS TO ASSIST IN RESPONDING TO CUSTOMER INQUIRIES. *MJ THIS IS THE FIRST PHASE WHICH WAS RELEASED JUNE 3, 2004. *TT THIS IS THE SECOND PHASE - PHASE II. *TT PHASE III. *TT
040139009
Service Bulletin/Repair Instructions
HVAC BLOWER MOTOR INOPERATIVE OR STAYS RUNNING. *TT
040602005
Service Bulletin/Repair Instructions
HIGHER THAN NORMAL ENGINE COOLANT TEMPERATURE GAUGE READINGS. *TT
040604003
Service Bulletin/Repair Instructions
VEHICLE IS DIFFICULT TO FILL WITH FUEL OR FILLING STATION PUMP SHUTS OFF BEFORE TANK IS FULL OR FUEL SPITS BACK/OUT WHEN FILLING TANK. *TT
040730035
Service Bulletin/Repair Instructions
RELEASE OF REAR TRANSMISSION MOUNT SEPARATE FROM EXHAUST MOUNT. *TT
040843007
Service Bulletin/Repair Instructions
REAR WIPER DOES NOT CLEAN REAR WINDOW. *EH
07082004
Service Bulletin/Repair Instructions
HIGHER THAT PERCEIVED NORMAL ENGINE COOLANT TEMPERATURE GAUGE READINGS WHEN OPERATING THE VEHICLE IN VERY HIGH OUT SIDE AMBIENT TEMPERATURES AND IN STOP AND GO OR SLOW MOVING TRAFFIC CONDITIONS. *EH
040601022
Service Bulletin/Repair Instructions
NEW CYLINDER BORE LINER/PISTON SLEEVE REPLACEMENT PROCEDURE. *TT
040604053
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON LIGHT ON P0133, P0172. *TT
07012004
Service Bulletin/Repair Instructions
OIL LIFE SYSTEM RESET PROCEDURES-TRUCKS. BUICK TERAZZA 2005, GMC SIERRA DENALI 2002-2003, GMC B7 CHASSIS MEDIUM DUTY 2003-2005 AND GMC 560 C-SERIES 2003-2005 *SC
030842006A
Service Bulletin/Repair Instructions
TAIL LAMP CIRCUIT BOARD NOW AVAILABLE FOR SERVICE USE. *TT
040604038
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON LIGHT ON, P1680. *TT
040604043
Service Bulletin/Repair Instructions
UNABLE TO RESET ENGINE OIL LIFE MONITOR. *TT
040863005
Service Bulletin/Repair Instructions
RATTLE NOISE UNDER HOOD. *TT
040866004
Service Bulletin/Repair Instructions
LIFTGATE GLASS UNLATCHES ON ROUGH/BUMPY ROAD SURFACES. THIS BULLETIN REPLACES PREVIOUS BULLETIN NUMBER 04-08-66-004. *TT
040421001
Service Bulletin/Repair Instructions
DELAYED ENGAGEMENT OF FRONT WHEELS DURING A SLIP CONDITION. *MJ
040601015
Service Bulletin/Repair Instructions
NEW DESIGN OIL PICK UP TUBE AND FRONT COVER. *MJ
040730022
Service Bulletin/Repair Instructions
HARSH GARAGE SHIFT FROM PARK TO DRIVE OR FROM PARK TO REVERSE WITH TRANSMISSION FLUID AT COLD AMBIENT TEMPERATURES. *EH
040844004
Service Bulletin/Repair Instructions
POP NOISE HEARD FROM REAR SPEAKERS WHEN REAR SEAT AUDIO (RSA) IS TURNED ON OR OFF (NO FIX AT TIME, FIX UNDER DEVELOPMENT). *MJ THIS SERVICE BULLETIN REPLACES 040844004. *EH
04202004
Service Bulletin/Repair Instructions
NOISE OR VIBRATION THAT CAN BE HEARD AND/OR FELT INSIDE THE CABIN AREA OF THE VEHICLE WITH THE AIR CONDITIONING RUNNING. THE NOISE IS DIRECTLY RELATED TO THE AC COMPRESSOR CYCLING AND IS EMANATING FROM THE AC ACCUMULATOR. GM VOICEMAIL EXPRESS. *TT
040523003
Service Bulletin/Repair Instructions
REVISED REAR BRAKE CALIPER BRACKET MOUNTING BOLT FASTENER SPECIFICATION. *EH
040851002
Service Bulletin/Repair Instructions
INCORRECT PAINT CODE LISTED ON SERVICE PARTS IDENTIFICATION LABEL. *MJ
03092004
Service Bulletin/Repair Instructions
POPPING NOISE HEARD THROUGH THE SPEAKER SYSTEMS WHEN THE REAR SEAT AUDIO IS TURNED ON OR OFF. *TT
020421006C
Service Bulletin/Repair Instructions
INOPERATIVE 4WD/AWD LAMPS, INOPERATIVE 4WD/AWD SYSTEM. *TT
030604033
Service Bulletin/Repair Instructions
REVISED DIAGNOSTIC TROUBLE CODE P0336. *TT UPDATE. TO INCLUDE 2004 ISUZU NQR COMMERCIAL MODELS. *TT
040138005
Service Bulletin/Repair Instructions
HVAC CONTROL MODULE MEMORY FUNCTIONS - ELIMINATION OF CLIMATE CONTROL PERSONALIZATION FEATURE. *TT
040601003
Service Bulletin/Repair Instructions
INFORMATION ON 2ND DESIGN BALANCER HUB. *TT
00156A
Service Bulletin/Repair Instructions
4.2L LL8 ENGINE ROUGH IDLE - RUN POSSIBLE P1345 OR P0016. *MJ *TT
00540B
Service Bulletin/Repair Instructions
ENGINE OIL LEAK AT INTAKE GASKET. SIT BULLETIN 1412496. *TT
00686B
Service Bulletin/Repair Instructions
AUTOMATIC VOLUME FEATURE DIAGNOSIS ON THE UQA BOSE RADIO. *TT
00731A
Service Bulletin/Repair Instructions
NOISE FROM FRONT OF VEHICLE OVER BUMPS OR UNDER LIGHT ACCELERATION. *TT
00859
Service Bulletin/Repair Instructions
DIAGNOSTIC TROUBLE CODE (DTC) C0327 WITH OR WITHOUT ADDITIONAL DIAGNOSTIC TROUBLE CODES (DTCS) SETTING. *TT *MJ
00969A
Service Bulletin/Repair Instructions
ENGINE WHISTLE NOISE. *TT
01012004
Service Bulletin/Repair Instructions
HIGH COOLANT TEMPERATURE GAUGE READINGS DURING LOW RPM OPERATION. *TT
01115A
Service Bulletin/Repair Instructions
CLUNK, RATTLE NOISE FROM FRONT OF VEHICLE OVER BUMPS. *TT
01181C
Service Bulletin/Repair Instructions
DIAGNOSTIC TROUBLE CODE (DTC) P0172. 4.2 LL8 ENGINE. *TT *MJ
01446A
Service Bulletin/Repair Instructions
SERVICE 4WD LIGHT ON NO CODES BESIDES U1000 CODES. *TT
01470
Service Bulletin/Repair Instructions
ERRATIC IDLE, IDLE SURGE, ROUGH RUN, OR NEAR STALL. *TT
01526
Service Bulletin/Repair Instructions
BELT SQUEAL. SIT BULLETIN 1406354. *TT
01526A
Service Bulletin/Repair Instructions
BELT NOISE SQUEAL OR SQUEAK. *MN *MJ
01552
Service Bulletin/Repair Instructions
ACCESSING XM RADIO IDENTIFICATION NUMBER. SIT BULLETIN 1410305. GMC DENALI 2004 INCLUDED. *TT
01573
Service Bulletin/Repair Instructions
RATTLE NOISE AND/OR TRANSMISSION FLUID LEAK FROM TRANSMISSION COOLER LINE CONTACT WITH CATALYTIC CONVERTER. *TT *MJ
01577
Service Bulletin/Repair Instructions
RADIO DISPLAYS CALIBRATION ERROR AFTER REPLACING RADIO. *MN
01578
Service Bulletin/Repair Instructions
COOLING FAN OPERATION. SIT BULLETIN 1413381. *TT
01579
Service Bulletin/Repair Instructions
OIL PAN BAFFLES DELETED. SIT BULLETIN 1413402. *TT
01623
Service Bulletin/Repair Instructions
4.2 LL8 ENGINE DIAGNOSTIC TROUBLE CODE P0016 OR P1345 WITH NO DRIVEABILITY SYMPTOMS.*MR
01654
Service Bulletin/Repair Instructions
SQUAWK OR GRUNT NOISE THAT OCCURS ON THE 2-3 UPSHIFT ON VEHICLES WITH 4L60E - M30, 4L60E M32 TRANSMISSION. *TT
01661
Service Bulletin/Repair Instructions
XM CHANNEL ZERO NOT AVAILABLE ON CERTAIN VEHICLES EQUIPPED WITH NAVIGATION STYLE RADIOS. ALSO INCLUDING GMC DENALI 2004. *TT
01662
Service Bulletin/Repair Instructions
XM ERROR ON A RADIO DISPLAY. *TT
01663A
Service Bulletin/Repair Instructions
VIBRATION NOISE FROM UNDER HOOD, SOUNDS LIKE SHEET METAL VIBRATING. *TT
01672
Service Bulletin/Repair Instructions
OIL PAN DRAIN PLUG THREADS - INFORMATION. *TT
01676
Service Bulletin/Repair Instructions
4.2 4L60E ENGINE COOLING FAN CONTACTS SHROUD AFTER REPLACING RADIATOR. *MR
01718
Service Bulletin/Repair Instructions
STARTER CLICKS - NO CRANK CONDITION. *TT
01745
Service Bulletin/Repair Instructions
4.2L LL8 ENGINE- NO CRANK, NO START. *MR
01746
Service Bulletin/Repair Instructions
4.2 5.3 LL8 LM4 ENGINE WITH DIAGNOSTIC TROUBLE CODE P2120 OR P2122 OR P2123 OR P2127 OR P2128. *MR
01762
Service Bulletin/Repair Instructions
4.2 LL8 ENGINE ELECTRONIC POWERTRAIN CONTROL MODULE (PCM) RESTRICTION. *MR
01799
Service Bulletin/Repair Instructions
NO VOLUME FROM RADIO IN COLD AMBIENT TEMPERATURES FOR 20-30 MINUTES. *MR
01802A
Service Bulletin/Repair Instructions
APP SENSOR 2 AND/OR TP SENSOR 2 SIGNAL CIRCUIT VOLTAGES DROP. *TT
01816
Service Bulletin/Repair Instructions
DIAGNOSTIC TROUBLE CODE P0130. *MR *TT
01843
Service Bulletin/Repair Instructions
CALIBRATION FOR IMPROVED TRANSFER CASE OPERATION IN AWD MODE. *TT
01899
Service Bulletin/Repair Instructions
INITIALIZATION AND RE-INITIALIZATION OF SUNROOF MDIV MOTOR. ALSO INCLUDING 2003 BUICK RAINIER, AND 2004 CHEVROLET TRAILBLAZER EXT. *MR
01900
Service Bulletin/Repair Instructions
UNDER HOOD FUSE BLOCK - 125 AMP MEGA FUSE BLOWN. ALSO INCLUDING BUICK RAINIER 2002, 2003. *MR
01917
Service Bulletin/Repair Instructions
FALSE DIAGNOSTIC TROUBLE CODE (DTC) P1680. *TT
01925
Service Bulletin/Repair Instructions
TECH 2 ENGINE DATA INCORRECT- GEN L-TERMINAL SIGNAL COMMAND DATA PARAMETER. *MR
01968A
Service Bulletin/Repair Instructions
DIAGNOSTIC TROUBLE CODE (DTC) P0171. *TT
01973
Service Bulletin/Repair Instructions
HARSH SHIFTS FROM PARK TO DRIVE OR DRIVE TO REVERSE (GARAGE SHIFT). WORSE IN COLD AMBIENT TEMPERATURES. *NM
02009
Service Bulletin/Repair Instructions
NOISE AND/OR VIBRATION DURING AIR CONDITIONER OPERATION. *MR
02044
Service Bulletin/Repair Instructions
NO SOUND FROM RADIO OR RADIO WILL NOT PROGRAM. *TT
02053
Service Bulletin/Repair Instructions
INFORMATION ON RESURFACING THE PARK BRAKE PORTION OF THE REAR BRAKE ROTOR. *TT
02060
Service Bulletin/Repair Instructions
NO AUDIO AND RADIO DISPLAY INOPERATIVE OR CLOCK RESETS. *TT
02068
Service Bulletin/Repair Instructions
NO START WITH DIAGNOSTIC TROUBLE CODE (DTC) P1626 OR P1631. ALSO INCLUDES 1998-2004 CHEVROLET, GMC FULL SIZE TRUCKS/ UTILITIES/ VANS. *TT
02080
Service Bulletin/Repair Instructions
REPEAT HVAC ACTUATOR REPLACEMENT. *TT
02086
Service Bulletin/Repair Instructions
4L60E, 4L65E INTERMITTENT NEUTRAL FROM A STOP OR STEADY SPEED. *TT
02090
Service Bulletin/Repair Instructions
RADIO PARTS RESTRICTION WHEN CALLING SPECMO EXCHANGE CENTER. TO INCLUDE 2003-2004 CHEVROLET AND GMC FULL SIZE UTILITIES AND FULL SIZE PICK-UP. *TT
02117
Service Bulletin/Repair Instructions
TCCM WILL NOT PROGRAM THROUGH TIS. *MJ
02129
Service Bulletin/Repair Instructions
ROUGH IDLE OR IDLE SHAKE AT TIMES. *TT
02140
Service Bulletin/Repair Instructions
WHEN ATTEMPTING TO TURN THE KEY TO START THE VEHICLE, YOU MAY EXPERIENCE HARD OR INTERMITTENT MECHANICAL BINDING IN THE IGNITION CYLINDER. *TT
040730002
Service Bulletin/Repair Instructions
RATTLE TYPE NOISE COMING FROM UNDER THE VEHICLE. *TT
040848002
Service Bulletin/Repair Instructions
AVAILABILITY OF NEW DESIGN WINDSHIELD AND FRONT DOOR GLASS. *TT
0810B
Service Bulletin/Repair Instructions
TICK NOISE AT IDLE. *TT
1528102
Service Bulletin/Repair Instructions
02-04 4.2L LL8 DIAGNOSTIC TROUBLE CODE P0171. *MJ
1531018
Service Bulletin/Repair Instructions
HVAC MODE ACTUATOR CAM GEAR ALIGNMENT IS INCORRECT AFTER REPLACEMENT. *MJ
3016
Service Bulletin/Repair Instructions
VARIOUS ELECTRICAL CONCERNS. *TT
3018
Service Bulletin/Repair Instructions
ENGINE CYLINDER HEAD CUP PLUG COOLANT LEAK. *MJ
3019A
Service Bulletin/Repair Instructions
DIAGNOSTIC TROUBLE CODE P0171 . *SC SERVICE ENGINE SOON LIGHT DUE TO DIAGNOSTIC TROUBLE CODE P0171. *TT
3031
Service Bulletin/Repair Instructions
INTERMITTENT P0483 DIAGNOSTIC TROUBLE CODE. *TT
3037
Service Bulletin/Repair Instructions
INTERMITTENT REAR LIFTGLASS CONCERNS. *TT
3042
Service Bulletin/Repair Instructions
CRUISE CONTROL DISENGAGES AFTER ACCELERATING. *TT
3043
Service Bulletin/Repair Instructions
FUEL SPLASH FROM FILLER NECK AFTER FILLING TANK AFTER 04-06-04-003. *TT
3044
Service Bulletin/Repair Instructions
LOCATION OF THE HEADLAMP DRIVER MODULE (HDM). *TT
3059
Service Bulletin/Repair Instructions
RATTLE NOISE IN FRONT SUSPENSION OVER SMALL BUMPS, CLUNK OR LOOSE LUMBER TYPE NOISE OVER UNEVEN/WASH BOARD ROADS. *TT
3076
Service Bulletin/Repair Instructions
REPLACEMENT GOODWRENCH ENGINES - PARTS WHICH MUST BE SWAPPED FROM ORIGINAL ENGINE. *TT
3086
Service Bulletin/Repair Instructions
WHISTLE NOISE FROM THE THROTTLE BODY AREA ON LIGHT THROTTLE ACCELERATION ON VEHICLES WITH GEN III ENGINES AND ELECTRONIC THROTTLE. *TT
3090
Service Bulletin/Repair Instructions
UNABLE TO PERFORM SET UP NEW ONSTAR ON VEHICLES WITH GEN 6.05 HARDWARE. *SC
3095
Service Bulletin/Repair Instructions
OPERATION OF REAR GLASS RELEASE KEY CYLINDER. TO INCLUDE 2005 TRAILBLAZER AND BUICK RAINIER. *SC
3106
Service Bulletin/Repair Instructions
XM RADIO WAS WORKING PRIOR TO JULY 26, 2004 AND IT IS INOPERATIVE NOW. *JB
3108
Service Bulletin/Repair Instructions
FASTENER MISSING ON THE REAR CHMSL APPLIQUE. (TO INCLUDE 2005 CHEVROLET TRAILBLAZER AND 2005 BUICK RAINIER) *SC
3113
Service Bulletin/Repair Instructions
GEN 6 VEHICLES IN MOUNT AIRY, NC CANNOT CONNECT TO ONSTAR OR EMERGENCY SERVICES. *SC
3124
Service Bulletin/Repair Instructions
UPPER AND LOWER INTERMEDIATE SHAFT PARTS RESTRICTION. *SC
3142
Service Bulletin/Repair Instructions
BROKEN HEAD BOLT REPAIR. *TC
3151
Service Bulletin/Repair Instructions
INSIDE REAR VIEW MIRROR DOES NOT DISPLAY AMBIENT TEMPERATURE WITH CJ2 OPTION. *TC
3172
Service Bulletin/Repair Instructions
MULTIPLE ELECTRICAL CONCERNS AND DIAGNOSTIC TROUBLE CODE U1064. VARIOUS MODELS INCLUDING 2005 BUICK RAINIER AND 2005 CHEVROLET TRAILBLAZER. *TT
3179
Service Bulletin/Repair Instructions
AUTOMATIC DUAL ZONE HVAC BATTERY DRAW SUPPLEMENT TO 02-01-39-007A. *TT
030842014
Service Bulletin/Repair Instructions
NEW TURN SIGNAL FLASHER MODULE AVAILABILITY. *TT
030844020
Service Bulletin/Repair Instructions
BOSE RADIO MAY HAVE POOR FIDELITY. *TT
030863003
Service Bulletin/Repair Instructions
RATTLE FROM FRONT OF VEHICLE. *TT
11202003
Service Bulletin/Repair Instructions
RATTLE NOISE UNDERNEATH THE VEHICLE OR AN AUTOMATIC TRANSMISSION FLUID LEAK. *EH
00651B
Service Bulletin/Repair Instructions
REAR BRAKE LIGHT BULB OUT. *TT
01381
Service Bulletin/Repair Instructions
SPECIAL ACOUSTIC LAMINATED WINDSHIELD AND FRONT DOOR SIDE GLASSES. SERVICE VME. *TT
01390
Service Bulletin/Repair Instructions
XM RADIO MUST BE TUNED TO CHANNEL 1 THROUGH 66 DURING ACTIVATION ATTEMPT. 2004 CHEVROLET CANYON, GMC DENALI, GMC COLORADO ALSO INCLUDED. *TT
01402A
Service Bulletin/Repair Instructions
4.2L LL8 DIAGNOSTIC TROUBLE CODE (DTC) P0410. *TT
01416
Service Bulletin/Repair Instructions
ENGINE OIL LEAK AFTER CRANK SHAFT BALANCER REPLACEMENT. *TT
01459
Service Bulletin/Repair Instructions
HVAC MODE ACTUATOR CAM GEAR ALIGNMENT IS INCORRECT AFTER REPLACEMENT. *TT
030089036
Service Bulletin/Repair Instructions
DEALER INSTALLED REGULAR PRODUCTION ACCESSORIES (RPA). *TT
102103
Service Bulletin/Repair Instructions
RUNNING BOARD PART SHIPPING DELAY. GM VOICEMAIL LOG. *TT
030604060
Service Bulletin/Repair Instructions
INFORMATION ON NEW SPARK PLUGS AND GAPPING. VARIOUS MODELS INCLUDING PONTIAC GTO 2004. *TT
510
Service Bulletin/Repair Instructions
2004 SECONDARY AIR INJECTION SYSTEM- IN 6 CYLINDER ENGINE INCORPORATES A NEW AIR PUMP AND AN ELECTRONIC AIR SHUT OFF VALVE. *SC
092203
Service Bulletin/Repair Instructions
TAIL LAMP CIRCUIT BOARD PART NUMBER INFORMATION. GM VOICEMAIL LOG. *TT
030864032
Service Bulletin/Repair Instructions
AVAILABILITY OF REPLACEMENT PARTS FOR OUTSIDE REARVIEW MIRROR. *TT
030864033
Service Bulletin/Repair Instructions
AVAILABILITY OF REPLACEMENT MIRROR ACTUATOR. *TT
080703
Service Bulletin/Repair Instructions
SHIPMENT OF THE NEW 2004 BUICK RAINIER. VME MESSAGE. *TT
030421006
Service Bulletin/Repair Instructions
SERVICE 4WD LIGHT ON, 4WD INOPERATIVE, HARSH ENGAGEMENT OF 4WD, NO COMMUNICATION WITH TRANSFER CASE CONTROL MODULE (TCCM), TCCM DIAGNOSTIC TROUBLE CODE (DTC) C0550 SET. *TT
01432
Service Bulletin/Repair Instructions
AUTOMATIC TRANSMISSION POOR ACCELERATION, PERFORMANCE. *TT
01444
Service Bulletin/Repair Instructions
XM DEALER ASSISTANCE LINE INFORMATION. *TT
02133
Service Bulletin/Repair Instructions
SNOW PLOW PACKAGE QUESTIONS. ALSO TO INCLUDE 2002 - 2004 CHEVROLET, GMC FULL SIZE AND MID-SIZE PICKUP S AND SPORT UTILITIES. *TT
1750177
Service Bulletin/Repair Instructions
ABS BRAKE SVC AND 4WD LIGHT ON HVAC BLOWER INOPERATIVE. *AK
1996584
Service Bulletin/Repair Instructions
BOOM/RUMBLING NOISE AT HIGHWAY SPEED *NJ
3002
Service Bulletin/Repair Instructions
4L60E/4L65E INTERMITTENT NEUTRAL CONDITION WHILE ACCELERATING FROM A STOP OR WHILE DRIVING. *TT 1999-2006 GM CARS, LIGHT DUTY TRUCKS AND UTILITIES. *TT
3046A
Service Bulletin/Repair Instructions
FUEL GAUGE FLUCTUATION IN PARK OR NEUTRAL. *TT
3056
Service Bulletin/Repair Instructions
CHECK ENGINE LIGHT WITH A P0300 DUE TO 2-4 CYLINDERS MISFIRING ON THE SAME BANK OF THE ENGINE. *TT
3061C
Service Bulletin/Repair Instructions
DIAGNOSTIC TROUBLE CODE C0327 WITH OR WITHOUT ADDITIONAL DIAGNOSTIC TROUBLE CODES SETTING. *TT
3077
Service Bulletin/Repair Instructions
TICK NOISE AT IDLE. *TT
3079
Service Bulletin/Repair Instructions
INTERMITTENT P0483 DIAGNOSTIC TROUBLE CODE. *TT
3083
Service Bulletin/Repair Instructions
KEY MAY NOT TURN OR BIND IN THE IGNITION. *TT
3089
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON LIGHT AND REDUCED ENGINE POWER WITH A DIAGNOSTIC TROUBLE CODE P1516. DIAGNOSTIC TROUBLE CODES P0120, P0220, P1514, P1515, P1518 AND P2135 MAY ALSO BE PRESENT. *TT
3110A
Service Bulletin/Repair Instructions
WASHER MOTOR FOR THE FRONT WIPERS CONTINUOUSLY RUNS WHILE THE KEY ON. *SC UPDATE. *TT
3110C
Service Bulletin/Repair Instructions
WIPER/WASHER WILL NOT SHUT OFF OR OTHER POSSIBLE ISSUES. *TT
3116
Service Bulletin/Repair Instructions
ENGINE STALLS WHEN AIR CONDITIONING IS TURNED ON AT IDLE. (TO INCLUDE 2005 CHEVROLET TRAILBLAZER, 2005 OLDSMOBILE BRAVADA, AND BUICK RAINIER) *SC UPDATED 01-26-07. *KB
3136
Service Bulletin/Repair Instructions
SLIP CONDITION IN 2ND, 3RD, OR 4TH. DAMAGED 2-4 OR 3-4 CLUTCH. *KB UPDATED 10/31/07. *NJ
3137
Service Bulletin/Repair Instructions
SERVICE 4WD LIGHT ON AND NO COMMUNICATION WITH TRANSFER CASE CONTROL MODULE. *EH
3138
Service Bulletin/Repair Instructions
REDUCED POWER LIGHT ON AND DIAGNOSTIC TROUBLE CODE P1680 P1221 AND OR P1271 STORED IN THE POWERTRAIN CONTROL MODULE. *EH
3150
Service Bulletin/Repair Instructions
CYLINDER LINER REPLACEMENT INFORMATION - INLINE TRUCK ENGINES. *EH
3164A
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON LIGHT DUE A DIAGNOSTIC TROUBLE CODE P0606 DIAGNOSTIC TROUBLE CODE, OPERATE IN REDUCED ENGINE POWER MODE, AND POTENTIALLY STALL. *TT
3170
Service Bulletin/Repair Instructions
HARSH 1-2 SHIFT. *EH
3177
Service Bulletin/Repair Instructions
REPEAT FRONT AXLE FLUID LEAK. *EH
3192
Service Bulletin/Repair Instructions
REDUCED ENGINE POWER MESSAGE AND/OR CHECK ENGINE LIGHT WITH ANY COMBINATION OF THE FOLLOWING DIAGNOSTIC TROUBLE CODES: P0107, P0112, P0452, P1120, P1220, P1221, P1271, P1275, P1280, P1481, P1515, P1540, P1633, P1635, P1639 AND P1682 POWERTRAIN CONTROL MODULE REPEAT. *TT
3198
Service Bulletin/Repair Instructions
NO CRUISE CONTROL AND DIAGNOSTIC TROUBLE CODE P0741. *EH
3204B
Service Bulletin/Repair Instructions
INSTALLATION OF AN AFTERMARKET TRAILER BRAKE MODULE. *TT
3209
Service Bulletin/Repair Instructions
EXHAUST MOAN AT IDLE OR PARKING LOT MANEUVERS. *EH
3216
Service Bulletin/Repair Instructions
ERRATIC OPERATION OF PERSONALIZATION WITH IGNITION CYCLE. *EH
3225
Service Bulletin/Repair Instructions
OUTSIDE REAR VIEW MIRROR MOVES IN THE WRONG DIRECTION COMPARED TO THE SWITCH. *EH
3232
Service Bulletin/Repair Instructions
1999 - 2005 GEN II COLD ENGINE MISFIRE AT IDLE WITH POSSIBLE P0171 AND/OR P0174. *TT
3263
Service Bulletin/Repair Instructions
125A MEGA FUSE OPENS WHEN ATTEMPTING TO JUMP START. *EH
3265
Service Bulletin/Repair Instructions
UNEVEN APPEARANCE OR LEAN FROM DRIVERS TO PASSENGER SIDE RPO G67. *EH
3274
Service Bulletin/Repair Instructions
INSTALLATION OF A POWER STEERING HOSE TO A NEW STEERING GEAR. *EH
3300
Service Bulletin/Repair Instructions
HORN INOPERATIVE AT TIMES. *KB
3300C
Service Bulletin/Repair Instructions
APPLICATION OF HORN AT HORN PAD INOPERATIVE. RKE FUNCTION FOR PANIC ALARM WORKS. *TT
3317A
Service Bulletin/Repair Instructions
HEADLAMPS FLICKER OR DIM WHILE DRIVING. *TT
3329
Service Bulletin/Repair Instructions
SURGE, CHUGGLE OR BUCK WHILE DRIVING DOWNHILL (APPROXIMATELY 1500 - 3000 FEET ABOVE SEA LEVEL) AT HIGHWAY SPEEDS WITH THE CRUISE CONTROL ON. *TT
3330
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON (SES) LIGHT DUE TO A P0171 DIAGNOSTIC TROUBLE CODE. *TT
3334A
Service Bulletin/Repair Instructions
B3606 HEATED SEAT(S) INOPERATIVE AND/OR ADJUSTABLE PEDALS DO NOT RECALL. *TT
3335
Service Bulletin/Repair Instructions
SUPPLEMENT TO CAMPAIGN 04087 / SCREWS BREAK IN THE TAIL LAMP HOUSING. *SC
3351
Service Bulletin/Repair Instructions
INTERMITTENT MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODE (DTC) C0374 OR ERRATIC 4WD/AWD OPERATION. *TT
3373
Service Bulletin/Repair Instructions
SIR LIGHT ON STEADY AFTER BULB TEST AND NO DIAGNOSTIC TROUBLE CODES (DTCS). *TT
3405
Service Bulletin/Repair Instructions
ENGINE IS HARD TO START AFTER FILLING THE FUEL TANK. *TT
3420A
Service Bulletin/Repair Instructions
PING, POP OR CLICK NOISE FROM UNDER THE REAR. *SC
3444
Service Bulletin/Repair Instructions
SERVICE VME-TCC SURGE OR SHUDDER, INVESTIGATION OF WATER INTRUSION INTO THE TRANSMISSION. *SC
3516
Service Bulletin/Repair Instructions
VIBRATION FELT AND HEARD AT LOW RPM DURING PARKING LOT MANEUVERS. *TT
3522
Service Bulletin/Repair Instructions
SERVICE VME - FUEL SYSTEM LEAN DTCS P0101 P0171 P0174. *TT
3577
Service Bulletin/Repair Instructions
NO CRANK NO START NO DIAGNOSTIC TROUBLE CODES. *TT
3614
Service Bulletin/Repair Instructions
P0300 DUE TO RANDOM MISFIRES NOT FELT - POSSIBLE ACCESSORY PULLEY. *TT
3659A
Service Bulletin/Repair Instructions
SES LIGHT AFTER INTERNAL ENGINE REPAIRS DUE DTC P0016 OR P1345. *TT
3680
Service Bulletin/Repair Instructions
AUTOMATIC HEADLAMP DEFEAT INOPERATIVE AFTER BCM REPLACEMENT. *TT
3697
Service Bulletin/Repair Instructions
ANTI-LOCK BRAKING SYSTEM (ABS) AND SERVICE ENGINE SOON (SES) LIGHT ON WITH DIAGNOSTIC TROUBLE CODES C0055 B0540 SPEEDOMETER INOPERATIVE. TO INCLUDE 2005-2006 SAAB 9-7X. *TT
3756A
Service Bulletin/Repair Instructions
IPC GAUGES AND AC INOPERATIVE, SEVERAL INDICATORS ILLUMINATE DTCS U1016 U1000. *TT
3779
Service Bulletin/Repair Instructions
SQUEAK NOISE ON BRAKE APPLY. *TT
3928
Service Bulletin/Repair Instructions
BIND OR SHUDDER ON TURNS. *KB
3999
Service Bulletin/Repair Instructions
LIFTGATE GLASS WILL NOT LOCK UNLESS LOCK IS PRESS A SECOND TIME. *KB
4338
Service Bulletin/Repair Instructions
LIGHTS FLICKER ERRATIC OPERATION OF VEHICLES ELECTRONICS. *KB
4486
Service Bulletin/Repair Instructions
ONE OF THE FOLLOWING CONCERNS WHEN PROGRAMMING THE MILEAGE OR THE HOURS INTO AN EXCHANGE INSTRUMENT PANEL CLUSTER THAT IS RECEIVED FROM AN ELECTRONIC SERVICE CENTER (ESC). *NJ
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.