17-NA-073
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
Vehicle report
1999 CADILLAC ESCALADE
Service bulletins
96 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
04-06-04-051F
Service Bulletin/Repair Instructions
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
05-00-89-072E
Service Bulletin/Repair Instructions
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
PIP4723F
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
N202307080 01
Service Bulletin/Repair Instructions
Service Update Bulletin (Labor Codes Added). Certain vehicles may have a condition where the engine control module (ECM) software allows the Auto Stop to occur at a state of charge below 65%. Auto Stop is supposed to be inhibited at 65% to protect against excessive battery wear and discharge. Dealers are to reprogram the ECM.
PIP4723D
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIC4696E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code. The PI update to version D is to advise the unlock procedure is temporarily unavailable. E version update is to add administrative details.
17NA073
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
PIC4696D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code. The PI update to version D is to advise the unlock procedure is temporarily unavailable.
PIT3098G
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a lean to the left or right. Technician will need to measure fender wheel-opening heights, front and rear, to quantify vehicle lean. Fender wheel-opening heights are related to, but distinct from, trim height. The front wheel-opening height is known as P height, and the rear wheel-opening height is known as R height. Adjust and heights that are out of specification. After all adjustments are done, perform a front-end alignment and check headlight aim.
PIP3366C
Service Bulletin/Repair Instructions
This Preliminary information communicates to the dealer technician thatLight Duty Trucks equipped with automatic transmissions and 4 wheel drive may exhibit a condition of grinding/ratcheting type noise when shifting the automatic transmission into park while the transfer case is in 4 wheel drive low (4LO) range. Dealers technician's are advised this condition should be deemed a normal characteristic of 4WD low operation.
PIC4696C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco Theft Lock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code.
PIT3098F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a lean to the left or right. Technician will need to measure fender wheel-opening heights, front and rear, to quantify vehicle lean. Fender wheel-opening heights are related to, but distinct from, trim height. The front wheel-opening height is known as P height, and the rear wheel-opening height is known as R height. Adjust and heights that are out of specification. After all adjustments are done, perform a front-end alignment and check headlight aim.
PIP4723C
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP4723B
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
16NA260
Service Bulletin/Repair Instructions
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.
PIC4696B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code.
PIP5346
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about cooler line fittings that come with the 4T65E General Motors remanufactured transmission may not be the same as Original equipment manufacturer quick connect verses inverted flare. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIC4696A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code.
PIP4404F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.
PIT3098E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a lean to the left or right. Technician will need to measure fender wheel-opening heights, front and rear, to quantify vehicle lean. Fender wheel-opening heights are related to, but distinct from, trim height. The front wheel-opening height is known as P height, and the rear wheel-opening height is known as R height. Adjust and heights that are out of specification. After all adjustments are done, perform a front-end alignment and check headlight aim.
Recalls
Service Bulletin/Repair Instructions
Vehicle Recalls
05-06-04-035D
Service Bulletin/Repair Instructions
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
130089004I
Service Bulletin/Repair Instructions
Car and Truck Fix it Right the First Time Issues
99-08-51-007F
Service Bulletin/Repair Instructions
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
PI0281D
Service Bulletin/Repair Instructions
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
PIC5913
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Supplemental Inflatable Restraint lamp, Service Vehicle Soon lamp on and/or radio locked, possibly after module replacement. Technician will need to check for an incorrect or non-existent VIN number in modules that require them. Technician should ensure that all modules that are replaced are programmed per currently published Service Information. Technician should also check the Sensing and Diagnostic Module part number if it was replaced.
130089009
Service Bulletin/Repair Instructions
Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules
01-08-49-017B
Service Bulletin/Repair Instructions
This technical bulletin provides a revision of 01-08-49-017A to add new pricing information and payment terms.
00-00-89-027G
Service Bulletin/Repair Instructions
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
PIP3720D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
PIP5072
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have slip in forward ranges immediately after replacing the input housing. Technician will inspect the 3-4 clutches and the forward clutch oil feed passages for leakage between circuits. Technician should apply regulated compressed air to the 3-4 clutch feed hole and the forward clutch feed hole one at a time with the input housing. Technician will need to replace the input housing if there is an air leak 3-4 clutches.
08089-B
Service Bulletin/Repair Instructions
GENERAL MOTORS CORP: SPECIAL COVERAGE ADJUSTMENT; ANALOG ONSTAR DEACTIVATION. *PE UPDATED 2/17/09. *PE
08-089
Service Bulletin/Repair Instructions
BUICK CADILLAC CHEVROLET GMC HUMMER OLDSMOBILE PONTIAC SAAB SATURN SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. FCC RULED IN 2002 WIRELESS CARRIERS WOULD NO LONGER RE REQUIRED TO SUPPORT ANALOG WIRELESS NETWORK STARTING IN 2008. *PE CSC LETTER WAS RECEIVED. UPDATED 12/1/08. *PE
3340
Service Bulletin/Repair Instructions
LEFT FRONT AXLE SHAFT DIFFICULT TO REMOVE. AXLE DIFFERENTIAL LEAK SEAL SHAFT. *KB
020525006
Service Bulletin/Repair Instructions
ANTILOCK BRAKE (ABS) ACTIVATION AT LOW SPEEDS. *TT
000089008E
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY WANT TO TOW THEIR VEHICLE BEHIND ANOTHER VEHICLE WITH ALL FOUR TIRES ONT HE GROUND. THIS BULLETIN PROVIDES INFORMATION REGARDING RECREATIONAL (DINGHY) TOWING FOR CERTAIN VEHICLES INCLUDING 1988-2004 CHEVROLET AND GMC LIGHT DUTY TRUCKS. *TT
010730038B
Service Bulletin/Repair Instructions
THE SERVICE ENGINE SOON LAMP IS ILLUMINATED, NO 3RD AND 4TH GEAR, THE TRANSMISSION DOES NOT SHIFT CORRECTLY, THE TRANSMISSION FEELS LIKE IT SHIFTS TO NEUTRAL OR A LOSS OF DRIVE OCCURS. *TT
010730002D
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP (MIL) ON, TRANSMISSION STUCK IN THIRD GEAR, INSTRUMENT CLUSTER INOPERATIVE. *TT UPDATED *EH 2006 AND PRIOR GM PASSENGER CARS AND LIGHT DUTY TRUCKS. *SC
020730024A
Service Bulletin/Repair Instructions
DIAGNOSIS OF CRACKED OR BROKEN TRANSMISSION CASE. *TT 2006 AND PRIOR CARS AND LIGHT DUTY TRUCKS. *TT
020307002
Service Bulletin/Repair Instructions
REVISED FRONT CASTER AND CAMBER ADJUSTMENT PROCEDURE. ORIGINAL NOT YET RECEIVED. *TT
040604088
Service Bulletin/Repair Instructions
REPLACEMENT OF CONNECTOR WHEN REPLACING FUEL TANK MODULE/FUEL PUMP MODULE. *TT
000730022B
Service Bulletin/Repair Instructions
A NO REVERSE, NO SECOND GEAR, OR NO FOURTH GEAR CONDITION. *TT UPDATED *EH
01599
Service Bulletin/Repair Instructions
4L60E, 4L65E FORWARD AND LOW REVERSE WAVED STEEL CLUTCH PLATE APPEARANCE CHANGE. *TT
02038
Service Bulletin/Repair Instructions
DIAGNOSTIC TROUBLE CODE B1000. *MR
3121
Service Bulletin/Repair Instructions
EXHAUST VIBRATION RESONANCE OR MOAN. (2004-2005 GMC DENALI) *SC
3121A
Service Bulletin/Repair Instructions
EXHAUST VIBRATION RESONANCE OR MOAN 99-05 FULL SIZE TRUCKS AND UTILITY VEHICLES WITH GEN 3 V-8 ENGINES. *TC
01409
Service Bulletin/Repair Instructions
THE NVG 136 ALL WHEEL DRIVE (AWD) TRANSFER CASE AND THE 236 AND 246 NVG SELECTABLE TRANSFER CASE SHUDDER ON TURNS. *TT
01410
Service Bulletin/Repair Instructions
POOR PERFORMANCE FROM A STOP IN 2WD, AUTO OR 4WD HI. 2003, 2003 CADILLAC EXT ALSO INCLUDED. *TT
000089008B
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY WANT TO TOW THEIR VEHICLE BEHIND ANOTHER VEHICLE WITH ALL FOUR TIRES ONT HE GROUND. THIS BULLETIN PROVIDES INFORMATION REGARDING RECREATIONAL (DINGHY) TOWING FOR CERTAIN VEHICLES INCLUDING 1988-2004 CHEVROLET AND GMC LIGHT DUTY TRUCKS. *TT
990730022A
Service Bulletin/Repair Instructions
SHIFT STABILIZATION AND TOW/HAUL MODE FEATURE FOR HYDRA-MATIC 4L60-E/4L65-E AND 4L80-E/4L85-E TRANSMISSIONS. *TT
000604003B
Service Bulletin/Repair Instructions
ROUGH IDLE AFTER START, AND/OR A SERVICE ENGINE SOON (SES) LIGHT. VARIOUS MODELS INCLUDING THE 1995 CHEVROLET AND GMC S/T MODELS. *TT
020421005A
Service Bulletin/Repair Instructions
SLIPS IN 4-WHEEL DRIVE, NOISE, VIBRATION, LEAKS, HOT ODOR. *TT
020525006A
Service Bulletin/Repair Instructions
ANTILOCK BRAKE (ABS) ACTIVATION AT LOW SPEEDS ON VARIOUS MODELS INCLUDING THE 1995 AND 1996 ENVOY. *TT
990730016A
Service Bulletin/Repair Instructions
DIAGNOSTIC INFORMATION FOR INTERMITTENT TRANSMISSION DOWNSHIFT, SLIP, BUSY/CYCLING TCC OR NOISY COOLING FAN. *TT
020421005
Service Bulletin/Repair Instructions
SOME VEHICLES WILL NOT MOVE WHEN 4-WHEEL DRIVE IS REQUESTED, NOISE, SHUDDER, POOR PERFORMANCE, TRANSMISSION / TRANSFER CASE SLIPS, TRANSMISSION WILL NOT UPSHIFT, SLIPS IN 4-WHEEL DRIVE. *TT
020525002
Service Bulletin/Repair Instructions
SUBJECT REGARDING REVISED WHEEL SPEED SENSOR REPLACEMENT PROCEDURE. *TT
020234001
Service Bulletin/Repair Instructions
SUBJECT REGARDING TIE ROD REPLACEMENT- INNER PROCEDURE. *TT
020451003
Service Bulletin/Repair Instructions
SUBJECT REGARDING REVISED DIAGNOSTIC TROUBLE CODE B2725. *TT
010730023B
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY COMMENT ON A HARSH 1-2 UPSHIFT AND THE CHECK ENGINE LIGHT OR SERVICE ENGINE SOON INDICATOR IS ILLUMINATED AND DIAGNOSTIC TROUBLE CODE P1870 SET. *TT
020524001
Service Bulletin/Repair Instructions
SUBJECT REGARDING REVISED DRUM BRAKES COMPONENT SPECIFICATIONS FOR PICKUP AND UTILITY MODELS. *TT
000604003A
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY COMMENT ON ROUGH IDLE AFTER START UP, ESPECIALLY AFTER SETTING OVERNIGHT. *TT
010730038
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY COMMENT THAT THE SERVICE ENGINE SOON LAMP IS ILLUMINATED, NO 3RD AND 4TH GEAR, THE TRANSMISSION DOES NOT SHIFT CORRECTLY, THE TRANSMISSION FEELS LIKE IT SHIFTS TO NEUTRAL OR A LOSS OF DRIVE OCCURS. *TT
010605006
Service Bulletin/Repair Instructions
SUBJECT REGARDING EXHAUST SYSTEM RUMBLE / RATTLE NOISE. *JG
010730023A
Service Bulletin/Repair Instructions
INFORMATION REGARDING HARSH 1-2 UPSHIFT, SERVICE ENGINE SOON, MALFUNCTION INDICATOR LAMP, OR CEL ILLUMINATED, DIAGNOSTIC TROUBLE CODE P1870 SET. (1996-2000 CHEVROLET AND GMC LIGHT DUTY TRUCK MODELS) *YH
180901
Service Bulletin/Repair Instructions
CUSTOMERS MAY COMPLAIN THAT THEIR CENTER CONSOLE LOCK IS NOT OPERATIONAL. *SLC
010856004A
Service Bulletin/Repair Instructions
INFORMATION REGARDING SECURITY LAMP ILLUMINATION ON THE INSTUMENT PANEL, ENGINE STALLS. *YH
010856004
Service Bulletin/Repair Instructions
INFORMATION REGARDING SECURITY LAMP ILLUMINATING ON THE INSTRUMENT PANEL, ENGINE STALL, NO START, AND DIAGNOSIC TROUBLE CODE B2960. *SLC
0108110003
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY COMMENT THAT THE DOOR TRIM PANELS, DOOR SWITCH PLATES, AND FLOOR CONSOLE WOODGRAIN TRIM EXHIBIT A CLOUDY AND / OR A MILKY APPEARANCE. *TT
010730023
Service Bulletin/Repair Instructions
SOME OWNERS WITH VEHICLES BUILT BEFORE JANUARY 15,1999 MAY COMMENT ON A HARSH 1-2 UPSHIFT AND MAY ALSO HAVE A CHECK ENGINE LIGHT. *ET
000089008A
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY WANT TO TOW THEIR VEHICLE BEHIND ANOTHER VEHICLE WITH ALL FOUR TIRES ONT HE GROUND. THIS BULLETIN PROVIDES INFORMATION REGARDING RECREATIONAL (DINGHY) TOWING FOR CERTAIN VEHICLES INCLUDING THE 1996 THROUGH 2000 TOYOTA CAVALIER. *TT
010730002B
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP (MIL) IS ON; THE TRANSMISSION IS STUCK IN THIRD GEAR; AND / OR THE INSTRUMENT CLUSTER IS INOPERATIVE. *TT
010730012
Service Bulletin/Repair Instructions
INFORMATION PERTAINING TO THE NEW CONTROL VALVE BODY, SPACER PLATE AND GASKETS FOR THE 4L60-E AUTOMATIC TRANSMISSION. *TT
00152
Service Bulletin/Repair Instructions
CAMPAIGN PARTS BULLETIN REGARDING FMVSS NECK EXTENSION REQUIREMENTS. *TT
00044
Service Bulletin/Repair Instructions
SUBJECT REGARDING FMVSS NECK EXTENSION REQUIREMENTS. *TT
000863007
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY COMMENT THAT THE HOOD SHEET METAL FLUTTERS OR VIBRATES WHEN DRIVING AT VARIOUS SPEEDS. *TT
00074
Service Bulletin/Repair Instructions
SOME VEHICLES MAY HAVE THE POTENTIAL OF EXHIBITING A BATTERY DRAIN CONDITION WHEN A VEHICLE THEFT EVENT CAUSES A PHONE CALL TO BE INITIATED BY THE ONSTART AUTOMATIC THEFT NOTIFICATION FEATURE, AND THE CALL IS NOT COMPLETED. *TT
000604014
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY COMMENT ON HARD, NO, OR SLOW START, BACKFIRE OR KICKBACK DURING CRANK / START, GRINDING OR UNUSUAL NOISES DURING CRANK, DIAGNOSTIC TROUBLE CODE P0338. *TT
000604003
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY COMMENT ON ROUGH IDLE AFTER START UP, AND / OR A SERVICE ENGINE SOON (SES) LIGHT ILLUMINATED. *TT
000866001
Service Bulletin/Repair Instructions
SUBJECT REGARDING WATER INTRUSION INTO REAR COMPARTMENT. *TT
99092
Service Bulletin/Repair Instructions
CUSTOMER SATISFACTION CAMPAIGN ON VEHICLES EXHIBITNG VARIATIONS IN FRONT SUSPENSION ALIGNMENT THAT CAN RESULT IN VEHICLE PULL EITHER TO THE RIGHT OR TO THE LEFT. *TT
990421004
Service Bulletin/Repair Instructions
SOME PICKUPS AND FULL-SIZE UTILITY MODELS WITH AN AUTOMATIC TRANSFER CASE MAY EXHIBIT A BUMP / CLUNK UPON ACCELERATION. *TT
990730013
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY COMMENT ABOUT THE SERVICE ENGINE SOON LIGHT ILLUMINATING. *TT
660421002
Service Bulletin/Repair Instructions
CUSTOMER MAY COMPLAIN THAT THE 4WD IS INOPERATIVE. *TT
990235001
Service Bulletin/Repair Instructions
CUSTOMERS MAY COMMENT ABOUT A SQUEAK NOISE COMING FROM THE STEERING COLUMN WHILE TURNING THE STEERING WHEEL. *TT
990601003
Service Bulletin/Repair Instructions
CUSTOMER MAY COMMENT ON ENGINE KNOCKING NOISE. *TT
990844002
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY COMMENT THAT THE CD CHANGER WILL NOT RELEASE WHEN DEPRESSING THE EJECT BUTTON. *TT
00773
Service Bulletin/Repair Instructions
4L60E, 4L65E REPLACEMENT VALVE BODY GASKETS DOES NOT SEEM TO FIT. *TT
3001
Service Bulletin/Repair Instructions
THE SERVICE INFORMATION AND OWNERS MANUAL DO NOT SHOW A SERVICE INTERVAL FOR THE 8.6, 9.5, 9.75, 10.5, AND 11.5 INCH REAR AXLES WITH OR WITHOUT G80 (LOCKING DIFFERENTIAL). *TT 2006 ALL GENERAL MOTORS LIGHT DUTY TRUCKS, VANS AND UTILITIES. *TT
3012B
Service Bulletin/Repair Instructions
THE NVG 136 ALL WHEEL DRIVE (AWD) TRANSFER CASE AND THE 236 AND 246 NVG SELECTABLE TRANSFER CASES OPERATING IN THE AUTO MODE MAY EXHIBIT A CONDITION OF A VIBRATION/SHUDDER DURING LOW SPEED TURNS SUCH AS A PARKING LOT MANEUVER, UP TO APPROXIMATELY 5 MPH. *TT 3012A NOT YET RECEIVED. *TT
3300
Service Bulletin/Repair Instructions
4WD MODELS WITH NOISE, VIBRATION ON DRY PAVEMENT. *EH
3349
Service Bulletin/Repair Instructions
4WD INOPERATIVE AND DIAGNOSTIC TROUBLE CODE (DTC) U1026 ATC FUSE OPEN. *TT
3359
Service Bulletin/Repair Instructions
INTERIOR LIGHTS INOPERATIVE AFTER BCM REPLACEMENT B2618 DIAGNOSTIC TROUBLE CODE. *TT
3389
Service Bulletin/Repair Instructions
FOUR WHEEL DRIVE INOPERATIVE AND THE 4WD SERVICE LIGHT WILL ILLUMINATE. DIAGNOSIS MAY REVEAL THAT THE ATC FUSE COULD BE OPEN, POSSIBLE DTC C0308, OR VARIOUS U CODES MAY BE SET. THE ENCODER MOTOR MAY ALSO BE SHORTED OR THE TCCM MAY BE DAMAGED. *TT
3424
Service Bulletin/Repair Instructions
ELECTRONIC TRANSFER CASE UNABLE TO COMPLETE SHIFT. *TT
3526
Service Bulletin/Repair Instructions
INTERMITTENT SERVICE 4WD LIGHT COMES ON WITH DIAGNOSTIC TROUBLE CODE (DTC) C0306 OR C0308 STORED IN TCCM. *TT
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.