Vehicle report

2012 CADILLAC ESCALADE

Service bulletins

1318 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

PIP4902W

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIT3271Q

Service Bulletin/Repair Instructions

This preliminary information communicates information about how to determine if a wheel and tires size change is available.

PIP4902V

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIP6104

Service Bulletin/Repair Instructions

This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical Assistance Case in CX Connect.

PIT6400A

Service Bulletin/Repair Instructions

This PI Communications information on an alternative product dealers can use to perform 19-NA-255: Wax Coating on Frame Peeling, Metal Shows Corrosion/Rusting due to issue with getting product from current supplier listed in the bulletin.

PIP4902U

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIT5214G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer’s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

13598

Other

New Vehicle Monitoring Programs Section in IVH

PIP4902T

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIC5650M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.

PIT6400

Service Bulletin/Repair Instructions

This PI Communications information on an alternative product dealers can use to perform 19-NA-255: Wax Coating on Frame Peeling, Metal Shows Corrosion/Rusting due to issue with getting product from current supplier listed in the bulletin.

PIP4902S

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

25-NA-156

Service Bulletin/Repair Instructions

This service bulletin provides information on Tire Sidewall Irregularities.

00-06-01-026R

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

PIT5074R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.

23-NA-153

Service Bulletin/Repair Instructions

The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

13-02-32-001H

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.

08-03-10-006I

Service Bulletin/Repair Instructions

This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.

15-06-03-001F

Service Bulletin/Repair Instructions

This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.

19-NA-255

Service Bulletin/Repair Instructions

This service bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

25-NA-052

Service Bulletin/Repair Instructions

This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.

PIP5358D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

21-NA-043

Service Bulletin/Repair Instructions

This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.

22-NA-074

Service Bulletin/Repair Instructions

This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

09-06-04-026Z

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

PIT5074Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIT5962B

Service Bulletin/Repair Instructions

This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.

04-06-01-029K

Service Bulletin/Repair Instructions

This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.

PIP4723J

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIP6015

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM technical assistance case using the dealer case management tool.

10-00-89-009F

Service Bulletin/Repair Instructions

This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).

01-06-01-011Q

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

20-NA-132

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.

07-00-89-037T

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

04-06-04-051J

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

23-NA-219

Service Bulletin/Repair Instructions

This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.

20-NA-138

Service Bulletin/Repair Instructions

This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

08-07-30-026I

Service Bulletin/Repair Instructions

This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

18-NA-146

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).

PIT5099H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

02-00-89-002X

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).

PIC5650L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

PIT3271P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

24-NA-174

Service Bulletin/Repair Instructions

The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.

General Communication

Service Campaign

Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.

05-03-08-002J

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.

18-NA-073

Service Bulletin/Repair Instructions

This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

PIT5195H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

01-00-89-010S

Service Bulletin/Repair Instructions

This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

07-06-01-016J

Service Bulletin/Repair Instructions

This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

00-06-01-012N

Service Bulletin/Repair Instructions

This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

05-06-04-022V

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

16-NA-222

Service Bulletin/Repair Instructions

This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.

09-06-04-026Y

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

01-06-01-011P

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

18-NA-306

Service Bulletin/Repair Instructions

This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).

PI0754G

Service Bulletin/Repair Instructions

This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.

16-NA-158

Service Bulletin/Repair Instructions

This service bulletin describes the U.S. Dealer Special Tool Loan Program process.

24-NA-141

Service Bulletin/Repair Instructions

GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.

00-03-10-002M

Service Bulletin/Repair Instructions

This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.

17-NA-157

Service Bulletin/Repair Instructions

This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter.

99-04-20-002O

Service Bulletin/Repair Instructions

This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.

04-06-04-051I

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

16-NA-383

Service Bulletin/Repair Instructions

This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

18-NA-099

Service Bulletin/Repair Instructions

This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.

18-NA-125

Service Bulletin/Repair Instructions

This service bulletin provides information for engine oil life monitor operation calculation.

24-NA-098

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.

20-NA-016

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.

08-07-30-035H

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

16-NA-119

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.

09-00-89-008G

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

06-00-89-029V

Service Bulletin/Repair Instructions

This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

10-08-110-001K

Service Bulletin/Repair Instructions

This service bulletin provides information on proper use of floor mats.

13-08-116-001J

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

15-00-89-004G

Service Bulletin/Repair Instructions

This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

00-03-10-006P

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).

17-NA-052

Service Bulletin/Repair Instructions

This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed.

18-NA-094

Service Bulletin/Repair Instructions

This service bulletin provides information on Takata Air Bag Courtesy Transportation Reimbursement Program - Applicable to GM Recalls listed in bulletin.

10-08-45-001H

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.

23-NA-103

Service Bulletin/Repair Instructions

This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC).

07-00-89-037S

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

11-00-89-005X

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

PIP5596A

Service Bulletin/Repair Instructions

This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.

17-NA-073

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding the field action courtesy transportation policy.

PIT4322P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

19-NA-044

Service Bulletin/Repair Instructions

This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.

16-NA-338

Service Bulletin/Repair Instructions

This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

PI0281K

Service Bulletin/Repair Instructions

This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

02-08-42-001J

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.

PI1394B

Service Bulletin/Repair Instructions

This PI bulletin advises the technician on the proper way to install the pistons in an engine.

PIP5601B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

PI0592I

Service Bulletin/Repair Instructions

This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

23-NA-224

Service Bulletin/Repair Instructions

This bulletin advises the technician that the 6L50 (MYB), 6L80 (MYC) and 6L90 (MYD) Transmission Oil Filter and Seal Kit part number 24236933 is currently transitioning from a kit to the filter (24236517) and seal (24225347) being sold individually.

PIT5074P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIT5962A

Service Bulletin/Repair Instructions

This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.

PIT5214F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

03-00-91-001I

Service Bulletin/Repair Instructions

This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.

20-NA-159

Service Bulletin/Repair Instructions

This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).

05-00-89-029F

Service Bulletin/Repair Instructions

This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.

01-06-01-011O

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

17-NA-170

Service Bulletin/Repair Instructions

This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.

02-00-89-002W

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).

10-00-89-006J

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIT5099G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

07-08-49-020R

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

09-00-89-016H

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.

PIP5628G

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

15-00-89-004F

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

01-00-89-010R

Service Bulletin/Repair Instructions

This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

04-06-04-051H

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

09-06-04-026X

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

17-NA-066

Service Bulletin/Repair Instructions

This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.

PIP5358C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

21-NA-026

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.

99-09-40-005I

Service Bulletin/Repair Instructions

This service bulletin provides information on availability for a seat belt extender.

PIP4902R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

01-06-01-011N

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

99-08-51-001F

Service Bulletin/Repair Instructions

This service bulletin provides information on Paintless Dent Repair Process.

13-08-116-001I

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

PIT4261J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

04-07-30-013E

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.

02-00-89-002V

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

08-07-30-026H

Service Bulletin/Repair Instructions

This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

12-03-10-001E

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

PIC5650K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

11-00-89-005W

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

19-NA-219

Service Bulletin/Repair Instructions

This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.

PIP5628F

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

12-03-10-001D

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

08-07-30-035G

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

10-08-110-001J

Service Bulletin/Repair Instructions

This service bulletin provides information on proper use of floor mats.

11-00-89-005V

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

PI0281J

Service Bulletin/Repair Instructions

This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

00-06-01-012M

Service Bulletin/Repair Instructions

This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

00-06-01-026Q

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

22-NA-009

Service Bulletin/Repair Instructions

This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.

07-06-01-016I

Service Bulletin/Repair Instructions

This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

13-02-32-001G

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.

16-NA-130

Service Bulletin/Repair Instructions

This service bulletin provides information for after installation of a replacement upper valve body, the transmission may have no Reverse and no 2nd gear.

15-NA-017

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.

18-NA-263

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only).

PI0754F

Service Bulletin/Repair Instructions

This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.

99-04-20-002N

Service Bulletin/Repair Instructions

This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.

PIT4322N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

01-08-42-001O

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

PIP5628E

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

00-00-90-002M

Service Bulletin/Repair Instructions

This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.

07-03-16-004E

Service Bulletin/Repair Instructions

This service bulletin provides information for tire pressure monitoring (TPM) system concerns.

02-00-89-002U

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

09-00-89-008F

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

PIP5540J

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

21-NA-124

Service Bulletin/Repair Instructions

This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

PIP5632G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIP4902Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIT3271N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

22-NA-205

Service Bulletin/Repair Instructions

This service bulletin provides information on Module Harvesting.

10-00-89-006I

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIC5453D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

22-NA-185

Service Bulletin/Repair Instructions

This informational bulletin explains how the trans slip or flare can be a normal condition.

22-NA-195

Service Bulletin/Repair Instructions

This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.

PI0592G

Service Bulletin/Repair Instructions

This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

05-06-04-022T

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

06-00-89-031H

Service Bulletin/Repair Instructions

This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.

07-06-01-016H

Service Bulletin/Repair Instructions

This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

13-08-116-001H

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

15-00-89-004E

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

01-00-89-010Q

Service Bulletin/Repair Instructions

This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

05-00-89-072F

Service Bulletin/Repair Instructions

This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.

09-06-04-026W

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

00-06-01-012L

Service Bulletin/Repair Instructions

This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

01-06-01-011M

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

04-06-04-051G

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

00-06-01-026P

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

11-00-89-005U

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

05-00-89-029E

Service Bulletin/Repair Instructions

This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.

22-NA-181

Service Bulletin/Repair Instructions

This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.

PIP5640A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

11-00-89-005T

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

20-NA-065

Service Bulletin/Repair Instructions

This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

PIT4261H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

PIC5260F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIT5099F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

16-NA-109

Service Bulletin/Repair Instructions

This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.

PIP5358B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

PIP5856

Service Bulletin/Repair Instructions

This Preliminary information communicates provides information to the technician on the use of R-99 or R-95  Renewable diesel fuel.

12-00-89-003B

Service Bulletin/Repair Instructions

This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).

PIC5260E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

01-00-89-010P

Service Bulletin/Repair Instructions

This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

PI0281I

Service Bulletin/Repair Instructions

This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

01-00-89-010O

Service Bulletin/Repair Instructions

This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

04-06-04-051F

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

05-00-89-072E

Service Bulletin/Repair Instructions

This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.

PIT3271M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIT3271L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

080089014G

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

PIP5276G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides steps the technician will uses to diagnose and repair vehicles that have low oil pressure after an oil change with the engine Regular Production Option Code L20, L77, L94, L96, L99, L9H, LC8, LC9, LH9, LMF, LMG, LY6, or LZ1. Vehicle may have Service Engine Soon lamp with Diagnostic Trouble Code P0521 or Low Oil Pressure message on the instrument panel. Dealer will need to determine if bulletin 10-06-01-008 was completed. If the bulletin was performed inspect the left rocker cover. Dealer will insure the left rocker can hold water without leaking. If leaks are found apply room temperature vulcanization silicone to the rocker cover if possible or replace the left rocker cover.

070601016G

Service Bulletin/Repair Instructions

This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

150089004D

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

PI0653F

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.

PIT4322M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

PIP4902P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIP4723F

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIP5632F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

22NA009

Service Bulletin/Repair Instructions

This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.

070316004D

Service Bulletin/Repair Instructions

This service bulletin provides information for tire pressure monitoring (TPM) system concerns.

16NA222

Service Bulletin/Repair Instructions

This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.

000090002L

Service Bulletin/Repair Instructions

This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.

050604022S

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

1308116001G

Service Bulletin/Repair Instructions

The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

030310007K

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires.

030091001H

Service Bulletin/Repair Instructions

This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.

PIT3099U

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

17NA308

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of carpet damage, seat mounting stud wear through, hole in second row (Intermediate) carpet.

PIC5650J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

21NA152

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint percentage.

010842001N

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

PIT4261G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

990420002L

Service Bulletin/Repair Instructions

This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.

PIP5632E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

080730035E

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

070089037Q

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

21NA124

Service Bulletin/Repair Instructions

This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

PIT5403H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

18NA306

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).

070089037P

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

100089006H

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIT4322L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

PIP5358A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

PIT5214E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

20NA159

Service Bulletin/Repair Instructions

This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).

N202307080 01

Service Bulletin/Repair Instructions

Service Update Bulletin (Labor Codes Added). Certain vehicles may have a condition where the engine control module (ECM) software allows the Auto Stop to occur at a state of charge below 65%. Auto Stop is supposed to be inhibited at 65% to protect against excessive battery wear and discharge. Dealers are to reprogram the ECM.

19NA044

Service Bulletin/Repair Instructions

This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.

16NA338

Service Bulletin/Repair Instructions

This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

21NA103

Service Bulletin/Repair Instructions

This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition.

000601026N

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

050308002I

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.

18NA146

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).

020089002T

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

18NA099

Service Bulletin/Repair Instructions

This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.

PIP5163E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIC5260D

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIP5540G

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PIP5725A

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use.  Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement.  This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.

110089005Q

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

1008110001I

Service Bulletin/Repair Instructions

This informational bulletin provides information on proper use of floor mats.

20NA138

Service Bulletin/Repair Instructions

This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

19NA255

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

21NA043

Service Bulletin/Repair Instructions

This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.

16NA109

Service Bulletin/Repair Instructions

This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.

150089004C

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

21NA026

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.

010601011L

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

090604026S

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

18NA263

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).

060089031F

Service Bulletin/Repair Instructions

This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.

PIT5074N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

000310002L

Service Bulletin/Repair Instructions

This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.

PIT3271K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

990851001E

Service Bulletin/Repair Instructions

Thins informational bulletin provides information on Paint-less Dent Repair Process.

PI0754D

Service Bulletin/Repair Instructions

This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.

20NA213

Service Bulletin/Repair Instructions

This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and PF48.

1308116001F

Service Bulletin/Repair Instructions

The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

PIP5684C

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.

050604022R

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

PIP5628C

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

110089005P

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

PIP5226D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

PIT5099E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIC5650H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

20NA026

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of Loss of Radio Audio Shortly After an OnStar In-Vehicle Voice Message Is Heard.

PIP5684B

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.

PIP4902N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

120232002B

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to eliminate a power steering noise due to extremely low temperatures.

PIC5453C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

110089005O

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

060089029T

Service Bulletin/Repair Instructions

This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

PIP5628B

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

070849020Q

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

16NA383

Service Bulletin/Repair Instructions

This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

PIP5725

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use.  Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement.  This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.

030089006R

Service Bulletin/Repair Instructions

This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.

060089029S

Service Bulletin/Repair Instructions

This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

PIP5684A

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.

000310003Z

Service Bulletin/Repair Instructions

This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).

060089029R

Service Bulletin/Repair Instructions

This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

PIC5650G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

PI0281H

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

PIT4322K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

060089029Q

Service Bulletin/Repair Instructions

This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.

100089005I

Service Bulletin/Repair Instructions

This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.

060089029P

Service Bulletin/Repair Instructions

This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.

070089037O

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance programs.

PIT4261F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

PIT5403F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

020089002S

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

050310020G

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.

040601029J

Service Bulletin/Repair Instructions

This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules.

19NA219

Service Bulletin/Repair Instructions

This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.

000310003Y

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

16NA119

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.

PIT3099T

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

PIP4723D

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

050307009I

Service Bulletin/Repair Instructions

This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.

20NA016

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.

PIP5540F

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PI0592F

Service Bulletin/Repair Instructions

This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

100089009D

Service Bulletin/Repair Instructions

This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.

080089014F

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

010842001M

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.

080310006G

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.

PIT3271J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIT5074M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

DOR-G9Z8V-12

Service Bulletin/Repair Instructions

This SKU is a Fuel Pump Driver Module. The customer communication requested return of unsold inventory to inspect the software. The software may have a fault where the readiness monitors are stuck in the not-ready or incomplete position. The readiness monitors will not cause performance or emissions issues but will prevent the emissions scanning tools from confirming the module is performing correctly, causing the vehicle to fail state required emissions tests.

990420002K

Service Bulletin/Repair Instructions

This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.

PIP5684

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.

100089006G

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).

PIP5540E

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PIP5601A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

010601011K

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

100089009C

Service Bulletin/Repair Instructions

This informational bulletin provides information on key code security and information on GM key code look up applications.

010089010N

Service Bulletin/Repair Instructions

This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).

17NA073

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding the field action courtesy transportation policy.

150844001J

Service Bulletin/Repair Instructions

This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.

PIP5632B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIT3099S

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

PI0592E

Service Bulletin/Repair Instructions

This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961).

090604026R

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

130089008B

Service Bulletin/Repair Instructions

This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC.

000601026M

Service Bulletin/Repair Instructions

This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

070601016F

Service Bulletin/Repair Instructions

This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

080730026F

Service Bulletin/Repair Instructions

This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

PIP4158H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.

990089019R

Service Bulletin/Repair Instructions

This informational bulletin provides process information for the (GWM) and (WPC) parts return program.

PI1344C

Service Bulletin/Repair Instructions

This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.

PIT3099R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.

050604022Q

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

100845001G

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.

130232001F

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.

1308116001E

Service Bulletin/Repair Instructions

The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

000601012J

Service Bulletin/Repair Instructions

This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

090604026Q

Service Bulletin/Repair Instructions

This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

PI0430C

Service Bulletin/Repair Instructions

This preliminary information bulletin provides a procedure for suspension connector diagnosis and replacement due to the magnetically controlled suspension electrical connector not seated.

060847001O

Service Bulletin/Repair Instructions

This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.

PIT5074L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIP5632A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

080730035D

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

PIT5049E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.

PIT3219F

Service Bulletin/Repair Instructions

This Preliminary Information communicates to technicians that the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49).   These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.

000310006N

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).

PIP5640

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

PIP5226C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

080089014E

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

PIC5260C

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

030729004L

Service Bulletin/Repair Instructions

This informational bulletin provides normal operating characteristics and diagnostic information on Manual transmissions.

1008110001H

Service Bulletin/Repair Instructions

This informational bulletin provides information on proper use of floor mats.

110089005N

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.

030089006Q

Service Bulletin/Repair Instructions

This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.

060089029O

Service Bulletin/Repair Instructions

This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.

040089053G

Service Bulletin/Repair Instructions

This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.

070849020P

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

1008110001G

Service Bulletin/Repair Instructions

This informational bulletin provides information on proper use of floor mats.

PIT4585F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that the Serial Data Gateway Module (SDGM) may report "Crash Sense Failed" and the 300v Hybrid Battery Contactors will remain open until the Hybrid Powertrain Control Module's (HPCM) High Voltage (HV) DTCs are reset. And How to Reset.

PIP4902M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

100845001F

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".

090089002Q

Service Bulletin/Repair Instructions

This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.

PIP5632

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIP4902L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

050604022P

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

PIP3119P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster  Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.

120089002C

Service Bulletin/Repair Instructions

This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.

PIP5540D

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PIP5628

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

PI0564K

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

PIP5627

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer an issue where the vehicle's inspection and maintenance monitors along with diagnostic trouble codes may reset unprompted due to the installation of an aftermarket fuel pump control module.

070845001H

Service Bulletin/Repair Instructions

This informational bulletin provides information for aftermarket trailer brake controller added to their vehicle, OR in lieu of the factory integrated trailer brake controller (ITBC) (RPO JL1).

090089016F

Service Bulletin/Repair Instructions

This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.

090089002P

Service Bulletin/Repair Instructions

This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.

010089010M

Service Bulletin/Repair Instructions

This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).

080089014D

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

17NA346

Service Bulletin/Repair Instructions

This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs.

17NA170

Service Bulletin/Repair Instructions

This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.

100089005H

Service Bulletin/Repair Instructions

This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.

040089015T

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on required operating procedures.

060089026O

Service Bulletin/Repair Instructions

This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).

PIT5214D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

17NA066

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow test.

010842001L

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.

080089014C

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

PIT4614C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides steps the technician will take to repair a no crank/no start concern with a diagnostic trouble code of B009F in the Serial Data Gateway Module equipped with Regular Production Option code HP2. The vehicle may exhibit a no crank or no start, or a Service Hybrid message with no codes. The technician will inspect the High Voltage Circuit Impact Detection sensor for water intrusion or corrosion at the weather pack. Inspect the High Voltage  Circuit Impact Detection sensor for cracks or terminal corrosion and replace the sensor or terminals along with the weather pack seals if damage is found. If there is no damage found the technician will leave the sensor unplugged and power up the vehicle to induce a code, then power down the vehicle with the Tech 2 unplugged from the vehicle for two minutes. Clear the code and recheck for the message and codes, if the code resets the technician will replace the High Voltage Circuit Impact Detection sensor and terminals with terminated leads. Technician is to repeat the above steps to verify the concern is corrected.

PIT4811C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with the steps on how to diagnose vehicles with a no crank with multiple Diagnostic Trouble Codes set in several different modules with Regular Production Option Code HP2. Technician will retrieve all the Diagnostic Trouble Codes that are set current in the vehicle. When there are multiple Diagnostic Trouble Codes technician may wonder were to start the diagnose process. Technician will address Diagnostic Trouble Codes P1AE2-P1AE4, P1B05, or P1B06 first as they're related to the High Voltage System Interlock Circuit for the high voltage system. Second Diagnostic Trouble Codes to address will be any loss of communication Diagnostic Trouble Codes related to the Powertrain expansion bus or the high speed LAN bus. Then address any low voltage concerns that may be related to a low 12 volt battery.

PIP5540B

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

000310003X

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

060847001N

Service Bulletin/Repair Instructions

This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.

060850009J

Service Bulletin/Repair Instructions

This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.

PIP4925B

Service Bulletin/Repair Instructions

This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.

PIT5353C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

PIT3946C

Service Bulletin/Repair Instructions

This Preliminary Information communicates an issues with the headliner sagging and how to reattach the velcro using Hardman Double Bubble Epoxy part number 04001.

PIP5601

Service Bulletin/Repair Instructions

This Preliminary information communicates

PIP4138R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

PIT5099D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIP5596

Service Bulletin/Repair Instructions

This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.

PIT4322J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

PIT5403E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

PIP4902K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIP5163D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIP4681E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a random bump, chuggle, or fishbite sensation when crowding the throttle slightly with the Torque Converter Clutch on while cruising at 35-60 miles per hour. Technician should follow all published Service Information diagnostics if the concern is repaired compare to a like vehicle with the same options.

PIP3366C

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer technician thatLight Duty Trucks equipped with automatic transmissions and 4 wheel drive may exhibit a condition of grinding/ratcheting type noise when shifting the automatic transmission into park while the transfer case is in 4 wheel drive low (4LO) range. Dealers technician's are advised this condition should be deemed a normal characteristic of 4WD low operation.

PIC5260B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIT5099C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIC5953D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

PIT5399A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

PIT3219E

Service Bulletin/Repair Instructions

This Preliminary Information communicates to techniciansthat the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49). These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.

1208132001E

Service Bulletin/Repair Instructions

This informational bulletin explains to the dealer how to cover a possible customers mistake when a fuse has been blown.

18NA125

Service Bulletin/Repair Instructions

This informational bulletin provides information for engine oil life monitor operation calculation.

PI0754C

Service Bulletin/Repair Instructions

This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal characteristic.

080730035C

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

PI0281G

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

PI0564J

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

130089010B

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program.

060089031E

Service Bulletin/Repair Instructions

This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.

PIT5195D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

000089027J

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on properly eliminating unwanted odors in vehicles.

110089002C

Service Bulletin/Repair Instructions

This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).

030089006P

Service Bulletin/Repair Instructions

This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.

PIT4376J

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician about key and theft information for Fleet Vehicles equipped with RPO 6E2 or 6E8 and converting to fleet mode. Technician will need to ensure fleet vehicles with RPO 6E2 or 6E8 should be checked to verify that the Theft Deterrent Module is in fleet mode prior to attempting to add keys.

17NA215

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar® Module Functionality After OnStar Module Replacement for Another Condition.

090604015C

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.

090604026N

Service Bulletin/Repair Instructions

This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada

110089005L

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.

PIT5049D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.

030603004W

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

060601010D

Service Bulletin/Repair Instructions

This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.

150603001D

Service Bulletin/Repair Instructions

This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.

PIP5226B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

PIP4138Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

PIT3271H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIP5540A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

100864002D

Service Bulletin/Repair Instructions

This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.

050851001I

Service Bulletin/Repair Instructions

This information bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.

PI0653E

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.

PIP3343F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.

060089026N

Service Bulletin/Repair Instructions

This warranty bulletin provides labor operation numbers for customer concerns that cant be duplicated.

010310003P

Service Bulletin/Repair Instructions

This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.

PIP5540

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.

050604022O

Service Bulletin/Repair Instructions

This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.

PIC5491K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

PIP4578B

Service Bulletin/Repair Instructions

This PI was superseded to update model years and add information concerning idle surge, reduced engine power mode, and/or DTCs P0068, P0121, P1516, P2101, P2119, and/or P2176 that may be experienced on high mileage vehicles. Please discard PIP4578.

040089015R

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on required operating procedures.

16NA075

Service Bulletin/Repair Instructions

This Bulletin provides procedures to correct a condition of Power Foldaway Mirror Glass Shake, Flutter at Normal Driving Speeds

000310003W

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

080730026E

Service Bulletin/Repair Instructions

This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

070089037L

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.

130232001E

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.

120089007A

Service Bulletin/Repair Instructions

This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.

150603001C

Service Bulletin/Repair Instructions

This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.

070089036I

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on enhancing field product reports with digital pictures.

010601011J

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

16NA356

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.

040730013D

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.

16NA158

Service Bulletin/Repair Instructions

This bulletin describes the Dealer special tool loan program process.

15NA082

Service Bulletin/Repair Instructions

This technical bulletin provides repair information for installing a new stabilizer shaft bracket to correct a customer concern of on a clunking noise originating from the front of the vehicle that is more predominant during turns or traveling over bumps.

PIT4261E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

PIT4730B

Service Bulletin/Repair Instructions

This Preliminary Information communication a diagnostic tip if the high speed lan bus is shorted to ground, which can cause the BCM to appear off line.

070604019F

Service Bulletin/Repair Instructions

This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.

PIC3100F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

PIT3946B

Service Bulletin/Repair Instructions

This Preliminary Information communicates an issues with the headliner sagging and how to reattachthe velcrousing Hardman Double Bubble Epoxy part number 04001.

PIC5492F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.

PIT5353B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

070849020M

Service Bulletin/Repair Instructions

IPC Odometer Programming Method Quick Reference Guide

150089004B

Service Bulletin/Repair Instructions

Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component

150089005A

Service Bulletin/Repair Instructions

Essential Tools that Include Consumable Parts (U.S. Only)

PIT5236K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.

030603004V

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

PIP4723C

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIT5074K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIT5403D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

PIT4322H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

040601029I

Service Bulletin/Repair Instructions

This informational bulletin explains the importance of maintaining the vehicle.

100089005G

Service Bulletin/Repair Instructions

This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.

000601012H

Service Bulletin/Repair Instructions

This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

PIT5389E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

PIT3099Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.

070601016D

Service Bulletin/Repair Instructions

This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

00-06-01-026J

Service Bulletin/Repair Instructions

This informational bulletin provides information on Intake Manifold Inspection/Replacement After Severe Internal Engine Damage.

13-08-116-001C

Service Bulletin/Repair Instructions

The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

17-NA-274

Service Bulletin/Repair Instructions

This informational bulletin provides a option for the customer to replace the hot/cold cup holder with a standard cup holder.

99-08-51-001D

Service Bulletin/Repair Instructions

Thins informational bulletin provides information on Paint-less Dent Repair Process.

PIP5163C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIC5932B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.

04-00-89-015Q

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on required operating procedures.

08-08-44-029H

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.

04-00-89-015P

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on required operating procedures.

17-NA-244

Service Bulletin/Repair Instructions

This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.

03-03-10-007J

Service Bulletin/Repair Instructions

This informational bulletin provides information on the temporary tire flat spotting condition.

04-00-89-015L

Service Bulletin/Repair Instructions

This informational bulletin provides warranty policy information on required operating procedures.

10-00-89-005F

Service Bulletin/Repair Instructions

This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information.

PI0564I

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

PIC5611E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.

PIT5564A

Service Bulletin/Repair Instructions

This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set.

PIC5588D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

PIT3099P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

00-03-10-002K

Service Bulletin/Repair Instructions

This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.

05-00-89-029D

Service Bulletin/Repair Instructions

This informational bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.

PI0020E

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides technicians with information on the normal condition of white, milky or cloudy appearance of front differential fluid.

03-00-89-006N

Service Bulletin/Repair Instructions

This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.

04-00-89-015O

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on required operating procedures.

11-00-89-005K

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.

17-NA-126

Service Bulletin/Repair Instructions

This informational bulletin provides information on Non-Design Intent Wheel Lock Nuts and Lug Nuts.

PI0281F

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

10-08-110-001F

Service Bulletin/Repair Instructions

This informational bulletin provides information on proper use of floor mats.

03-06-03-004U

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

99-04-20-002J

Service Bulletin/Repair Instructions

This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.

PIP4112R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

15-08-44-001I

Service Bulletin/Repair Instructions

This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.

15-08-73-001A

Service Bulletin/Repair Instructions

This informational bulletin explains how to update the older Onstar module software to new software over GSA.

PI0671A

Service Bulletin/Repair Instructions

This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid reservoir.

17-NA-067

Service Bulletin/Repair Instructions

This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.

06-08-47-001M

Service Bulletin/Repair Instructions

This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.

PIP4600F

Service Bulletin/Repair Instructions

This Preliminary Information communication to the dealer technicians that the Technical Assistance Center 2ML70 (Two-Mode Hybrid)Part Restrictionhas ended.

10-00-89-006F

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers how to submit a product information report.

PIT5389C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

07-07-30-010D

Service Bulletin/Repair Instructions

This informational bulletin provides explanation on how to take snapshot data with a Tech 2 and upload it to a computer and where to email the info to.

PIC4935F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.

PIP4723B

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

GCUS-3-848

Service Bulletin/Repair Instructions

44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.

PIC3278G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

PIC4801H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.

PIC5959C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.

PIC5588C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

02-00-89-002Q

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.

01-03-10-003O

Service Bulletin/Repair Instructions

This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.

PIP5029H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.

PIP5338A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.

PIT5049C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.

PIP4902J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

08-03-10-006F

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)

03-08-46-004S

Service Bulletin/Repair Instructions

This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.

PIC5759B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.

PIP3119N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster  Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.

PIT4733K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.

99-00-89-019O

Service Bulletin/Repair Instructions

This informational bulletin provides information for the (GWM) and (WPC) on parts return program.

PIT5236J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to ensure campaigns 14395 or 15086 are completed. Technician will need to use Global Diagnostic System 2 and gather information and contact General Motors Technical Assistance Center for further assistance.

07-08-49-020L

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

PIT4163F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that only have audio from the front left speaker after replacing the amplifier. Technician should program the amplifier using Tis-2-Web using Service Programming System with the latest calibrations.

PIP4138P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

08-08-44-015H

Service Bulletin/Repair Instructions

This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs

99-00-89-019N

Service Bulletin/Repair Instructions

This informational bulletin provides information for the (GWM) and (WPC) on parts return program.

PIC5492E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.

01-03-10-003N

Service Bulletin/Repair Instructions

This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.

05-03-08-002H

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.

02-00-89-002P

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.

05-00-89-055F

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill procedures.

PIT4808L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may stall and have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Code P0BBD. Technician will need to replace the battery and update the Battery Energy Storage Control Module using TIS2Web.

PIT3099N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

08-09-41-002H

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to complete a terminal replacement or connector re connection to correct a condition of Diagnostic Information for Supplemental Inflatable Restraint (SIR) System, Intermittent AIR BAG Indicator/Lamp Illuminated with DTC(s) B0012, B0013, B0015, B0016, B0019, B0020, B0022, B0023, B0026, B0033, B0040, B0042 or B0044 Set (Inspect and Replace Connector Position Assurance (CPA) Retainer)

PIP5163B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

11-00-89-004B

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on the change in product field action customer reimbursement procedure.

06-08-64-001D

Service Bulletin/Repair Instructions

This Informational bulletin describes warranty part reviews where door glass had chips or scratches.

01-03-10-003M

Service Bulletin/Repair Instructions

This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.

00-03-10-003V

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

PIT5389B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.

04-06-04-051E

Service Bulletin/Repair Instructions

This informational bulletin provides information for maintenance cleaning of the fuel injectors.

04-06-04-051D

Service Bulletin/Repair Instructions

This informational bulletin provides information for maintenance cleaning of the fuel injectors.

PIT5179A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have Brake Pedal Position and or Cruise Brake Pedal parameters are showing "Applied" with the brake pedal released. Technician will need to inspect for any opens/high resistance or terminal issue in circuit 6311.

040604051D

Service Bulletin/Repair Instructions

This informational bulletin provides information for maintenance cleaning of the fuel injectors.

PIT5236H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.

030603004S

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

030603004T

Service Bulletin/Repair Instructions

Battery Testing and Warranty Replacement Requirements (North America ONLY)

040089015N

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on required operating procedures.

080730026D

Service Bulletin/Repair Instructions

This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

050604022N

Service Bulletin/Repair Instructions

This informational bulletin provides information on the top tier fuels that are recommended in GM vehicles.

090089002N

Service Bulletin/Repair Instructions

This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.

100844006D

Service Bulletin/Repair Instructions

This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc information.

00-03-10-003U

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

05-08-44-024E

Service Bulletin/Repair Instructions

This informational bulletin provides information on return or reimbursement of customer owned CDs, DVDs or Navigation Discs .

07-00-89-037J

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.

08-08-44-029G

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.

09-00-89-008C

Service Bulletin/Repair Instructions

This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

PIP5282A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ABOUT THE CALCULATION AND OPERATION OF THE ENGINE OIL LIFE MONITOR. THE MONITOR CALCULATES THE PERCENT OF OIL LIFE REMAINING, BASED ON 3 PATHWAYS. THE FIRST PATHWAY FOR OIL LIFE CALCULATION IS ENGINE REVOLUTIONS. THE SECOND PATHWAY FOR OIL LIFE CALCULATION IS THE MILEAGE FORM THE LAST REST FOR ALL GENERAL MOTORS POWERTRAINS EXCEPT THE VOLT. THE THIRD PATHWAY FOR OIL LIFE CALCULATION IS THE AMOUNT OF TIME THE OIL IS IN THE ENGINE. THE VOLT USES A 2 YEAR TIMER INSTEAD OF 1 YEAR. IT ALSO USES THE ENGINE REVOLUTION COUNTER. IT DOES NOT USE THE MILEAGE PATHWAY TO COUNT DOWN.

09-00-89-016E

Service Bulletin/Repair Instructions

This warranty nonadministrative bulletin provides information on the proper use of the labor op 0600014.

11-00-89-005J

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Goodwill Tools, Customer Enthusiasm, and Policy Guidelines.

02-08-98-002G

Service Bulletin/Repair Instructions

This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done.

08-08-44-015G

Service Bulletin/Repair Instructions

This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs

PIT4383Q

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE ELECTRONIC BRAKE CONTROL MODULE AND BRAKE PRESSURE MODULATOR VALVE FOR THE 2-MODE HYBRID UTILITIES AND TRUCKS ARE NOW OFF RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER.

PIT5206E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS ON DIAGNOSING AND REPAIRING VEHICLES THAT MAY HAVE UNWANTED GRADE BRAKING, REDUCED ENGINE POWER WITH NO DRIVER INFORMATION CENTER MESSAGES “ BRAKE PEDAL OVERRIDE FEATURE “, TRANSMISSION BUSY OR FREQUENT SHIFTING UP OR DOWN, AND DIAGNOSTIC TROUBLE CODES P057B, P057C, AND/OR P057D MAY OR MAY NOT BE SET. TECHNICIAN WILL USE THIS PRELIMINARY INFORMATION TO FIND THE BRAKE PEDAL POSITION DATA PARAMETERS IN THE SCAN TOOL, AND ALSO TO PROVIDE SOME ADDITIONAL DIAGNOSTIC HELP. THESE ISSUES MAY BE CAUSED BY AN INCORRECT BRAKE PEDAL POSITION SENSOR INPUT TO THE ENGINE CONTROL MODULE. TECHNICIAN WILL VERIFY WITH THE SCAN TOOL IF THE ENGINE CONTROL MODULE HAS THE CORRECT PARAMETERS FOR THE BRAKE PEDAL POSITION SENSOR. IF AN ENGINE CONTROL MODULE BRAKE PEDAL POSITION SENSOR RELEARN IS PERFORMED, THE TRUCK MAY BE TEMPORARILY REPAIRED UNTIL THE INTERMITTENT WIRING ISSUE BETWEEN THE ENGINE CONTROL MODULE AND BRAKE PEDAL POSITION SENSOR OCCURS AGAIN. ON 2014 AND NEWER TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X115 AND X119. ON THE 2014 AND PREVIOUS TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X205.

01-00-89-010L

Service Bulletin/Repair Instructions

This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).

07-08-49-020K

Service Bulletin/Repair Instructions

This informational bulletin explains the programming method quick reference guide for the IPC Odometer.

01-03-10-003L

Service Bulletin/Repair Instructions

This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage) and for vehicles within this warranty period, the defective tires will be replaced on a pro rata adjustment basis. It also provides GWM Transaction information.

PI0639D

Service Bulletin/Repair Instructions

This preliminary bulletin provides a procedure to install adhesive back stock to the electrical connector for the steering wheel position sensor, to eleminate the excessive clearance/movement that causes the connector to loose contact and turns the Service Stabilitrak message on.

PIC5491J

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.

PIP5029G

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.

05-00-89-072D

Service Bulletin/Repair Instructions

This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information.

16NA241

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.

PIP4833F

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE PART RESTRICTION FOR THE AUXILIARY TRANSMISSION FLUID PUMP CONTROL MODULE AND PUMP PART NUMBERS 24261817AND 19207983 HAS ENDED.

PIT4821E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HIGH VOLTAGE BATTERY FOR THE 2-MODE IS NO LONGER ON PART RESTRICTION.

PIT5074J

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL

PI1394A

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.

16NA260

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.

PIT5403B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS TO DIAGNOSIS AND REPAIR VEHICLES WITH VARIOUS HANDLING, VEHICLE DYNAMICS CONCERNS, NOISES FROM THE SUSPENSION OR UNDERBODY, OR ISSUES RELATED TO DAMAGED SUSPENSION COMPONENTS. BEFORE ANY IN-DEPTH DIAGNOSTICS ARE PERFORMED, BE AWARE THAT VARIOUS ISSUES COULD OCCUR IF THE VEHICLE HAS BEEN MODIFIED AND INFORM THE CUSTOMER THE CONDITIONS NOTED MAY NOT BE COVERED UNDER WARRANTY. TECHNICIAN WILL INSPECT FOR INSTALLED AFTERMARKET SUSPENSION COMPONENTS. ALSO INSPECT FOR IMPROPERLY ADJUSTED TORSION BARS.

PI0388F

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.

PIP4786C

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.

030603004R

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.

16NA249

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS LESS THAN 10,000 MILES ON IT.

070898001B

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF “CLIPPING” TO REPAIR COLLISION DAMAGE TO VEHICLES. GM HAS NOT TESTED OR VALIDATED A “CLIPPED VEHICLE” REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.

000601012F

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.

030604017I

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.

110849001S

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.

000601026I

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE.

00-06-01-026H

Service Bulletin/Repair Instructions

This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.

16-NA-223

Service Bulletin/Repair Instructions

This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Or, they may come in for ABS or general handling/braking concerns.

07-03-10-008E

Service Bulletin/Repair Instructions

THIS INFORMATIONAL PROVIDES INFORMATION ON SLIGHT OR MILD TIRE FEATHERING AND RECOMMENDED PRACTICES.

PIP5094A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.

10-08-110-001E

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PROPER USE OF FLOOR MATS.

PIT4614B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES STEPS THE TECHNICIAN WILL TAKE TO REPAIR A NO CRANK/NO START CONCERN WITH A DIAGNOSTIC TROUBLE CODE OF B009F IN THE SERIAL DATA GATEWAY MODULE EQUIPPED WITH REGULAR PRODUCTION OPTION CODE HP2. THE VEHICLE MAY EXHIBIT A NO CRANK OR NO START, OR A SERVICE HYBRID MESSAGE WITH NO CODES. THE TECHNICIAN WILL INSPECT THE HIGH VOLTAGE CIRCUIT IMPACT DETECTION SENSOR FOR WATER INTRUSION OR CORROSION AT THE WEATHER PACK. INSPECT THE HIGH VOLTAGE CIRCUIT IMPACT DETECTION SENSOR FOR CRACKS OR TERMINAL CORROSION AND REPLACE THE SENSOR OR TERMINALS ALONG WITH THE WEATHER PACK SEALS IF DAMAGE IS FOUND. IF THERE IS NO DAMAGE FOUND THE TECHNICIAN WILL LEAVE THE SENSOR UNPLUGGED AND POWER UP THE VEHICLE TO INDUCE A CODE, THEN POWER DOWN THE VEHICLE WITH THE TECH 2 UNPLUGGED FROM THE VEHICLE FOR TWO MINUTES. CLEAR THE CODE AND RECHECK FOR THE MESSAGE AND CODES, IF THE CODE RESETS THE TECHNICIAN WILL REPLACE THE HIGH VOLTAGE CIRCUIT IMPACT DETECTION SENSOR AND TERMINALS WITH TERMINATED LEADS. TECHNICIAN IS TO REPEAT THE ABOVE STEPS TO VERIFY THE CONCERN IS CORRECTED.

04-00-89-015M

Service Bulletin/Repair Instructions

THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES POLICY INFORMATION ON USING GM SERVICE POLICIES AND PROCEDURE MANUAL THAT REPRESENT KEY GM REQUIREMENTS FOR SERVICE OPERATIONS.

PIT4539U

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE DRIVE MOTOR GENERATOR CONTROL MODULE PART RESTRICTION HAS END.

09-06-04-026M

Service Bulletin/Repair Instructions

This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2.

99-08-51-007G

Service Bulletin/Repair Instructions

This informational bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening or re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed.

16-NA-171

Service Bulletin/Repair Instructions

This informational bulletin provides repair information on reconnection of rear window (defroster) contact or tab.

PI0592D

Service Bulletin/Repair Instructions

This informational bulletin provides information on service programming system (SPS) errors.

12-08-132-001D

Service Bulletin/Repair Instructions

This informational bulletin provides warranty information on accessory power outlet and trailer lighting fuse replacement.

PIP-3140-G

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT A NOISE OR A VIBRATION IN THE VEHICLE THAT SEEMS TO BE ABNORMAL MAY NOT HAVE BEEN THERE WHEN THE VEHICLE WAS PURCHASED. TECHNICIAN SHOULD LOOK FOR NON - GENERAL MOTORS AFTERMARKET ACCESSORIES INSTALLED ON THE VEHICLE THAT CAN CAUSE THESE ISSUES.

PIT-4383-P

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE ELECTRONIC BRAKE CONTROL MODULE AND BRAKE PRESSURE MODULATOR VALVE FOR THE 2-MODE HYBRID UTILITIES AND TRUCKS ARE BEING PLACED ON PARTS ORDERING RESTRICTION THROUGH THE GM TECHNICAL ASSISTANCE CENTER (TAC).

SB-02-07-30-029Z

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE PRODUCT QUALITY CENTER (PQC) ASSEMBLY REPLACEMENT PROCESS.

SB-16-NA-130

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO INSPECT THE UPPER VALVE BODY TO DETERMINE THE CORRECT RPO USAGE TO CORRECT A CONCERN THAT AFTER INSTALLATION OF A REPLACEMENT UPPER VALVE BODY, THE TRANSMISSION MAY HAVE NO REVERSE AND NO 2ND GEAR DUE TO THE INSTALLATION OF THE INCORRECT UPPER VALVE BODY.

SB-16NA-131

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON VEHICLES DESIGNED TO OPERATE ON GASEOUS FUELS.

PIC-5374-D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.

PIC5374D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.

PIT5485B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

PIP5168E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN, AND THE STEPS TO REPAIR THE CONCERN OF THE VEHICLE CRANKS BUT DOES NOT START. THE TECHNICIAN IS TO INSPECT FOR A SHEARED CAM PIN IN THE ENGINE.

PIC4707E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.

PIC5088F

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.

SB-10-08-46-001C

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CONTACT ONSTAR FOR HARD MUTE REQUEST TO CORRECT A CUSTOMER CONCERN WHEN THE RADIO IS ON, IT DOES NOT MUTE ENOUGH WHEN THE ONSTAR® TURN-BY-TURN NAVIGATION DIRECTIONS ARE ANNOUNCED DUE TO CUSTOMER IMPROPERLY SETTING THE RADIO VOLUME HIGH ENOUGH WHEN THE TURN-BY-TURN NAVIGATION MESSAGES ARE PLAYED.

SB-15-06-03-001B

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE USEFUL ON DIAGNOSING BATTERIES THAT HAVE SET FOR A LONG PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES.

PIC-4935-E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

PIC4935E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

PIT5389A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.

SB-03-06-03-004Q

Service Bulletin/Repair Instructions

THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY.

SB-06-08-47-001L

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES WARRANTY INFORMATION ON USING THE SERVICE PROGRAMMING SYSTEM (SPS) FOR PROGRAMMING CONTROL MODULES

SB-07-06-01-016C

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION INTERNAL ENGINE NOISE OR DAMAGE AFTER OIL FILTER REPLACEMENT

SB-16-NA-119

Service Bulletin/Repair Instructions

THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON GM’S POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA.

PI-0754-B

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT.

SB-16-NA-117

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PURPOSE OF MAGNETIC DRAIN PLUGS.

PIT5485A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

PI-0281-E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS.

PIT-4539-T

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION ON THE DRIVE MOTOR GENERATOR CONTROL MODULE PART RESTRICTION. DEALER WILL NEED TO CALL GM TECHNICAL ASSISTANCE CENTER FOR FURTHER INSTRUCTIONS.

PIT4539T

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION ON THE DRIVE MOTOR GENERATOR CONTROL MODULE PART RESTRICTION. DEALER WILL NEED TO CALL GM TECHNICAL ASSISTANCE CENTER FOR FURTHER INSTRUCTIONS.

PIC-5260-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.

PIC5260A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.

SB-03-07-29-004K

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE OPERATING CHARACTERISTICS OF A MANUAL TRANSMISSION.

SB-16-NA-109

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT THE STEERING GEAR FOR A NORMAL CONDITION OF GREASE OR SEALANT ON EXTERIOR CASE OF GEAR DUE TO THE MANUFACTURING PROCESS.

SB-PI-1533B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION ON POOR RADIO HANDS-FREE VOICE RECOGNITION PERFORMANCE OR SOUND QUALITY AFTER THE ONSTAR UPGRADE.

PIT5236G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.

00-03-10-002J

Service Bulletin/Repair Instructions

This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes.

PI0572C

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information on GM is implementing a new service strategy that uses a set of universal coaxial repair kits to service vehicles. This only applies to cable used for high frequency signals, such as cellular (OnStar®), satellite radio (XM) and GPS (navigation). The kits do NOT apply to the AM/FM cables.

PI0360F

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information on GM Accessory Remote start not working with onstars remotelink phone applications

09-06-04-026L

Service Bulletin/Repair Instructions

This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2® or GDS 2 (U.S. and Canada)

PIT5206D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205.

PIT5403A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

PIP4568S

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

08-00-89-014B

Service Bulletin/Repair Instructions

This informational bulletin provides information on what is needed to be prepared for TAC, caller preparedness and checklists and contacting U.S. technical Assistance and the use of strategy based diagnostics

07-00-89-037I

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Courtesy Transportation and Roadside Assistance Programs

16-NA-075

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to relearn the power folding mirriors and road test to correct a conditon of power fold away mirriors glass shakes or flutters at normal driving speeds

PIC6181

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

PIT4811B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with the steps on how to diagnose vehicles with a no crank with multiple Diagnostic Trouble Codes set in several different modules with Regular Production Option Code HP2. Technician will retrieve all the Diagnostic Trouble Codes that are set current in the vehicle. When there are multiple Diagnostic Trouble Codes technician may wonder were to start the diagnose process. Technician will address Diagnostic Trouble Codes P1AE2-P1AE4, P1B05, or P1B06 first as they're related to the High Voltage System Interlock Circuit for the high voltage system. Second Diagnostic Trouble Codes to address will be any loss of communication Diagnostic Trouble Codes related to the Powertrain expansion bus or the high speed LAN bus. Then address any low voltage concerns that may be related to a low 12 volt battery.

08-07-30-026C

Service Bulletin/Repair Instructions

This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary

PIP5232C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.

16-NA-069

Service Bulletin/Repair Instructions

This informational bulletin provides information on If the radar does not see any vehicles, structures, or objects for 15-25 minutes of driving, the system may think its blocked and display the ?Side Object Detection System Disabled? message.

03-00-89-006M

Service Bulletin/Repair Instructions

This informational bulletin provides information on New Vehicle Pre-Delivery Inspection (PDI) - Delivering Quality Vehicles and Generating Higher CSi Scores

03-06-03-004O

Service Bulletin/Repair Instructions

This informational bulletin provides information on Battery Testing and Warranty Replacement Requirements (North America ONLY)

06-00-89-029M

Service Bulletin/Repair Instructions

This informational bulletin provides information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability

09-00-89-002M

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to properly maintain vehicles in the dealer inventory

PIT4575D

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician vehicles with Regular Production Option Code HP2 may stall after shifting out of park quickly after a key crank. The 2-Mode Hybrid requires a certain amount of engine run time (1-2 seconds) from initial key crank before moving the gear shift indicator out of park. This is a normal condition and no parts should be replaced to try and resolve this concern.

PIT4669D

Service Bulletin/Repair Instructions

This Preliminary Information communication informs the technician Polyalkylene Glycol is not compatible with the Hybrid Polyester oil. When vehicles with Hybrid Air Conditioning system have been injected with any commercially available Ultra Violet dye the system should be flushed of all system oil. Most ultra violet dyes contain Polyalkylene Glycol oil.

PIT4897B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that vehicles with Regular Production Option Code HP2 will have a condition where were the 120V Accessory Power Outlet is inoperative. Dealer is to advise the customer that the 120V Accessory Power Outlet only functions after the engine has been started.

04-00-89-015K

Service Bulletin/Repair Instructions

This warranty informational bulletin provides a list of all the required operating procedures and explains them out to what is acceptable and not.

PIP5276F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides steps the technician will uses to diagnose and repair vehicles that have low oil pressure after an oil change with the engine Regular Production Option Code L20, L77, L94, L96, L99, L9H, LC8, LC9, LH9, LMF, LMG, LY6, or LZ1. Vehicle may have Service Engine Soon lamp with Diagnostic Trouble Code P0521 or Low Oil Pressure message on the instrument panel. Dealer will need to determine if bulletin 10-06-01-008 was completed. If the bulletin was performed inspect the left rocker cover. Dealer will insure the left rocker can hold water without leaking. If leaks are found apply room temperature vulcanization silicone to the rocker cover if possible or replace the left rocker cover.

PIT4597E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with the additional steps that are needed to help perform a successful brake bleed on the 2-Mode Hybrid with Regular Production Option Code HP2. With a battery maintainer installed on the vehicle use brake pressure bleeder that maintains 30 psi for the entire bleed procedure.

PIT4989B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with a list of modules to check for communication with the scan tool, if the navigation radio does not display the current Hybrid mode. Dealer will use a scan tool to check communication with Accessory Direct current Power Control Module, Air Condition control module, Drive Motor Generator Power Inverter Module, Engine Control Module, Battery Energy Control Module, and Transfer Case Control Module. Repair the loss of communication with the affected module and the power flow should return to the radio display.

12-03-10-001C

Service Bulletin/Repair Instructions

This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)

PIC5953A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

16-NA-055

Service Bulletin/Repair Instructions

This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near

PIT4211D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE AN OUTSIDE AIR TEMPERATURE INOPERATIVE. TO PERFORM AN INSTANT UPDATE OF THE AMBIENT TEMPERATURE SENSOR, PRESS AND HOLD THE RECIRC BUTTON AND AIR CONDITIONING BUTTON ON THE HEATER-VENT-AIR CONDITIONING CONTROL HEAD SIMULTANEOUSLY. IT IS ALSO POSSIBLE TO PERFORM THIS BY USING A SCAN TOOL IN SPECIAL FUNCTION MODE AND SELECT INSTANT UPDATE.

02-08-42-001I

Service Bulletin/Repair Instructions

This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not

11-00-89-005I

Service Bulletin/Repair Instructions

This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only)

04-06-01-029H

Service Bulletin/Repair Instructions

This informational bulletin provides information on Unscheduled Supplemental Services (Including Flushing Services and Additives) and Proper Use of GM Simplified Maintenance Schedules (U.S. Only)

PIP5226A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.

08-08-44-015F

Service Bulletin/Repair Instructions

This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs)

PIP5104B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A COLD ENGINE TICK NOISE FOR 50 SECONDS AT START UP. TECHNICIAN DETERMINES IF THE TICK NOISE IS POSSIBLY COMING FROM THE EXHAUST MANIFOLD, AS THIS NOISE COULD EASILY BE MISTAKEN FOR AN ENGINE TICK NOISE. IF YOUR SI DIAGNOSIS DOES NOT ISOLATE THE CAUSE OF THIS CONCERN, THIS CONCERN SHOULD BE CONSIDERED A VEHICLE DESIGN CHARACTERISTIC OF THE ECM CALIBRATION AND NO ADDITIONAL REPAIRS SHOULD BE PERFORMED.

01-08-42-001K

Service Bulletin/Repair Instructions

This informational bulletin provides information on exterior lamp condinsation and replacement guidelines

PIT4720D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT AFTER REPLACING THE INSTRUMENT PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS UNKNOWN. DEALER WILL NEED TO FOLLOW DEALER TO THE GENERAL MOTORS SERVICE POLICIES AND PROCEDURES MANUAL SECTION 5.2.4 ODOMETER SERVICING.

02-08-98-002F

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to properly repair rust on the hem flange on doors for vehicles that have the condition of rust showing at hem flange

16-NA-025

Service Bulletin/Repair Instructions

This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks

PIP4873A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS FOR DIAGNOSING AND REPAIRING VEHICLES WITH DIAGNOSTIC TROUBLE CODE P0C2B WITH OR WITHOUT P2797. TECHNICIAN SHOULD NOT REPLACE THE AUXILIARY TRANSMISSION FLUID PUMP. TECHNICIAN WILL FOLLOW PUBLISHED DIAGNOSIS INSPECT THE WIRING BETWEEN THE HPCM AND THE AUXILIARY TRANSMISSION FLUID PUMP CONTROL MODULE. IF THE WIRING TESTS OK WITH NO TERMINAL TENSION RELATED CONCERNS AT EITHER END OF THE CIRCUITS SUSPECT A POSSIBLE AUXILIARY TRANSMISSION FLUID PUMP CONTROL MODULE RELATED CONCERN.

06-08-50-009I

Service Bulletin/Repair Instructions

This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices

03-08-46-004R

Service Bulletin/Repair Instructions

This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)

PIP-5258

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE SERVICE ENGINE SOON AND A DIAGNOSTIC TROUBLE CODE P0011. IF THE TECHNICIAN HAS FOLLOWED SERVICE INFORMATION DIAGNOSTIC TROUBLE CODE FOR P0011AND THE ROOT CAUSE WAS NOT FOUND THE OIL PRESSURE AT THE OIL PRESSURE SENDER SHOULD BE CHECKED. ALSO THE NUMBER 2 CAM BEARING SHOULD BE INSPECTED.

PIP5258

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have Service Engine Soon and a Diagnostic Trouble Code P0011. If the technician has followed Service Information Diagnostic Trouble Code for P0011and the root cause was not found the oil pressure at the oil pressure sender should be checked. Also the number 2 cam bearing should be inspected.

PI0639C

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a procedure to apply dielectric grease and a piece of adhesive shim stock to the steering angle sensor connector to correct a condition of service stabilitak message displayed in DIC and DTC C0455 or C0710

13-02-32-001D

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to flush and bleed the power steering system to correct a condition of power steering noise or fluid leak from power steering pump, gear or high pressure hose during extreme low temperature conditions.

06-06-01-010C

Service Bulletin/Repair Instructions

This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period.

PIC5614A

Service Bulletin/Repair Instructions

Changing Turn-By-Turn Voice Response To Metric Or English Units

05-08-51-001H

Service Bulletin/Repair Instructions

This informational bulletin provides information on removing paint stains on the under side of protective shipping film

130232001D

Service Bulletin/Repair Instructions

Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions

PIT5353A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

PIC5480B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician certain accessories are being made available through the Integrated Business Partner. For detailed manufacturer warranty information, technical support, or for possible product defects refer to the Electronic Parts Catalog part listing for contact information to contact the appropriate supplier.

PIT4943D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

06-00-89-031D

Service Bulletin/Repair Instructions

OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification

07-08-49-020J

Service Bulletin/Repair Instructions

IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® – The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.

15-NA-079

Service Bulletin/Repair Instructions

OnStar Voice Fallback Number Update

15-NA-082

Service Bulletin/Repair Instructions

Clunking Noise from Front of Vehicle During Turns and/or Bumps Some customers may comment on a clunking noise originating from the front of the vehicle that is more predominant during turns or traveling over bumps. This may be caused by a damaged stabilizer shaft frame bracket. There have been some cases in which the bracket is cracked, as shown. This condition has been found to be the result of insufficient welds between the bracket and frame rail. There have been some cases on older vehicles of corrosion affecting the bracket

15NA082B

Service Bulletin/Repair Instructions

Clunking Noise from Front of Vehicle During Turns and/or Bumps

15-NA-069

Service Bulletin/Repair Instructions

This informational bulletin provides information for technicians on the reuse of fasteners and the proper reading of torque specifications.

PIP5232B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

00-03-10-006L

Service Bulletin/Repair Instructions

This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim.

PIT5214B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

PI1533A

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides repair information to correct a customer concern of poor radio hands-free voice recognition performance or sound quality after OnStar upgrade.

PIC3100E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

15-08-44-001F

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.

15-08-44-001G

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.

10-00-89-005E

Service Bulletin/Repair Instructions

This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel revised wiring repair labor operations and required additional information.

PI1344B

Service Bulletin/Repair Instructions

This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.

02-07-30-029Y

Service Bulletin/Repair Instructions

This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).

01-06-01-011I

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

08-08-44-029F

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).

PIP5341

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that engine runs and idles rough. Technician will find P0171 and or P0174. Technician will need to inspect the positive crankcase ventilation tube for a vacuum leak on the left side of the engine. Replace positive crankcase ventilation air tube and cover it with conduit to protect from repeat damage.

PI0799A

Service Bulletin/Repair Instructions

This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels.

PIT5083A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with the inside door panel material appearing to be pulling back from the door panel backing. Technician will check the windows for aftermarket window tint. Since this failure is not the result of a manufacturer defect, it would not be considered for coverage under a General Motors Warranty.

PIC5953B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

PIT4261D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

15-NA-030

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on the use of non-GM approved battery chargers and booster packs.

PIP5338

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

06-00-89-031C

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on proper engine and automatic transmission/transaxle identification.

15-06-03-001A

Service Bulletin/Repair Instructions

This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.

PIP4404F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.

08-08-44-029E

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).

05-03-07-009H

Service Bulletin/Repair Instructions

This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.

PIT5468

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about a connectivity concern with Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken place. Technician should delete all Bluetooth pairings and then reboot the Bluetooth device and the vehicle. After the vehicle and radio is booted back up repair the Bluetooth device.

PIT5464

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

PIT5465

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Turn By Turn directions may no longer be displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

PIP5325

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.

PIT4056H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a Antilock Braking System Malfunction Indicator Lamp on. Technician will find the scan tool will not communicate with the Electronic Brake Control Module. Technician will check the Yaw and Lateral Accelerometer Sensor and the Steering Wheel Angle Sensor supply voltage circuit 2087 Dark Green shorted and pulling down the internal circuitry of the Electronic Brake Control Module. Not all vehicles use circuit 2087 to supply voltage to the Steering Wheel Angle Sensor, so be sure to check Service Information for the specific vehicle that is being serviced. If circuit 2087 is backed out of the EBCM connector and communication returns, inspect for either this circuit being shorted to ground or for a sensor concern. Technician will repair the circuit as necessary and reroute to prevent the concern from reoccurring. If the technician is working on a full-size or utilities that have aftermarket lift kits the wheel speed sensor may be broken or shorted. Technician will repair the circuit as necessary.

PIT5049B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.

PIC6131

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the air conditioner blows warm air. If normal diagnostics from service information does not lead to a correction and it is found that the air conditioning compressor is not engaging check for any communication codes in the vehicle and address them first. It has been found in some cases that there is no communication with the sensing and diagnostic module that was causing the air conditioning compressor to not engage.

PIP4112Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

PI0564H

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

15-00-89-005

Service Bulletin/Repair Instructions

This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).

PIP5276E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. Inspect the engine for any oil leaks and repair if need. Technician should change the engine oil and replace the oil filter using a PF48e type filter.

10-08-110-001D

Service Bulletin/Repair Instructions

This informational bulletin provides information on the proper use of GM floor mats.

00-06-01-026G

Service Bulletin/Repair Instructions

This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.

07-00-89-037H

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on courtesy transportation and roadside assistance programs.

09-09-40-001C

Service Bulletin/Repair Instructions

This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.

PIT5236F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.

PIP-5276-E

Service Bulletin/Repair Instructions

CADILLAC/CHEVROLET/GMC: ON SOME VEHICLES AND/OR TRUCKS, INSTRUMENT CLUSTER WILL ILLUMINATE, AFTER AN OIL CHANGE, INDICATING LOW OIL PRESSURE AND/OR SES LAMP WILL ILLUMINATE. MODEL 2007-13 CANYON, SIERRA, SAVANA, YUKON, CTS-V, ESCALADE, AVALANCHE, CAMARO SS, COLORADO, CORVETTE, EXPRESS, SILVERADO, SUBURBAN, TAHOE. *PE

09-00-89-002L

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer inventory.

PIC5932A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.

PIT5236E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.

09-06-04-026K

Service Bulletin/Repair Instructions

This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline engines using Tech 2® or GDS 2 (U.S. and Canada).

99-01-39-004G

Service Bulletin/Repair Instructions

This technical bulletin provides repair information for the correction of a customer concern of short duration musty odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.

03-06-03-003E

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on ACDelco® replacement battery warranty procedures.

03-07-29-004J

Service Bulletin/Repair Instructions

This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change.

03-00-89-006L

Service Bulletin/Repair Instructions

This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores.

PI0564G

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only)

PIP4648C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that replacement transfer case halves will not be threaded. No additional thread tapping will be necessary to assemble the transfer case as the attaching metric bolts are self-tapping. Drive the bolts into the new case and torque them to specification.

PIP4786B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure message. Technician may also find a Diagnostic Trouble Code P0521 in the Engine Control Module. Technician should follow all published Service Information diagnosis. When using a scan tool if the oil pressure is low but the oil pressure at the oil filter housing is correct, technician should inspect the Valve Lifter Oil Filter for debris/sludge that could be restricting oil flow to the oil pressure sensor. Technician should remove the Valve Lifter Oil Filter and clean it. If the Valve Lifter Oil Filter cannot be cleaned replace it.

PIT4667D

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician of additional steps for diagnosing General Motors high speed local area network. This should only be used if normal service information doesn?t lead to a diagnosis this is not a replacement for normal service information.

01-08-51-003E

Service Bulletin/Repair Instructions

This informational bulletin provides recommendations and product information for application of anti-corrosion materials

05-06-04-022M

Service Bulletin/Repair Instructions

This informational bulletin provides information on TOP TIER Detergent Gasoline and available retail brands.

06-00-89-029K

Service Bulletin/Repair Instructions

This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product availability.

PIC5491G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

PIT5442

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.

03-06-03-004N

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).

PIC5650B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

08-07-30-021H

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct customer concerns of loss of high speed GMLAN communications, intermittent no crank, IP gauge fluctuation, intermittent door lock cycling /chime operation, various IP warning lamps illuminated, transmission may not shift, communication DTCs U0073, U0100, U0101, U0102, U0109, U0121 or U0140 set.

07-06-04-019E

Service Bulletin/Repair Instructions

This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.

02-00-89-002O

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on when and how to submit a Field Product Report (FPR) (U.S. Dealers Only).

PIC6107

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.

PIP5258A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0011. If the technician has followed all published Service Information diagnosis and has not come to a conclusion, technician should check the oil pressure at the oil pressure sender. Then the number two cam bearing should be inspected.

PIT4610E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that First Responder Guides for General Motors vehicles can be accessed via the web at http://www.gmstc.com.

PIT5214A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

99-00-89-019M

Service Bulletin/Repair Instructions

This informational bulletin provides dealership personnel with Global Warranty Management (GWM), Warranty Parts Center (WPC), and Parts Return Program information.

15-08-44-001C

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.

PIP5276D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. If Diagnostic Trouble Code P0521 setting in cold weather and it has a PF48E oil filter, change the filter to a UPF48R if one is available.

PIT5384A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.

PIT5236D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.

09-00-89-002K

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer inventory.

PIP5276C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. If Diagnostic Trouble Code P0521 setting in cold weather and it has a PF48E oil filter, change the filter to a PF48 if one is available. If there is no availability of oil filter PF48 use oil filter UPF48R.

05-06-04-035E

Service Bulletin/Repair Instructions

This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles.

15-00-89-004A

Service Bulletin/Repair Instructions

This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.

00-06-01-026F

Service Bulletin/Repair Instructions

This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.

15-08-44-001A

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.

15-08-44-001B

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.

PIT5403

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

PI0091B

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides repair information to correct a customer concern of Iitermittently key will not rotate in door or ignition lock cylinder.

02-08-42-001H

Service Bulletin/Repair Instructions

This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.

15-00-89-004

Service Bulletin/Repair Instructions

This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage.

PIT5028B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle starts and stalls on the first initial start after the replacement of the Theft Deterrent Module. Technician will need to use the scan tool to check Manufactures Enable Counter. If the number is anything other than zero the Manufactures Enable Counter will need to be reset. To reset the Manufactures Enable Counter counter, the ignition key can be cycled the number equal to the Manufactures Enable Counter counter.

PI0345F

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides inspection and repair information to correct a customer concern of XM/Cellular Mobile Phone/OnStar Antenna looseness or damage, XM/Cellular/OnStar reception performance degraded, rattle/flutter/squeak noise, wind noise/whistle at highway speeds, water leak on headliner at sunvisor.

PIT5399

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

PIC4310L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

PIP5282

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down.

PIP4786A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure message. Technician may also find a Diagnostic Trouble Code P0521 in the Engine Control Module. Technician should follow all published Service Information diagnosis. When using a scan tool if the oil pressure is low but the oil pressure at the oil filter housing is correct, technician should inspect the Valve Lifter Oil Filter for debris/sludge that could be restricting oil flow to the oil pressure sensor. Technician should remove the Valve Lifter Oil Filter and clean it. If the Valve Lifter Oil Filter cannot be cleaned replace it.

05-08-46-009D

Service Bulletin/Repair Instructions

This informational bulletin adds the 2014 and 2015 model years to information of a language change for OnStar System (U.S. and Canada only).

PIP4600E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the 2ML70 Transmission Assembly will be placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.

12-07-30-001E

Service Bulletin/Repair Instructions

This informational bulletin provides information on the Product Quality Center (PQC) assembly replacement process for Service Agents not required to contact PQC prior to assembly replacement.

13-08-116-001B

Service Bulletin/Repair Instructions

The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

00-05-22-002O

Service Bulletin/Repair Instructions

This informational bulletin provides technicians with a brake lathe calibration procedure.

PIT5236C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may OnStar inoperative and Navigation/GPS/Compass issues. Technician may find Diagnostic Trouble Codes B101D sym 3C and or F0. Technician will gather data using a scan tool and contact General Motors Technical Assistance Center for further assistance. After approval technician will replace the OnStar module.

PIP5276B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on during a cold start in temperatures below 0 degrees Fahrenheit. Technician will find Diagnostic Trouble Code P0521. Technician will check the oil filter part number. If the part number is PF48E change the oil filter to a PF48. If a PF48 is not available then install a new UPF48R.

13-00-89-008A

Service Bulletin/Repair Instructions

This informational bulletin communicates GM wiring repair strategy information.

PI1440

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides technicians with diagnostic tips for a customer concern of odor emanating from HVAC system.

04-00-89-015J

Service Bulletin/Repair Instructions

This warranty administration bulletin communicates GM required operating procedures (U.S. only) for service operations.

09-00-89-016D

Service Bulletin/Repair Instructions

This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications.

PIP5276A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on during a cold start in temperatures below 0 degrees Fahrenheit. Technician will find Diagnostic Trouble Code P0521. Technician will check the oil filter part number. If the part number is PF48E change the oil filter to a PF48. If a PF48 is not available then install a new PF48E.

12-06-01-008B

Service Bulletin/Repair Instructions

This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).

15-00-90-001

Service Bulletin/Repair Instructions

This informational bulletin provides technicians with diagnostic tips for preventing oil leaks after changing oil and filter.

PIP5276

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on during a cold start in temperatures below 0 degrees Fahrenheit. Technician will find Diagnostic Trouble Code P0521. Technician will check the oil filter part number. If the part number is PF48E change the oil filter to a PF48.

02-07-30-029X

Service Bulletin/Repair Instructions

This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).

08-08-45-004D

Service Bulletin/Repair Instructions

This informational bulletin provides information for installing a diode to solenoid/relay to suppress voltage spikes in conjuction with installation of electrical aftermarket accessories-battery, ignition and ground feeds-(do not splice into wiring harness).

PI0020D

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides technicians with information on the normal condition of white, milky or cloudy appearance of front differential fluid.

15-08-44-001

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.

15-08-73-001

Service Bulletin/Repair Instructions

This informational bulletin provides information on communication with OnStar® module after Canadian cellular upgrade.

PI02003D

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides technicians a recommendation for when they are performing a front end alignment and find an alignment dowel pin missing .

15-00-89-003

Service Bulletin/Repair Instructions

This informational bulletin provides information on dealer reimbursement procedures for Customer Assistance Center (CAC) Tier 1 and Tier 2 empowerment tools: diagnostic fee, short term rental, and up-front towing (U.S. only).

05-06-04-060A

Service Bulletin/Repair Instructions

This informational bulletin communicates Information to technicians on control module Diagnostic Trouble Code(s) (DTC)(s) P0601, P0602, P0603, P0604, P0606, P062F, P06F3, P1621 which can be shared in multiple modules.

PIT5264C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

08-03-10-004B

Service Bulletin/Repair Instructions

This informational bulletin communicates comprehensive instructions to GM Dealers and authorized GM Accessory Distributor/Installers as to the proper methods for mounting, balancing, and installing accessory wheels and tires.

05-00-89-055E

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information to clarify proper transaction administration of GM Dealer Empowerment Program and Goodwill Cases.

15-08-42-001

Service Bulletin/Repair Instructions

This informational bulletin communicates GM's position on exterior lighting components ?tinted or smoked? by an outside vendor.

PI1018A

Service Bulletin/Repair Instructions

This preliminary informational bulletin adds the 2015 model year to repair information on correcting a customer concern of poor, limited, reduced Remote Keyless Entry (RKE) or Remote Vehicle Start (RVS) range.

05-03-10-020F

Service Bulletin/Repair Instructions

This informational bulletin communicates GM's position on use of nitrogen gas in tires.

PI1404

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a diagnostic tip for low line pressure or pressure regulator valve stuck after transmission service pump cover replacement.

05-08-51-001G

Service Bulletin/Repair Instructions

This informational bulletin provides information to correct a dealer concern of what they perceive to be paint staining when the protective shipping film is removed from certain vehicles.

01-00-89-010K

Service Bulletin/Repair Instructions

This informational bulletin adds 2014 - 2015 model years to information regarding comeback prevention and using Customer Concern Verification Sheets (CCVS).

06-08-47-001K

Service Bulletin/Repair Instructions

This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty.

10-08-45-001E

Service Bulletin/Repair Instructions

This informational bulletin updates information on electrical ground repairs using new replacement fasteners with conductive finish.

PIT4539S

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the Drive Motor Generator Control Module and Accessory Power Module are being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.

00-03-10-002I

Service Bulletin/Repair Instructions

This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of chromed aluminum wheels, along with warranty information regarding these conditions.

PIP4568R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

07-06-03-009D

Service Bulletin/Repair Instructions

This informational bulletin adds models to information on voltmeter gauge fluctuation due to regulated voltage control system and concerns about camper/trailer battery charging.

PI1394

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.

PIT3271G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

03-06-03-003D

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on ACDelco® replacement battery warranty procedures.

11-00-89-004A

Service Bulletin/Repair Instructions

This warranty administration bulletin adds 2012 - 2015 model years to information communicating a change in the product field action customer reimbursement procedure (U.S. Dealers Only).

PIC3278F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

PIC4310K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

07-06-03-009C

Service Bulletin/Repair Instructions

This informational bulletin adds 2011 - 2014 model years to information on voltmeter gauge fluctuation due to regulated voltage control system and concerns about camper/trailer battery charging.

09-06-04-026J

Service Bulletin/Repair Instructions

This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline engines using Tech 2® or GDS 2 (U.S. and Canada).

PI0345E

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides inspection and repair information that may be helpful to correct customer concerns of XM/Cellular Mobile Phone/OnStar® antenna looseness or damage, XM/Cellular/OnStar® reception performance degraded, rattle/flutter/squeak noise, wind noise/whistle at highway speeds, and/or a water leak on headliner at sunvisor.

PI0360E

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information that accessory remote start does not work with OnStar RemoteLink? phone application.

03-00-91-001G

Service Bulletin/Repair Instructions

This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.

15-06-03-001

Service Bulletin/Repair Instructions

This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.

PI1385

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information that the tire pressure monitor (TPM) sensors must always be re-learned when accessory wheels are installed on the vehicle.

030729004I

Service Bulletin/Repair Instructions

This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises.

PIT5236B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may OnStar inoperative and Navigation/GPS/Compass issues. Technician may find Diagnostic Trouble Codes B101D sym 3C and or F0. Technician will gather data using a scan tool and contact General Motors Technical Assistance Center for further assistance. After approval technician will replace the OnStar module.

PI0655A

Service Bulletin/Repair Instructions

This preliminary information bulletin provides information on how to remove stainless steel wheel nut caps with the matching depth of socket used on the wheel nut.

PI0345D

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides procedures to inspect , replace, or repair the XM radio antenna to correct the customers concern loss XM services, noise and/or water leak.

030848006J

Service Bulletin/Repair Instructions

This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.

1008110001C

Service Bulletin/Repair Instructions

This information provides the proper way to install the floor mats .

100089005D

Service Bulletin/Repair Instructions

This warranty informational bulletin advised the technician that when performing a wiring repair, more information is required.

PIT5236A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492.

14515

Service Bulletin/Repair Instructions

Chassis Electronic Control Module Internal Contamination

PIT5074H

Service Bulletin/Repair Instructions

J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.

10-06-01-008M

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to correct the customers concern to replace the left side valve cover and active fuel management oil deflector to reduce oil consumption.

04-00-89-015I

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.

06-00-89-026M

Service Bulletin/Repair Instructions

This warranty bulletin provides labor operation numbers for customer concerns that can't be duplicated.

PIC5492C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.

PIT5353

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

05-06-04-022L

Service Bulletin/Repair Instructions

This informational bulletin provides information on top tier fuels and what brands are available.

PI1344A

Service Bulletin/Repair Instructions

This preliminary bulletin provides a procedure to remove and inspect the clutch select solenoid valve for damage, located in the valve body to correct the customers concern of reduced acceleration at low speeds and trans slip at lauch.

PIP5029F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

10-08-98-002A

Service Bulletin/Repair Instructions

This information bulletin explains the use of drilling high strength steel in a collision repair and the GM recommended CryoCobalt Drill bit.

99-04-20-002I

Service Bulletin/Repair Instructions

This informational bulletin explains a normal condition for what and how the drive line can clunk.

PIT4322G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

10-06-01-008L

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to correct the customers concern to replace the left side valve cover and active fuel management oil deflector to reduce oil consumption.

PI0564F

Service Bulletin/Repair Instructions

This preliminary bulletin provides a procedure to paint the areas of the frame, if there are signs of rust/corrosion after the wax coating peeled off.

09-06-04-026I

Service Bulletin/Repair Instructions

This informational bulletin was created to help technician identify non GM calibrations for the gasoline engines and the damages that may be caused by aftermarket calibrations

09-06-04-026H

Service Bulletin/Repair Instructions

This informational bulletin was created to help technician identify non GM calibrations for the gasoline engines and the damages that may be caused by aftermarket calibrations

PIT5264B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

11-00-89-005H

Service Bulletin/Repair Instructions

This warranty bulletin clarifies the use of dealer empowerment to satisfy the customer.

13-00-89-004J

Service Bulletin/Repair Instructions

This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.

990420002I

Service Bulletin/Repair Instructions

Information on Driveline Clunk Noise

PIT5099A

Service Bulletin/Repair Instructions

A/C Blows Warm Or Poor Performance.

PIT5195B

Service Bulletin/Repair Instructions

Speedometer Needle Accuracy Information.

14-00-89-003A

Service Bulletin/Repair Instructions

This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and now is refered to Article 3.2.9 of the 1st addition manual for details of Technician Identification and Accounting of Labor Time

PI1344

Service Bulletin/Repair Instructions

This preliminary bulletin provides a procedure to remove and inspect the clutch select solenoid valve for damage, located in the valve body to correct the customers concern of reduced acceleration at low speeds and trans slip at lauch.

G-203256

Service Bulletin/Repair Instructions

14262 - SPECIAL COVERAGE. ON SOME HYBRID 2-MODE (HP2) VEHICLES, THE ACCESSORY POWER MODULE (APM) MAY NOT INITIALIZE WHEN THE VEHICLE IS STARTED IN COLD TEMPERATURES AND THE APM IS COLD. ONCE THE APM WARMS UP, IT WILL INITIALIZE AND PERFORM AS DESIGNED. HOWEVER, DURING THE TIME THAT THE APM IS NOT OPERATIONAL, IT COULD RESULT IN A LOSS OF POWER STEERING ASSIST AND THE BATTERY MAY NOT CHARGE. IF THIS CONDITION OCCURS, THE SERVICE POWER STEERING, SERVICE HYBRID SYSTEM, OR SERVICE BATTERY CHARGING SYSTEM MESSAGE WILL APPEAR IN THE DRIVER INFORMATION CENTER, THE MALFUNCTION INDICATOR LAMP AND RED BATTERY TELLTALE MAY ILLUMINATE, AND DTC U1821 AND U182A WILL BE PRESENT. DEALERS ARE TO REPLACE THE APM.

06-08-43-003E

Service Bulletin/Repair Instructions

This informational bulletin explains how to care for wiper blades.

PIP5232A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

07-08-49-020I

Service Bulletin/Repair Instructions

This informational bulletin provides a quick guide to updating which model vehicle after replacing the IPC.

PIT5264A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

PIT5338

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have a Service Power Steering or Service Hybrid System message displayed on the Driver Information Center, Charging System indicator lamp on, Loss of power steering assist, and or Loss of 12 volt battery power. Technician will need to replace the Accessory DC Power Control Module.

04-00-89-015H

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.

PI1098A

Service Bulletin/Repair Instructions

This preliminary bulletin provides a procedure on how to cold crank test a battery in a vehicle.

PIC6036

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.

PIP5232

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

04-06-04-047M

Service Bulletin/Repair Instructions

This informational bulletin states that it no longer valid and refers to a new bulletin.

08-08-44-015E

Service Bulletin/Repair Instructions

This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs

PI0564E

Service Bulletin/Repair Instructions

This preliminary bulletin provides information and a procedure for repairing rusted frames caused by the wax coating peeling off.

PIP5226

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

10-08-110-001B

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to use floor mats.

05-06-04-022K

Service Bulletin/Repair Instructions

This informational bulletin provides information on top tier fuels and what brands are available.

10-08-44-006C

Service Bulletin/Repair Instructions

This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website.

07-00-89-036G

Service Bulletin/Repair Instructions

This informational bulletin ask the dealers for digital pictures to better enhance field reports only.

02-00-89-002N

Service Bulletin/Repair Instructions

This informational bulletin provides additional information to the technicians and how to submit a field product report.

10-00-89-006E

Service Bulletin/Repair Instructions

This information bulletin provides the dealers on how to submit a product information report.

07-08-50-022C

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to shim the second row seat to correct the customers concern of a rattle, hard to latch or unlatch, and/or power relaese fold and tumble not fully functioning.

03-06-03-004M

Service Bulletin/Repair Instructions

This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.

09-00-89-002J

Service Bulletin/Repair Instructions

This informational bulletin provides information to the dealers on properly maintaining vehicles in inventory.

00-03-10-006K

Service Bulletin/Repair Instructions

This informational bulletin provides the technician with information on tire radial force variations and how to use it.

13-02-32-001B

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to repair any power steering leak that may be caused from extremely low temperatures and use the recommended fluid.

PI02003C

Service Bulletin/Repair Instructions

This preliminary bulletin provides a diagnostic tip to install a temporary dowl rod to perform an alignment.

PIT3099M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

PI1290

Service Bulletin/Repair Instructions

This preliminary bulletin provides a procedure to replace the windshild to correct the customers concern of a loose mirrior and/or bracket fell off.

PIT4543B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the operation of the ground illumination lamp. For the puddle lamps to operate they must be turned on using the Drivers Information Center buttons and it must be dark outside.

13-02-32-001C

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to repair any power steering leak that may be caused from extremely low temperatures and use the recommended fluid.

SB-13-02-32-001

Service Bulletin/Repair Instructions

BUICK/CADILLAC/CHEVROLET/GMC: DURING EXTREME LOW TEMPERATURE CONDITIONS, THE POWER STEERING MAKES NOISES OR FLUID LEAKS FROM HIGH PRESSURE HOSE, POWER STEERING PUMP OR GEAR. *PE UPDATED 9/30/13. *PE UPDATED 11/7/14. *PE

PIC5959B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.

99-01-39-004F

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.

PIC4310J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

PIC5759A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.

PIT5067A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have "Press check to turn off motion sensor" message on the Driver Information Center. If this message is displayed, the vehicle has a General Motors Accessory shock sensor, motion sensor or inclination sensor installed. Dealer should advise the customer this is normal operation with this accessory installed.

00-06-01-012E

Service Bulletin/Repair Instructions

This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.

PIT5206C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205.

12-03-10-001B

Service Bulletin/Repair Instructions

This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.

PIP5163A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

00-00-89-027H

Service Bulletin/Repair Instructions

This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.

PIP3783D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on or reduced engine power message. Technician may find Diagnostic Trouble Codes P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138. Technician will need to inspect the Accelerator Pedal Position circuits for poor terminal tension.

02-00-89-002M

Service Bulletin/Repair Instructions

This informational bulletin provides additional information to the technicians and how to submit a field product report.

PI0938A

Service Bulletin/Repair Instructions

This preliminary bulletin provides information on what labor operation number to use for various electrical/electronic control issues.

10-00-89-006D

Service Bulletin/Repair Instructions

This information bulletin provides the dealers on how to submit a product information report.

10-08-46-001B

Service Bulletin/Repair Instructions

This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions and to correct the customers concern of the radio being loud during navigation.

PIP4902H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

14-00-89-003

Service Bulletin/Repair Instructions

This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the requirements for the dealer to comply.

PI-1280

Service Bulletin/Repair Instructions

CADILLAC/CHEVROLET/GMC: LOSS OF PROPULSION, WHEN SPEED IS LESS THAN 5 KM/H (3MPH), SERVICE HYBRID SYSTEM IS DISPLAYED IN DRIVER INFORMATION CENTER (DIC) AND MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATES. MODEL 2008-2013 ESCALADE, SILVERADO, TAHOE, SIERRA, YUKON. *PE

PIT-5206

Service Bulletin/Repair Instructions

GENERAL MOTORS: OWNERS MAY COMPLAIN ABOUT UNWANTED BRAKING, OR REDUCED ENGINE POWER. THERE MAY ALSO BE SOME UP AND DOWN SHIFTS WITH THE TRANSMISSION. *KB UPDATED 10/15/14. *PE UPDATED 11/12/14. *PE

Recalls

Service Bulletin/Repair Instructions

Vehicle Recalls

050308002F

Service Bulletin/Repair Instructions

This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that has a fluid residule from a possible external source from a leaking shaft seal.

PIP4112P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

PI1266

Service Bulletin/Repair Instructions

This preliminary bulletin explains to the technician to use the vin when reprogramming the radio using the techline/service programming systems.

PI0373B

Service Bulletin/Repair Instructions

This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds.

PIC5088E

Service Bulletin/Repair Instructions

This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.

PIC5588B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

05-00-89-029C

Service Bulletin/Repair Instructions

This preliminary bulletin provides a information to the dealer for the requirements need for equipment.

PIP4401E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have the check engine light, tow/haul, Supplemental Inflatable Restraint, cruise control or other various indicators or warning lamps will not come on in the instrument panel. Tech will need to the Tech 2 scan tool to command the instrument panel indicator lights on. If the light do not turn on technician should inspect (AUX HVAC) 10 amp fuse in the under-hood fuse block for open or high resistance.

12-00-89-002B

Service Bulletin/Repair Instructions

This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.

03-00-89-006K

Service Bulletin/Repair Instructions

This information bulletin provides dealers with more information on how to better prep a vehicle for pre-delivery.

PIP4653E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0601, P0603, P0604, P062F or P1621 stored in the Transmission Control Module. Technician will need to ensure that the Diagnostic Trouble Codes are set in the Transmission Control Module. If the Diagnostic Trouble Codes are only set in the Transmission Control Module reprogram the Transmission Control Module.

PIT5180A

Service Bulletin/Repair Instructions

Whistle Noise From Drivers Side A Pillar Area.

PIT5209A

Service Bulletin/Repair Instructions

Unwanted Alarm Sounding (GM Accessory Inclination Sensor Mounting)

09-03-10-013B

Service Bulletin/Repair Instructions

This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill the tire can be properly repaired under the new tire warranty.

02-07-30-029W

Service Bulletin/Repair Instructions

This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.

12-07-30-001D

Service Bulletin/Repair Instructions

This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.

PIT5292

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an air condition that has poor performance during high ambient temperatures. Technician will need to check the refrigerant charge and record the recovered amount on the repair order. Technician should recharge the system if needed. Technician will also need to verify if Global Diagnostic System 2 high side readings match a high side pressure gauge. If the readings vary greatly diagnostics will need to be performed.

03-06-03-004L

Service Bulletin/Repair Instructions

This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.

PIC5687D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that loose connection between the vehicle and a Bluetooth phone. Technician will need to use a scan tool to check the "Firmware Over-the-Air" value. If the "Firmware Over-the-Air" value is up to date and customer's concern is still present contact General Motors Technical Assistance Center for further assistance.

00-03-10-006J

Service Bulletin/Repair Instructions

This informational bulletin provides the technician with information on tire radial force variations and how to balance a tire using the balancer.

03-03-10-007I

Service Bulletin/Repair Instructions

This informational bulletin explains a normal condition of new tires may shake and vibrate for the first few miles.

PIP4833E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the Auxiliary Transmission Fluid Pump Control Module and Auxiliary Transmission Fluid Pump placed on parts restriction by General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.

12-08-132-001B

Service Bulletin/Repair Instructions

This informational bulletin explains if the fuse is open when the customer plugs in the trailer, that it may be the cause if diagnostics finds no problems to that point.

13-00-89-004I

Service Bulletin/Repair Instructions

This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.

06-00-89-029J

Service Bulletin/Repair Instructions

This informational bulletin provides tips on how to care for the interior of the vehicle using products.

PIP3119M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.

PI1235

Service Bulletin/Repair Instructions

This preliminary bulletin provides information to the technician, to check for loose grounds and the correct labor op to use

PI1233

Service Bulletin/Repair Instructions

This preliminary bulletin states to add the DTC symptom byte to the documentation to help aid engineering pinpoint concerns when trying to locate a root cause.

05-06-04-035D

Service Bulletin/Repair Instructions

This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.

PIP4600D

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the 2ML70 Transmission Assembly will be placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.

02-07-30-029V

Service Bulletin/Repair Instructions

This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.

13147A

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

PI-1235

Service Bulletin/Repair Instructions

GENERAL MOTORS: DUE TO LOOSE GROUND TERMINAL CONNECTIONS, IN SOME VEHICLES AND TRUCKS EXPERIENCE, ACCESSORIES MALFUNCTIONS, DIC MESSAGES, IPC WARNING INDICATORS, SES LIGHT ON. *PE

PIT4821D

Service Bulletin/Repair Instructions

High Voltage 2-Mode Battery Parts Restriction-TAC

PIT5206B

Service Bulletin/Repair Instructions

Unwanted Grade Braking - Low Power - And/Or Transmission Busy Shifting.

09-00-89-002I

Service Bulletin/Repair Instructions

This informational bulletin provides information to the dealers on properly maintaining vehicles in inventory.

01-08-42-001J

Service Bulletin/Repair Instructions

This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.

02-08-42-001G

Service Bulletin/Repair Instructions

This informational bulletin is to assist with the identification of issues that are not considered warrantable.

PIC5491F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

PIT3099L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

14-06-130-001

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to disable high voltage safely.

13-00-89-004H

Service Bulletin/Repair Instructions

This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles.

PI1216

Service Bulletin/Repair Instructions

This preliminary bulletin provides a procedure to install a new cabin air filter kit for vehicles that did not have one if the customer whants one installed to fix the concern of dust intruding into cabin interior.

PIP3343E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.

1406130001

Service Bulletin/Repair Instructions

High Voltage Safety ? High Voltage Disabling

03-06-03-004K

Service Bulletin/Repair Instructions

This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not

PIP3343D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.

13-00-89-004G

Service Bulletin/Repair Instructions

This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.

PIC5374C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Technicians will need to remove power from the Vehicle Communication Interface Module for one hour and retest for the concern.

PIC5959A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.

PIT5264

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.

PIC4801F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.

PI0688F

Service Bulletin/Repair Instructions

Poor Voice Quality During Bluetooth Call or OnStar® Personal Call.

PIT4864F

Service Bulletin/Repair Instructions

Information On Requests To Add OnStar Bluetooth Option.

08-08-48-003H

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to install double sided tape to the windshield molding to correct the customers concern of a tapping or clicking noise at the winshield area.

PIC3011H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.

PIC5491E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.

12-07-30-001C

Service Bulletin/Repair Instructions

This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.

PIP5184

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that when replacing the camshaft part number 12626660. Technician will need to ensure that the date code and the finish of the camshaft. If the cam is discolored or has chatter marks, have parts department send the cam back as (MR code7) new defective.

SB-12286-A

Service Bulletin/Repair Instructions

12286A - SERVICE UPDATE (REVISED EXPIRATION DATE). THIS BULLETIN PROVIDES A SERVICE PROCEDURE TO INSTALL A RUBBER AND A FOAM SPACER TO THE BACKSIDE OF BOTH REAR SIDE DOOR WINDOW REVEAL MOLDINGS ON CERTAIN VEHICLES. ON SOME OF THESE VEHICLES, THERE MAY BE INADEQUATE CLEARANCE BETWEEN THE REAR SIDE DOOR AND THE MOLDING. DURING MOLDING INSTALLATION, PAINT DAMAGE MAY HAVE OCCURRED. IN ADDITION, WHEN THE MOLDING IS EXPOSED TO ELEVATED TEMPERATURES, IT COULD EXPAND AND CAUSE PAINT DAMAGE.

09-03-10-016B

Service Bulletin/Repair Instructions

This informational bulletin explains how to balance a chrome wheel without damaging the chrome face of the rim.

10-08-64-002C

Service Bulletin/Repair Instructions

This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.

12-03-10-001A

Service Bulletin/Repair Instructions

This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.

12-03-10-002A

Service Bulletin/Repair Instructions

This informational bulletin provides the technician the proper way to install and torque the wheel.

05-03-10-020E

Service Bulletin/Repair Instructions

This informational bulletin explains the use of Nitrogen in GM tires.

07-03-10-008D

Service Bulletin/Repair Instructions

This bulletin provides information regarding the normal tire wear condition of slight or mild tire feathering and recommended practices.

08-03-10-006E

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on.

13-00-89-004F

Service Bulletin/Repair Instructions

This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.

PIT4539R

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the Drive Motor Generator Control Module, also known as PIM) for the 2-Mode Hybrid Utilities and Trucks are being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.

PIT4943C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

02-08-98-002E

Service Bulletin/Repair Instructions

The informational bulletin provides a procedure to remove and repair rust from a Hem Flange.

05-08-48-001D

Service Bulletin/Repair Instructions

This warranty administration bulletion provides the dealer technician information and guidelines for claiming a windshield.

99-01-39-004E

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.

PIT4610D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that First Responder Guides for General Motors vehicles can be accessed via the web at http://www.gmstc.com.

PI0488D

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a procedure to inspect the transmissions filter for splits or cracks to correct the customers concern for no forward, reverse or slips.

PIC5453A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

PIP5104A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a cold engine tick noise for 50 seconds at start up. Technician determines if the tick noise is possibly coming from the exhaust manifold, as this noise could easily be mistaken for an engine tick noise. If your SI diagnosis does not isolate the cause of this concern, this concern should be considered a vehicle design characteristic of the ECM calibration and no additional repairs should be performed.

99-08-51-007F

Service Bulletin/Repair Instructions

Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility — Outside Company later in this bulletin.

04-00-89-053F

Service Bulletin/Repair Instructions

This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.

PIC5959

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.

PIT4474E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have navigation or radio screen is blank or flashes on and off, no sound from speakers, and rear DVD screen inoperative. Technician will find Diagnostic Trouble Codes B1265, B1288, or B1289. Technician will need to repair circuit 7066.

PIT4684B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a rear camera display being inoperative when shifting into reverse. Technician should check for a loose or disconnected X421/X322 connector behind the right side "C" pillar trim. Technician should also check for pinched, Open or shorted wires on camera circuits 7641, 7642, and 6799.

11-00-89-002B

Service Bulletin/Repair Instructions

This informational bulletin was created to inform that any accessories that are install from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months).

PIC5953

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

PIP5089A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code C0569 that will not clear. Technician should be advised if there are any issues with the rotational position sensor, incremental position sensor, encoder motor, motor A or B circuits, rotational position sensor or incremental position sensor circuits when the transfer case control module attempts to determine location the location cannot be determined correctly.

PIT5195A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

PIP4112N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

PIT4954D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Suspension System message on the Driver Information Center and the rear suspension ride height is incorrect. Technician will find Diagnostic Trouble Code C0696 or C0711 set in Electronic Suspension Control. Technician will need to inspect air compressor assembly for wire damage and repair any damage do not replace the complete air compressor assembly. Some vehicles may have a Service Suspension System message on the Driver Information Center and may also comment that the rear suspension ride height may be low under a heavy payload. Technician will follow published Service Information diagnostics and if determine if the sensor needs to be replaced technician will need to replace a complete air filter, dryer, and sensor assembly. Some vehicles may have a loose hose hanging down in the left rear of the vehicle. Technician will replace the auto leveling compressor air inlet filter and hose assembly. Also some vehicles may have automatic level control compressor is no longer performing a self-test at start up. Be advised the automatic level system normally will not or very infrequently cycle the compressor at key up.

PIP3140F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.

01-07-30-042H

Service Bulletin/Repair Instructions

This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition.

08-08-44-029D

Service Bulletin/Repair Instructions

This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to.

PIP4568Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

04-00-89-015G

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.

PIP5169

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are setting Diagnostic Trouble Code P0300 after engine repairs. Technician will need to ensure that injector connectors for cylinder 5-7 and 6-8 are not crossed.

PIT4423H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an aftermarket, add-on back up alarm will sound when unlocking the doors with the Remote Keyless Entry remote. Technician can correct this concern by turning off the perimeter lighting feature on vehicles with Driver Information Center controls or install an isolation relay in-line to the backup alarm.

14-00-89-001

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Premium care maintenance eligibility for vehicle services and maintenance in the U.S. and Canada.

04-00-89-015F

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.

07-00-89-037G

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on GM?s policy for comprehensive courtesy transportation to its customers.

140089001

Service Bulletin/Repair Instructions

Cadillac Premium Care Maintenance Eligibility for United States and Canadian Vehicles

PI0281D

Service Bulletin/Repair Instructions

Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

10-00-89-006C

Service Bulletin/Repair Instructions

This informational bulletin provides directions on submitting different PIRs

08-08-44-015D

Service Bulletin/Repair Instructions

This preliminary bulletin explains physical damage to radios and IPCs must be reviewed and validated if covered under GM warranty or not.

13-00-89-004E

Service Bulletin/Repair Instructions

This preliminary information bulletin provides a revision of 13-00-89-004D to include updated information.

PI0754A

Service Bulletin/Repair Instructions

This preliminary bulletin explains the marks in the glass are normal when wearing polarized sunglasses and do not replace any glass for this reason.

05-00-89-072C

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.

PI0592C

Service Bulletin/Repair Instructions

This preliminary bulletin provides information on Service Programming System (SPS) Errors (E4398, E4399, E4403, E4404, E4413, E4414, E4423 or E4491).

PIT5242

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that after turning the ignition off and opening the driver's door that they can turn the radio on. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

PIT5184A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an instrument panel backlighting flashes, flickers or inoperative, unwanted horn activation, radio controls inoperative or unwanted activation, OnStar unwanted activation, and cruise control inoperative. Technician should inspect for a short to ground on the steering wheel near the Supplemental Inflatable Restraint coil connector X2 and make necessary repairs to any shorted circuits and then position the wiring.

13-00-89-004D

Service Bulletin/Repair Instructions

This informational bulletin provides an update for 13-00-89-004C to include updated information.

PIT5206A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages " Brake Pedal Override Feature ", transmission busy or frequent shifting up or down. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor.

PIT5181A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find DTCs P057C and or P057D. Some vehicles may have cruise and brake light operation service stability message with Diagnostic Trouble Codes C0161 and C0277. Technician will need to inspect connector X205 for loose, backed out, or bent terminals using the appropriate terminal test probe.

00-06-01-026E

Service Bulletin/Repair Instructions

This informational Bulletin provides a revision for 00-06-01-026D to add the 2014 model year.

PIT4376G

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician about key and theft information for Fleet Vehicles equipped with RPO 6E2 or 6E8 and converting to fleet mode. Technician will need to ensure fleet vehicles with RPO 6E2 or 6E8 should be checked to verify that the Theft Deterrent Module is in fleet mode prior to attempting to add keys.

PI0018B

Service Bulletin/Repair Instructions

This preliminary bulletin provides a pre-inspection symptom list before preforming any repairs to any of windows for noises or performance.

04-06-04-047L

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 04-06-04-047K to add the 2014 model year.

05-06-04-022J

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 04-06-04-047 to add the 2014 model year.

PI1098

Service Bulletin/Repair Instructions

This preliminary Informational bulletin provides information on Battery Test Cold Cranking Amperage (CCA) for Original Equipment Batteries and Testing Tips.

09-06-04-015B

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 09-06-04-015A to add the 2012-2014 model years.

10-08-110-001A

Service Bulletin/Repair Instructions

This informational Bulletin provides a revision for 10-08-110-001 to add the 2012-2014 model years.

130089004D

Service Bulletin/Repair Instructions

Car and Truck Fix it Right the First Time Issues

PI-0018-B

Service Bulletin/Repair Instructions

GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. *PE

PIC5932

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.

PIP5163

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIP4681D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a random bump, chuggle, or fishbite sensation when crowding the throttle slightly with the Torque Converter Clutch on while cruising at 35-60 miles per hour. Technician should follow all published Service Information diagnostics if the concern is repaired compare to a like vehicle with the same options.

PIP4568P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

PIP5161

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on a rough running engine, and/or oil consumption. Technician will find Diagnostic Trouble Code P0300 set. Technician will apply regulated air pressure through the PCV pipe and spray soapy water where the PCV baffle and valve cover meet with soapy water to inspect for possible signs of a leak. Technician will replace the value cover if a leak is present.

PIT3189R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about customers that are unable to override the automatic door locking feature. Technician will update the Body Control Module on 2006 to 2007 model years. On 2010 to 2014 model years technician will need to contact Techline Customer Support for calibrations.

PIT4116E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have power lift-gate that is inoperative from all the switches and the keyless entry transmitter only with the ignition in the off position. Technician will need to inspect circuit 5985 for battery voltage. Repair any damaged wires or terminals.

PIP4686D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have various 2-Mode Hybrid issues. Some vehicle may have service hybrid system lamp that comes on with a Diagnostic Trouble Code P061B set. Technician will need to take a snap shot of the Electronic Brake Control Module and call General Motors Technical Assistance Center for further assistance. Some vehicles may have a combination of engine stall at a stop, lacks power on acceleration, surge while driving, engine flare, transmission slip, poor or lower fuel economy or reduced EV range/limited electric propulsion since completion of recent programming. Technician will need to perform a Charge Procedure. Some vehicles have Diagnostic Trouble Code P0BBD stored without Diagnostic Trouble Code P061B or P0AFA. Technician will verify that the Drive Motor Battery was not run low on charge due to a no start concern.

PIP4765A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have Service Engine Soon Malfunction Indicator Lamp on and a constant engine misfire. If Service Information diagnosis isolates no compression on the misfiring cylinder(s) with 100% leakage into the crankcase, perform the following steps as necessary before disassembling the engine. Technician will use a lighted bore scope if available to inspect the top of the related piston(s) through the spark plug hole to determine if any of the pistons are melted. If damaged piston(s) are found inspect for aftermarket parts. Also use the latest version of 09-06-04-026 to verify if there are aftermarket calibrations in the Engine Control Module. Take photos and document accordingly if anything is found.

PIC5491D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.

PIC5492B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.

PIT5236

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492.

130089004C

Service Bulletin/Repair Instructions

Car and Truck Fix it Right the First Time Issues

130089010

Service Bulletin/Repair Instructions

PAC Courtesy Transportation Assistance Program

PIP-4686

Service Bulletin/Repair Instructions

CHEVROLET/CADILLAC/GMC: HYBRID DRIVEABILITY OR CUSTOMER CONCERNS OF FLARE, SLIP, STALL AT A STOP, SURGE, LACK OF POWER, POOR FUEL ECONOMY, REDUCED EV RANGE/LIMITED ELECTRIC PROPULSION, DTC P061B AFTER CAMPAIGN 09102B OR DTC P061B PRIOR TO CAMPAIGN. *PE UPDATED 3/14/11. *PE UPDATED 12/4/2013 *JS

PIT-4816A

Service Bulletin/Repair Instructions

CHEVROLET/GMC/CADILLAC: MULTIPLE ELECTRICAL CONCERNS WITH DTC C0900 - KEYWORDS BATTERY C/K CABLE CLOCK CRANK CYCLE DOOR DIMMING FLICKER GAGE GAUGE GMC HVAC INOP INOPERATIVE INSTRUMENT INTERMITTENT IPC LOCK NO PANEL POWER RADIO STALL START TEMPERATURE. *PE UPDATED 3/28/11. MODEL YRS 2007-2009. *PE UPDATED ON 6/27/2011 ADDED MODEL YRS 2010-2011. *KB MODEL YEARS ADDED 2012, 2013, AND 2014. UPDATED 12/2/2013*JS

PIT3237G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the percentage of UV protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces UV rays down to 4% or less. Front side door glass reduces UV rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.

PIT4816E

Service Bulletin/Repair Instructions

Diagnosing / Troubleshooting Multiple Electrical Concerns / Intermittent No Crank

PIT4817D

Service Bulletin/Repair Instructions

Intellibeam High Beam Control Testing.

PIC5491C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.

PIP5153

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the new fluids available for axle service and clarifies usage. Technician will use the chart to determine the proper axle lubricant to use.

PIT3099K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

990940005G

Service Bulletin/Repair Instructions

Seat Belt Extender Availability

PI0564D

Service Bulletin/Repair Instructions

Wax Coating on Frame Peeling, Metal Shows Corrosion/Rusting.

SB-07-02-32-002N

Service Bulletin/Repair Instructions

BUICK/CADILLAC/CHEVROLET/GMC/PONTIAC/ SATURN: THERE IS FLUID LEAKING FROM POWER STEERING SYSTEM, ALONG A FLUID LEAK IN FRONT OF VEHICLE UNDERNEATH AND SHOULD BE INSPECTED, CLEANED AND IDENTIFIED BEFORE REPAIRING OR REPLACING. MODEL 2010-14 LACROSSE, 2011-14 REGAL, 2007-14 ESCALADE, SUBURBAN, TAHOE, YUKON, YUKON XL, YUKON DENALI, YUKON DENALI XL, 2013-14 XTS, 2005-14 MALIBU, 2007-13 AVALANCHE, SILVERADO, SIERRA, 2006-10 G6, 2007-09 AURA. *PE

03-08-46-004N

Service Bulletin/Repair Instructions

This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM).

01-03-10-003K

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on GM of Canada New Vehicle Limited Warranty Tire Program and Global Warranty Management (GWM) Submission Information.

06-00-89-026L

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.

PIC5904

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.

06-06-01-010B

Service Bulletin/Repair Instructions

This informational bulletin provides information on close-coupled converter and engine replacement.

99-09-40-005G

Service Bulletin/Repair Instructions

This informational bulletin provides information on availability for the seat belt extender.

PIP4568N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

PIP4896D

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the Valve Assembly part number 24255209 and Valve Body part number 29544409 have been removed from the General Motors Product Quality Center parts restriction.

PIP4404E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.

00-03-10-003R

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information new tire warranty program and global warranty management submission information.

PIP4112M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

PIP4138N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

PIE0268

Service Bulletin/Repair Instructions

Engineering Information.

PIP4112L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

PIP5148

Service Bulletin/Repair Instructions

Tick/Ping Noise On Torque Reversal Or Load

PIT5186A

Service Bulletin/Repair Instructions

Rear Video Screens May Not Turn On

03-06-03-004I

Service Bulletin/Repair Instructions

This informational bulletin provides information for warranty codes that are generated by EL-50313 midtronics GR8 battery tester/charger.

02-07-30-029U

Service Bulletin/Repair Instructions

This informational bulletin provides information for the PQC assembly replacement process.

PI1018

Service Bulletin/Repair Instructions

This preliminary information bulletin provides information on poor or no transmitter range when using the remote keyless entry (RKE) and/or remote vehicle start (RVS).

10-00-89-010C

Service Bulletin/Repair Instructions

This informational bulletin provides information on key codes security rules and information on GM key code look up application.

13-00-89-008

Service Bulletin/Repair Instructions

This informational bulletin provides information for GM wiring repair.

10-00-89-009B

Service Bulletin/Repair Instructions

This informational bulletin provides information on key code security and information on GM key code look up applications.

130089008

Service Bulletin/Repair Instructions

GM Wiring Repair Strategy Information

130090001

Service Bulletin/Repair Instructions

Information for Engine Oils Used in 2014 Model Year Vehicles

130232001B

Service Bulletin/Repair Instructions

Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions

PI0688E

Service Bulletin/Repair Instructions

Poor Voice Quality During Bluetooth Call or OnStar® Personal Call.

PIP4568M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

PIP3119L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.

PIP5108A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an audible engine whine noise at 1500-1800 revolutions per minute. Technician will need to check the coolant level, remove serpentine belt to verify noise goes away, rotate the thermostat 90 degrees and retest, then replace thermostat and retest. Technician will replace the water pump if there is no change.

04-00-89-015E

Service Bulletin/Repair Instructions

This technical bulletin provides a revision for 04-00-89-015D to update content and incorporate the U.S. version of Bulletin 12-00-89-003.

03-00-89-006J

Service Bulletin/Repair Instructions

This technical bulletin provides a revision for 03-00-89-0061I to add the 2014 model year and Transport Mode heading.

05-09-40-002G

Service Bulletin/Repair Instructions

This technical bulletin provides a revision of 05-09-40-002F to add the 2013-2014 model years.

PIT-4954-C

Service Bulletin/Repair Instructions

GM: IF THE SERVICE SUSPENSION SYSTEM IS DISPLAYED ON THE DIC, THE TRIM HEIGHT MAY BE INCORRECT, LOOSE COMPRESSOR INLET HOSE, OR THE COMPRESSOR SELF TEST MAY BE INOPERATIVE. ALSO INCLUDED SUBURBAN LD MY 2001-2013, YUKON DENALI XL MY 2013, YUKON XL LD 2001-2013 *JS

PI0345C

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a revision for PI0345B to add the 2014 model year and update the Warranty Information.

PIP4158G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.

07-08-49-020H

Service Bulletin/Repair Instructions

This technical service bulletin provides a revision for 07-08-49-020G to add the 2014 model year and update model list.

PI0987

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information for Passenger Side Defrost Air Flow/Performance and/or Temperature Less Warm Than Drivers Side in Defrost, IP Vent or Heat Modes Condition.

12-02-32-002A

Service Bulletin/Repair Instructions

This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section.

13-02-32-001A

Service Bulletin/Repair Instructions

This technical bulletin provides a revision for 13-02-32-001 to update the models information.

130232001A

Service Bulletin/Repair Instructions

Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions

PI-0011A

Service Bulletin/Repair Instructions

GM: THE FRONT OR REAR DOOR MAY NOT OPEN FROM THE INSIDE OR OUTSIDE HANDLE, THE DOOR WILL NOT UNLOCK WITH ANY METHOD. THE PROBABLY CAUSE AN INCORRECT INSTALLATION OF A HANDLE COMPONENT. *RM UPDATED ON 7/26/2013. ALL 2014 AND PRIOR GM PASSENGER CARS AND TRUCKS. *KB

PIT4954C

Service Bulletin/Repair Instructions

Suspension.

00-05-22-002N

Service Bulletin/Repair Instructions

This informational bulletin provides information for Disc Brake Warranty Service and Procedures.

PI0011C

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a revision for PI0011C to add the 2013-2014 model years and update Warranty Information.

13-00-89-006

Service Bulletin/Repair Instructions

This informational bulletin provides information for Warranty Administration ? Changes in Powertrain Warranty Coverage Effective with 2010 Model Year.

PI0086E

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information onUnexpected Loss of Radio Audio (Radio Goes Silent/No Sound) and Other Blackberry® Phone - Bluetooth® Issues Concern.

PI0574A

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a revision for PI0574A to include the 2013-2014 model year vehicles, update the covered models and the Recommendation/Instructions section.

08-06-01-006D

Service Bulletin/Repair Instructions

This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.

11-00-89-005E

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.

13-02-32-001

Service Bulletin/Repair Instructions

This informational bulletin provides information for Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions

PI0639B

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a revision of PI0639B to add the 2013 model year and update the labor operation information.

PIP4158F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.

PIT5214

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

02-08-98-002D

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.

11-00-90-001B

Service Bulletin/Repair Instructions

This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel.

09-00-89-008A

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.

PI0592B

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a revision of PI0592A to add the 2013 and 2014 model years.

07-03-10-015C

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information.

05-08-48-001C

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor Operation.

PI0430B

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a revision of PI0430A to update the model years.

PIT5074G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

05-03-07-009F

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 05-03-07-009E to add the 2014 model year and update the Labor Operations.

13-00-89-004B

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 13-00-89-004A to include updated information.

06-00-89-026K

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 06-00-89-026J to add the 2014 model year and update the labor operations.

10-00-89-016A

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 10-00-89-016 to include the 2012-2014 model years and update the Labor Operation graphic.

09-03-16-002B

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time Code and update the tool reference information.

09-07-30-018D

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 09-07-30-018C to add the 2014 model year and update the Labor Operation.

10-00-89-005C

Service Bulletin/Repair Instructions

This informational bulletin is a revision for 10-00-89-005B to add the 2014 model year and labor codes.

11-00-89-007C

Service Bulletin/Repair Instructions

This informational bulletin is a revision for 11-00-89-007B to add the 2014 model year and update the Labor Operation List.

PI0388C

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a revision of PI0388B to add the Cadillac XTS model, graphics, improved Instructions and Warranty Information.

07-00-89-037F

Service Bulletin/Repair Instructions

This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission.

09-00-89-016C

Service Bulletin/Repair Instructions

This informational bulletin is a revision for 09-00-89-016B to add the 2014 model year and update the labor operation.

PI0718B

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a revision of PI0718A to add model years and update the Warranty Information.

03-08-48-006I

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 03-08-48-006I to add model years and update parts information.

PIT4720C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.

03-06-03-004H

Service Bulletin/Repair Instructions

This informational bulletin is a revision for 03-06-03-004G to add the 2014 model year and update the Labor Operation.

090730018D

Service Bulletin/Repair Instructions

Change in Automatic Transmission Add Condition Documentation and Claim Submission

130089004B

Service Bulletin/Repair Instructions

Car and Truck Fix it Right the First Time Issues

130232001

Service Bulletin/Repair Instructions

Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions

PI-0488

Service Bulletin/Repair Instructions

GM: THE TRANSMISSION IS SLIPPING OR HAS NO FORWARD/REVERSE MOVEMENT. *RM UPDATED 4/16/12. *PE UPDATED 6/18/12. *PE UPDATED ON 7/09/2013. *KB

PI0488C

Service Bulletin/Repair Instructions

Diagnostic Information for Transmission.

PIP-4158F

Service Bulletin/Repair Instructions

GENERAL MOTORS: LOW ENGINE OIL PRESSURE, NO OIL PRESSURE, AND/OR ENGINE NOISE. THIS COULD BE THE RESULT OF A STICKING OIL PUMP PRESSURE RELIEF VALVE. *KB

SB07-08-47-004EA

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

PIT4657F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the Multiple Diagnostic Interface or Techline computer terminal locks up during Service Programming System Sequential Programming or failed Service Programming System Sequential Programming event or no communication with any one Hybrid module. Technician will need to contact Techline customer support center for further assistance.

13-00-89-005

Service Bulletin/Repair Instructions

This technical bulletin provides Warranty Administration - New Labor Codes information.

PIP5115

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P0011 after the camshaft was replaced. Technician should check the part number on the cam that was replaced for the correct part number.

PIC4707D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have at times the XM Traffic or Weather for the local area takes several minutes to update and may read "NO DATA" or "UPDATING" during that time. Technician should be advised that Traffic and Weather data from local reporting stations and then send the updated info process may take up to 24 minutes. Technician should test for full operation of the XM band if the system has not started receiving the Traffic and weather update within 30 minutes. Also ensure the customer has not shut XM NavTraffic off in the user settings of the navigation radio. Technician will need to contact XM customer assistance to review the account status and verify that the XM Traffic option has been enabled and is available in the area.

03-06-03-003C

Service Bulletin/Repair Instructions

This technical bulletin provides a revision of 03-06-03-003B to add the 2010-2014 model years, update the Attention statement, change the terms Claim Type B to Claim Type ZPTI, GM Dealer to GM Service Agent, Repair Order to Job Card, Warranty Claim to Warranty Transaction, and to update the Procedure Information for submitting Vehicle Repairs from WINS to Global Warranty Management (GWM).

PI0564C

Service Bulletin/Repair Instructions

This preliminary information bulletin provides a revision of PI0564B to add models.

PIP5108

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an audible engine whine noise at 1500-1800 revolutions per minute. Technician will need to check the coolant level, remove serpentine belt to verify noise goes away, rotate the thermostat 90 degrees and retest, then replace thermostat and retest. Technician will replace the water pump if replacing the thermostat does not repair the audible engine whine noise.

12-04-21-001B

Service Bulletin/Repair Instructions

This technical bulletin provides a revision of 12-04-21-001A to add the 2013 model year, clarify the information from the previous bulletin and to add data throughout. The document should be reviewed and treated as new information.

99-04-20-002H

Service Bulletin/Repair Instructions

This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.

13-00-89-004

Service Bulletin/Repair Instructions

This technical bulletin provides a revision of 10-00-89-017Z to include updated information.

PIP4158E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.

PIP5104

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a cold engine tick noise for 50 seconds at start up. Technician determines if the tick noise is possibly coming from the exhaust manifold, as this noise could easily be mistaken for an engine tick noise. If your SI diagnosis does not isolate the cause of this concern, this concern should be considered a vehicle design characteristic of the ECM calibration and no additional repairs should be performed.

PI0572B

Service Bulletin/Repair Instructions

This preliminary information bulletin is for information on COAX Repair Kit Availability. Revised from PI0572A

120421001B

Service Bulletin/Repair Instructions

Transfer Case Identification First Design vs. Second Design

130089003

Service Bulletin/Repair Instructions

Vehicle Software Enhancements

130089004

Service Bulletin/Repair Instructions

Car and Truck Fix it Right the First Time Issues

130089004A

Service Bulletin/Repair Instructions

Car and Truck Fix it Right the First Time Issues

PIT5029

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

PIT5206

Service Bulletin/Repair Instructions

Unwanted Grade Braking, Low Power, and/or Transmission Busy Shifting.

PIT5209

Service Bulletin/Repair Instructions

Unwanted Alarm Sounding (GM Accessory Inclination Sensor Mounting)

SB12-08-132-001A

Service Bulletin/Repair Instructions

GENERAL MOTORS: ON SOME TRUCKS AND PASSENGER VEHICLES, ACCESSORY POWER OUTLETS (APO) AND TRAILER LIGHTING ARE COMMON ACCESSED ELECTRICAL SYSTEMS THAT ARE AFFECTED BY DEVICES THAT ARE PLUGGED IN AND BECOME INOPERATIVE DUE TO AN OPEN FUSE AND NO PROBLEM WITH VEHICLE IDENTIFIED. MODELS YEARS 2010-2014 TRUCKS AND PASSENGER. NO MODELS. *PE

13-00-89-003

Service Bulletin/Repair Instructions

This technical bulletin provides information on Vehicle Software Enhancements for 2014 and prior GM Passenger Cars and Light Duty Trucks.

PI0040C

Service Bulletin/Repair Instructions

This bulletin provides a procedure to replace the door panel retainers if the customers concern is a rattle noise or gap.

11-00-89-005D

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm.

12-08-132-001A

Service Bulletin/Repair Instructions

This informational bulletin provides information accessory power outlet and trailer lighting fuse replacement due to electrical systems that can be affected by devices that are plugged in by the customer.

PIP5102

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P0016 stored. Technician will need to inspect the reluctor on the crankshaft. If the reluctor has moved replace the crankshaft.

09-00-89-002H

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers to properly maintain vehicle in inventory.

PI0938

Service Bulletin/Repair Instructions

This preliminary information bulletin provides information on powertrain and various electronic/electrical control issues.

PIC5491B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

06-00-89-029I

Service Bulletin/Repair Instructions

This informational bulletin provides information on the proper cleaning products for GM hard or plastic surfaces, seats carpet, vinyl.

13-08-116-001A

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on aftermarket ALSL or DLC devices causing multiple issues due to suspected tampering.

PI0608A

Service Bulletin/Repair Instructions

This preliminary information bulletin provides information and additional diagnostics on park assist blocked being messaged on the DIC.

09-06-04-026G

Service Bulletin/Repair Instructions

This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2)

PIP5099A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have intermittent Diagnostic Trouble Code P0340. Technician will replace the cam position sensor if the vehicle build is Sept or Oct of 2012 and SI diagnostics does not lead to a resolution.

10-00-89-017Z

Service Bulletin/Repair Instructions

This informational bulletin provides information on fix it right for first time issues.

PI0522D

Service Bulletin/Repair Instructions

This preliminary information bulletin provides a procedure to adjust the transmission dipstick tube and/or install the transmission fluid filler tube sleeve to eliminate a tick, buzz or rattle noise from the front of dash, transmission filler tuber cracked or broken.

PIP5099

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent Diagnostic Trouble Code P0340. Technician will need to replace the cam position sensor to correct this Diagnostic Trouble Code P0340 concern.

00-03-10-002G

Service Bulletin/Repair Instructions

This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.

PI0534B

Service Bulletin/Repair Instructions

This preliminary information bulletin provides a procedure to eliminate a whine noise that varies with engine speeds.

1308116001A

Service Bulletin/Repair Instructions

Aftermarket ALDL or DLC Interface Devices Causing Multiple Issues

PI0412B

Service Bulletin/Repair Instructions

No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.

PIT4474D

Service Bulletin/Repair Instructions

Navigation or Radio Display Blank Or Flashing DTC B1265 B1288 Or B1289.

PIT4821C

Service Bulletin/Repair Instructions

High Voltage 2-Mode Battery Parts Restriction-TAC.

PIP3140E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.

PIP5003C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a service four wheel drive message displayed in the driver?s information center. Technician may find Diagnostic Trouble Code C0387. Technician should follow published Service Information diagnostics for the Diagnostic Trouble Code if it is a current code. Technician will need to attempt to duplicate the concern if the Diagnostic Trouble Code is set history. If the customer experiences repeat occurrences of this condition and a root cause cannot be determined, it is probable that the transfer case encoder motor is not responding quickly enough and should be replaced.

PIP5094

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.

PIP4819A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have Service Engine Soon Malfunction Indicator Lamp and the engine misfires. Technician may find Diagnostic Trouble Codes P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, and P0308. Technician will need to inspect the spark plug wires. Technician will need to replace any loose spark plug wires.

PIP3119K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.

120232001A

Service Bulletin/Repair Instructions

Hydraulic Power Steering Leak at Hose Connection to Steering Rack

120601007A

Service Bulletin/Repair Instructions

New Service Cam Bearings For Gen IV V8 Engines

PIP5089

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code C0569 that will not clear. Technician should be advised if there are any issues with the rotational position sensor, incremental position sensor, encoder motor, motor A or B circuits, rotational position sensor or incremental position sensor circuits when the transfer case control module attempts to determine location the location cannot be determined correctly.

PIT4605D

Service Bulletin/Repair Instructions

Cold Air Leak On Passenger Floor.

00-03-10-006I

Service Bulletin/Repair Instructions

This informational bulletin provides information on tire radial force variation.

02-07-30-029T

Service Bulletin/Repair Instructions

This informational bulletin provides information on the replacement process for the product quality center.

08-08-48-003G

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure for adding double sided tape on the right and left windshield side reveal moldings to remove tapping, clicking or ticking type noise.

12-07-30-001B

Service Bulletin/Repair Instructions

This informational bulletin provides information for service agents not required to contact product quality center for CNG, LPG or gasoline engine, transmission and/or transfer case.

13-08-116-001

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on suspected tampering due to aftermarket ALDL or DLC interface devices causing multiple issues.

09-06-04-026F

Service Bulletin/Repair Instructions

This informational bulletin provides information on suspected tampering on vehicles modifications for identifying non GM ECM calibrations.

PIP5087

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a service 4WD message displayed in the Driver Information Center. Technician may find Diagnostic Trouble Code C0379. Technician will need to inspect the front axle actuator connector for signs of moisture intrusion. If there is corrosion on the terminals at either location replace the actuator and harness.

PI0534A

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information on dignostics for a whine noise at varies engine speeds.

08-08-51-002A

Service Bulletin/Repair Instructions

This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.

03-00-89-013H

Service Bulletin/Repair Instructions

This informational bulletin provides information on a update for the Electronic Component Exchange Program (U.S. and Canada Only)

PIP4138M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

PIT5195

Service Bulletin/Repair Instructions

Speedometer Needle Accuracy Information

PIP4138L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

11-00-90-001A

Service Bulletin/Repair Instructions

This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils.

PIP4600C

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that 2ML70 Transmission Assembly will be placed on a parts restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.

11-00-89-005C

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm

PIC5687C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that loose connection between the vehicle and a Bluetooth phone. Technician will need to use a scan tool to check the "Firmware Over-the-Air" value. If the "Firmware Over-the-Air" value is up to date and customer's concern is still present contact General Motors Technical Assistance Center for further assistance.

PIC5492A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.

PI0876

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information on replacing the transmission fluid level indicator if a customers comments regarding one being broken.

PIT4543A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the puddle light operation. Technician should be advised that the puddle lamps to operate, "Approach Lighting" must be turned on using the Drivers Information Center buttons.

PIT3173C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.

PIT3271F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

10-00-89-017X

Service Bulletin/Repair Instructions

This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.

PI0774B

Service Bulletin/Repair Instructions

This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation settings for concernc regarding noice drop outs during calls and muffled sound.

PIT4911T

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.

120310003

Service Bulletin/Repair Instructions

Diagnostic Tips for Difficult to Resolve Tire/Wheel Vibration Concerns

SB-12-03-10-003

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

08-08-46-004A

Service Bulletin/Repair Instructions

This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.

080846004A

Service Bulletin/Repair Instructions

This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.

PIT5019A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have the front seats will not cool when using remote vehicle start. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

PIT3330F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about customers may inquire about the availability of the passenger compartment air filter. Dealer should advise the customer starting in 2003 the passenger compartment air filter is no longer available as a factory option.

PIT4261C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

00-00-89-027G

Service Bulletin/Repair Instructions

This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.

000089027G

Service Bulletin/Repair Instructions

This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.

PIC4310H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

PIC4801E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.

PIT4733J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.

PIT4505F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a rattle, buzz, tick, or vibration type noise that appears to be coming from the center of the dash. Technician will adjust the transmission dipstick tube away from the front of cowl to provide additional clearance.

12-03-10-002

Service Bulletin/Repair Instructions

This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles

120310002

Service Bulletin/Repair Instructions

This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles

PIP3720D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.

PIC5687B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that loose connection between the vehicle and a Bluetooth phone. Technician will need to use a scan tool to check the "Firmware Over-the-Air" value. If the "Firmware Over-the-Air" value is up to date and customer's concern is still present contact General Motors Technical Assistance Center for further assistance.

PIT4979C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a buzz or rattle type noise during light acceleration around 1200-2000 Revolutions per minute. Technician will need to reposition the fuel line and bracket down away from the floor pan.

06-00-89-026J

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.

060089026J

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.

PIT4383N

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the Electronic Brake Control Module and Brake Pressure Modulator Valve for the 2-Mode Hybrid Utilities and Trucks will be placed on a parts restriction through the General Motors Technical Assistance Center. Dealer will need to contact for further assistance.

PIT4585E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a no crank condition after the vehicle has had very low accessory battery voltage or a dead battery condition. Technician may find Diagnostic Trouble Code P0C76 set. Technician should be advised that anytime a battery charger or booster pack is connected to the 12 volt battery, the ignition key should always be in the off position. If a battery charger or booster pack is connected to the 12 volt battery with the ignition key on tech will need to reset the Hybrid Powertrain Control Module Diagnostic Trouble Codes.

PIT4041D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the power lift gate Regular Production Option Code (E61 or TB5) is inoperative. Technician will find Diagnostic Trouble Code B153A set in the power lift gate control module. Technician will need to perform these steps. 1. Disconnect the connector at the Lift gate Latch Assembly. 2. Install a 3 ampere fused jumper wire between each signal circuit and the ground circuit. 3. If either test fails, check the wiring for the signal circuits, low reference circuit, or try a power lift gate control module from a known good vehicle. 4. If both tests pass, monitor the internal switch inputs in the lift gate latch assembly for proper operation. 5. If one of the internal lift gate latch assembly switch inputs are not reading correctly in one of the positions above and the vehicles passes test both test, replace the Lift Gate Latch Assembly.

PIT4593D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a lack of brake assist after disconnecting the battery or after the 12 volts battery has run low on voltage. The Antilock Braking System Malfunction Indicator Lamp may also be on. Technician may find Diagnostic Trouble Code C121D sym 00 or C056D sym 00 set in the Electronic Brake Control Module. Technician should be advised to wait for a period of at least 1 minute with the ignition in the "OFF" position prior to disconnecting the negative battery cable. Technician will need to follow these steps to repair the concern. 1. Install the negative battery cable to the battery. 2. Rotate the lever lock clockwise until an audible click is heard in order to connect the negative battery cable to the battery. 3. Position the negative battery cable insulating cover over the negative terminal. 4. Start the vehicle without stepping on the brake pedal. 5. Shut the vehicle "Off" for one minute. 6. Restart vehicle and check brakes for proper operation. 7. Clear codes in the Engine Control Module and the Electronic Brake Control Module.

PIT4600E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about Electronic Brake Control Module relearn procedure is required anytime the Electronic Brake Control Module is replaced or has been Service Programming System reprogrammed.

10-00-89-010B

Service Bulletin/Repair Instructions

This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.

100089010B

Service Bulletin/Repair Instructions

This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.

120089002A

Service Bulletin/Repair Instructions

This informational bulletin provides information for requesting a new key code for customers with lost or stolen keys

01-00-89-010J

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.

010089010J

Service Bulletin/Repair Instructions

This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.

10-00-89-017W

Service Bulletin/Repair Instructions

This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.

100089017W

Service Bulletin/Repair Instructions

This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.

030846004M

Service Bulletin/Repair Instructions

This informational bulletin provides information on part restriction and ordering process information for onstar vehicle communication interface modules.

PIT4907A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

10-08-64-002B

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork

100864002B

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork

11-06-04-007C

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set.

PI0695A

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to properly mount and balance wheels and tires on heavy duty truck models only

PIT4163E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that only have audio from the front left speaker after replacing the amplifier. Technician should program the amplifier using Tis-2-Web using Service Programming System with the latest calibrations.

PIT4208D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a power steering pump whine noise. Technician will need to flush and refill the power steering system with Lucas Power Steering Fluid with Conditioners. Technician will replace the power steering pump with the latest design if the fluid is not available.

PIT4225F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an Antilock Braking System lamp followed by a Service Stability message in the Drivers Information Center. Technician my find Diagnostic Trouble Code C0710 set in the Electronic Brake Control Module. Technician may or may not find Diagnostic Trouble Code C0455. Technician will need to ensure the steering wheel is properly installed to the steering shaft.

PIT5014A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a front passenger flooring wet, water sloshing noise, and/or mist from the dash vents. Technician will need to rotate the drain hose to clear the heat shield.

PI0688D

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a procedure to replace the mobile microphone for concerns regarding poor voice quality during bluetooth call or onstar personal calls.

PIT4937B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the rear power lift-gate is inoperative with the inside switch and the outside door handle. Dealer should advise the customer to press the unlock button on the door panel and the lift-gate will work.

PIT4979B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a buzz or rattle type noise during light acceleration around 1200-2000 Revolutions per minute. Technician will need to reposition the fuel line and bracket down away from the floor pan.

PIT4874B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B0081 in the Sensing and Diagnostic Module and Passenger Presence Sensor modules. Technician should inspect the Sensing and Diagnostic Module and Passenger Presence Sensor powers, grounds, and communication circuits at all in line connectors for fully seated, backed out terminals, and proper terminal tension using the correct test probes.

PIC4935D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.

PIC5491A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

PIT4169F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a "Service Stability Message" appears on the Drivers Information Center. Technician will find Diagnostic Trouble Code C0561 set in the Electronic Brake Control Module. Technician will need to address any other Diagnostic Trouble Codes that are set in the vehicle first before working on Diagnostic Trouble Code C0561.

PIT3078F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have grease leaking from front hub bearings. Technician should not replace the bearing for grease purge. Technician should be advised to not clean the purged grease from the area immediately on or adjacent to the seals because this grease provides additional protection. Technician should only replace the bearing if the seals show visible damage, bearing endplay is greater than 0.005" or 0.13mm, bearing exhibits rough rotation, or bearing exhibits abnormal noise.

PIT4089H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are unable to set a personalized easy exit seat and/or power tilt column position and they will only move a predetermined amount. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

PIT3099J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

PI0086D

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a list of corrections for multiple concerns regarding Unexpected Loss of Radio Audio (Radio Goes Silent/No Sound) and Other Blackberry Phone - Bluetooth Issues

09-06-04-026E

Service Bulletin/Repair Instructions

This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2 or GDS 2

09-07-30-018C

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions

12-00-89-007

Service Bulletin/Repair Instructions

This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.

PI0373A

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions.

PIT5185

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that if the ignition key is turned to the start position, and then released when the engine begins cranking, the engine will continue cranking for a few seconds or until the vehicle starts. Some customers may state that this feature is inoperative. Technician should be advised that if the Low Fuel warning lamp is on and/or the FUEL LEVEL LOW message is displayed in the Driver Information Center, the Computer?Controlled Cranking System will be disabled.

PIT3237F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces Ultraviolet rays down to 4% or less. Front side door glass reduces Ultraviolet rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.

PIT5184

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an instrument panel backlighting flashes, flickers or inoperative, unwanted horn activation, radio controls inoperative or unwanted activation, OnStar unwanted activation, and cruise control inoperative. Technician should inspect for a short to ground on the steering wheel near the Supplemental Inflatable Restraint coil connector X2 and make necessary repairs to any shorted circuits and then position the wiring.

PIC5759

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.

11-00-89-005B

Service Bulletin/Repair Instructions

This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm

07-00-89-037E

Service Bulletin/Repair Instructions

This warranty administrational bulletin provides information on courtesy transportation and roadside assistance programs offered through GM.

10-00-89-017V

Service Bulletin/Repair Instructions

This informational bulletin provides information on newly release bulletins used to fi the vehicles in the field the first time.

PIT5170

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the front and/or rear heated seats are inoperative and/or the driver's power seat only moves in short bursts each time the seat switch is operated. Technician will need to reprogram only the affected module (Memory Seat Module, Rear Heated/Vented Seat Module, or Front Seat Heating Control Module) with updated calibrations in Tis-2-Web.

090730018C

Service Bulletin/Repair Instructions

Warranty Administration ? Change in Automatic Transmission Add Condition Documentation and Claim Submission

PI0822

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

PIC5588A

Service Bulletin/Repair Instructions

Programming And Activation Of Replacement OnStar Modules.

PIT4508C

Service Bulletin/Repair Instructions

Cruise Control Inoperative.

PIT4322F

Service Bulletin/Repair Instructions

Unwanted Stability Activation And/Or C0710.

PIT4911S

Service Bulletin/Repair Instructions

Navigation Radio Radio And Integrated Center Stack

PIT5179

Service Bulletin/Repair Instructions

Cruise Control Inoperative.

PIT5180

Service Bulletin/Repair Instructions

Whistle Noise From Drivers Side A Pillar Area

PI-0773

Service Bulletin/Repair Instructions

CADILLAC/CHEVROLET/GMC/HUMMER/PONTIAC: THERE IS SLIPPING OR HAVE NO FOURTH, FIFTH OR SIXTH GEAR AND MALFUNCTION INDICATOR LAMP (MIL) WOULD BE ON, WITH DIAGNOSTIC TROUBLE CODE (DTC) P0796 FOUND AS ACTIVE. *PE

PI0522B

Service Bulletin/Repair Instructions

GM: TICK OR RATTLE NOISE FROM FRONT OF DASH, TRANSMISSION FILLER TUBE CRACKED OR BROKEN (INSPECT FILLER TUBE, REPLACE TUBE AS NECESSARY). *JS UPDATED 05/3/2013 *JS

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.

2012 Cadillac Escalade Service Bulletins: 1318 bulletins | CarFathom