Vehicle report

2019 CHEVROLET SUBURBAN

Service bulletins

737 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

PIP4902W

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIT5099J

Service Bulletin/Repair Instructions

PI to help diagnose A/C concern

PIT5509N

Service Bulletin/Repair Instructions

This PI provides diagnostic tips for diagnosing electric trailer brakes issues.

PIT5509M

Service Bulletin/Repair Instructions

This PI provides diagnostic tips for diagnosing electric trailer brakes issues.

PIT3271Q

Service Bulletin/Repair Instructions

This preliminary information communicates information about how to determine if a wheel and tires size change is available.

PIP4902V

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIP6104

Service Bulletin/Repair Instructions

This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical Assistance Case in CX Connect.

PIT6425D

Service Bulletin/Repair Instructions

This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no DTC'ss

PIT6483

Service Bulletin/Repair Instructions

This preliminary information communicates an issue with aftermarket LED headlights causing IPC warning messages and MIL along with several low speed lan DTCs.

PIT6400A

Service Bulletin/Repair Instructions

This PI Communications information on an alternative product dealers can use to perform 19-NA-255: Wax Coating on Frame Peeling, Metal Shows Corrosion/Rusting due to issue with getting product from current supplier listed in the bulletin.

PIT6425C

Service Bulletin/Repair Instructions

This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no DTC's

PIP4902U

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIT5984A

Service Bulletin/Repair Instructions

This Preliminary information communicates a diagnostic tip for an issue where the starter stays engaged after the engine starts. Dealers are to suspect/monitor the crankshaft position sensor.

PIT5214G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer’s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

PIT6425B

Service Bulletin/Repair Instructions

This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no DTC's

PIT6425A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no DTC's

13598

Other

New Vehicle Monitoring Programs Section in IVH

PIT5479H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston.

22-NA-080

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of engine related shudder.

PIP4902T

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIC5650M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.

N252494770-01

Service Campaign

Amendments to the Song-Beverly Act (SBA) California warranty law provides vehicle owners with an opportunity to submit a written notice to GM before filing a lawsuit seeking a vehicle repurchase. If such a notice is not provided to GM, then the vehicle owner is prevented from seeking civil penalties in litigation. Vehicle owners of the affected vehicles will be mailed an owner’s manual and warranty insert containing this information in English and Spanish.

PIC6086J

Service Bulletin/Repair Instructions

This PI communicates a procedure to clean oil leaking from the rain sensor.

N252494770

Service Campaign

Amendments to the Song-Beverly Act (SBA) California warranty law provides vehicle owners with an opportunity to submit a written notice to GM before filing a lawsuit seeking a vehicle repurchase. If such a notice is not provided to GM, then the vehicle owner is prevented from seeking civil penalties in litigation. Vehicle owners of the applicable vehicles will be mailed an owner’s manual and warranty insert containing this information in English and Spanish.

PIT6400

Service Bulletin/Repair Instructions

This PI Communications information on an alternative product dealers can use to perform 19-NA-255: Wax Coating on Frame Peeling, Metal Shows Corrosion/Rusting due to issue with getting product from current supplier listed in the bulletin.

PIT6180A

Service Bulletin/Repair Instructions

This Preliminary information communicates assistance in locating the Rear seat belt comfort guides in the parts catalog.

PIP4902S

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

25-NA-156

Service Bulletin/Repair Instructions

This service bulletin provides information on Tire Sidewall Irregularities.

00-06-01-026R

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

PIT5074R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.

23-NA-153

Service Bulletin/Repair Instructions

The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

15-NA-010

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.

25-NA-100

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on vehicles outside of a California Emissions State who move to and register their vehicle in a California Emission State may be entitled to the 7 year, 70,000-mile Emission Select State Component Limited Warranty.

PI0281L

Service Bulletin/Repair Instructions

This preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when addressing underbody component corrosion with customers.

PIT5551R

Service Bulletin/Repair Instructions

This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting.  This is normal when the FAB has been set to  "Alert".

07-00-89-037W

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

18-NA-315

Service Bulletin/Repair Instructions

This service bulletin advises the tech to only replace the shock that is bad and not all shocks.

25-NA-087

Service Bulletin/Repair Instructions

This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use for certain repairs, such as Wiring Harness Repairs.

13-08-116-001K

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

25-NA-052

Service Bulletin/Repair Instructions

This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.

24-NA-098

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.

25-NA-065

Service Bulletin/Repair Instructions

This informational bulletin instructs the tech when fuel/fluid is needed to be tested and where it can be sent for analysis.

PIT5511F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure.  This is done to protect the Driver Information Center from damage.

08-03-10-006I

Service Bulletin/Repair Instructions

This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.

15-06-03-001F

Service Bulletin/Repair Instructions

This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.

19-NA-255

Service Bulletin/Repair Instructions

This service bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

17-NA-073

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding the field action courtesy transportation policy.

05-03-07-009L

Service Bulletin/Repair Instructions

This service bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles.

11-00-89-005Y

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

05-08-51-001L

Service Bulletin/Repair Instructions

This informational bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.

PIP5358D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

16-NA-109

Service Bulletin/Repair Instructions

This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.

PIT5551Q

Service Bulletin/Repair Instructions

This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting.  This is normal when the FAB has been set to  "Alert".

07-00-89-037V

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

PIT5479G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

PIP5175F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.

10-08-110-001L

Service Bulletin/Repair Instructions

This service bulletin provides information on proper use of floor mats.

21-NA-043

Service Bulletin/Repair Instructions

This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.

22-NA-074

Service Bulletin/Repair Instructions

This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

22-NA-244

Service Bulletin/Repair Instructions

This warranty administration service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.

21-NA-135

Service Bulletin/Repair Instructions

This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content.

01-08-42-001Q

Service Bulletin/Repair Instructions

This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.

24-NA-173

Service Bulletin/Repair Instructions

This bulletin advises the technician that if the code sets, verify the sensor then inspect the engine oil pump for a sticking valve that may cause the MIL to illuminate.

09-06-04-026Z

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

22-NA-218

Service Bulletin/Repair Instructions

This informational bulletin advises the technician on normal noises produced by the engine and to explain this to the customer.

20-NA-166

Service Bulletin/Repair Instructions

This service bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.

20-NA-132

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.

07-00-89-037U

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

03-06-01-023I

Service Bulletin/Repair Instructions

This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.

18-NA-263

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).

PIT5074Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIT5962B

Service Bulletin/Repair Instructions

This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.

PIT6261

Service Bulletin/Repair Instructions

This Preliminary information communicates to dealers GM is working on a solution for outdated Apps

08-07-30-035I

Service Bulletin/Repair Instructions

This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.

19-NA-219

Service Bulletin/Repair Instructions

This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.

04-06-01-029K

Service Bulletin/Repair Instructions

This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.

PIP4723J

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIT5698E

Service Bulletin/Repair Instructions

This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.

PIT5569C

Service Bulletin/Repair Instructions

This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.

PIP6015

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM technical assistance case using the dealer case management tool.

24-NA-040

Service Bulletin/Repair Instructions

This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.

10-00-89-009F

Service Bulletin/Repair Instructions

This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).

03-06-01-023H

Service Bulletin/Repair Instructions

This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.

01-06-01-011Q

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

PIP5621E

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer  technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.

99-00-89-019Z

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.

07-00-89-037T

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

23-NA-154

Service Bulletin/Repair Instructions

This bulletin provides information on Warranty Administration – Required Operating Procedures - 8 Points (U.S. Only).

PIT5551P

Service Bulletin/Repair Instructions

This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting.  This is normal when the FAB has been set to  "Alert".

04-06-04-051J

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

23-NA-219

Service Bulletin/Repair Instructions

This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.

20-NA-138

Service Bulletin/Repair Instructions

This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

08-07-30-026I

Service Bulletin/Repair Instructions

This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

18-NA-146

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).

PIT5282G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness.  Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).

PIT5511E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure.  This is done to protect the Driver Information Center from damage.

PIT5099H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIC6086H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area.  Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.

PIT5509L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

PIT6212

Service Bulletin/Repair Instructions

This Preliminary information communicates an issue with the Hydrastar Electric Over Hydraulic trailer brake system causing a voltage spike into the trucks electrical system which is causing DTC C1114 to set.

07-00-89-036K

Service Bulletin/Repair Instructions

This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.

02-00-89-002X

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).

23-NA-142

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure for the techs to replace the forward check ball and separator plate if found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.

PIC5650L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

PIT3271P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIT5990B

Service Bulletin/Repair Instructions

This Preliminary information communicates an issue with a wind noise while driving at highway speeds and dealers are to inspect the body harness pass through for being full seated into the cowl.

24-NA-174

Service Bulletin/Repair Instructions

The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.

General Communication

Service Campaign

Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.

05-03-08-002J

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.

18-NA-073

Service Bulletin/Repair Instructions

This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

23-NA-044

Service Bulletin/Repair Instructions

This service bulletin provides information on AGM batteries that require less frequent charging in storage.

PIT5481J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Starting with 2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.

PIP5569B

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.

PIT5195H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

PIT6180

Service Bulletin/Repair Instructions

This Preliminary information communicates assistance in locating the Rear seat belt comfort guides in the parts catalog.

01-00-89-010S

Service Bulletin/Repair Instructions

This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

07-06-01-016J

Service Bulletin/Repair Instructions

This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

23-NA-141

Service Bulletin/Repair Instructions

This informational bulletin advises the technician that the engine and related parts will be debited if found that the tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.

00-06-01-012N

Service Bulletin/Repair Instructions

This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

05-06-04-022V

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

16-NA-222

Service Bulletin/Repair Instructions

This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.

09-06-04-026Y

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

01-06-01-011P

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

24-NA-147

Service Bulletin/Repair Instructions

This service bulletin provides information on regular inspection of the Seat Belt Lap Anchor.

18-NA-306

Service Bulletin/Repair Instructions

This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).

PI0754G

Service Bulletin/Repair Instructions

This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.

16-NA-158

Service Bulletin/Repair Instructions

This service bulletin describes the U.S. Dealer Special Tool Loan Program process.

18-NA-279

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on the process to disable and enable passive unlocking.

12-01-37-001G

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.

24-NA-141

Service Bulletin/Repair Instructions

GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.

20-NA-038

Service Bulletin/Repair Instructions

This informational bulletin explains the difference in AFM and DFM engines and what is and is not activated during this occurrence.

00-03-10-002M

Service Bulletin/Repair Instructions

This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.

17-NA-157

Service Bulletin/Repair Instructions

This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter.

99-04-20-002O

Service Bulletin/Repair Instructions

This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.

04-06-04-051I

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

16-NA-383

Service Bulletin/Repair Instructions

This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

22-NA-070

Service Bulletin/Repair Instructions

This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part replacements.

18-NA-099

Service Bulletin/Repair Instructions

This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.

22-NA-018

Service Bulletin/Repair Instructions

This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only).

19-NA-218

Service Bulletin/Repair Instructions

This service bulletin provides a service procedure to correct a condition of a Ticking Noise from the Engine.

18-NA-125

Service Bulletin/Repair Instructions

This service bulletin provides information for engine oil life monitor operation calculation.

21-NA-068

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.

20-NA-016

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.

08-07-30-035H

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

19-NA-136

Service Bulletin/Repair Instructions

This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.

16-NA-119

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.

09-00-89-008G

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

18-NA-067

Service Bulletin/Repair Instructions

This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.

22-NA-106

Service Bulletin/Repair Instructions

This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires.

06-00-89-029V

Service Bulletin/Repair Instructions

This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

10-08-110-001K

Service Bulletin/Repair Instructions

This service bulletin provides information on proper use of floor mats.

13-08-116-001J

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

15-00-89-004G

Service Bulletin/Repair Instructions

This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

23-NA-125

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Over The Air (OTA) and In Market Enhancement (IME) FAQs.

00-03-10-006P

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).

17-NA-052

Service Bulletin/Repair Instructions

This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed.

10-08-45-001H

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.

23-NA-103

Service Bulletin/Repair Instructions

This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC).

07-00-89-037S

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

11-00-89-005X

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

PIP5596A

Service Bulletin/Repair Instructions

This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.

PIT5448J

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

PIT4322P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

PIT5551N

Service Bulletin/Repair Instructions

This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting.  This is normal when the FAB has been set to  "Alert".

19-NA-044

Service Bulletin/Repair Instructions

This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.

PIT5479F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

16-NA-338

Service Bulletin/Repair Instructions

This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

PIT4506G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks and Utilities may ask if they can lower their tire pressures. Tire pressures being set to the "Tire and Loading Label" will ensure the safe handling and ride characteristics of the truck and should not be lowered.

PIT6122

Service Bulletin/Repair Instructions

This Preliminary information communicates to dealers of a known issue with failed map update

PI0281K

Service Bulletin/Repair Instructions

This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

02-08-42-001J

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.

PI1394B

Service Bulletin/Repair Instructions

This PI bulletin advises the technician on the proper way to install the pistons in an engine.

PIP5601B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

PI0592I

Service Bulletin/Repair Instructions

This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

PIT5074P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIT5962A

Service Bulletin/Repair Instructions

This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.

PIT5214F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

PIT5551M

Service Bulletin/Repair Instructions

This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting.  This is normal when the FAB has been set to  "Alert".

03-00-91-001I

Service Bulletin/Repair Instructions

This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.

20-NA-159

Service Bulletin/Repair Instructions

This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).

22-NA-225

Service Bulletin/Repair Instructions

This information bulletin advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by Rear of Transmission or Transfer Case Area.

05-00-89-029F

Service Bulletin/Repair Instructions

This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.

01-06-01-011O

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

17-NA-170

Service Bulletin/Repair Instructions

This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.

99-00-89-019Y

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.

02-00-89-002W

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).

10-00-89-006J

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIT5099G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIT5698D

Service Bulletin/Repair Instructions

This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.

07-08-49-020R

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

20-NA-142

Service Bulletin/Repair Instructions

This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving.

PIT5551L

Service Bulletin/Repair Instructions

This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting.  This is normal when the FAB has been set to  "Alert".

PIP5621D

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer  technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.

09-00-89-016H

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.

PIP5628G

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

15-00-89-004F

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

01-00-89-010R

Service Bulletin/Repair Instructions

This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

04-06-04-051H

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

03-06-01-023G

Service Bulletin/Repair Instructions

This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.

09-06-04-026X

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

17-NA-066

Service Bulletin/Repair Instructions

This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.

PIP5358C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

PIT5551K

Service Bulletin/Repair Instructions

This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting.  This is normal when the FAB has been set to  "Alert".

21-NA-026

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.

99-09-40-005I

Service Bulletin/Repair Instructions

This service bulletin provides information on availability for a seat belt extender.

PIP4902R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

01-06-01-011N

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

99-08-51-001F

Service Bulletin/Repair Instructions

This service bulletin provides information on Paintless Dent Repair Process.

13-08-116-001I

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

PIT4261J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

04-07-30-013E

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.

02-00-89-002V

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

08-07-30-026H

Service Bulletin/Repair Instructions

This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

12-03-10-001E

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

PIT5509K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

PIT3665M

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.

PIC5650K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

01-08-42-001P

Service Bulletin/Repair Instructions

This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.

11-00-89-005W

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

PIT5509J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

PIP5628F

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

12-03-10-001D

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

04-00-89-015Z

Service Bulletin/Repair Instructions

This bulletin provides information on Warranty Administration – Required Operating Procedures - 8 Points (U.S. Only).

08-07-30-035G

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

10-08-110-001J

Service Bulletin/Repair Instructions

This service bulletin provides information on proper use of floor mats.

11-00-89-005V

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

PI0281J

Service Bulletin/Repair Instructions

This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

00-06-01-012M

Service Bulletin/Repair Instructions

This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

00-06-01-026Q

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

22-NA-009

Service Bulletin/Repair Instructions

This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.

07-06-01-016I

Service Bulletin/Repair Instructions

This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

15-06-01-002O

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

16-NA-130

Service Bulletin/Repair Instructions

This service bulletin provides information for after installation of a replacement upper valve body, the transmission may have no Reverse and no 2nd gear.

15-NA-017

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.

PIT5551J

Service Bulletin/Repair Instructions

This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting.  This is normal when the FAB has been set to  "Alert".

PI0754F

Service Bulletin/Repair Instructions

This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.

99-04-20-002N

Service Bulletin/Repair Instructions

This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.

PIT4322N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

01-08-42-001O

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

15-06-01-002N

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

PIT5391F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.

PIP5628E

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

00-00-90-002M

Service Bulletin/Repair Instructions

This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.

07-03-16-004E

Service Bulletin/Repair Instructions

This service bulletin provides information for tire pressure monitoring (TPM) system concerns.

N212338810-02

Service Bulletin/Repair Instructions

Service Update. On certain vehicles equipped with a 6.0L gasoline engine (RPO L96) and is a fleet government vehicle (RPO GAM), the left rear middle body mount may crack and collapse causing a metal-to-metal contact. Dealers are to inspect the integrity of 10 resistance spot welds attaching the body mount internal reinforcement to the vehicle floor forward of the left rear wheel. In addition, an external reinforcement will be MIG stitch welded to the outer (under-car) side of the vehicle at the body mount area.

02-00-89-002U

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

15-06-01-002M

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

22-NA-257

Service Bulletin/Repair Instructions

This service bulletin provides information on Dealer Installed LPO Wheel Installation and Return Process.

09-00-89-008F

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

PIP5540J

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

21-NA-124

Service Bulletin/Repair Instructions

This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

PIT5746C

Service Bulletin/Repair Instructions

This Preliminary information communicates information on how dealers can contact the supplier for Associated Accessories offered through GM.

PIT5551H

Service Bulletin/Repair Instructions

This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting.  This is normal when the FAB has been set to  "Alert".

PIP5632G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIP4902Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIT3271N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

22-NA-216

Service Bulletin/Repair Instructions

This bulletin advises the technician to Inspect the position of the head gasket locating tabs to determine if the head gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running Hot.

PIT5481H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Starting with 2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.

22-NA-205

Service Bulletin/Repair Instructions

This service bulletin provides information on Module Harvesting.

PIP5175E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.

PIT3665L

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.

10-00-89-006I

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

99-00-89-019X

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.

PIP5882

Service Bulletin/Repair Instructions

This Preliminary information communicates diagnostic aid to help isolate possible repeat thermal by-pass valve concern.

PIC5453D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

22-NA-185

Service Bulletin/Repair Instructions

This informational bulletin explains how the trans slip or flare can be a normal condition.

22-NA-195

Service Bulletin/Repair Instructions

This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.

PIT5698C

Service Bulletin/Repair Instructions

This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.

PI0592G

Service Bulletin/Repair Instructions

This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

21-NA-077

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Aero Shutter Related Diagnostic Codes.

PIP5429A

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

05-06-04-022T

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

06-00-89-031H

Service Bulletin/Repair Instructions

This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.

07-06-01-016H

Service Bulletin/Repair Instructions

This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

13-08-116-001H

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

15-00-89-004E

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

01-00-89-010Q

Service Bulletin/Repair Instructions

This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

05-00-89-072F

Service Bulletin/Repair Instructions

This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.

09-06-04-026W

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

PIP5621C

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer  technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.

00-06-01-012L

Service Bulletin/Repair Instructions

This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

01-06-01-011M

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

04-06-04-051G

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

00-06-01-026P

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

11-00-89-005U

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

05-00-89-029E

Service Bulletin/Repair Instructions

This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.

22-NA-181

Service Bulletin/Repair Instructions

This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.

PIP5640A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

03-06-01-023F

Service Bulletin/Repair Instructions

This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.

11-00-89-005T

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

20-NA-065

Service Bulletin/Repair Instructions

This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

21-NA-199

Service Bulletin/Repair Instructions

This informational bulletin advises the technician to replace the TBV if the transmission has any type of repair even if no problem was found, to replace the tbv.

04-00-89-015X

Service Bulletin/Repair Instructions

This bulletin provides information on Warranty Administration – Required Operating Procedures - 8 Points (U.S. Only).

PIT5569B

Service Bulletin/Repair Instructions

This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.

PIT4261H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

PIP5212D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise. Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.

22-NA-135

Service Bulletin/Repair Instructions

This warranty admin bulletin covers information on Essential Tools that include Consumable Parts.

12-01-37-001F

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.

PIC5260F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIT5681C

Service Bulletin/Repair Instructions

This Preliminary information communicates the location of the GM Accessory Performance Brake System Rotor Specifications

PIT5448H

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

PIT5099F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIP5358B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

PIP5856

Service Bulletin/Repair Instructions

This Preliminary information communicates provides information to the technician on the use of R-99 or R-95  Renewable diesel fuel.

14-06-04-004H

Service Bulletin/Repair Instructions

This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours.

PIT5195G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

PIT5745D

Service Bulletin/Repair Instructions

This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw.

12-00-89-003B

Service Bulletin/Repair Instructions

This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).

20-NA-050

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to clear the codes and test the Tcase if found that the customer has tried to shift the t-case from 4lo to Hi gears while driving.

03-06-01-023E

Service Bulletin/Repair Instructions

This information bulletin explains how to measure for oil consumption and possible reasons for loss of oil.

PIE0693

Service Bulletin/Repair Instructions

This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Oil Leaking from Front of Engine.

PIC5260E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIT5287H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.

01-00-89-010P

Service Bulletin/Repair Instructions

This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

PIT5287G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.

PI0281I

Service Bulletin/Repair Instructions

This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

01-00-89-010O

Service Bulletin/Repair Instructions

This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

N212338810 01

Service Bulletin/Repair Instructions

Service Update. On certain vehicles equipped with a 6.0L gasoline engine (RPO L96) and is a fleet government vehicle (RPO GAM), the left rear middle body mount may crack and collapse causing a metal-to-metal contact. Dealers are to inspect the integrity of 10 resistance spot welds attaching the body mount internal reinforcement to the vehicle floor forward of the left rear wheel. In addition, an external reinforcement will be MIG stitch welded to the outer (under-car) side of the vehicle at the body mount area.

15-06-01-002L

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

PIP4670J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.

18-NA-161

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.

PIT3271M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIT5746B

Service Bulletin/Repair Instructions

This Preliminary information communicates information on how dealers can contact the supplier for Associated Accessories offered through GM.

20-NA-115

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the radio amplifier antenna if there is a condition of Poor Remote Keyless Entry (RKE) Fob or Passive Unlocking Range due to a internal concerns within the antenna.

20-NA-207

Service Bulletin/Repair Instructions

This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set.

22-NA-047

Service Bulletin/Repair Instructions

Information bulletin explains a possible coolant leak coming from the cylinder head bolt areas.

PIC6450

Service Bulletin/Repair Instructions

This Preliminary information communicates a process to correct the concern of Unable to contact OnStar after the 3G EOL on 2015-2022 model year vehicles in the United States.

PIT5692A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about how to diagnosis a battery draw that may be caused by a module back feeding voltage in the ignition relay circuits making the vehicle think it is still awake.

PIT5745C

Service Bulletin/Repair Instructions

This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw.

21NA135

Service Bulletin/Repair Instructions

This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content.

PIT3271L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

080089014G

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

22NA018

Service Bulletin/Repair Instructions

This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only).

990089019W

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.

070601016G

Service Bulletin/Repair Instructions

This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

150089004D

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

18NA067

Service Bulletin/Repair Instructions

This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.

PI0653F

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.

PIT4322M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

18NA235

Service Bulletin/Repair Instructions

This information bulletin advised the tech of possible use of low fuel quality and the possible ramifications in performance in regards to the customers concerns.

18NA073

Service Bulletin/Repair Instructions

This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

22NA012

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Stone Chip/Membrane Damage, Broken Connector and/or Sensor Retaining Tabs, and/or Paint Damage of Park Assist Sensors.

PIP4902P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIT5479E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

PIT5481G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Starting with 2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.

PIP4723F

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIP5632F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

22NA009

Service Bulletin/Repair Instructions

This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.

070316004D

Service Bulletin/Repair Instructions

This service bulletin provides information for tire pressure monitoring (TPM) system concerns.

16NA222

Service Bulletin/Repair Instructions

This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.

000090002L

Service Bulletin/Repair Instructions

This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.

050604022S

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

1308116001G

Service Bulletin/Repair Instructions

The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

19NA218

Service Bulletin/Repair Instructions

This service bulletin provides a service procedure to correct a condition of a Ticking Noise from the Engine.

PIP5811

Service Bulletin/Repair Instructions

This Preliminary information communicates to dealers an issue on remanufactured engines with part numbers 19368174  and 19368176 where the incorrect crankshaft timing gear was installed. Provides dealer with information to correct this condition.

20NA166

Service Bulletin/Repair Instructions

This informational bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.

19NA153

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM for metal.

030310007K

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires.

19NA104

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area.

030091001H

Service Bulletin/Repair Instructions

This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.

PIT5448G

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

PIT5291F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have wind whistle noise heard from the right or left rear quarter glass area when driving at highway speeds or with a cross wind. Technician will inspect the quarter glass for excessive urethane. If excessive urethane is found use a sharp knife and cut off the excessive urethane. Also the technician will install foam tape along the entire length of the tail light assembly.

PIT5245D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the blower motor may be noisy or vibrate when running. This concern will only occur when the temperatures is below 32 degrees Fahrenheit and if the blower motor is removed while still cold, ice may be found on the blower motor cage. This concern could be caused by water leaking or snow ingestion into the Heater-Vent-Air Conditioning case. Technician is to perform normal water testing diagnostics while the Heater-Vent-Air Conditioning is running, looking for water leaking past the plenum cover. If water is leaking past the cover remove the cover and install a 12x12 snow resistant screen to the fresh air intake. Reseal and install the plenum cover cap using Kent air dry sealer or equivalent.

PIT5317D

Service Bulletin/Repair Instructions

This Preliminary information communication provides information to the technician about vehicles with the rear body fuse block with a loose fuse connection. Technician will need to check terminal tension on the rear fuse block. Technician will need to replace the rear body fuse block if poor terminal tension is the issue. Technician will need to replace the appropriate terminated lead if something other than the main power buss bar has poor terminal tension.

20NA078

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the 4 5 6 clutch housing if the bushing was found worn and the cause of the customers concern.

PIT3099U

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

20NA132

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

17NA308

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of carpet damage, seat mounting stud wear through, hole in second row (Intermediate) carpet.

PIT5509H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

PIC5650J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

PIT5698B

Service Bulletin/Repair Instructions

This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.

PIP5813

Service Bulletin/Repair Instructions

This Preliminary information communicates A vehicle may have a need for  Camshaft replacement or have misfires on non AFM cylinders after the camshaft was replaced. The camshaft may have been boxed incorrectly

21NA152

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint percentage.

010842001N

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

PIT4261G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

990420002L

Service Bulletin/Repair Instructions

This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.

PIP5632E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

080730035E

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

110089002E

Service Bulletin/Repair Instructions

This service bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.

070089037Q

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

21NA124

Service Bulletin/Repair Instructions

This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

PIT5403H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

PIT5681B

Service Bulletin/Repair Instructions

This Preliminary information communicates the location of the GM Accessory Performance Brake System Rotor Specifications

18NA306

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).

070089037P

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

100089006H

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIT4322L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

PIT5746A

Service Bulletin/Repair Instructions

This Preliminary information communicates information on how dealers can contact the supplier for Associated Accessories offered through GM.

18NA279

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on the process to disable and enable passive unlocking.

20NA161

Service Bulletin/Repair Instructions

This informational bulletin advises the technician to check for a possible stuck oil pressure relief valve.

20NA159

Service Bulletin/Repair Instructions

This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).

19NA044

Service Bulletin/Repair Instructions

This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.

21NA077

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Aero Shutter Related Diagnostic Codes.

21NA109

Service Bulletin/Repair Instructions

This service bulletin provides diagnostic information for a customer concern of engine vibration.

16NA338

Service Bulletin/Repair Instructions

This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

PIT5717A

Service Bulletin/Repair Instructions

This Preliminary information communicates if the sunroof, rear sliding window, and/or wireless charging are found to be inoperative due to the F2DL and/or the F8DL fuse(s) being open.  Inspect the center console harness area at the hinge pivot point for chaffed circuits.

21NA103

Service Bulletin/Repair Instructions

This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition.

000601026N

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

21NA068

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ (U.S. Only).

050308002I

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.

PIP5654A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer technician that the valve body Part Unique Number (PUN) may contain the letter O or the number 0.

20NA038

Service Bulletin/Repair Instructions

This informational bulletin explains the difference in AFM and DFM engines and what is and is not activated during this occurrence.

18NA146

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).

020089002T

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

070089036J

Service Bulletin/Repair Instructions

This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.

PIP5799

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer technician to replace the transmission valve body on 2019-2021 10 speed transmissions to correct DTCs P2812 and P2814 setting if Service Information does not lead to root case of these DTCs.

18NA099

Service Bulletin/Repair Instructions

This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.

PIP5212C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise. Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.

PIT5745B

Service Bulletin/Repair Instructions

This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw.

110089005Q

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

1008110001I

Service Bulletin/Repair Instructions

This informational bulletin provides information on proper use of floor mats.

20NA138

Service Bulletin/Repair Instructions

This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

19NA255

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

21NA043

Service Bulletin/Repair Instructions

This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.

16NA109

Service Bulletin/Repair Instructions

This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.

150089004C

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

21NA026

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.

20NA142

Service Bulletin/Repair Instructions

This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving.

20NA212

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of IPC Gauges Inoperative or Fluctuate, No Crank, Start then Stall.

150601002K

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

010601011L

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

16NA171

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to reinstall the rear defroster tab on the rear window defogger for vehicles with the condition of rear defrosters inoperative or if one is to break during a normal repair.

PIT5479D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

17NA166

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to measure vibration and install engine mounts to correct a Rough Idle in Drive concern.

PIC6086G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area.  Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.

090604026S

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

040089015V

Service Bulletin/Repair Instructions

This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).

16NA019

Service Bulletin/Repair Instructions

This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares.

19NA136

Service Bulletin/Repair Instructions

This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.

18NA263

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).

060089031F

Service Bulletin/Repair Instructions

This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.

PIT5798

Service Bulletin/Repair Instructions

This Preliminary information communicates information regarding switching between adaptive cruise control and regulate cruise control.

20NA115

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the radio amplifier antenna if there is a condition of Poor Remote Keyless Entry (RKE) Fob or Passive Unlocking Range due to a internal concerns within the antenna.

000310002L

Service Bulletin/Repair Instructions

This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.

RFI20201112_751-

Service Bulletin/Repair Instructions

This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.

PIT3271K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

990851001E

Service Bulletin/Repair Instructions

Thins informational bulletin provides information on Paint-less Dent Repair Process.

PI0754D

Service Bulletin/Repair Instructions

This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.

20NA213

Service Bulletin/Repair Instructions

This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and PF48.

19NA116

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of pulsing, grinding, scraping noise from brakes, uneven front brake pad wear.

1308116001F

Service Bulletin/Repair Instructions

The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

050604022R

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

18NA315

Service Bulletin/Repair Instructions

This informational bulletin advises the tech to only replace the shock that is bad and not all.

060089026Q

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated (CCND) Labor Operation Numbers.

PIT5551F

Service Bulletin/Repair Instructions

This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting.  This is normal when the FAB has been set to  "Alert".

20NA207

Service Bulletin/Repair Instructions

This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set.

PIT5586E

Service Bulletin/Repair Instructions

This Preliminary information communicates a customer concern of IPC gauges inoperative or fluctuate, No Start, No Crank, SIR Light / Service Airbag Message, Service Suspension Message, Radio display blank, Steering Wheel Controls (SWC) not illuminated, Turn Signal no audible feedback, HVAC controls inoperative. During diagnostics a technician may find any of the following DTC's: B1011, B1370, B3980, U0020, U0029, U007D, U0073, U0078, U0100, U0101, U0102, U0104, U0140, U0151, U0155, U0164, U0184, U0186, U0198, U0422. Dealer is instructed to check for logic lock of Serial Data Gateway Module or for Serial Data Gateway Module X1 and X2 connectors having terminal concerns and repair as needed.

110089005P

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

18NA161

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.

20NA055

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to correct customer concerns of Instrument Panel Cluster (IPC) Gauges Inoperative, Numerous Driver information Center (DIC) Error Messages, No Brake or Electric Power Steering Assist, Transmission in Default Gear, No Reverse and/or Back Up Lights, No Daytime Running Lights (DRL), No Cruise or Adaptive Cruise and/or No Trailer Brake Lights.

20NA157

Service Bulletin/Repair Instructions

This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.

20NA112

Service Bulletin/Repair Instructions

This technical bulletin advises the technician to validate the code and reset if found the cause of the customers concern.

990089019U

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.

PIE0554C

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information from the technicians for the following conditions for the cluster.

PIT5533C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.

150089002B

Service Bulletin/Repair Instructions

This bulletin provides information to dealers regarding transportation damage repair claim submission requirements.

PIP5504F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians are referred to Torque Converter Diagnosis in SI.

PIT5311F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle?s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector with part number 23404450.

PIT3665J

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.

PIP5504E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians are referred to Torque Converter Diagnosis in SI.

PIT5509G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

PIP5740

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer an issue where a customer may have incorrectly received a notification advising of a starting syetem issue with their veihcle. Dealer advised to inspect for a legitimate issue, if one found, diagnose accordingly.

PIP5630D

Service Bulletin/Repair Instructions

This Preliminary information communicates A vehicle may have a concern of no oil pressure and/or P0521 set. the releif valve in the pump is sticking or the number 1 main bearing is damaged. Drop oil pan and confirm #1 main is spun or not.  If bearings are OK Then change oil pump.

990089019T

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.

PIT5206G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205.

PIT5564C

Service Bulletin/Repair Instructions

This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set.

19NA010

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Head-Up Display (HUD) on Vehicles Model Year 2017 and Newer Having Rotational Feature that Allows for Adjusting of Angle of HUD Image.

PIP5175D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.

PIP5573C

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer technician that the torque converters for the 10L80 and 10L90 10 speed transmission are on restriction through the Product Quality Center. Dealers are advised to contact the Product Quality Center if diagnostics has lead to replacement of the transmission torque converter.

PIE0554B

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information from the technicians for the following conditions for the cluster.

110089005O

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

PIT5745

Service Bulletin/Repair Instructions

This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw.

030601023D

Service Bulletin/Repair Instructions

This information bulletin explains how to measure for oil consumption and possible reasons for loss of oil.

060089029T

Service Bulletin/Repair Instructions

This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

140604004G

Service Bulletin/Repair Instructions

This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours.

PIT5746

Service Bulletin/Repair Instructions

This Preliminary information communicates information on how dealers can contact the supplier for Associated Accessories offered through GM.

PIT5681A

Service Bulletin/Repair Instructions

This Preliminary information communicates the location of the GM Accessory Performance Brake System Rotor Specifications

070849020Q

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

PIP5729

Service Bulletin/Repair Instructions

This Preliminary information communicates Some customers may comment that the SES lamp is illuminated or was Illuminated and turned off. During inspection Technician may notice DTC P1682 (Ignition 1 Switch Circuit 2) active or stored in history. DTC?s P0101, P0689. P16A7 or P16BC may also be active or stored in history. Additionally, vehicle may have been into the dealer on a prior service visit and had the MAF sensor replaced for DTC P0101.  This condition may be caused by a faulty ignition relay or underhood fuse block terminal concern.

PIT4506E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks and Utilities may ask if they can lower their tire pressures. Tire pressures being set to the "Tire and Loading Label" will ensure the safe handling and ride characteristics of the truck and should not be lowered.

16NA383

Service Bulletin/Repair Instructions

This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

030089006R

Service Bulletin/Repair Instructions

This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.

060089029S

Service Bulletin/Repair Instructions

This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

PIP5504D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians are referred to Torque Converter Diagnosis in SI.

20NA098

Service Bulletin/Repair Instructions

This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC.

150601002J

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

000310003Z

Service Bulletin/Repair Instructions

This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).

060089029R

Service Bulletin/Repair Instructions

This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

PIT5511D

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure.  This is done to protect the Driver Information Center from damage.

PIT5195F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

PIT5259F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the door striker cover will be shipped with the vehicle from the assembly plant.  Technician is to make sure the rounded side of the cover is positioned towards the outboard side of the vehicle.

PI0281H

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

PIT4322K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

060089029Q

Service Bulletin/Repair Instructions

This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.

100089005I

Service Bulletin/Repair Instructions

This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.

PIT5622B

Service Bulletin/Repair Instructions

This Preliminary information communicates instructions dealer to inspect for a broken or damaged side objector sensor/module bracket if there is a "Side Detection System Unavailable" message displayed at startup.

060089029P

Service Bulletin/Repair Instructions

This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.

PIT5490B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Trailer Brake message in the Driver Information Center. Also the vehicle will have a Diagnostic Trouble Code U0415 set. Technician will fill the master cylinder brake fluid reservoir to the maximum level.

PIT5509F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

PIT5426C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician for a water leak in in the second and third row seating area. Inspect the C-pillar which is the body vertical structure behind the rear passenger door area of the affected side of the vehicle for water intrusion or water marks on the seat belt retractor. If water evidence is found on the seat belt webbing or the retractor the seat belt/ retractor must be replaced after the water leak has been corrected and verified. There are 3 areas of seam sealer that will need to be addressed. After gaining access to the C-pillar and rear quarter panel area inspect for voids or missing seam sealer and apply a clear flow able seam sealer where needed.

070089037O

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance programs.

140604004F

Service Bulletin/Repair Instructions

This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours.

PIT5586D

Service Bulletin/Repair Instructions

This Preliminary information communicates a customer concern of IPC gauges inoperative or fluctuate, No Start, No Crank, SIR Light / Service Airbag Message, Service Suspension Message, Radio display blank, Steering Wheel Controls (SWC) not illuminated, Turn Signal no audible feedback, HVAC controls inoperative. During diagnostics a technician may find any of the following DTC's: B1011, B1370, B3980, U0020, U0029, U007D, U0073, U0078, U0100, U0101, U0102, U0104, U0140, U0151, U0155, U0164, U0184, U0186, U0198, U0422. Dealer is instructed to check Serial Data Gateway Module X2 connector for terminal concerns and repair as needed.

19NA004

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of hearing a squeak or creak from the right rear of vehicle while driving.

PIE0554

Service Bulletin/Repair Instructions

This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the Instrument Panel Cluster (IPC) Gages at Zero, Multiple Warning Lights On, No Chimes and/or Turn Single Audio.

150601002I

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

PIT4261F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

PIT5403F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

020089002S

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

PIE0554A

Service Bulletin/Repair Instructions

This engineering information (EI) is requesting information from the technicians for issues regarding Instrument Panel Cluster (IPC) Gages at Zero, Multiple Warning Lights On, No Chimes and/or Turn Single Audio.

050310020G

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.

060089026P

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated (CCND) Labor Operation Numbers.

20NA050

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to clear the codes and test the Tcase if found that the customer has tried to shift the t-case from 4lo to Hi gears while driving.

990089019S

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.

PIT5287F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.

PIT5390D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have the alarm sounding when learning new key fobs after the original key fobs were lost. Technician will open the driver?s door and allow the Content Theft Deterrent alarm to activate, which will pulse the horns and exterior lamps for approximately 30 seconds and the alarm will shut off at this time. As long as the driver?s door remains open the alarm will not turn back on and the new transmitters can be programmed.

PIT5552D

Service Bulletin/Repair Instructions

This Preliminary information communicates repair information for the rear vision camera or surround vision camera image being: -  Yellow -  Blurry -  Distorted -  Image scrolling -  Image with NO gridlines -  Screen is blue with gridlines -  Screen is blue with Service Rear Vision System message

040601029J

Service Bulletin/Repair Instructions

This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules.

040089015U

Service Bulletin/Repair Instructions

This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).

N192285050

Service Bulletin/Repair Instructions

Customer Satisfaction Program - Certain vehicles that had the front passenger seat cushion frame previously replaced, may not have had the adjuster stops transferred and are missing on the replacement part. The front passenger seat may be in a position beyond the occupant design travel range.Dealers are to inspect the front passenger seat tracks for the presence of both adjuster stops and install missing adjuster stops if necessary.

000310003Y

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

PIT5307G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a service engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.

050307009J

Service Bulletin/Repair Instructions

This informational bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles.

150089005C

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Essential Tools that include Consumable Parts (U.S. Only).

16NA119

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.

18NA239

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to add washers on the lower column mounting bracket locations due to the shaft laying on the metal support at the bottom of the column.

17NA304

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace both fuel feed lines for a leak and/or noise coming from pulses in the fuel line.

DOR-D8C4T-03

Service Bulletin/Repair Instructions

This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.

DOR-E2P5T-03

Service Bulletin/Repair Instructions

This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.

110089002D

Service Bulletin/Repair Instructions

This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.

19NA212

Service Bulletin/Repair Instructions

This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away to correct a crank/No Start condition.

050307009I

Service Bulletin/Repair Instructions

This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.

PIT5665A

Service Bulletin/Repair Instructions

This Preliminary information communicates customers may comment on poor remote keyless entry (RKE) range (less than 20 feet.) Some customers may comment that the RKE fob must be held next to the driver door handle before the doors will unlock when passively attempting to unlock the door.  The Radio Antenna Amplifier may be causing the range issue.

15NA010

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.

20NA016

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.

PIP5504C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians are referred to Torque Converter Diagnosis in SI.

19NA193

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of Phone Charging Cycles On and Off When Connected to the Single Port USB Hub.

PIP5130K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.

PIP5503B

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being overfull on oil causing an engine vibration concern. The technician is advised to inspect for contaminnants and adjust the engine oil level as needed.

PIP5531A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015?0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that "mating" surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped

PIT5282F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness.  Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).

PI0592F

Service Bulletin/Repair Instructions

This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

PIT5479C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

100089009D

Service Bulletin/Repair Instructions

This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.

080089014F

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

PIP5330D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.

19NA137

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to add PET tape to the brake cables if the cause of the customers concern.

010842001M

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.

080310006G

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.

PIT5527C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that show a "Take Steering" message on the Driver Information Center along with a warning chime/alert. Dealer should be advised the purpose of the message is to alert the driver that the Lane Keep Assist system has not detected active steering input from the driver (hands off the steering wheel).

PIT5594B

Service Bulletin/Repair Instructions

This Preliminary information communicates a normal DIC message after learning keys/fobs which indicates the drivers memory position.

990420002K

Service Bulletin/Repair Instructions

This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.

PIT5509E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

PIT5550C

Service Bulletin/Repair Instructions

This Preliminary information communicates that an inoperative third row folding seat back may not fold down or up.  This information advises dealers on how the seat functions and also a common area where an open circuit may be found between the third row seat module and the seat position sensor.  It provides repair instructions if a concern is found with the circuits between the third row folding seat module and the seat back position sensor, as well as advising the dealer to look for bent/damaged seat recline mechanisms.

PIT5717

Service Bulletin/Repair Instructions

This Preliminary information communicates if the sunroof, rear sliding window, and/or wireless charging are found to be inoperative due to the F2DL and/or the F8DL fuse(s) being open.  Inspect the center console harness area at the hinge pivot point for chaffed circuits.

PIT5288H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.

PIT5392D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a detent / click with a feel of increased resistance when the accelerator pedal is about ¾ of the way. The new accelerator pedal design has a built-in detent position near the last 1/4 of pedal travel. Dealer should communicate to the customer this is a normal operating characteristic of the vehicle and no repair attempts should be performed.

PIT5447C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps needed to diagnose and repair vehicles that may have a rattle noise from the dash. Technician will need to inspect for the rear heater pipes contacting the passenger side exhaust manifold.  If the rear heater pipe is found to be contacting the exhaust manifold, reposition the heater pipe so it no longer makes contact.

PIT5535E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.

100089006G

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).

PIT5365D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how the radio display gets the air ambient temperature. On 1500 series trucks and all sport utility vehicle with regular production option code IO3 radio the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio. On 1500 series trucks and all sport utility vehicle with regular production option code IO4, IO5, or IO6 the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface. On 2500/3500 series trucks production option code IO3 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio. On 2500/3500 series trucks production option code IO4, IO5, or IO6 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface.

010601011K

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

100089009C

Service Bulletin/Repair Instructions

This informational bulletin provides information on key code security and information on GM key code look up applications.

PIP5504B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians are referred to Torque Converter Diagnosis in SI.

PIT5551E

Service Bulletin/Repair Instructions

This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting.  This is normal when the FAB has been set to  "Alert".

010089010N

Service Bulletin/Repair Instructions

This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).

PIP5407B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.

PIT5278E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with erratic or hesitation when opening and closing the power liftgate. There may be a diagnostic trouble code B153A set in the power liftgate module. This concern could occur if the left liftgate actuator is internally coming apart. The actuator will need to be replaced however care must be taken when removing the actuator from the vehicle. If the internal portion of the actuator had completely separated the end of the actuator could become a projectile when removed. Obtain a number 8 self-tapping screw that measures 1 ½ inches long.  Fully open the liftgate and install the screw anywhere in a 30 millimeter space from the bottom of the smooth tube to secure the tubes.  Continue with the liftgate actuator by following the liftgate power assist actuator procedure in service information.

PIT5576C

Service Bulletin/Repair Instructions

This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar.   Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.

PIP4670H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.

PIP5606E

Service Bulletin/Repair Instructions

This Preliminary information communicates A vehicle may have a tick noise from the engine cold, initial start in the morning. A lifter may not have sufficient amount of oil during cold start operation (not pumped up).  As information comes in the Pi will be updated and when the final repair is out this this PI will be changed to a Bulletin

17NA073

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding the field action courtesy transportation policy.

N192257100

Service Bulletin/Repair Instructions

N192257100 - EM - General Motors has decided to conduct a voluntary emissions recall involving certain 2019 Chevrolet Silverado, Suburban, Tahoe and GMC Sierra vehicles equipped with a performance air intake system. The required Vehicle Emission Control Information (VECI) label may not have been installed. Since a new label can be easily installed, and to reduce customer inconvenience, the label will be sent directly to customers of record along with the installation instructions. Customers may install the label or, if they desire, they may take the label to their dealer for installation at no charge.

PIP5630C

Service Bulletin/Repair Instructions

This Preliminary information communicates A vehicle may have a concern of no oil pressure and/or P0521 set. the releif valve in the pump is sticking or the number 1 main bearing is damaged. Drop oil pan and confirm #1 main is spun or not.  If bearings are OK Then change oil pump.

PIT5448F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

PIT5481E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Starting with 2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.

PIP5407A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.

PI0592E

Service Bulletin/Repair Instructions

This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961).

090604026R

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

130089008B

Service Bulletin/Repair Instructions

This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC.

000601026M

Service Bulletin/Repair Instructions

This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

070601016F

Service Bulletin/Repair Instructions

This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

19NA183

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Mandatory VECI Label Replacement for (5W7) Performance Air Intake Kits.

PIP5630B

Service Bulletin/Repair Instructions

This Preliminary information communicates A vehicle may have a concern of no oil pressure and/or P0521 set. the releif valve in the pump is sticking or the number 1 main bearing is damaged. Drop oil pan and confirm #1 main is spun or not.  If bearings are OK Then change oil pump.

080730026F

Service Bulletin/Repair Instructions

This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

PIP5573B

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer technician that the torque converters for the 10L80 and 10L90 10 speed transmission are on restriction through the Product Quality Center. Dealers are advised to contact the Product Quality Center if diagnostics has lead to replacement of the transmission torque converter.

PIT5288G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.

PIT5572C

Service Bulletin/Repair Instructions

This Preliminary information communicates a Service Adaptive Cruise With DTC C018C SYM3A After Replacing K14 Distance Sensing Cruise Control Module and provides tips for completing all necessary steps and to contact TCSC if configuration does not complete correctly.

PIC6086F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area.  Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.

PIP5663

Service Bulletin/Repair Instructions

This Preliminary information communicates  AFM / DFM usage  Information. providing additional information on the AFM and DFM systems

PIP5477L

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer technician that the 10L90 and 10L80 transmissions part restriction has ended.

PIT5448E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

990089019R

Service Bulletin/Repair Instructions

This informational bulletin provides process information for the (GWM) and (WPC) parts return program.

PIP5606D

Service Bulletin/Repair Instructions

This Preliminary information communicates A vehicle may have a tick noise from the engine cold, initial start in the morning. A lifter may not have sufficient amount of oil during cold start operation (not pumped up).  As information comes in the Pi will be updated and when the final repair is out this this PI will be changed to a Bulletin

PI1344C

Service Bulletin/Repair Instructions

This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.

PIT5622A

Service Bulletin/Repair Instructions

This Preliminary information communicates instructions dealer to inspect for a broken or damaged side objector sensor/module bracket if there is a "Side Detection System Unavailable" message displayed at startup.

PIP5630A

Service Bulletin/Repair Instructions

This Preliminary information communicates A vehicle may have a concern of no oil pressure and/or P0521 set. the releif valve in the pump is sticking or the number 1 main bearing is damaged. Drop oil pan and confirm #1 main is spun or not.  If bearings are OK Then change oil pump.

PIT5535D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.

050604022Q

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

100845001G

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.

1308116001E

Service Bulletin/Repair Instructions

The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

PIT5317C

Service Bulletin/Repair Instructions

This Preliminary information communication provides information to the technician about vehicles with the rear body fuse block with a loose fuse connection. Technician will need to check terminal tension on the rear fuse block. Technician will need to replace the rear body fuse block if poor terminal tension is the issue. Technician will need to replace the appropriate terminated lead if something other than the main power buss bar has poor terminal tension.

000601012J

Service Bulletin/Repair Instructions

This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

090604026Q

Service Bulletin/Repair Instructions

This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

PIT5530C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory Accessory 22" Wheels Regular Production Option Code (SES, SEU, SEY, OR SEZ)  or production 22" wheels Regular Production Option Code (RPT or SMI) also during any service requiring wheel removal.

PIT3665H

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.

PIT5586C

Service Bulletin/Repair Instructions

This Preliminary information communicates a customer concern of IPC gauges inoperative or fluctuate, No Start, No Crank, SIR Light / Service Airbag Message, Service Suspension Message, Radio display blank, Steering Wheel Controls (SWC) not illuminated, Turn Signal no audible feedback, HVAC controls inoperative. During diagnostics a technician may find any of the following DTC's: B1011, B1370, B3980, U0020, U0029, U007D, U0073, U0078, U0100, U0101, U0102, U0104, U0140, U0151, U0155, U0164, U0184, U0186, U0198, U0422. Dealer is instructed to check Serial Data Gateway Module X2 connector for terminal concerns and repair as needed.

PIT5692

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about how to diagnosis a battery draw that may be caused by a module back feeding voltage in the ignition relay circuits making the vehicle think it is still awake.

19NA139

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to pry the upper and lower quarter rear trim panel sheet metal apart to eliminate a creak noise heard from the quarter lower rear trim panel area.

PIP5335C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.

PIP5573A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer technician that the torque converters for the 10L80 and 10L90 10 speed transmission are on restriction through the Product Quality Center. Dealers are advised to contact the Product Quality Center if diagnostics has lead to replacement of the transmission torque converter.

PIP5477K

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer technician that the 10L90 and 10L80 transmissions have been place on a part restriction. Dealers are to contact the Product Quality Center before replacing the transmission assembly.

PIP5286B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician for a vehicle setting both a P2635 and P018B diagnostic trouble codes. The following steps may help to determine if this is caused by a fuel pressure sensor not reading the low end of the pressure range.  Technician is to make sure the engine is cold and install the Multiple Diagnostic Interface along with Global Diagnostic System 2.  Navigate to fuel system depressurize and at engine idle depressurize the fuel system. The fuel pressure sensor value should drop to 0 and the engine will stall.  If a sensor is causing this concern the suspected sensor will not drop to 0 the engine will stall however the sensor will still read 30 to 40 pounds per square inch.

PIT5457D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the driver and passenger sill plate to gain access to the wire harness. If any open, damaged, or corroded wires should be repaired.

PIP4670G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.

PIP5654

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer technician that the valve body Part Unique Number (PUN) may contain the letter O or the number 0.

060847001O

Service Bulletin/Repair Instructions

This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.

PIT5572B

Service Bulletin/Repair Instructions

This Preliminary information communicates a Service Adaptive Cruise With DTC C018C SYM3A After Replacing K14 Distance Sensing Cruise Control Module and provides tips for completing all necessary steps and to contact TCSC if configuration does not complete correctly.

PIT5202E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission, now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.

PIP5298B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician for a Service Engine Soon light with a Diagnostic Trouble code P0300 set. There may be a rough running engine associated with this concern. If service information diagnostics have been completed and there is still no trouble found, the technician is to inspect for a possible terminal tension concern on the ignition coil power feed for the cause of the rough running engine and or the P0300.  For the Service Engine Soon light or traction control lamp concern check the X2 connector of the under hood fuse block for poor pin retention.

080730035D

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

PIT5049E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.

PIT5551D

Service Bulletin/Repair Instructions

This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting.  This is normal when the FAB has been set to  "Alert".

PIT3219F

Service Bulletin/Repair Instructions

This Preliminary Information communicates to technicians that the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49).   These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.

PIT3665G

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.

PIT5683

Service Bulletin/Repair Instructions

This Preliminary information communicates that unwanted liftgate opening can occur if the customer leaves a programmed fob in the vicinity of the passive liftgate antenna.  If the antenna can locate a programmed fob in said area, the gate will open if the liftgate open switch or hands free sensor is activated.

000310006N

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).

19NA097

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of Water Collecting Inside of Muffler Causing a Hard or No Start.

PIT5681

Service Bulletin/Repair Instructions

This Preliminary information communicates the location of the GM Accessory Performance Brake System Rotor Specifications

PIP5498L

Service Bulletin/Repair Instructions

This Preliminary information communicates A vehicle may have a concern of DTC P050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.

PIT5291E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have wind whistle noise heard from the right or left rear quarter glass area when driving at highway speeds or with a cross wind. Technician will inspect the quarter glass for excessive urethane. If excessive urethane is found use a sharp knife and cut off the excessive urethane. Also the technician will install foam tape along the entire length of the tail light assembly.

080089014E

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

PIE0506B

Service Bulletin/Repair Instructions

This engineering information PI ends the need for information from the field if a customer has received error message 220_7 when trying to remote start their vehicle with mobile app.

140604004E

Service Bulletin/Repair Instructions

This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours.

17NA153

Service Bulletin/Repair Instructions

This informational bulletin provides information and operating tips for the hands free lift gate.

PIP5569A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.

PIT5404E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming.  Replace or repair any of the issue that was found in the inspection. If the vehicle is equipped with a 4.3 liter or 5.3 liter engine an updated exhaust system is now available.

PIT5377G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the step needed to diagnose and repair vehicles that may have uneven brake pad wear. Technician will need to inspect and measure the brake pads thickness. Also determine the customer?s driving style. The disc brake pads should only be replaced if the friction surface is worn to within 2.0 mm (0.079 in) of the mounting plates. The rotors and pads should be replaced with the updated part number If the pads are out of specification, perform normal Service Information diagnostics to determine the cause of the concern.

18NA377

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of front seat lateral movement and/or click type noise while driving.

PIT5311E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle?s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector with part number 23404450.

PIT5195E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

PIT5564B

Service Bulletin/Repair Instructions

This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set.

PIT5308D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with the ignition off, Crank no start, Start and Stall, and vehicles equipped with the diesel engine, the blower motor may stay on after the engine is turned off. Technician may find Diagnostic Trouble Code P2537 and/or P129D set. Technician will need to Use a voltmeter and check circuit 5985 at the Engine Control Module and Transmission Control Module. If no or low voltage is found, use the wiring diagram in Service Information and perform normal circuit diagnosis.

PIP5423B (1)

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.

PIP5369C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have "Service 4 Wheel Drive" message on the Driver Information Center. Provides the technician with additional information to ensure that the TCCM contains the latest software released to address previous issues, also advises of default action changes. Calls out specific circuits to be inspected to help isolate intermittent codes.

PIP5423B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.

19NA071

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of forward collision/active safety system inoperative, no messages or alerts. Technician may find DTC?s B390A?45, B390A?58 and/or DTC?B390A?67 are set.

19NA072

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Rear Compartment Floor Stowage Compartment Cover Handle Availability as Service Part.

PIP5423A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.

17NA267

Service Bulletin/Repair Instructions

This informational bulletin provides information for 22" accessory wheel/tire usages.

030729004L

Service Bulletin/Repair Instructions

This informational bulletin provides normal operating characteristics and diagnostic information on Manual transmissions.

PIP4670F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.

030603004Y

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

1008110001H

Service Bulletin/Repair Instructions

This informational bulletin provides information on proper use of floor mats.

19NA063

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to adjust the shifter cable if found the cause of the customers concern.

110089005N

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.

030089006Q

Service Bulletin/Repair Instructions

This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.

060089029O

Service Bulletin/Repair Instructions

This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.

040089053G

Service Bulletin/Repair Instructions

This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.

070849020P

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

1008110001G

Service Bulletin/Repair Instructions

This informational bulletin provides information on proper use of floor mats.

PIT3098G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a lean to the left or right. Technician will need to measure fender wheel-opening heights, front and rear, to quantify vehicle lean. Fender wheel-opening heights are related to, but distinct from, trim height. The front wheel-opening height is known as P height, and the rear wheel-opening height is known as R height. Adjust and heights that are out of specification. After all adjustments are done, perform a front-end alignment and check headlight aim.

PIT5379E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a content theft alarm sounding for no apparent reason. Technician may use all published Service Information diagnostics and has not found the cause of the unwanted content theft alarm sounding. Technician should use Global Diagnostic System 2 to review the Body Control Module parameters for "Content Theft Deterrent Trigger History". If the trigger is an Intrusion inspect for items hanging from the rear view mirror, solar powered dancing characters. When the trigger is a Glass breakage inspect the two rear quarter-panel windows and also in the liftgate glass. The quarter panel windows are attached to the body harness with a connector that looks similar to a 9 volt battery connector inspect them to be fully seated in on the glass. When the trigger is Ignition Voltage/Battery reconnect detected during a cold ambient temperature remote vehicle start event technician should call GM General Motors Technical Assistance Center.

100845001F

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".

090089002Q

Service Bulletin/Repair Instructions

This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.

PIT5665

Service Bulletin/Repair Instructions

This Preliminary information communicates customers may comment on poor remote keyless entry (RKE) range (less than 20 feet.) Some customers may comment that the RKE fob must be held next to the driver door handle before the doors will unlock when passively attempting to unlock the door.  The Radio Antenna Amplifier may be causing the range issue.

110849001Z

Service Bulletin/Repair Instructions

This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.

PIE0506A

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information that the dealer needs to call the engineer listed if a customer has received error message 220_7 when trying to remote start their vehicle with mobile app.

050604022P

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

PIP5630

Service Bulletin/Repair Instructions

This Preliminary information communicates A vehicle may have a concern of no oil pressure and/or P0521 set. the releif valve in the pump is sticking or the number 1 main bearing is damaged. Drop oil pan and confirm #1 main is spun or not.  If bearings are OK Then change oil pump.

060605001H

Service Bulletin/Repair Instructions

This informational bulletin explains the normal characteristics of exhaust noise during active fuel management when in Three or Four Cylinder Mode.

150601002H

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.

PIT5426B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician for a water leak in in the second and third row seating area. Inspect the C-pillar which is the body vertical structure behind the rear passenger door area of the affected side of the vehicle for water intrusion or water marks on the seat belt retractor. If water evidence is found on the seat belt webbing or the retractor the seat belt/ retractor must be replaced after the water leak has been corrected and verified. There are 3 areas of seam sealer that will need to be addressed. After gaining access to the C-pillar and rear quarter panel area inspect for voids or missing seam sealer and apply a clear flow able seam sealer where needed.

120089002C

Service Bulletin/Repair Instructions

This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.

PIT5390C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have the alarm sounding when learning new key fobs after the original key fobs were lost. Technician will open the driver's door and allow the Content Theft Deterrent alarm to activate, which will pulse the horns and exterior lamps for approximately 30 seconds and the alarm will shut off at this time. As long as the driver's door remains open the alarm will not turn back on and the new transmitters can be programmed.

PIT5552C

Service Bulletin/Repair Instructions

This Preliminary information communicates repair information for the rear vision camera or surround vision camera image being: -  Yellow -  Blurry -  Distorted -  Image scrolling -  Image with NO gridlines -  Screen is blue with gridlines -  Screen is blue with Service Rear Vision System message

PIP4021D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that a whine noise heard from the automatic transmission fluid pan hear with the the key on and engine off, or for up to one minute after the vehicle has been shut off should be deemed a normal characteristic.

PIT5282E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness.  Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).

PIT5527B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that show a "Take Steering" message on the Driver Information Center along with a warning chime/alert. Dealer should be advised the purpose of the message is to alert the driver that the Lane Keep Assist system has not detected active steering input from the driver (hands off the steering wheel).

010310003R

Service Bulletin/Repair Instructions

This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.

PIT5287E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.

PI0564K

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

090089016F

Service Bulletin/Repair Instructions

This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.

110849001Y

Service Bulletin/Repair Instructions

This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off.

PIT5391E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.

PIP5554A

Service Bulletin/Repair Instructions

This Preliminary information communicates P0016 setting after internal engire repair. The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.

090089002P

Service Bulletin/Repair Instructions

This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.

PIT5307F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a service engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.

010089010M

Service Bulletin/Repair Instructions

This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).

080089014D

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

030603004X

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

17NA170

Service Bulletin/Repair Instructions

This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.

16NA339

Service Bulletin/Repair Instructions

This informational bulletin aids the technician on diagnosing possible vibrations in a vehicle, methods used for testing each scenario and documenting findings.

100089005H

Service Bulletin/Repair Instructions

This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.

040089015T

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on required operating procedures.

N182190820

Service Bulletin/Repair Instructions

N182190820 - Customer Satisfaction Program. Certain vehicles, may have a condition where the power steering belt may slip due to tooth wear-out or poor belt tooth-to-gear tooth fit. Power steering assist may be reduced or lost intermittently, if early warning signs are ignored. Early warnings may include a ?Steering Assist is Reduced? message, audible clicking / squealing sounds, or a change in steering effort. Dealers will replace the steering gear assembly.

PIT5565B

Service Bulletin/Repair Instructions

This Preliminary information communicates a repair procedure for a squeak/squawk type noise coming from the lower column/drivers footwell area when turning.  It explains how to properly lubricate the column shaft boot where the shaft interacts with the boot where it passes through the boot.

060089026O

Service Bulletin/Repair Instructions

This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).

18NA369

Service Bulletin/Repair Instructions

This informational bulletin provides information for replacing the power liftgate assist actuator.

PIC5650F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

17NA066

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow test.

010842001L

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.

080089014C

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

PIP5212B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise. Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.

PIT5479B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

PIP5503A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being overfull on oil causing an engine vibration concern. The technician is advised to inspect for contaminnants and adjust the engine oil level as needed.

PIE0498

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information on product issue with the door weather strip, door body fit, and/or rear tail lamp moisture.

N182188440

Service Bulletin/Repair Instructions

Customer Satisfaction Program. Certain vehicles may have an incomplete or missing braze between the harness bulkhead support bracket and the fuel rail assembly. If the braze is incomplete the support bracket may detach from the fuel rail assembly over time. Wiring may sever and compromise the function of the fuel pump and/or the 4 passenger side injectors. If the function of the fuel pump and/or injectors is compromised, the Check Engine Light will come on, and you could experience reduced engine power. Loss of propulsion is possible, and there is a remote chance of fire if there is a fuel leak. Replace fuel rail assembly.

000310003X

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

060847001N

Service Bulletin/Repair Instructions

This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.

060850009J

Service Bulletin/Repair Instructions

This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.

18NA360

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the side mirror cameras if found the cause of the reduced key fob range.

18367

Service Bulletin/Repair Instructions

Customer Satisfaction. Certain vehicles, equipped with the 10-speed automatic transmission (RPO MF6), may have a condition in which the transmission manual shaft pin was not seated properly. If the shaft pin were to migrate out of position, the driver may find they cannot shift the vehicle into any gear other than the last one selected. The customer may be unable to return the vehicle back to park, in which case they would be required to engage the parking brake to ensure the vehicle does not roll from its intended position. Dealers will replace the transmission manual shaft pin. Private Message sent to select dealers.

PIT5350B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that there have been some reports that the current engine hours are not correct and display 0.0. Technician will need to program the Instrument Panel Cluster using Service Programming System.

PIP5570A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer a condition where a tick noise may be present inside a vehicle while driving. This may be the result of a deformed or improperly seated steering shaft seal allowing engine compartment sounds into the vehicle. Dealers are instructed to replace or reinstall the boot as needed and are informed the condition is being reviewed by engineering.

PIT5284D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have a rattle noise from the second row seat. Technician will need to inspect the striker not aligned properly in latch opening. To repair this condition, rework/adjust the striker in the direction to center it in the latch opening. An adjustable wide mouth metal working tool may be used to adjust the striker just enough to center in the latch opening. Technician may find a seat bottom latch may have an unequal latch opening side-to-side for the striker to seat into. To repair this condition, with the affected seat in the tumbled forward position, while applying steady, firm pressure, cycle the seat down into the latched position. Some vehicles built prior to 09/21/2015 with 60/40 Split Bench Seat may have 60-percent long side bench, inboard latch may not be properly aligned in striker opening. Technician will need to place a 2.6 mm thick flat washer over the 40 percent seat base stud, not the floor stud. Some vehicles may have a seat base plat that rattles against the rib in the floor pan. Apply Mylar tape to the floor pan under the seat plate to provide relief for the rattle condition.

PIP5477J

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer technician that the 10L90 and 10L80 transmissions have been place on a part restriction. Dealers are to contact the Product Quality Center before replacing the transmission assembly.

PIT5445C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician of additional information when diagnosing a service driver assist message with a diagnostic trouble code B172E and or a B172F. The haptic seat motor has a pigtail lead coming off of it. In many cases the wiring pigtail near the haptic seat motor has broken and will require replacement.

PIP5606B

Service Bulletin/Repair Instructions

This Preliminary information communicates A vehicle may have a tick noise from the engine cold, initial start in the morning. A lifter may not have sufficient amount of oil during cold start operation (not pumped up).  As information comes in the Pi will be updated and when the final repair is out this this PI will be changed to a Bulletin

PIT3946C

Service Bulletin/Repair Instructions

This Preliminary Information communicates an issues with the headliner sagging and how to reattach the velcro using Hardman Double Bubble Epoxy part number 04001.

PIT5594A

Service Bulletin/Repair Instructions

This Preliminary information communicates a normal DIC message after learning keys/fobs which indicates the drivers memory position.

PIT5272B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a whistle noise in the vehicle from the driver or passenger side. Technician will need to inspect for voids in the body sealer on the left or right side A-pillar. Technician should also inspect for voids in the body sealer at the cowl seam and apply sealer as necessary.

PIE0475A

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information pictures of windshield, steering wheel and/or door trim panel for product issues covered under warranty.

PIC6086E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area.  Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.

PIP5159C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on and Diagnostic Trouble Code P0300 - P0308  may set. Technician will inspect for lose sparkplug wire. If a spark plug wire is found lose check for a missing ?C? clip on the wire end for the ignition coil. If the clip is missing replace the wire.

PIT5438E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.

PIT5550B

Service Bulletin/Repair Instructions

This Preliminary information communicates that an inoperative third row folding seat back may not fold down or up.  This information advises dealers on how the seat functions and also a common area where an open circuit may be found between the third row seat module and the seat position sensor.  It provides repair instructions if a concern is found with the circuits between the third row folding seat module and the seat back position sensor, as well as advising the dealer to look for bent/damaged seat recline mechanisms.

PIP5491A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician when diagnosing intermittent circuit concerns to look at the connector for missing weather pack seals that could allow water intrusion into the connector and lead to corrosion on the terminals.

18306

Service Bulletin/Repair Instructions

18306 - Customer Satisfaction Program. Certain 2019 model year Chevrolet Suburban and Tahoe vehicles were built with cloth seats instead of vinyl seats. Dealers will replace the entire front row seat unit.

PIT4322J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

PIT5403E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

PIT5576B

Service Bulletin/Repair Instructions

This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.

PIT5361D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have issues were the customer will need increased effort to depress the brake pedal. Technician may find fluid in the brake booster and/or the booster vacuum line. Technician will need to replace Vacuum Pump, Brake Booster, Master Cylinder, Vacuum Pump Belt and the Vacuum Line between the booster and the pump.

PIT5241F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about customers that may request the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup or SUV when the vehicle was not ordered with the option. Dealer should advise the customer it cannot be added to the vehicle.

PIT5448D

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

PIT5586B

Service Bulletin/Repair Instructions

This Preliminary information communicates a customer concern ofIPC gauges inoperative or fluctuate, No Start,No Crank,SIR Light / Service Airbag Message, Service Suspension Message,Radio display blank, Steering Wheel Controls (SWC) not illuminated, Turn Signal no audible feedback,HVAC controls inoperative. During diagnostics a technician may find any of the following DTC's: B1011, B1370, B3980, U0020, U0029, U007D, U0073, U0078, U0100, U0101, U0102, U0104, U0140, U0151, U0155, U0164,U0184, U0186, U0198, U0422. Dealer is instructed to check Serial Data Gateway Module X2 connector for terminal concerns and repair as needed.

PIT5481D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist.Starting with2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.