108463
Service Bulletin/Repair Instructions
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
108463
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
108464
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
Y22 Combo Rev1
Customer Satisfaction Notification Y22 Driver Airbag Emblem
Y22 Combo
Customer Satisfaction Notification Y22 Driver Airbag Emblem
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
72301
SAFETY RECAL W09 DRIVER AIR BAG EMBLEM Updated Dealer Instructions
S1121000006 Rev.
(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
S1121000006RevA
(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
TS-WI-0290
Service Bulletin sent to all dealers to inspect L-track bolts for correct torque and to incorporate torque check as part of regular maintenance
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
23027
Return: Wiring Assy - Engine You have been identified as either having stock, or have stock in transit to your dealership. Please return stock packaged before 2016/07/31 (31 July, 2016)of follow ing part numbers:68176457AF, 68176459AF. Please return suspect parts back to your facing depot using Return Code 02, before 13 September, 2016.
23104
05182535AD - Lamp Assy ?Tail Light LT You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05182535AD . See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
23137
Inspect and Return: Trim Cover Assy - A-Pillar Rt/Lt You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part numbers: 1ZA04DX9AE, 1ZA05DX9AE. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
20244
CBXDP361AA Return: Spacer Kit - Visor You have been identified as either having stock, or have stock in transit to your dealership. Please return stock of part number CBXDP361AA. Replacement part number is CBXDP361AB w hich is in stock and available for order. Please return suspect parts back to your facing depot using Return Code 02, before 16 September, 2016.
Volume 2, Issue
Warranty Operations Newsletter Updates from Warranty Operations
22867
Inspect and Return: Solenoid Module - Transmission You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of follow ing part numbers:52120000AA, 52119435AF, 05078709AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
22892
Return: Lamp Assy - CHMSL& Cargo Light You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of follow ing part numbers:55372082AE, 55372082AD, 55372082AC, 55372082AB, 55372082AA. Replacement part number is 55372082AF w hich is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
22958
1NT30XDVAC - Inspect and Return: Panel - Instrument Panel You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 1N T30XDVAC. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
20616
P/N CBSZR068AA: Inspect & Return: Module Kit - Occupant Restraint You have been identified as either having stock, or have stock in transit to your dealership. Please return part number CBSZR068AA as per the QIR attached. Replacement part can be obtained by ordering the same part number (CBSZR068AA) Please return suspect parts back to your facing depot using Return Code 02, before 02 September, 2016.
R4880213A$
SHAFT - AXLE HALF NOTE: THE JOINT BETWEEN THE SPLINES ON THE HALFSHAFT AND THE HUB AND BEARING IS AN INTERFERENCE FIT. THE HALFSHAFT NUT IS TO BE USED TO DRAW THE HUB AND BEARING ONTO THE HALFSHAFT SPLINES. THIS IS PARTICULARLY TRUE IF HUB AND BEARING IS ALSO BEING REPLACED
08-052-16
Flash: UConnect and Voice Recognition Inoperative This bulletin involves replacing the Hands Free Module (HFM). The customer may describe the following conditions: · A complete loss of UConnect operation. · A complete loss of Voice Recognition functionality
05170303A
Housing cover mounting bolt holes use self-tapping fasteners. New fasteners are required with housing replacement.
R2118796A
Valve Body. These may cause over drive cycling.
68018095A
HVAC Distribution Housing
RL108213A$
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
R2108213A$
W5A580 (NAG1) Valve Body - complete
9003215
Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
9002887
Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
08-001-15
L25 Interim Repair Procedure Brazil ONLY Upon starting the vehicle the Frequency Operated Button Ignition Key (FOBIK), may not fully seat in the ?ON? position. If not fully seated, under certain operating conditions (for example bumpy roads) the FOBIK could inadvertently move to the ?Accessory? mode. This could cause unintended engine shut off and the passive restraint systems, including the airbags to shut off. This could increase the risk of a crash under certain driving conditions and increase the risk of occupant injury during a crash. Chrysler intends to repair the vehicle free of charge (parts and labor). However, the part required to provide a permanent remedy for this condition is currently not available. NOTE: Chrysler is making every effort to provide the part as quickly as possible.
L25070114
Expansion of previous safety recall L25.
23-014-14
Sliding Door Trim Contacting Vehicle Rear Quarter This bulletin depending on production date, involves either installing or engaging an additional door panel retention point to prevent the door panel from bowing and contacting the body when the sliding door is opened. The customer may experience a door trim panel contacting the quarter panel on either side when opening either of the sliding doors.
08-042-14
Flash: Dead Battery This Bulletin involves updating the Fold and Stow Module (FSM) with new software because the FSM stays awake resulting in a continuous electrical draw. The customer may experience a dead battery.
9002158
Part Description: Wireless Ignition Node Receiver. Issue Description: Wireless Ignition Node Receiver part number 05026875AE is no longer available. The following kits are available as replacements.~ 68241059AA kit for Journey (JC) and Dodge (RT) 3 button FOB.~ 68241066AA kit for Chrysler (RT) 6 button FOB.~ 68241069AA kit for Dodge (RT) 6 button FOB.~ 68241070AA kit for Chrysler (RT) 3 button FOB.~ 68241076AA kit for Dodge (RT) 5 button FOB.
9001329
Part Description: Seat Belt - Retaining Button Kits. Issue Description: Do not replace the entire seat belt if the seat belt web stop button is missing or damaged.~Belt Web Button:~ 1D1 - Light Graystone - 05093280AB Belt Web Button~1D5 - Medium Slate Gray - 05093280AB Belt Web Button~1DA - Pastel Slate Gray - 05093280AB Belt Web Button~1J3 - Medium Khaki - 05093283AB Belt Web Button~ZJ3 - Medium Khaki - 05093283AB Belt Web Button~1L2 - Light Natural Beige - 05114207AA Belt Web Button~BD1 - Light Graystone - 05093280AB Belt Web Button~ BD5 - Medium Slate Grey - 05093280AB Belt Web Button~ BDA - Pastel Slate Gray - 05093280AB Belt Web Button~ ZP7 - Deep Seamist Green - 05093280AB Belt Web Button~ 5JB571D1A$, 5JB571D5A$, 5JB571J3A$, 5JX141D1A$, 5JX141D5A$, 5JX141DVA$, 5JX141J3A$, 5JX14ZJ3A$, 1EY841D1A$, 1EY841D5A$, 1EY841J3A$, 1EY851D1A$, EY851D5A$, 1EY851J3A$ use the following mini Belt Web Buttons:~1D1 - Light Graystone - 05093285AB Mini Belt Web Button~1D5 - Medium Slate Gray - 05093285AB Mini Belt Web Button~1DV - Slate Gray - 05093285AB Mini Belt Web Button~1J3 - Medium Khaki - 05093286AB Mini Belt Web Button~ZJ3 - Medium Khaki - 05093286AB Mini Belt Web Button~ Position the button as originally installed, or use the opposite side as reference.~ Web Button Location CS:~Front Driver O/B: 690 +/- 10 mm~Front Passenger O/B: 435 +/- 10 mm~Rear O/B: 435 +/- 10 mm~Rear Center: 290 +/- 10 mm~Rear Center Mini: 854 +/- 10 mm~ Web Button Location RG/RS SWB:~Front O/B: 550 +/- 6 mm~2nd Row O/B: 558 +/- 6 mm~ 3rd Row O/B: 584 +/- 6 mm~Web Button Location RG/RS LWB:~Front O/B: 550 +/- 6 mm~ 2nd Row O/B: 518 +/- 6 mm (Exception 52029368A$, 04680197A$: 690 +/- 6 mm)~ 3rd Row O/B: 585 +/- 6 mm (Exception 1CK35BD1A$, 1CK35BD5A$, 1CK35ZJ3A$, 52029369A$, 52029370A$: 434 +/-6 mm)~ Apply a small dot of Bond-All Gel, p/n 04467709, around the backside hole of the female button. Press the female button over the post of the male that is sticking through the rearwar
9001645
Part Description: Short Runner Valve (Actuator) Issue Description: Issue 1~ JC,JS '08-09MY 3.5L only~ Caution - Do not replace the intake manifold for a short runner valve (SRV) fault (P1004 / P2008 / P2016 / P2017) or for a manifold tuning valve (MTV) fault (P1005 / P2077 / P2078). Instead follow the service procedure to investigate P codes associated with diagnosis of the SRV or MTV, then cycle the actuator using a diagnostic tool and verify that the PWM output is 50 (+ 2%) de-energized and 80 (+ 2 %) energized. If no problems observed, then idle the vehicle and verify the correct PWM output (50 + 2% PWM). Replace the actuator if you do not get the desired output. Issue 2~ If the SRV actuator or intake manifold is being replaced for a P1004 Short Runner Valve Performance fault code and the vehicle was built prior to 2/5/07 , technicians must complete the module reflash and verification test per TSB 18-003-07 REV. A to ensure the parts need to be replaced. Please reference TSB 18-003-07 REV. A for specific details on the procedure.
9002385
Part Description: Upper and Lower Sliding Door Rollers Issue Description: If you are replacing this part for a NOISE condition, please perform the following procedure:~ 1. Cycle the sliding door to open, then close and inspect the upper track for hinge trim line contact to stud head contact.~ 2. Adjust the upper hinge accordingly to provide adequate clearance from the trim line to the stud heads in the track. See the Service Manual for hinge torque specification.~ 3. Apply a pea size amount of Krytox Lube (Service Part Number 05019060AA) to the upper and lower track at locations.
08-031-13
Flash: Audio Distortion From The Front Door Speakers When The Rear Aux Port Is Used This bulletin involves re-flashing the Amplifier with updated software. The customer may experience audio distortion from the front door speakers when the rear AUX port is in use. The distortion may occurs when playing certain media with a lot of high frequency content. The equalization doesn't have a settings for rear AUX mode and defaulted to the AM mode. The AM mode equalization has a boost for high frequencies. This increase boost can cause the Amp to distort the sound.
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
09-001-13
Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
23-012-12REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
D-11-44
THIS TSB CONTAINS OWNER LETTER. SEE DOCUMENT SEARCH BUTTON BELOW: 2008-2010 MY MINIVANS EXTENDED WARRANTY BULLETIN INFORMATION REGARDING FRONT WHEEL BEARINGS. *LJ
SB-02-003-11
CHRYSLER/DODGE: THE FRONT WHEEL BEARINGS IS HUMMING OR GROWLING. REMOVE AND REPLACE BOTH FRONT WHEEL BEARINGS, IF NECESSARY. *PE
CSN-K19
CHRYSLER GROUP SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE FRONT BEARINGS MAY HAVE A GRINDING NOISE. THERE IS A CAMPAIGN TO FIX THIS. *RM
CS-J-29
CHRYSLER/DODGE: RADIATOR CAP ON ABOUT 276,000 GRAND CARAVAN AND TOWN AND COUNTRY VEHICLES MAY EXPERIENCE ENGINE COOLANT WEEP AND/OR A SLOW LEAK RESULTING IN LOW ENGINE COOLANT LEVELS. THE RADIATOR CAP MUST BE REPLACED. CSC LETTER WAS REC'D. *PE
CS-K-04
DODGE/CHRYSLER: THE AIR CONDITIONING (A/C) DISCHARGE HOSE ON ABOUT 182,000 CERTAIN VEHICLES MAY CRACK AND LEAK REFRIGERANT. THIS COULD CAUSE A LOSS OF A/C COOLING. THE AIR CONDITIONING DISCHARGE HOSE MUST BE REPLACED. CSC LETTER WAS RECEIVED. *PE
SB-J19
CHRYSLER/JEEP/DODGE: CALIFORNIA EMISSIONS WARRANTY ADDENDUM. THE WARRANTY BOOK ON CERTAIN VEHICLES MAY CONTAIN ERRORS OR MAY BE MISSING INFORMATION REGARDING THE COPONENTS COVERED BY THE CALIFORNIA EMISSIONS WARRANTY. DODGE-CARAVAN/GRAND CARAVAN, CHARGE/CHARGER SRT8, MAGNUM/MAGNUM SRT8, VIPER, AVENGER, NITRO, CHALLENGER/CHALLENGER SRT8, DURANGO/DURANGO HYBRID, JOURNEY, RAM 2500/3500, CALIBER/CALIBER SRT4; JEEP COMMANDER, GRAND CHEROKEE/GRAND CHEROKEESRT8, COMPASS, PATROIT, LIBERTY; CHRYSLER TOWN&COUNTRY, PACIFICA, 300 SRT8, PTCRUISER, SEBRING/SEBRING CONV., ASPEN/ASPEN HYBRID.
SB-1800309 REVC
CHRYSLER/JEEP/DODGE: FLASH-DRIVEABILITY IMPROVEMENTS OR MIL ILLUMINATION DIAGNOSTIC TROUBLE CODE P0452-EVAP PRESSURE SWITCH STUCK CLOSED. INCLUDES MY09 TOWN&COUNTRY; VOYAGER AND CARAVAN. *PE
SB-23-13-09
CHRYSLER/DODGE: SLIDING DOOR HANDLE INOPERATIVE IN SUB FREEZING TEMPERATURES. SOME VEHICLES MAY EXPERIENCE AN INOPERATIVE DOOR HANDLE ON EITHER SLIDING DOOR IN COLD SUB FREEZING WEATHER. THE DOOR WILL STILL OPERATE NORMALLY FROM INSIDE THE VEHICLE OR WHILE USING THE POWER ASSIST OPEN FEATURE. *PE
SB-19-001-10
CHRYSLER: POWER STEERING RETURN LINES. INVOLVES INSPECTING AND IF NECESSARY REMOVING AND REPLACING THE GEAR TO COOLER POWER STEERING RETURN HOSE WITH A KEVLAR BRAIDED RETURN HOSE. MAY EXPERIENCE LEAKS IN POWER STEERING RETURN LINE, AT COLD START UP IN TEMPERATURES BELOW-40%C (-40%F) AND INCREASED STEERING EFFORTS OR NOISY POWER STEERING PUMP. *PE
SB-08-001-09
CHRYSLER: AN INTERMITTENT OR PARTIAL UNLATCH OF THE 60 PERCENT THIRD ROW SEAT INBOARD LATCH WHILE ATTEMPTING TO STOW THE SEAT. *PE
H-16
CHRYSLER/DODGE SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE LOW PRESSURE POWER STEERING HOSE ON CERTAIN VEHICLES MAY LEAK UNDER CERTAIN EXTREME COLD CLIMATE OPERATING CONDITIONS. THIS RESULT IN A LOSS OF POWER STEERING ASSIST UPON VEHICLE START UP. CSC LETTER WAS RECEIVED. *PE
TSB-08-037-08
CHRYSLER: AN INTERMITTENT OR PARTIAL UNLATCH OF THE 60 PERCENT THIRD ROW SEAT INBOARD LATCH WHILE ATTEMPTING TO STOW SEAT. *PE
H-30
CHRYSLER DODGE JEEP SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE REMOTE KEYLESS ENTRY TRANSMITTERS ON CERTAIN VEHICLES MAY EXHIBIT POOR RETENTION TO THE VALET KEY AND COULD INADVERTENTLY SEPARATE FROM EACH OTHER. CSC LETTER WAS RECEIVED. *PE
23-022-08
CHRYSLER: FRONT DOOR RATTLE OR DOOR GLASS MAY NOT FULLY ROLL DOWN. *PE
18-025-08
FLASH: MIL ILLUMINATION WITH DTC P1607 - PCM INTERNAL SHUTDOWN TIMER RATIONALITY. THIS BULLETIN INVOLVES SELECTIVELY ERASING AND REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM) WITH NEW SOFTWARE. *PE
21-016-08
FLASH: 4 SPEED AUTOMATIC TRANSMISSION SHIFT IMPROVEMENTS. *NJ
21-017-08
FLASH: 6 SPEED AUTOMATIC TRANSMISSION SHIFT IMPROVEMENTS. *NJ
H 11
CHRYSLER DODGE JEEP SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. CUSTOMER SATISFACTION NOTIFICATION H11; RADIO SOFTWARE UPDATE. THIS NOTIFICATION APPLIES ONLY TO VEHICLES EQUIPPED WITH A MYGIG RADIO (SALES CODE RER WITH NAVIGATION SYSTEM OR REN WITHOUT NAVIGATION SYSTEM). CSC WAS RECEIVED. *PE
08-039
DVD SOFTWARE UPDATE REN MYGIG RADIO FOR MANY RADIO FUNCTIONAL ISSUES AND IMPROVEMENTS. *NJ
08-038
2008 (RT) - FLASH: POWER SLIDING DOOR MODULE - OVERLY SENSITIVE OBSTRUCTION DETECTION. *NJ
08-031
DVD SOFTWARE UPDATE MYGIG RADIO FOR MANY RADIO FUNCTIONAL ISSUES AND IMPROVEMENTS. *NJ
H 06
CHRYSLER DODGE JEEP SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. EMISSIONS RECALL H06-SPARK PLUGS. APPROXIMATELY 440 ENGINES IN THE ABOVE VEHICLES MAY HAVE HAD INCORRECT SPARK PLUGS INADVERTENTLY INSTALLED IN THREE OF THE SIX CYLINDERS. CSC WAS RECEIVED. *PE
08-028-07
FLASH: POWER SLIDING DOOR MODULE - OVERLY SENSITIVE OBSTRUCTION DETECTION. *NJ UPDATED 5/13/08. *NJ
1400108
SLOW FUEL TANK FILL OR PREMATURE FILLER NOZZLE SHUT OFF. *NJ
0802607
THIRD ROW POWER SEAT INOPERABLE - SEAT UPRIGHT WITH SEAT BACK FOLDED TO SEAT. *NJ UPDATED 01/18/08. *NJ
1804207
FLASH: MIL ILLUMINATION / DTC'S P2302, P2305, P2308, P2311, P2314 OR P2317. *NJ
2304106
EXTERIOR LAMP - LENS FOGGING. *NJ
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.