103954
Service Bulletin/Repair Instructions
ACTUATOR - A/C AND HEATER
Vehicle report
2008 DODGE AVENGER
Service bulletins
50 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
104087
Service Bulletin/Repair Instructions
ACTUATOR - A/C AND HEATER
9100226
Service Bulletin/Repair Instructions
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
9004009
Service Bulletin/Repair Instructions
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S1121000006 Rev.
Service Bulletin/Repair Instructions
(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
S1121000006RevA
Service Bulletin/Repair Instructions
(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
9004268
Service Bulletin/Repair Instructions
THROTTLE BODY For clarification, only use 68414676A$ on 2010 & earlier vehicles as supply is limited.
23-015-20
Service Bulletin/Repair Instructions
Disinfectant Solution Recommended for COVID-19
08-049-20
Service Bulletin/Repair Instructions
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
31-003-19
Service Bulletin/Repair Instructions
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-005-19
Service Bulletin/Repair Instructions
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Service Bulletin/Repair Instructions
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Service Bulletin/Repair Instructions
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100519
Service Bulletin/Repair Instructions
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Service Bulletin/Repair Instructions
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
9003220
Service Bulletin/Repair Instructions
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
9003687
Service Bulletin/Repair Instructions
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003681
Service Bulletin/Repair Instructions
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
68332810
Service Bulletin/Repair Instructions
Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m [21 ft. lbs.].
08-052-16
Service Bulletin/Repair Instructions
Flash: UConnect and Voice Recognition Inoperative This bulletin involves replacing the Hands Free Module (HFM). The customer may describe the following conditions: · A complete loss of UConnect operation. · A complete loss of Voice Recognition functionality
R2118796A
Service Bulletin/Repair Instructions
Valve Body. These may cause over drive cycling.
RL108213A$
Service Bulletin/Repair Instructions
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
9003215
Service Bulletin/Repair Instructions
Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
9002887
Service Bulletin/Repair Instructions
Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
9001645
Service Bulletin/Repair Instructions
Part Description: Short Runner Valve (Actuator) Issue Description: Issue 1~ JC,JS '08-09MY 3.5L only~ Caution - Do not replace the intake manifold for a short runner valve (SRV) fault (P1004 / P2008 / P2016 / P2017) or for a manifold tuning valve (MTV) fault (P1005 / P2077 / P2078). Instead follow the service procedure to investigate P codes associated with diagnosis of the SRV or MTV, then cycle the actuator using a diagnostic tool and verify that the PWM output is 50 (+ 2%) de-energized and 80 (+ 2 %) energized. If no problems observed, then idle the vehicle and verify the correct PWM output (50 + 2% PWM). Replace the actuator if you do not get the desired output. Issue 2~ If the SRV actuator or intake manifold is being replaced for a P1004 Short Runner Valve Performance fault code and the vehicle was built prior to 2/5/07 , technicians must complete the module reflash and verification test per TSB 18-003-07 REV. A to ensure the parts need to be replaced. Please reference TSB 18-003-07 REV. A for specific details on the procedure.
9001758
Service Bulletin/Repair Instructions
Part Description: Tonneau Extended/Retracted Switches Issue Description: Before replacing any of the convertible top micro switches and/or position sensors, please refer to the updated diagnostic tests for your specific DTC's. A physical check of the switch (resistance check, does it click, is the lever sticky, is the return spring present) will verify or eliminate that switch as the root cause of the vehicle's concern. RRT 07-025 only applies to vehicles built on or before June 22, 2007.~
9002519
Service Bulletin/Repair Instructions
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
09-001-13
Service Bulletin/Repair Instructions
Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
78
Service Bulletin/Repair Instructions
STAR Center News No. 78 - Jan/Feb 2013: Instead of limiting the use of the tether anchor to 48 pounds (child weight) the new guideline states that the tether anchor can be used with a seatbelt to install a child restraint up to the recommended weight limit of the child restraint.
21-006-12 REV. A
Service Bulletin/Repair Instructions
Vehicle Exhibits Vibration From The Transmission During Vehicle Launch (X43 Warranty Extension 5 Years 160,000 KMS) This bulletin involves replacing the clutch and damper assembly. The customer may experience a vibration feeling as they accelerate from a stop or accelerating while rolling at slow speeds. This condition could be caused by the damper and clutch.
CSN-K16
Service Bulletin/Repair Instructions
CHRYSLER DODGE SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. AUTOMATIC TRANSMISSION SHIFT LEVER INTERLOCK SPRING. TRANSMISSION GEAR SHIFT LEVER INTERLOCK SPRING RETAINER HOOK ON VEHICLES MAY BREAK. A BROKEN INTERLOCK SPRING RETAINER HOOK WILL RESULT IN THE INABILITY TO MOVE THE GEAR SHIFT LEVER OUT OF THE PARK POSITION. CSC LETTER WAS REC'D. *PE
SA-09-088
Service Bulletin/Repair Instructions
DODGE/CHRYSLER: RE-TORQUE DECKLID LATCH BOLTS. CERTAIN VEHICLES WERE SHIPPED WITH THE INCORRECT TORQUE ON THE DECKLID LATCH MOUNTING BOLTS AND WILL REQUIRE RE-TORQUE TO 10NM (88.50 IN LB). *PE
SB-J19
Service Bulletin/Repair Instructions
CHRYSLER/JEEP/DODGE: CALIFORNIA EMISSIONS WARRANTY ADDENDUM. THE WARRANTY BOOK ON CERTAIN VEHICLES MAY CONTAIN ERRORS OR MAY BE MISSING INFORMATION REGARDING THE COPONENTS COVERED BY THE CALIFORNIA EMISSIONS WARRANTY. DODGE-CARAVAN/GRAND CARAVAN, CHARGE/CHARGER SRT8, MAGNUM/MAGNUM SRT8, VIPER, AVENGER, NITRO, CHALLENGER/CHALLENGER SRT8, DURANGO/DURANGO HYBRID, JOURNEY, RAM 2500/3500, CALIBER/CALIBER SRT4; JEEP COMMANDER, GRAND CHEROKEE/GRAND CHEROKEESRT8, COMPASS, PATROIT, LIBERTY; CHRYSLER TOWN&COUNTRY, PACIFICA, 300 SRT8, PTCRUISER, SEBRING/SEBRING CONV., ASPEN/ASPEN HYBRID.
SB-1800309 REVC
Service Bulletin/Repair Instructions
CHRYSLER/JEEP/DODGE: FLASH-DRIVEABILITY IMPROVEMENTS OR MIL ILLUMINATION DIAGNOSTIC TROUBLE CODE P0452-EVAP PRESSURE SWITCH STUCK CLOSED. INCLUDES MY09 TOWN&COUNTRY; VOYAGER AND CARAVAN. *PE
1801108 REVB
Service Bulletin/Repair Instructions
FLASH: MIL ILLUMINATION WITH DTC P0139 OR 02270. THIS BULLETIN INVOLVES SELECTIVELY ERASING AND REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM). *PE
21-015-08
Service Bulletin/Repair Instructions
FLASH: TRANSMISSION ENGAGEMENT / PERFORMANCE IMPROVEMENTS. *NJ
H 11
Service Bulletin/Repair Instructions
CHRYSLER DODGE JEEP SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. CUSTOMER SATISFACTION NOTIFICATION H11; RADIO SOFTWARE UPDATE. THIS NOTIFICATION APPLIES ONLY TO VEHICLES EQUIPPED WITH A MYGIG RADIO (SALES CODE RER WITH NAVIGATION SYSTEM OR REN WITHOUT NAVIGATION SYSTEM). CSC WAS RECEIVED. *PE
08-039
Service Bulletin/Repair Instructions
DVD SOFTWARE UPDATE REN MYGIG RADIO FOR MANY RADIO FUNCTIONAL ISSUES AND IMPROVEMENTS. *NJ
08-016-08
Service Bulletin/Repair Instructions
ROUGH IDLE AND/OR MIL ILLUMINATION FOR ANY OF THE FOLLOWING DTC'S: P0300 / P0301 / P0302 / P0303 / P0304 / P0315 / P0335 AND/OR P0606. *NJ
08-031
Service Bulletin/Repair Instructions
DVD SOFTWARE UPDATE MYGIG RADIO FOR MANY RADIO FUNCTIONAL ISSUES AND IMPROVEMENTS. *NJ
08-023
Service Bulletin/Repair Instructions
RAPID RESPONSE TRANSMITTAL/SERVICE ACTION #08-023 - INCORRECT ENGINE HARNESS CRANK SENSOR CONNECTOR TERMINALS. *NJ
21-011-08
Service Bulletin/Repair Instructions
GEAR CLASH/DIFFICULT TO SHIFT - THIS BULLETIN INVOLVES REPLACING THE 3RD/4TH/5TH & REVERSE GEAR SYNCHRONIZER (BLOCKER) RINGS TOGETHER AS A SET IF A DE-BONDING CONDITION IS FOUND. *NJ
08-007-08
Service Bulletin/Repair Instructions
NO ENGINE CRANK OR NO ENGINE START DUE TO ELECTRONIC LOCKUP OF THE WCM/SKREEM. *NJ
2100308
Service Bulletin/Repair Instructions
FLASH: TORQUE CONVERTER SHUDDER WITH COORDINATED CHANGE OR SHIFT QUALITY IMPROVEMENTS. *NJ
07042
Service Bulletin/Repair Instructions
HOSE CLAMP FOR AIR FLOW SENSOR OUT OF POSITION. VEHICELS EQUIPPED WITH A 2.4L PZEV ENGINE. *NJ
2304106
Service Bulletin/Repair Instructions
EXTERIOR LAMP - LENS FOGGING. *NJ
0500407
Service Bulletin/Repair Instructions
FLASH ESP/TRACTION CONTROL SENSITIVITY ON TIGHT CURVES *NJ
23
Service Bulletin/Repair Instructions
EMISSIONS RECALL REPROGRAM TIPM - TRANSMISSION DEFAULT. TOTALLY INTEGRATED POWER MODULE (TIPM) WAS INADVERTANTLY PROGRAMMED WITH SOFTWARE THAT MAY PREVENT THE TRANSMISSION FROM SHIFTING PROPERLY. *KB
2100807
Service Bulletin/Repair Instructions
HARSH TRANSMISSION ENGAGEMENT OR CLUNK WHEN SHIFTING OUT OF REVERSE OR FROM DRIVE, THROUGH REVERSE INTO PARK. *KB
06
Service Bulletin/Repair Instructions
INCORRECT VEHICLE EMISSION CONTROL INFORMATION (VECI) LABEL INSTALLED. *KB
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.