Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
108463
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
108464
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
103239
AIR BAG - SIDE CURTAIN
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0815223
Fuel Pump Connector Replacement The technician may experience a crank/no start after the fuel pump module was replaced. This bulletin involves replacing the fuel pump connector harness (pigtail) when replacing the fuel pump module.
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003357A
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357a
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
9004557
Overhead Console If the sunglasses holder door in the overhead console will not stay closed, inspect the Latch for damage. The Latch is now released for service under part number 68599540A$.
S2208000131
No Start Condition After A Fuel Pump Replacement, Multiple Fuel System Level Related DTC?s Setting
2101214
Transmission Shift Enhancements - Adaptation Drive Learn Procedure
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
V51
Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
9004509
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
S1709000010
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
S1709000010 RevB
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
S1709000010RevB
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
0805517
This bulletin involves performing a USB service flash of the Hands Free Module.
S2008000113
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S2008000113 Rev.
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
9004361
NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission
S1709000010 Rev.
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S1508000480
Speed Control Operates Intermittently
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
08-083-19
Flash: Hands Free Module (HFM) Software Enhancements This bulletin involves reprogramming the HFM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL)illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: U0197-00 - Lost Communication With Hands Free Phone Module. Customers may also comment one or more the following: Loss of audio while on a Bluetooth phone call(MYs 2014 - 2019 JC Only). HFM does not boot properly. "Hands-Free Module Loading" is displayed on the head unit. The HFM is inoperative and unresponsive to all user input. The HFM is unresponsive and appears off the bus to wiTECH. Inaccurate foreign language translations. Voice Recognition (VR) is sluggish after changing the language. IPhone 4 starts auto recording itself. Background noise from automated speech recognition. When in Bluetooth Streaming Audio (BTSA) mode, the display will show ?Musicpaused connecting phone? while a song is being played and without an incoming call. Wrong BTSA screen when deleting. When in Text To Speech (TTS), it will be a mix of the TTS and recording. IPod touch, BTSA will not audio stream. Integrated center stack screen will display ?music paused? afterignition was cycled and BTSA was being used before the ignition was turned off. Automatic Sound Recognition (ASR) microphone picking up background noise. When the language is set for Italian and after the ignition is cycled,the phone screens will change to English(Sales Code RSQ Only). No response from the steering wheel VR button. Not being able to enter into the phone screen on the radio. The customer may note when trying to select a non-supported language likeRussian or Portuguese, the Hands Free screen will default to English. The VR will default back to the last language (Italian, French, Spanish,German or Dutch) the customer was using.
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
9004076
Oil Filter Adapter If replacing Oil Filter Adapter due to oil leak, please be aware a seal kit is available for repair. If replacing due to missing Spring Loaded Check Valve, a replacement spring and check valve are now available through MOPAR.
02-008-17
Servicing Lower Control Arm Inner Pivot Bushings This bulletin discusses replacement of the lower control arm inner pivot bushings.
08-055-17 REV. A
Flash: Hands Free Module Software Enhancements This bulletin involves reprogramming the Hands Free Module (HFM) with the latest available software. The customer may experience the following:HFM does not boot properly. "Hands-Free Module Loading" displayedon the head unit.TheHFM is inoperative and unresponsive to all user input.TheHFM is unresponsive and appears off the bus to wiTECH.Inaccurate foreign language translations.VoiceRecognition (VR) is sluggish after changing the language.IPhone®4 starts auto recording itself.Backgroundnoise from Automated Speech Recognition. When in Bluetooth® Streaming Audio (BTSA) mode, the display will show?Music paused connecting phone? while a song is beingplayed and without an incoming call. Wrong BTSA screen when deleting. Whenin Text To Speech (TTS), it will be a mix of the TTS and recording. IPod®touch, BTSA will not Audio Stream.Integratedcenter stack screen will display ?music paused? afterignition was cycled and BTSA was being used before the ignition wasturned off.AutomaticSound Recognition (ASR) Microphone picking up background noise.WithSales code RSQ, when the language is set for Italian and after theignition is cycled, the phone screens will change to English.No response from the VR button on the steering wheel.Notbeing able to enter into the phone screen on the radio.Technicians may find Diagnostic Trouble Code (DTC) U0197-00 Lost CommunicationWith Hands Free Phone Module, is set. Thecustomer may note when trying to select a non-supported language likeRussian or Portuguese, the Hands Free screen will default to English.The VR will default back to the last language (Italian, French, Spanish,German or Dutch) the customer was using.After the software update has been completed, both the hands free screen and VR will default back to the last language used.Enhancements now include all vehicles, not just internationalvehicles.The following software enhancement isincluded:VR Teleprompter
0805617
This bulletin involves performing a USB service flash of the Hands Free Module.
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003694
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
68140568A$
Steering Column If vehicle comes in for steering column replacement, verify column installed. Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other componenets to be replaced). For more information and details on PN's, see L-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.
Parts-3
Steering Column.
Z5091195A
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Z5091195A$
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
68277402A
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
08-031-16
Hands Free Module Prompts Begin Erroneously This bulletin involves diagnosing and based on outcome, either performing a USB flash or replacing the Mopar accessory Hands Free Module (HFM). A customer may experience the Uconnect prompts begin to play without pressing the Voice Recognition (VR) button. The prompt may repeat itself two or three times before exiting. The customer satisfaction enhancements are included with this software release. NOTE: After the HFM has been updated it will receive these enhancements: · Reduced ?Device Reading? wait time after connecting a device to the remote USB port. · Call / dial separation improves upon names being recognized as phone numbers. · Improved sound quality during Bluetooth streaming. · Increased iPod and iPhone compatibility. · SMS messaging support via Mobile Application Part (MAP) protocol (not all phones support the MAP protocol). · Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. · Previous button will return the song currently being played to the beginning of the track. · AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected. NOTE: USB mode resume will no longer 'resume' after ignition is OFF.
0803116
Hands Free Module Prompts Begin Erroneously.
RL108213A$
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
04584559A$
Steering Gears, Pumps and Hoses This tech tip applies to vehicles built before 12-23-2010, these vehicles can exhibit a squeak or rubbing noise when turning the steering wheel. Do not replace the steering gear, steering pump, power steering pressure hose or power steering return hose before investigating the dash seal ring. The source of the noise may be the sealing ring under the dash seal. To correct the issue apply MOPAR product part number 04318070AD (Silicone Spray Lube) to the inner dash seal interface and also the outer engine compartment interface. Do not use any alternate lubricants. If MOPAR product part number 04318070AD (Silicone Spray Lube) is not available then replace the assembly. Refer to TSB 08-091-14.
18-102-15
Flash: 6.4L Powertrain Diagnostic And System Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set in the PCM memory: ? U0140 - Lost Communication With Body Control Module (BCM) (Attempting to clear this DTC will be unsuccessful). ? P0573 - Brake Switch 1 Stuck Off.
1810215
Powertrain Diagnostic And System Enhancements.
10-002-15
Seat Belt Interaction With Police Equipment
18-067-15 REV A
Flash: PCM Software Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the Powertrain Control Module (PCM): ? U0140 - Lost Communication With Body Control Module. ? U0401 - Implausible Data Received From ECM/PCM. ? P0441 - Evap Purge System Performance. ? P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. This software update also has improvements for fuel pump relay cycling during remote starts.
1806715REVA
Flash: PCM Software Enhancements.
18-085-15
Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may describe hearing the fuel pump relay cycling during remote start or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM: ? U0140 - Lost Communication With Body Control Module (BCM). ? P06DD - Engine Oil Pressure Control Circuit Stuck Off. ? P0522 - Engine Oil Pressure Sensor Circuit Low. ? P0108 - Manifold Absolute Pressure Sensor Circuit High. ? P1239 - Engine Oil Temperature Too Low. ? P0298 - Engine Oil Temperature Too High.
1808515
This bulletin involves selectively erasing and reprogramming the Powertrain Control
18-067-15
Flash: PCM Software Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs) have been set: ? U0401-00 - Implausible Data Received From ECM/PCM ? P0441 - Evap Purge System Performance ? P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1 This software update also has improvements for fuel pump relay cycling during remote starts.
SB-18-067-15
2011-2012 DODGE CHALLENGER; 2012 DODGE CHARGER; 2012 CHRYSLER 300: MALFUNCTION INDICATOR LAMP ILLUMINATION. BULLETIN ON SELECTIVELY ERASING AND REPROGRAMMING POWERTRAIN CONTROL MODULE *CN
08-055-15 REV-A
RE2 RE3 RE6 RB4 RB5 RB6 Radio Enhancements This Bulletin involves updating the radio's software and if the vehicle is equipped with navigation (RB4, RB5 and RB6) the navigation software will also be updated. The customer may experience one or more of the following conditions: ? Improve FM radio reception. (This only applies to 2012 LX vehicles with RE6, RB6 radios located in Dubai). ? Audio muted after a cold start. This applies to all 2011 vehicles and only 2012 vehicles with software level earlier then 11.43.37. ? Phone screen buttons intermittently missing. ? Rear view camera screen may be blank. ? Improved rear view camera image. ? Radio presets and parameters returning to defaults. ? AM or FM audio mutes upon start up. ? Seek frozen, tuner locks up, unable to change stations (RE3 only). ? Radio resets (RE3 only). ? Presets are intermittently skipped (RE3 only). ? When playing MP3, iPod or USB songs, the screen will not always display the correct song title. ? Sirius Traffic/Weather Jump button improvement. ? Controls Screen popup time-out option has been added to settings screen (SRT only). ? Temperature and Oil pressure gauge enhancements (SRT only). ? Blind spot monitor chime enhancement. ? Radio Language Translation improvements. ? Navigation Language Translation improvements. ? Disable/Enable traffic announcement feature added (RB4 RB5 RB6). ? Garmin Voice Recognition (VR) enhancements (RB4 RB5 RB6). ? Garmin audio enhancements (RB4 RB5 RB6). ? Navigation map enhancements (RB4 RB5 RB6). ? Garmin stuck on loading screen (RB4 RB5 RB6). ? Traffic rerouting and icon enhancements (RB4 RB5 RB6). ? Incorrect map graphics on traffic circle (RB4 RB6 Right Hand Drive). ? Radio may reboot when Russian language keyboard used (RB4). ? Travel Link showing up as unsubscribed. ? Fuel Station routing issues. ? Heated seat greyed out. ? Navigation icon going backwards.
SB-08-055-15REVA
ON CERTAIN VEHICLES VARIOUS ISSUES PERTAINING TO BLANK REAR VIEW CAMERA SCREEN, PRESETS, INTERMITTENTLY SKIPPED, GREYED OUT HEATED SEAT, BACKWARDS GOING NAVIGATION ICON, ROUTING ISSUES WITH FUEL STATION, ETC. MODEL 2011-12 CHARGER, 300, JOURNEY. *PE
23-018-15
Rattle Or Buzzing Noise In Rear Shelf Area With Radio On Or While Driving On Bumpy Roads This bulletin involves modification or replacement of the backlite rear shelf. The customer may describe a rattle or buzz noise coming from the rear of the vehicle with the radio on or while driving on bumpy roads. This may be caused by the rear shelf moving relative to the backlite.
2301815
This bulletin involves modification or replacement of the backlite rear shelf
08-055-15
RE2 RE3 RE6 RB4 RB5 RB6 Radio Enhancements This Bulletin involves updating the radio's software and if the vehicle is equipped with navigation (RB4, RB5 and RB6) the navigation software will also be updated. The customer may experience one or more of the following conditions: ? Audio muted after a cold start. This applies to all 2011 vehicles and only 2012 vehicles with software level earlier then 11.43.37. ? Phone screen buttons intermittently missing. ? Rear view camera screen may be blank. ? Improved rear view camera image. ? Radio presets and parameters returning to defaults. ? AM or FM audio mutes upon start up. ? Seek frozen, tuner locks up, unable to change stations (RE3 only). ? Radio resets (RE3 only). ? Presets are intermittently skipped (RE3 only). ? When playing MP3, iPod or USB songs, the screen will not always display the correct song title. ? Sirius Traffic/Weather Jump button improvement. ? Controls Screen popup time-out option has been added to settings screen (SRT only). ? Temperature and Oil pressure gauge enhancements (SRT only). ? Blind spot monitor chime enhancement. ? Radio Language Translation improvements. ? Navigation Language Translation improvements. ? Disable/Enable traffic announcement feature added (RB4 RB5 RB6). ? Garmin Voice Recognition (VR) enhancements (RB4 RB5 RB6). ? Garmin audio enhancements (RB4 RB5 RB6). ? Navigation map enhancements (RB4 RB5 RB6). ? Garmin stuck on loading screen (RB4 RB5 RB6). ? Traffic rerouting and icon enhancements (RB4 RB5 RB6). ? Incorrect map graphics on traffic circle (RB4 RB6 Right Hand Drive). ? Radio may reboot when Russian language keyboard used (RB4). ? Travel Link showing up as unsubscribed. ? Fuel Station routing issues. ? Heated seat greyed out. ? Navigation icon going backwards.
07-002-15 REV. A
Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
9002887
Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
07-002-15
Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
09-002-14 REV. B
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire
0900214REVB
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire
0900214a
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire
02-007-14
Front End Clunk Noise When Coming To A Stop - Police Vehicles Only This bulletin involves replacing the left side or the right side or both side tension struts. Police vehicles with heavy duty suspension and rear wheel drive may experience a front end clunk noise, coming from the tension strut bushing(s), while coming to a stop.
02-008-14
Front End Clunk Noise When Coming To A Stop - Mexico Only This bulletin involves replacing both the left and right side front tension struts The customer may experience a front end clunk noise, coming from the tension strut bushing(s), when coming to a stop.
0200714
This bulletin involves replacing the left side or the right side or both side tension struts.
0200814
This bulletin involves replacing both the left and right side front tension struts.
21-033-14
FLASH: MIL Illumination For P0730 And Transmission Shift Enhancements This bulletin involves selectively erasing and reprogramming the Transmission Control Module (TCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find that Diagnostic Trouble Code (DTC) P0730 Incorrect Gear Ratio is setting erroneously. In addition to correcting the DTC, the following Transmission Control Module (TCM) calibration improvements are now available. These updates are broken down by vehicle line and engine category.WK, WD, JK and LC Vehicles equipped with a 3.6L engine (Sales Code ERB) Hanging in gear during HOT ambient temperature conditions while vehicle is loaded or towing. Delayed downshift during acceleration at speeds above 48 kph. (Taiwan, Japan, and China market only). Delayed downshift when driving at altitudes higher than 2500 feet. Inconsistent shifting when towing or while driving up or down steep hills. Delayed upshift while driving in 4 low Intermittent delayed shift. Delayed engagement when shifting from drive to reverse while in 4 low. (JK Rubicon only) Delayed shift from second gear while towing or driving on steep grades. (JK Rubicon only) Intermittent delayed engagement from reverse to drive. Less than desired shift quality in AutoStick mode. (LC vehicles only) Fuel economy improvements. (LC vehicles only)LC Vehicles equipped with a 5.7L engine (Sales Codes EZH or EZC) Hanging in gear during HOT ambient temperature conditions while vehicle is loaded or towing. Bump sensation felt during deceleration or braking. Fuel economy improvements.LC and WK Vehicles equipped with a 6.4L engine (Sales Codes ESH or ESG) Bump sensation felt during deceleration or braking. (LC only) Inconsistent downshift during Wide Open Throttle (WOT) accelerations at highway speeds (i.e. passing). Transmission enhancements to improve acceleration while in reverse going uphill on steep
2103314
MIL Illumination For P0730 And Transmission Shift Enhancements
09-002-14 REV. A
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire
0900214
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension)
21-012-14 REV. B
8 Speed Transmission Shift Adaptation, Drive Learn Procedure This bulletin involves performing a Transmission Adaptation Learn procedure based on a subjective shift quality rating evaluation.The adaptation drive learn procedure must be performed on all 8-speed transmissions when the transmission is repaired/replaced and/or the Valve Body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.
08-040-14 REV. A
Police Vehicle A/C Inoperative This bulletin involves relocating the A/C fuse within the front Power Distribution Center (PDC). Customer comments A/C is warm. On further inspection the technician will notice the A/C clutch fuse is loose in its cavity (#12) in the PDC. This will cause a poor connection and the fuse cavity to be distorted.
08-040-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
0804014
Police Vehicle A/C Inoperative This bulletin involves relocating the A/C fuse within the front Power Distribution Center (PDC). Customer comments A/C is warm. On further inspection the technician will notice the A/C clutch fuse is loose in its cavity (#12) in the PDC. This will cause a poor connection and the fuse cavity to be distorted.
08-028-14 REV. A
RE2 RE3 RE6 RB4 RB5 RB6 Radio Enhancements This Bulletin involves updating the radio's software and if the vehicle is equipped with navigation (RB4, RB5 and RB6) the navigation software will also be updated. The customer may experience one or more of the following conditions: Phone screen buttons intermittently missing. Rear view camera screen may be blank. Improved rear view camera image. Radio presets and parameters returning to defaults. AM or FM audio mutes upon start up. Seek frozen, tuner locks up, unable to change stations (RE3 only). Radio resets (RE3 only). Presets are intermittently skipped (RE3 only). When playing MP3, iPod or USB songs, the screen will not always display the correct song title. Sirius Traffic/Weather Jump button improvement. Controls Screen popup time-out option has been added to settings screen (SRT only). Temperature and Oil pressure gauge enhancements (SRT only). Blind spot monitor chime enhancement. Radio Language Translation improvements. Navigation Language Translation improvements. Disable/Enable traffic announcement feature added (RB4 RB5 RB6). Garmin Voice Recognition (VR) enhancements (RB4 RB5 RB6). Garmin audio enhancements (RB4 RB5 RB6). Navigation map enhancements (RB4 RB5 RB6). Garmin stuck on loading screen (RB4 RB5 RB6). Traffic rerouting and icon enhancements (RB4 RB5 RB6). Incorrect map graphics on traffic circle (RB4 RB6 Right Hand Drive). Radio may reboot when Russian language keyboard used (RB4). Travel Link showing up as unsubscribed. Fuel Station routing issues. Heated seat greyed out. Navigation icon going backwards.
08-028-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
0802814
RE2 RE3 RE6 RB4 RB5 RB6 Radio Enhancements This Bulletin involves updating the radio's software and if the vehicle is equipped with navigation (RB4, RB5 and RB6) the navigation software will also be updated. The customer may experience one or more of the following conditions: Phone screen buttons intermittently missing. Rear view camera screen may be blank. Improved rear view camera image. Radio presets and parameters returning to defaults. AM or FM audio mutes upon start up. Seek frozen, tuner locks up, unable to change stations (RE3 only). Radio resets (RE3 only). Presets are intermittently skipped (RE3 only). When playing MP3, iPod or USB songs, the screen will not always display the correct song title. Sirius Traffic/Weather Jump button improvement. Controls Screen popup time-out option has been added to settings screen (SRT only). Temperature and Oil pressure gauge enhancements (SRT only). Blind spot monitor chime enhancement. Radio Language Translation improvements. Navigation Language Translation improvements. Disable/Enable traffic announcement feature added (RB4 RB5 RB6). Garmin Voice Recognition (VR) enhancements (RB4 RB5 RB6). Garmin audio enhancements (RB4 RB5 RB6). Navigation map enhancements (RB4 RB5 RB6). Garmin stuck on loading screen (RB4 RB5 RB6). Traffic rerouting and icon enhancements (RB4 RB5 RB6). Incorrect map graphics on traffic circle (RB4 RB6 Right Hand Drive). Radio may reboot when Russian language keyboard used (RB4). Travel Link showing up as unsubscribed. Fuel Station routing issues. Heated seat greyed out. Navigation icon going backwards.
21-012-14 REV. A
Transmission Shift Enhancements - Adaptation Drive Learn Procedure This bulletin involves performing a subjective shift quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.
21-012-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
9003103
Part Description: Fuel Pump Module Issue Description: This TechTip applies to ONLY Charger (LD) 2011 thru 2014MY vehicles equipped with sales code AHB- Police Group. For vehicles operating under excessive idling condition an alternative high performance pump is available if the customer prefers. Part number 68103913AB or 68145815AA when used with XDC- Fuel Tank
09-002-14
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire
9003081
Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.
08-040-14
Police Vehicle A/C Inoperative This bulletin involves relocating the A/C fuse within the front Power Distribution Center (PDC). Customer comments A/C is warm. On further inspection the technician will notice the A/C clutch fuse is loose in its cavity (#12) in the PDC. This will cause a poor connection and the fuse cavity to be distorted.
21-012-14
Transmission Shift Enhancements - Adaptation Drive Learn Procedure This bulletin involves performing a subjective shift quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.
08-028-14
RB5 RE2 RE6 RB6 RE3 RB4 Radio Enhancements This Bulletin involves updating the radio's software. A customer may experience one or move of the following: ? Fuel Station Routing issues. ? Heated Seat Greyed Out. ? Navigation Icon going backwards. ? Map Checksum Error.
P08030614
New Safety Recall Advanced Communication ? P08030614 Chrysler Group LLC (Chrysler) announced a safety recall on certain 2011 and 2012 model year (LD) Dodge Charger vehicles. The headlight wiring harness connectors may overheat. This could cause a loss of low beam headlight function without warning. A loss of headlight(s) during nighttime driving could cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspected, and replaced if necessary, the headlight wire harnesses. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. Chrysler anticipates the launch of this safety recall in April 2014. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.
CSN-P-01
DODGE/CHRYSLER: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. DUE TO AN ENGINE FRACTURED TIMING CHAIN GUIDE, THE TIMING CHAIN IN ENGINE WILL BREAK AND WOULD RESULT IN SEVERE DAMAGE TO THE ENGINE. MODEL 2009-2012 CHALLENGER, CHARGER, 300. *PE
08-011-14
Flash: Hands Free Module Defaults To English Instead Of Last Language Selected This Bulletin involves performing a USB service flash of the Hands Free Module (HFM). The customer may note when trying to select a none supported language like Russian or Portuguese the Hands Free screen will default to English. The Voice Recognition (VR) will default back to the last language (Italian, French, Spanish, German or Dutch) the customer was using. After the software updated has been completed both the Hands Free screen and VR will default back to the last language used. VR Teleprompter enhancement.
08-084-13REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-084-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-046-13REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-059-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-050-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
21-005-13
FLASH: MIL Illumination For P0730 - Incorrect Gear Ratio This bulletin involves updating the Transmission Control Module (TCM) software. Customers may indicate that the MIL is illuminated and/or the transmission went into limp-in. Upon further investigation, Diagnostic Trouble Code (DTC) P0730 - Incorrect Gear Ratio is either active or stored in the PCM?s memory.
08-033-13
Flash: Two Or More Speakers Will Mute When Playing Certain Media Sources This bulletin involves reprogramming the Amplifier with updated software. The customer may experience two or more speakers muting when playing certain media sources, which have frequencies of less then 20 Hz. The speakers will stay muted until the ignition key is cycled. On further inspection the technician will find speaker performance DTC's. B1460-92Channel 1 Audio Speaker Output-Performance or Incorrect Operation. B1465-92Channel 2 Audio Speaker Output-Performance or Incorrect Operation. B146A-92Channel 3 Audio Speaker Output-Performance or Incorrect Operation. B146F-92Channel 4 Audio Speaker Output-Performance or Incorrect Operation. B1474-92Channel 5 Audio Speaker Output-Performance or Incorrect Operation. B1479-92Channel 6 Audio Speaker Output-Performance or Incorrect Operation. B147E-92Channel 7 Audio Speaker Output-Performance or Incorrect Operation. B1483-92Channel 8 Audio Speaker Output-Performance or Incorrect Operation. B14B9-92Channel 9 Audio Speaker Output-Performance or Incorrect Operation. B14BE-92Channel 10 Audio Speaker Output-Performance or Incorrect Operation. B14C3-92Channel 11 Audio Speaker Output-Performance or Incorrect Operation. B14C8-92Channel 12 Audio Speaker Output-Performance or Incorrect Operation. B221F-00Amplifier Internal.
08-032-13
Flash: No Audio From The Radio Caused By The Amplifier Not Communicating This bulletin involves re-flashing the Amplifier with updated software. The customer may indicate that there is no audio and/or radio is muted. This condition may be caused by the amplifier not communicating on the bus.Flashing the amplifier will correct this condition.
18-020-13
Flash: Erroneous P0573- Brake Switch 1 Stuck Off This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software to eliminate the potential of setting this erroneous Diagnostic Trouble Code. Technician may find that the following erroneous Diagnostic Trouble Code has been set: P0573 - Brake Switch 1 Stuck Off
SB-18-020-13
CHRYSLER/DODGE: SOFTWARE UPDATE TO ELIMINATE THE ERRONEOUS TROUBLE CODE OF P0573 FOR THE BRAKE SWITCH. *KB
9002900
Part Description: Switch-Padedle Down Audio LT. Switch-Paddle Up Audio RT. Issue Description: When traveling over bumpy roads, a high pitched ringing/bell sound may come from the left or right paddle switch's in the steering wheel. If this noise is heard, replace both Left and Right Paddle switch.
23-016-13
This bulletin involves replacing the power seat track drive block bolts on front driver and/or passenger seat. The customer may experience up to 1mm(1/32?) fore/aft movement of the driver and/or passenger seat during acceleration and/or braking.
N07040413
The above vehicles may have been built with front seat airbag wire harnesses with improper sized terminal crimp(s) that may cause an intermittent airbag warning light.
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
9002838
04627731A$ - Trans Vent Hose The upper end of the transmission vent hose terminates with an open elbow. There is no cap on the end of the vent hose. This is intentional. Some graphics in StarParts may show a vent hose including a cap, but this is incorrect. The actual production vent hose has an open elbow fitting, not a cap. The elbow should be pointing downwards in the vehicle.~
08-009-13
RB6 RB5 Navigation Radio Locks Up All Of The Navigation Functions This Bulletin involves replacing the Telematics Gateway Module (TGM) RB5 or RB6. A customer may experience that the Navigation radio locks up, and both of the navigation voice and display stops working. The user will be locked out of all navigation functions.Replacing the Telematics Gateway Module (TGM/TGW) will repair this condition.All radio and navigation functions are controlled by the TGM.
08-007-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
09-001-13
Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
9002524
Customer complains of inaccurate navigation routing, vehicle indicator drifting from the given route and/or navigation resets. To fix this customer issue, the following must be performed in accordance to TSB 08-004-13.
9002827
Customer complains of inaccurate navigation routing, vehicle indicator drifting from the given route and/or navigation resets. To fix this customer issue, the following must be performed in accordance to TSB 08-004-13:~
18-031-12 REV. A
Flash: MIL Illumination P0108 - Manifold Absolute Pressure Sensor Circuit High This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that P0108 - Manifold Absolute Pressure Sensor Circuit High has been set active or stored.Updating the software will correct the condition listed above.
18-031-12REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
19-003-12
Police Vehicle Power Steering Overheat During Closed Course Training Exercises This bulletin involves installing an external power steering cooler on the involved police fleet vehicles. The police fleet may experience increased steering efforts or power steering overheat during extended periods of extreme closed course handling maneuvers while conducting training exercises in ambient temperatures above 100° F (38° C). Diagnostic Trouble Code C2210-00 - ECU over temp may be present.
SB-19-003-12
DODGE: WHILE CONDUCTING CLOSED TRAINING COURSE EXERCISES, POWER STEERING, IN POLICE VEHICLES, WOULD OVER HEAT, IN AMBIENT TEMPERATURES, CAUSING HANDLING MANEUVERS DIFFICULT. MODELS 2011-2012 CHARGER. *PE
08-032-12 REV. A
Flash: No Audio From The Radio Caused By The Amplifier Not Communicating This bulletin involves re-flashing the Amplifier with updated software. The customer may indicate that there is no audio and/or radio is muted. This condition may be caused by the amplifier not communicating on the bus.Flashing the amplifier will correct this condition.
08-032-12REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
18-031-12
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
02-006-12
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
CSN-M30
DODGE/CHRYSLER: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. INTERNAL TEMPERATURE TOO HIGH DIAGNOSTIC FAULT CAUSES PERMANENT MALFUNCTION INDICATOR LAMP (MIL) TO ILLUMINATE DUE TO INADVERTENTLY PROGRAMMING SOFTWARE TO NOT RUN POSITION VALVE STUCK DIAGNOSTICS OR PERMANENTLY SET INTERNAL TEMPERATURE. MODEL 2012 CHARGER, 300. *PE
SB-02-005-12
DODGE: WHEN COMING TO A STOP, FRONT END MAKES CLUNKING NOISE CAN BE HEARD COMING FROM TENSION STRUT BUSHINGS. MODELS 2011-2012 CHARGER/CHARGER EXPORT. *PE
CSN-M-15
DODGE: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. UNDER CERTAIN DRIVING CONDITIONS, TIRE PRESSURE MONITOR SENSORS (TPMS) MAY LEAK AIR. ALSO, INSTRUMENT PANEL CONTROL (IPC) AND BODY CONTROL MODULE (BCM), WHILE IN STEALTH MODE, NEEDS REPROGRAMMING TO CORRECT PANEL BRIGHTNESS. *PE
22-002-12
CHRYSLER: STEERING WHEEL VIBRATION AT HIGHWAY SPEEDS. THIS BULLETIN INVOLVES ROAD TESTING, TIRE BALANCING, ROAD FORCE VARIATION AND IF NECESSARY CONTACTING STAR FOR VEHICLES LESS THAN 12,000 MILES. MODEL CHARGER MODEL YEARS 2011-2012 *JS
SB-21-007-12
CHRYSLER/DODGE: WHEN SHIFTING TRANSMISSION, WOULD EXPERIENCE A SHUDDER, HARSH SHIFTING OR A LAUNCH AND MIL WOULD ILLUMINATE. *PE
CSN-M-04
DODGE/CHRYSLER/JEEP: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. IN MANUAL (USER GUIDE), STATED INCORRECTLY ENGINE OIL (SAE 5W-40), INSTEAD OF CORRECTLY ENGINE OIL (SAE 0W-40 FULL SYNTHETIC ENGINE OIL. *PE
CSN-M-08
CHRYSLER/DODGE: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. WHILE DRIVING AT NIGHT, THE GEAR SHIFT INDICATOR LIGHT ON INSTRUMENT PANEL, SHINES BRIGHTER THAN OTHER COMPONENTS. *PE
WB-D-12-10
CHRYSLER/DODGE: A VIP LOP RESTRICTION PROGRAM INTRODUCED IN AN EFFORT TO MONITOR AND CORRECT QUALITY ISSUES IN TIMELY AND EFFICIENT MANNER FOR HANDS FREE MODULE (HFM). *PE
08-001-12
CHRYSLER/DODGE: TEMPORARY LOSS OF ABS/ESP FUNCTIONALITY. ABS/ESP LAMP MIGHT ILLUMINATE. *KB
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.