101232
Service Bulletin/Repair Instructions
Plate - Planetary
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
101232
Plate - Planetary
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
9001784
Mechanical rocker arm, intake, 1.7 ratio.
9004275
KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
1807717
Connecting to the DRB III Emulator for Cummins Engines
68332810
Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m [21 ft. lbs.].
68332810A
Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only.
R2118796A
Valve Body. These may cause over drive cycling.
RL108213A$
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
9003215
Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
9002887
Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
9002828
Part Description: Insulator in Lever Assembly - Valve Body - Trans Issue Description: The manual valve insulator, attaching rivet and an instruction sheet are now available as a kit. If the insulator requires replacement lease order 68253099AA. Note: Insulator color is not relevant for service
18-042-14
Generic Powertrain Control Module (PCM) Procedure This bulletin involves programming a generic PCM with software.
9002054
If replacing the steering linkage or drag link inner tie rod assembly at the pitman arm on a vehicle built before Febuary 14 th, 2008, verify that the pitman arm part number is 68039930AA. The part number is embossed on the pitman arm.~If the pitman arm is not a 68039930AA, it must be replaced with a 68039930AA.~ Issue 2: For 2003 to 2007 MY only. If the OE steering linkage has been replaced with 52122362AA, 52122362AB, 52122362AC, 52122362AD, 52122362AE, or 52122362AF and pitman arm 68039930AA the following service parts are available.
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
08-010-13
Fluid Leak From Washer Reservoir (X44 Warranty Extension 5 Years/100,000 Miles (160,000 KMS)) This bulletin involves inspecting and/or replacing the washer reservoir. A customer may have a condition where fluid is leaking from the washer reservoir. On further inspection the technician may find cracks in the reservoir by the washer pump pocket.
9001745
05174039A$, 05072384A$, 05072138A$ - A/C Pressure Transducer For vehicles calling out AC Pressure Transducer Kit 05072138AA as a service part but built with different mating wiring connector (round) - also order connector repair kit 05019958AA (square).~ 2007MY RAM Trucks equipped with 6.7L Cummins turbo diesel engine only: If the A/C pressure transducer requires replacement, use part number 05072138AA that has a rectangular shaped electrical connector. If the engine wiring harness has a circular wiring connector, use jumper harness 68028774AA to change it to a rectangular connector.~ 6.7L RAM trucks built before10/17/2006 has pressures transducers (p/n 05191766AA) with a round connector that should have been changed per RRT 06- 068 to a rectangular transducer.~ 2001-2008 KJ, K1, ND.~
9002688
68069384A$, R8069384A$, 68086182A$, R8027067A$, RL002012A$ - Gasket, Cylinder Head Cover Before replacing injectors for Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.~
08-004
2003-2008 (DR) RAM TRUCK 1500-STEERING SHUDDER DURING PARKING LOT OR LOW VEHICLE SPEED MANEUVERS. *PE
1900805
REVISED POWER STEERING SYSTEM BLEEDING PROCEDURES. *SC
2401305
AIR CONDITIONING (A/C) COOLING COIL ODOR. *TT
2101205
NEW 42RLE VARIABLE LINE PRESSURE TRANSMISSION (VLP). *TT
1400305
CUMMINS DIESEL DIAGNOSTICS. *TT
1400405
ELECTRONIC FUEL CONTROL (EFC) ACTUATOR AVAILABLE FOR SERVICE. *TT
1901204
STEERING COLUMN SNAPPING OR TICKING SOUND. *TT
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.