Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 54601
Service Bulletin/Repair Instructions
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
SSM 54366
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
SSM 53176
Service Bulletin/Repair Instructions
Some 2013-2016 Escape vehicles may exhibit an ABS warning indicator with diagnostic trouble code (DTC) U2300 after the ABS module is replaced.
SSM 53040
Service Bulletin/Repair Instructions
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
SSM 52476
Service Bulletin/Repair Instructions
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
SSM 52335
Service Bulletin/Repair Instructions
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 51536
Service Bulletin/Repair Instructions
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
SSM 51261
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 51181
Service Bulletin/Repair Instructions
Some 2013-2016 Escape/Fusion/MKZ vehicles may display an error message when updating the All Wheel Drive-ATC Barcode using the IDS service function after installing a new rear drive unit assembly (RDU) or active torque coupling (ATC) clutch assembly. To prevent this error from occurring, enter the universal ATC 4 digit barcode 7772. Once programmed, perform several figure 8 turns at parking lot speeds to verify there is no binding from the all wheel drive (AWD) system. If the vehicle binds in a turn, perform Pinpoint Test A. Refer to the Workshop Manual (WSM), Section 308-07A > Diagnosis and Testing.
SSM 51120
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 50804
Service Bulletin/Repair Instructions
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
TSB 22-2066
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
TSB 22-2104
Service Bulletin/Repair Instructions
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 50067
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 50064
Service Bulletin/Repair Instructions
Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
TSB 21-2236
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 49821
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-2152
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
TSB 21-2033
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2013-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and install the protective cap over the selector at the transmission end of the selector lever cable.
SSM 49210
Service Bulletin/Repair Instructions
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
TSB 20-2171
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 48619
Service Bulletin/Repair Instructions
SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
SSM 48423
Service Bulletin/Repair Instructions
Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 48397
Service Bulletin/Repair Instructions
Some 2013-2015 Fusion/MKZ/Escape/MKC with a 1.6L GTDI, 1.5L GTDI, or 2.0L GTDI may exhibit a lack of power, loss of power, or stall when placed in gear with DTCs P00C6, P0087, P008A, P008B, P018C, or P018D. If normal diagnosis leads to a biased or failed Fuel Low Pressure (FLP) sensor, the sensor is available without the need to order the entire fuel line assembly. The FLP sensor, located on the fuel supply line to the high pressure pump, provides the low side fuel pressure input to the PCM so the Fuel Driver Module can be controlled accordingly. The FLP PID can be viewed in the Datalogger and then compared to a manual pressure gauge per pinpoint test HC in the PCED to validate the sensor is working properly. The Fusion/MKZ catalog has been updated to show the sensor availability.
TSB 19-2287
Service Bulletin/Repair Instructions
Some 2013-2016 Escape vehicles equipped with a 1.6L EcoBoost engine may exhibit a lack of cooling caused by the A/C inlet line breaking at the compressor. This may be due to the oil cooler coolant lines exerting excess pressure on the A/C inlet line. When replacing the A/C inlet line, a support clip for the oil cooler coolant line should be installed to prevent contacting the A/C inlet line. To correct the condition, follow the Service Procedure steps to replace the A/C inlet line and adjust the gap between the A/C inlet line and the CAC hose.
SSM 48135
Service Bulletin/Repair Instructions
Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 48130
Service Bulletin/Repair Instructions
Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
SSM 48123
Service Bulletin/Repair Instructions
For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
TSB 19-2172
Service Bulletin/Repair Instructions
Some 2015-2018 Edge and 2015-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
SSM 47976
Service Bulletin/Repair Instructions
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 47850
Service Bulletin/Repair Instructions
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 47948
Service Bulletin/Repair Instructions
SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
TSB 19-2100
Service Bulletin/Repair Instructions
Some 2013-2015 Escape vehicles equipped with a 1.6L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) and/or a transmission malfunction service now warning with only diagnostic trouble codes (DTCs) P0741 and/or P1744 stored in the powertrain control module (PCM). This may be due to internal damage to the torque converter. To resolve the condition, repair or replace the affected internal transmission components as directed by the Service Procedure.
SSM 47875
Service Bulletin/Repair Instructions
Some 2014-2019 Escape, 2014-2018 C-MAX, Focus, and Transit Connect vehicles not equipped with an auto start/stop system may exhibit an inability to program and/or no electrical power after installation of a service part body control module (BCM). Inspect the BCM for the presence of fuse F88. If fuse 88 is missing, install a 25 amp fuse and then re-evaluate the concern. If fuse 88 is installed in a vehicle with an auto start/stop system, the vehicle may exhibit concerns where the radio is turning off during an auto start/stop event and the instrument panel cluster (IPC) back lighting slowly goes dim during auto start/stop events.
SSM 47858
Service Bulletin/Repair Instructions
Some 2013-2018 Escape vehicles may exhibit damaged or delaminated bushing(s) on the rear suspension front lower arm (dog bone). If the rear suspension front lower arm requires replacement, an updated part is available through the parts catalog. Refer to Workshop Manual (WSM), Section 204-02 for removal and installation.
SSM 47824
Service Bulletin/Repair Instructions
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
TSB 19-2017
Service Bulletin/Repair Instructions
Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
SSM 47749
Service Bulletin/Repair Instructions
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
SSM 47710
Service Bulletin/Repair Instructions
Some 2014-2015 Escape, 2015 C-Max and Focus vehicles equipped with integrated remote start may exhibit an illuminated MIL with diagnostic trouble code (DTC) P0116 in the powertrain control module (PCM) immediately following a remote start event. Vehicles may also display a warning message stating Engine Coolant Over Temperature. This condition may occur when remote start is used and the vehicle is allowed to time out (engine shuts off). Reprogram the body control module (BCM) using the latest software version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 12A648 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 47703
Service Bulletin/Repair Instructions
Some 2014-2019 Escape, 2014-2018 C-MAX,Focus, and Transit Connect vehicles may exhibit a concern of not able to program and/or no electrical power after installation of a service part Body Control Module(BCM). Inspect the BCM for the presence of fuse F88. If the fuse is missing, install the correct size replacement fuse as outlined in the Wiring Manual and then re-evaluate the concern.
TSB 18-2361
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
SSM 47678
Service Bulletin/Repair Instructions
2013-2019 Escape and 2015-2019 MKC vehicles equipped with a power roof opening panel will exhibit a small vent opening position of 5 mm (.197 in). This is the normal vent position for optimal noise, vibration, harshness (NVH) and windnoise qualities. When the vent is closed, the front sliding glass panel will open to the 10 mm (.394 in) position and then close. The front sliding glass panel also opens to the 10 mm (.394 in) position to give the front sliding glass panel enough clearance before it opens to the rearward position. This is a normal operating characteristic of the front sliding glass panel. No repairs are required.
SSM 47662
Service Bulletin/Repair Instructions
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 47634
Service Bulletin/Repair Instructions
Some 2013-2019 Escape and 2015-2019 MKC vehicles may exhibit a vibration attributed to the tires. Prior to performing any road force balancing procedures or related diagnosis, make sure the vehicle tire pressure is correct and is driven a minimum of 24 Km (15 miles) to eliminate any possible flat spotting conditions and potential misdiagnosis. Refer to Workshop Manual (WSM), Section 204-04A for further information. In addition, it is recommended that diagnosis of tire/wheel vibration should not be performed on tires with less than 320 Km (200 miles). Some initial tire/wheel vibration issues (such as flat spotting) may correct themselves after the tires have been in service for 320 Km (200 miles). Setting tire pressure to the correct placard pressure is contained within pre-delivery inspection.
TSB 18-2314
Service Bulletin/Repair Instructions
Some 2013-2016 Escape vehicles equipped with a 1.6L EcoBoost engine may exhibit a lack of cooling caused by the A/C inlet line breaking at the compressor. This may be due to the oil cooler coolant lines exerting excess pressure on the A/C inlet line. When replacing the A/C inlet line, a support clip for the oil cooler coolant line should be installed to prevent contacting the A/C inlet line. Follow the Service Procedure to correct the condition.
SSM 47508
Service Bulletin/Repair Instructions
Some 2014-2018 Escape vehicles may exhibit a concern of not able to program and/or no electrical power after installation of a service part BCM. Inspect the BCM for the presence of fuse F88. If the fuse is missing, install the correct size replacement fuse as outlined in the Wiring Manual and then re-evaluate the concern.
TSB 18-2255
Service Bulletin/Repair Instructions
Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.
SSM 47462
Service Bulletin/Repair Instructions
2015-2018 Edge, Fusion, Focus, MKZ, MKC, Escape vehicles equipped with a 2.0L EcoBoost engine may exhibit coolant consumption, white smoke and/or a runs rough condition. Refer to the extended coolant pressure test and checking for combustion gases in Workshop Manual (WSM), Section 303-03A. If internal coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect the cylinder block and head for erosion, pitting, and flatness defects, primarily between the cylinder to cylinder bore bridges. If defects to the aluminum surface on the cylinder block and/or cylinder head are found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01A for the repair procedures
SSM 47430
Service Bulletin/Repair Instructions
If a trailer hitch receiver is installed on a 2013-2018 Escape or 2015-2019 MKC vehicle equipped with a hands-free liftgate, the hands-free liftgate function will become inoperative. Hands-free liftgate function can be restored by replacing the existing hands-free liftgate actuation upper sensor (14F680), lower sensor (14F680), stone deflector (17779), hands-free liftgate actuation module (14B291), plastic fasteners (N807951S) and screws (W506964) that are required for the factory installed trailer hitch receiver with hands-free liftgate option. Replacement of these parts to restore hands-free liftgate function is not warrantable. Regardless of trailer hitch configuration, the hands-free liftgate system cannot be added to a vehicle that was originally built without the hands-free liftgate option.
SSM 47416
Service Bulletin/Repair Instructions
Some 2013-2018 Escape vehicles may exhibit damaged or delaminated bushing(s) on the rear suspension front lower arm (dog bone). If the rear suspension front lower arm requires replacement, an updated part BV6Z-5500-D with a solid bushing is available. Refer to Workshop Manual (WSM), Section 204-02 for removal and installation.
SSM 47234
Service Bulletin/Repair Instructions
Some 2013-2016 Escape and 2016 Focus, Transit and Transit Connect vehicles equipped with a front control display interface module (FCDIM) may exhibit the inability to store AM/FM presets, select AM/FM presets and/or erratic preset button operation. Reprogram the front control display interface module (FCDIM) using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 109.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards(SLTS) manual.
SSM 47228
Service Bulletin/Repair Instructions
Some 2015-2017 Escape vehicles built on or before 5-Apr-2017 with factory trailer tow may exhibit a concern with a trailer lamp out warning and/or BLIS not available warning without a trailer connected. Access connectors C439 (4 pin) and C432 (12 pin) in the trailer tow harness. Inspect for corrosion and/or water contamination. Clean as required and add electrical grease (XG-12). Install and fully seat cover on C439 to prevent future water entry. Reprogram the trailer module (TR) using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 105.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 15K868 and applicable labor operations in Section 10 of the SLTS Manual, use causal part 19H332 for reprogram.
SSM 47201
Service Bulletin/Repair Instructions
Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
SSM 47204
Service Bulletin/Repair Instructions
Some 2015-2018 Fusion/MKZ/MKC/Escape/Edge vehicles equipped with a 2.0L EcoBoost engine may exhibit a runs rough condition with DTCs P0300, P0301, P0302, P0303, P0304 and/or P0316. This may be due to coolant intrusion due to corrosion on the engine block. To diagnose this concern, with the engine at normal operating temperature, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If the coolant pressure drops 27.57 kPa (4psi), remove the spark plugs and inspect for coolant in the cylinders. If coolant is found in any of the cylinders, replace the engine long block assembly. Follow normal prior approval process for your Dealership. However, follow the diagnostic repair procedure in this article to determine correct repair. For claiming, use causal part 6006 and applicable labor operations in Section 6 of the SLTS Manual.
SSM 47080
Service Bulletin/Repair Instructions
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
SSM 47009
Service Bulletin/Repair Instructions
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
SSM 47000
Service Bulletin/Repair Instructions
Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
SSM 46937
Service Bulletin/Repair Instructions
Some 2013-2016 Escape vehicles equipped with a 1.6L EcoBoost engine may require the replacement of the A/C suction line. When replacing the suction line, verify that all of the compressor to engine block fasteners are installed and torqued properly. The compressor requires three fasteners - 2 bolts (W701331-S442) and one stud/nut - installed securing it to the engine block and torqued to 25 Nm (18 lb.ft) per the Workshop Manual (WSM), Section 412-00 under removal and installation. Improper number of compressor fasteners and/or incorrect torque may cause repeat failure of the A/C suction line connected to the compressor.
17-2218
Service Bulletin/Repair Instructions
Some 2013-2018 Escape, Focus and C-Max vehicles may exhibit a water stained headliner after the vehicle has experienced a water leak from areas such as the roof opening panel, fixed glass, roof rails and roof ditch mouldings. Follow the procedure below to remove the water stains from the headliner after the water leak has been repaired. Follow the Service Procedure steps to correct the condition.
SSM 46900
Service Bulletin/Repair Instructions
Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
SSM 46862
Service Bulletin/Repair Instructions
Some owners of 2013-2018 Escape vehicles may complain of the rear license plate viewed in the lower portion of the display screen when using the parking aid camera. This is due to the convex camera lens to provide as much viewing angle as possible. This is a normal vehicle characteristic and no repairs or adjustments should be attempted to correct this condition.
SSM 46703
Service Bulletin/Repair Instructions
Some 2013-2017 Edge/MKX/Escape/MKC/Fusion/MKZ/Flex/MKT/Mondeo/Kuga/EcoSport AWD vehicles where diagnosis leads to a RDU clutch issue, a rear drive unit (RDU) service kit is available. Use the vehicle identification number (VIN) in the parts catalog to look for base part 4A232. If clutch assembly (base 4A232) is not listed in the catalog, this message does not apply. For vehicle repairs refer to updated Workshop Manual (WSM), Section 205-02 on ATC clutch repairs. Use causal part 4A232 or equivalent and applicable labor operations.
SSM 46495
Service Bulletin/Repair Instructions
SOME 2015-2017 ESCAPE AND MKC VEHICLES WITHOUT A VEHICLE DYNAMIC SUSPENSION SYSTEM AND BUILT ON 1-APR-2015 AND THROUGH 1-OCT-2016 MAY EXHIBIT A RATTLE AND/OR CLUNKING NOISE FROM THE REAR SUSPENSION WHILE DRIVING OVER BUMPS AND/OR MAKING TURNS AT LOW SPEEDS. SUSPECT REAR SHOCK ABSORBERS WILL COMPRESS 2-5 INCHES OF TRAVEL BEFORE SIGNIFICANT RESISTANCE IS OBSERVED. IF WORKSHOP MANUAL (WSM), SECTION 100-04 DIAGNOSTICS INDICATE A RATTLE AND/OR CLUNKING NOISE IS COMING FROM THE REAR SHOCK ABSORBER(S) THEN REFER TO WSM, SECTION 204-02 AND REPLACE THE REAR SHOCK ABSORBER(S)AS REQUIRED. FOR CLAIMING, USE CAUSAL PART 18125 AND APPLICABLE LABOR OPERATIONS IN SECTION 5 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
TSB 17-0034
Service Bulletin/Repair Instructions
SOME 2013-2017 ESCAPE VEHICLES BUILT ON OR BEFORE 28-FEB-2017 MAY EXHIBIT A NOISE AND/OR VIBRATION FROM THE CLIMATE CONTROL BLOWER MOTOR WITH OR WITHOUT A LACK OF AIRFLOW FROM PANEL REGISTERS AND MAY ALSO HAVE AN ODOR. THIS CONCERN MAY BE DUE TO SMALL ANIMALS THAT CAN ENTER THE BLOWER MOTOR HOUSING AREA THROUGH THE AIR INLET DUCT AND CAUSE DAMAGE TO THE AIR INLET DUCT ASSEMBLY AND/OR BLOWER MOTOR ASSEMBLY. THE SMALL ANIMALS MAY DEPOSIT FOREIGN MATERIAL IN THE BLOWER MOTOR ASSEMBLY AND AIR INLET HOUSING THAT MAY CAUSE LACK OF AIRFLOW, NOISE AND/OR VIBRATION. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
TSB 17-0027
Service Bulletin/Repair Instructions
SOME 2015-2017 ESCAPE VEHICLES EQUIPPED WITH EMTC AND BUILT ON OR BEFORE 8-APR-2016 MAY EXHIBIT INCORRECT AIR DISTRIBUTION FROM THE INSTRUMENT PANEL REGISTERS WHEN PANEL MODE IS SELECTED ON THE HEATER VENTILATION AIR CONDITIONING (HVAC) CONTROL PANEL. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 46355
Service Bulletin/Repair Instructions
MULTIPLE 2014-2016 VEHICLES EQUIPPED WITH 6F35 TRANSMISSION AND BUILT ON 1-JAN-2014 AND THROUGH 31-DEC-2015 MAY EXHIBIT HARSH REVERSE ENGAGEMENT AND HARSH/DELAYED 3RD AND 5TH GEAR UP/DOWN SHIFTS WITH NO DTCS PRESENT. THIS MAY BE DUE TO A MECHANICALLY BINDING SHIFT SOLENOID B (SSB). VERIFY HARSH REVERSE AND 3RD AND 5TH GEAR SHIFT EVENTS ARE PRESENT. USING IDS, IDENTIFY THE BAND NUMBER OF SSB FOR USE WHEN ORDERING PARTS. REMOVE THE MAIN CONTROL. DISASSEMBLE AND THOROUGHLY CLEAN THE VALVE BODY AND SOLENOID BODY TO REMOVE ANY CONTAMINANTS. REPLACE SSB, REFER TO WORKSHOP MANUAL (WSM) SECTION 307-01. USING IDS, CLEAR TRANSMISSION ADAPTIVE TABLES. FOR CLAIMING, USE CAUSAL PART 7G383 AND APPLICABLE LABOR OPERATIONS IN SECTION 7 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 46327
Service Bulletin/Repair Instructions
2013-2016 FIESTA, ESCAPE, TRANSIT CONNECT AND 2013 FUSION VEHICLES WITH A 1.6L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI) ENGINE MAY EXHIBIT AN ENGINE OIL LEVEL READING THAT IS UP TO 8 MM ABOVE THE MAXIMUM MARK ON THE ENGINE OIL DIPSTICK WHEN THE ENGINE IS FILLED WITH THE CORRECT AMOUNT OF OIL. THIS IS A NORMAL CHARACTERISTIC OF THIS ENGINE. DO NOT LOWER THE OIL LEVEL TO THE MAXIMUM MARK ON THE ENGINE OIL DIPSTICK IF THE ENGINE CONTAINS THE CORRECT AMOUNT OF OIL. ADDING OIL IS NOT REQUIRED IF THE LEVEL IS ABOVE THE MINIMUM MARK ON THE ENGINE OIL DIPSTICK. REFER TO THE OWNERS MANUAL FOR PROPER ENGINE OIL CAPACITY.
SSM 46295
Service Bulletin/Repair Instructions
TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.
SSM 46281
Service Bulletin/Repair Instructions
SOME 2015-2017 EDGE/MKX, ESCAPE/MKC, FUSION/MKZ AND EXPLORER VEHICLES EQUIPPED WITH A 2.0L OR 2.3L MAY EXHIBIT DAMAGE TO THE ENGINE APPEARANCE COVER, VALVE COVER AND/OR INTAKE MANIFOLD WHEN ATTEMPTING TO REMOVE THE APPEARANCE COVER. TO REDUCE THE POSSIBILITY OF DAMAGE, CAREFULLY PULL STRAIGHT UPWARD ON THE UNDERSIDE OF THE COVER AT EACH FASTENER LOCATION TO REMOVE. DO NOT PULL THE COVER FORWARD OR TO THE SIDE. BEFORE INSTALLING THE ENGINE APPEARANCE COVER, APPLY MOTORCRAFT SILICONE BRAKE CALIPER GREASE AND DIELECTRIC COMPOUND (XG-3-A) TO THE COVER FASTENER GROMMETS. WORKSHOP MANUAL (WSM) INFORMATION IS IN THE PROCESS OF BEING UPDATED
TSB 16-0161
Service Bulletin/Repair Instructions
SOME 2015-2016 ESCAPE VEHICLES EQUIPPED WITH 1.6L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI) ENGINES BUILT ON OR BEFORE 9/30/15 MAY EXHIBIT RUNS ROUGH, LACK OF POWER, SURGE, BUCK/JERK, MISS, LOSS OF RPM, HESITATION AND/OR AN ILLUMINATED MIL WITH DIAGNOSTIC TROUBLE CODE (DTC) P0236 STORED IN THE POWERTRAIN CONTROL MODULE(PCM) MEMORY. THESE CONDITIONS MAY BE CAUSED BY A WIRING CONCERN IN THE REFERENCE VOLTAGE CIRCUIT (VREF) SPLICE. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
TSB 16-0158
Service Bulletin/Repair Instructions
SOME 2015-2017 ESCAPE VEHICLES EQUIPPED WITH EMTC AND BUILT ON OR BEFORE 8-APR-2016 MAY EXHIBIT INCORRECT AIR DISTRIBUTION FROM THE INSTRUMENT PANEL REGISTERS WHEN PANEL MODE IS SELECTED ON THE HEATER VENTILATION AIR CONDITIONING (HVAC) CONTROL PANEL. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 46210
Service Bulletin/Repair Instructions
SOME 2010-2016 EPAS EQUIPPED VEHICLES MAY EXHIBIT STEERING RELATED NOISES. THE WORKSHOP MANUAL (WSM) DIAGNOSTIC PROCEDURES HAVE BEEN UPDATED IN SECTION 211-02. WHEN DIAGNOSING AND REPAIRING EPAS STEERING NOISES USE THE UPDATED PROCEDURES.
SSM 46170
Service Bulletin/Repair Instructions
2013-2017 ESCAPE VEHICLES EQUIPPED WITH MOONROOF EXHIBIT A SMALL VENT OPENING POSITION OF 5 MM. THIS IS THE NORMAL VENT POSITION FOR OPTIMAL NVH/WINDNOISE QUALITIES. WHEN THE VENT IS CLOSED, THE MOONROOF WILL OPEN TO THE 10 MM POSITION THEN CLOSE. THE SLIDING GLASS ALSO OPENS TO THE 10 MM POSITION TO GIVE THE GLASS ENOUGH CLEARANCE BEFORE IT OPENS TO THE REARWARD POSITION. THIS IS THE NORMAL OPERATING CHARACTERISTIC. NO REPAIRS ARE REQUIRED.
SSM 46157
Service Bulletin/Repair Instructions
ALL 2013-2017 ESCAPE VEHICLES EXHIBIT A FRAYED/CUT SHORT APPEARANCE AT THE FRONT EDGE OF THE HEADLINER NEAR THE WINDSHIELD. THIS IS A NORMAL CHARACTERISTIC OF THE HEADLINER AND NO REPAIRS SHOULD BE ATTEMPTED.
SSM 46153
Service Bulletin/Repair Instructions
SETTING THE CORRECT TIRE INFLATION PRESSURE IS AN IMPORTANT STEP IN THE PRE-DELIVERY PROCESS AND DURING ROUTINE MAINTENANCE INTERVALS. RECENT CUSTOMER CLINICS REVEALED THAT MOST EVERY VEHICLE IN THE CLINICS HAD THE TIRE PRESSURES SET INCORRECTLY. TIRE PRESSURES FROM THE FACTORY ARE NOT SET TO THE CORRECT SPECIFICATION. MAINTAINING THE CORRECT TIRE PRESSURE IS KEY TO THE RIDE CHARACTERISTICS OF THE VEHICLE AND AFFECTS RIDE QUALITY, HANDLING, LOAD CAPACITY AND TIRE WEAR. THE RECOMMENDED PRESSURE SETTINGS CAN BE FOUND ON THE TIRE INFORMATION LABEL IN THE DRIVER'S SIDE FRONT DOOR JAM. DO NOT USE THE TIRE PRESSURES LISTED ON THE SIDEWALL OF THE TIRES. MAINTAINING THE TIRE PRESSURE IS PART OF NORMAL MAINTENANCE. IT SHOULD BE RECHECKED MONTHLY, PER THE OWNER GUIDE AND DURING THE RECOMMENDED TIRE ROTATION INTERVALS.
SSM 46132
Service Bulletin/Repair Instructions
SOME 2008-2017 FORD/MERCURY/LINCOLN VEHICLES EQUIPPED WITH SYNC MAY GENERATE A VHR THAT IDENTIFIES A CONCERN WITH THE BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.
SSM 46129
Service Bulletin/Repair Instructions
SOME 2013-2016 FUSION/ESCAPE/MKT/FLEX/MKS/TAURUS, 2015-2016 MKZ/MKC/EDGE AND 2016 MKX VEHICLES MAY EXHIBIT VARIOUS RADIO CONCERNS INCLUDING: SPEAKER STATIC WITH KEY-OFF, NO AUDIO AFTER VEHICLE IS FIRST STARTED WITH DIAGNOSTIC TROUBLE CODE (DTC) U0184, NO VOLUME CONTROL, OR A STUCK CD WITH NO SLOT BLOCKAGE. PRIOR TO STARTING NORMAL DIAGNOSIS FOR ANY OF THESE CONDITIONS, VERIFY THE ACM IS AT THE LATEST CALIBRATION USING IDS VERSION 102.03 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE THE APPLICABLE LABOR OPERATION IN SECTION 11 OF THE SLTS MANUAL AND CAUSAL PART 18C869 WHEN CLAIMING THIS REPAIR.
TSB 16-0139
Service Bulletin/Repair Instructions
SOME 2015-2016 F-150, C-MAX, EDGE, MKS, TAURUS, AND FLEX AND 2016 EXPEDITION, EXPLORER, ESCAPE, FUSION, MUSTANG, MKZ, MKX, NAVIGATOR, TRANSIT AND TRANSIT CONNECT VEHICLES EQUIPPED WITH A 2.0L, 2.5L, 3.5L OR 3.7L GASOLINE ENGINE AND BUILT ON OR BEFORE 31-MAY-2016 MAY EXHIBIT AN INTERMITTENT LOSS OF POWER AND/OR AN ILLUMINATED POWERTRAIN MALFUNCTION (WRENCH) LAMP WITH DIAGNOSTIC TROUBLE CODES (DTCS) P2111, P2112 AND/OR P2119 STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 46102
Service Bulletin/Repair Instructions
Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.
SSM 46085
Service Bulletin/Repair Instructions
The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
TSB 16-2037
Service Bulletin/Repair Instructions
Some 2015-2016 Escape and 2016 Fusion vehicles equipped with a 2.0L GTDI engine may exhibit a rolling reverse to drive engagement shudder on acceleration. Reprogram the powertrain control module (PCM) to the latest calibration using IDS release 102.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
SSM-45838
Service Bulletin/Repair Instructions
INOPERATIVE HANDS-FREE LIFTGATE AFTER ADDITION OF TRAILER HITCH
SSM 46011
Service Bulletin/Repair Instructions
SOME 2015-2017 FOCUS/C-MAX/ESCAPE VEHICLES EQUIPPED WITH ONE TOUCH UP FEATURE. THE 2016-2017 WORKSHOP MANUAL SECTION 501-11 WAS UPDATED 8/2016 WITH REVISED DIAGNOSTICS, THE 2015 WSM UPDATES WILL FOLLOW LATER. REFER TO THE 2016-2017 WSM REVISED DIAGNOSTICS FOR ANY OF THE FOLLOWING CONCERNS: ONE-TOUCH UP FEATURE IS INOPERATIVE, WINDOW DOOR GLASS DOES NOT TRAVEL FULLY TO EITHER OPEN/CLOSED POSITION,AND WINDOW BOUNCES BACK CONCERNS. AT THE BEGINNING OF PINPOINT TEST E, CARRY OUT THE INITIALIZATION PROCEDURE ON THE SUSPECT POWER WINDOW, BEFORE CONTINUING THE PINPOINT TEST. REFER TO: POWER DOOR WINDOW INITIALIZATION - VEHICLES WITH: ONE-TOUCH OPEN AND CLOSE FRONT WINDOWS (501-11 GLASS, FRAMES AND MECHANISMS, GENERAL PROCEDURES).
SSM 45966
Service Bulletin/Repair Instructions
SOME 2015-2016 ESCAPE AND 2016 FUSION VEHICLES WITH THE 2.0L GASOLINE TURBO DIRECT INJECTION (GTDI) ENGINE MAY EXHIBIT A ROLLING REVERSE TO DRIVE ENGAGEMENT SHUDDER ON ACCELERATION WHICH CONTINUES AFTER TSB 15-0187 HAS BEEN COMPLETED. ENGINEERING IS CURRENTLY INVESTIGATING THIS CONDITION. REFER TO WORKSHOP MANUAL (WSM), SECTION 307-01 FOR NORMAL DIAGNOSTICS. TO ASSIST WITH THE INVESTIGATION USE THE REPORT A VEHICLE CONCERN LINK AT THE BOTTOM OF THE OASIS REPORT AND SUBMIT A GLOBAL CONCERN REPORT (GCR). CONTINUE TO MONITOR OASIS FOR UPDATES.
SSM 45926
Service Bulletin/Repair Instructions
2013-2017 FUSION/ESCAPE/MKZ (EXCLUDING 3.7L), 2015-2016 EDGE/EXPLORER (EXCLUDING 3.5L/3.7L), 2015-2016 MKC, AND 2016 MKX VEHICLES (EXCLUDING 3.7L) EQUIPPED WITH ALL WHEEL DRIVE (AWD) MAY EXHIBIT A LEAKING PASSENGER SIDE POWER TRANSFER UNIT (PTU) HALFSHAFT/LINKSHAFT SEAL. THIS MAY BE DUE TO A WORN PTU BUSHING. THE PTU BUSHING CAN NOW BE REPAIRED WITHOUT PTU REPLACEMENT. THE ONLINE WSM IS BEING UPDATED FOR ALL LISTED VEHICLES.REFER TO THE INTERMEDIATE SHAFT BUSHING REMOVAL AND INSTALLATION IN WORKSHOP MANUAL (WSM), SECTION 308-07. THE PROCEDURE IS THE SAME FOR ALL VEHICLES. IF THE PROCEDURE IS NOT PUBLISHED FOR THE VEHICLE BEING SERVICED CHECK THE WSM OF ANOTHER LISTED VEHICLE. BUSHING PART NUMBER IS F2GZ-63600A58A. THE PARTS CATALOG IS BEING UPDATED TO INCLUDE THIS BUSHING.
SSM 45922
Service Bulletin/Repair Instructions
SOME 2013-2016 ESCAPE VEHICLES EQUIPPED WITH 2.5L ENGINE MAY EXHIBIT A ROUGH IDLE, LOW RPM AT IDLE OR A STALL ON HOT RESTART WITH NO DTCS IN SELF TEST. THIS MAY BE DUE TO THE A/C COMPRESSOR CLUTCH BEING SEIZED. IF A VEHICLE COMES IN FOR THIS CONCERN, CHECK THE A/C COMPRESSOR TO SEE IF IT IS ENGAGED DURING START UP/INITIAL RUN. THE PCM STRATEGY KEEPS THE A/C COMPRESSOR CLUTCH OFF FOR 5 SECONDS ON INITIAL START. IF SO, REPLACE THE COMPRESSOR ASSEMBLY (CV6Z-19703-L). IF NOT, PERFORM NORMAL DIAGNOSTICS IN THE PC/ED.
SSM 45887
Service Bulletin/Repair Instructions
2013-2016 ESCAPE,2014-2016 FIESTA, TRANSIT CONNECT AND 2013-2015 FUSION VEHICLES EQUIPPED WITH 1.6L GTDI ENGINE - UPDATED WORKSHOP MANUAL (WSM) SECTION 303-03 COOLING SYSTEM
SSM-45821
Service Bulletin/Repair Instructions
SIRI EYES FREE FUNCTIONAL ISSUES USING BLUETOOTH AND APPLE IOS 9.2 AND 9.2.1
SSM-45810
Service Bulletin/Repair Instructions
A/C COMPRESSOR LOCKUP - VEHICLES IN STORAGE OR USED INFREQUENTLY
SSM-45797
Service Bulletin/Repair Instructions
DRIVE MINIMUM 15 MILES BEFORE DIAGNOSING TIRE VIBRATIONS
16-0066
Service Bulletin/Repair Instructions
Some 2012-2016 vehicles equipped with a touchscreen navigation system and the language set to Arabic may exhibit a blank screen. This may be the result of the ribbon cables not being fully seated inside the front display interface module (FDIM) or an improper software configuration of the FDIM.
TSB160066
Service Bulletin/Repair Instructions
Touchscreen navigation system - arabic language - blank screen
16B10
Service Bulletin/Repair Instructions
In some of the affected vehicles, the front control/display interface module (FCDIM) may have been unintentionally programmed for the European market instead of the North American market
16-0045
Service Bulletin/Repair Instructions
2.0L ECOBOOST - FUEL ODOR ISSUE Some 2013-2016 Escape, 2015-2016 MKC vehicles built on or before 12/15/2015, 2013-2016 Fusion, MKZ, 2013-2015 Explorer, 2013-2014 Focus ST and Edge vehicles equipped with 2.0L EcoBoost engines may exhibit fuel odor originating from the positive crankcase ventilation (PCV) hose. SERVICE PROCEDURE 1. Is the vehicle a 2016 Escape or MKC? a. Yes - check the vehicle build date. Was the vehicle built on or before 12/15/2015? (1) Yes - proceed to Step 2. (2) No - this article does not apply. b. No - proceed to Step 2. 2. Inspect the PCV hose to make sure it is properly connected to the valve cover and the low pressure intake duct. a. For Escape and Focus ST vehicles remove the cowl panel grille to access the hose. Refer to Workshop Manual (WSM), Section 501-02. b. For Edge vehicles remove the air cleaner outlet pipe to access the hose. Refer to WSM, Section 303-12. 3. Does the PCV hose exhibit a fuel smell or was the hose disconnected? a. Yes - replace hose and reassemble the vehicle. b. No - Refer to WSM, Section 303-13 for normal diagnosis.
TSB160045
Service Bulletin/Repair Instructions
2.0L Ecoboost - Fuel odor
16-0033
Service Bulletin/Repair Instructions
WIND OR WHISTLE NOISE FROM EXTERIOR MIRROR(S) AT HIGHWAY SPEED - BUILT ON OR BEFORE 1/22/2016 ISSUE Some 2013-2016 Escape vehicles built on or before 1/22/2016 may exhibit a wind or whistle noise from the exterior mirror(s) at highway speed.
LTR3756
Service Bulletin/Repair Instructions
49 CFR Part 579.5 Monthly Communications - January 2016
TSB160001
Service Bulletin/Repair Instructions
49 CFR Part 579.5 Monthly Communications - March 2016 Air bag warning light illuminated with diagnostic trouble code (DTC) B141B and/or B141C
TSB160033
Service Bulletin/Repair Instructions
Wind or whistle noise from exterior mirror(s) at highway speed - buklt on or before 01/22/2016
15-0162
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB45300
Service Bulletin/Repair Instructions
FORD ESCAPE: CLEANING TIP FOR CHROME APPEARANCE PHYSICAL VAPOR DISPOSITION. USE OF CERTAIN OFF-THE-SHELF CLEANER/OR POLISHING PRODUCTS MAY CAUSE HARM TO WHEELS *CN
TSB150162
Service Bulletin/Repair Instructions
1.6L GTDI - Lack of power with MIL Illuminated - DTCS P0234, P0245, P0246 And/Or P0299. Some 2013-2016 Escape 2014-2016 Fiesta ST, and 2013-2014 Fusion vehicles equipped with a 1.6L Gasoline Turbocharged Direct Injection (GTDI) engine may exhibit a lack of power concern with malfunction indicator lamp (MIL) illuminated and diagnostic trouble codes (DTCs) P0234, P0245, P0246 and/or P0299 stored in powertrain control module (PCM) MEMORY.
SB45261
Service Bulletin/Repair Instructions
FORD: WHEN ATTEMPTING TO EJECT COMPACT DISC (CD) FROM PLAYER THE CD GETS STUCK. MISALIGNMENT OF PLAYER TO INSTRUMENT PANEL MAY BE POSSIBLE CAUSE *CN
TSB15-0130
Service Bulletin/Repair Instructions
FORD: 2013-2016 ESCAPE VEHICLES WILL HAVE A WHISTLING OR WIND TYPE NOISE FROM EXTERIOR MIRRORS, AT HIGHWAY SPEED *CN
TSB15-0129
Service Bulletin/Repair Instructions
FORD: 2013-2015 C-MAX AND 2013-2016 ESCAPE EQUIPPED WITH LEATHER SEATING MAY EXPERIENCE CRACKS IN DRIVER FRONT OR PASSENGER SIDE FACING PANEL OR SEAT CUSHION COVER OUTBOARD BOLSTER *CN
45259
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-45308
Service Bulletin/Repair Instructions
2015-2015 FORD ESCAPE: DUE TO CLUSTER RESET VEHICLE MAY EXHIBIT INTERMITTENT BATTERY DRAW WHICH CAN RESULT IN A DEAD BATTERY OR NO START *CN
SB-45313
Service Bulletin/Repair Instructions
2015 FORD ESCAPE: INOPERATIVE DIGITAL SPEEDOMETER OR MISSING DIGITAL SPEEDOMETER AFTER REPROGRAMMING *CN
SB45295
Service Bulletin/Repair Instructions
FORD ESCAPE: RIGHT OR LEFT SIDE CATCH/STRIKER ASSEMBLY COMING LOOSE, CAUSE GLOVEBOX DOOR TO BE MISALIGNED *CN
SB45268
Service Bulletin/Repair Instructions
FORD: SOME ESCAPE VEHICLES MAY EXPERIENCE A DEAD BATTERY OR A NO START CONDITION DUE TO A POSSIBLE CLUSTER RESET *CN
44863
Service Bulletin/Repair Instructions
FORD: NO SERVICE ACTION IS RECOMMENDED FOR THIS CONDITION. PLEASE USE AT YOUR DISCRETION. VARIOUS 2010-2015 VEHICLES MAY EXPERIENCE A TURBULENCE NOISE, SIMILAR TO AN HELICOPTER NOISE, AT HIGHWAY SPEEDS WHEN THE REAR DOOR WINDOW(S) OR SUNROOF ARE OPEN. *TA
ASI-45225
Service Bulletin/Repair Instructions
LINCOLN/FORD: SOME VEHICLES WILL EXPERIENCE TIRE VIBRATION AND POSSIBLE FLAT SPOTTING. VEHICLE NEEDS TO BE CHECKED AND DRIVEN, BY WORKSHOP TECH, APPROXIMATELY 15 MILES FOR DIAGNOSIS OF VIBRATIONS AND FLAT SPOTTING. MODEL 2013-16 ESCAPE, 2015-16 MKC. *PE
ASI-45239
Service Bulletin/Repair Instructions
FORD: SOME VEHICLES TRANSMISSION WILL EXPERIENCE, AFTER A COLD SOAK OR AN EXTENDED PERIOD WITH ENGINE OFF, A 2-3 SHIFT HESITATION DUE TO POSSIBLE HYDRAULIC CIRCUIT DRAIN. MODEL 2013-16 VARIOUS VEHICLES. *PE
ASI-45156
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ASI-45165
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ASI-45166
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ASI-45183
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
15-0070
Service Bulletin/Repair Instructions
FORD 2013-2015 ESCAPE: BULLETIN INFORMATION INVOLVING VEHICLES EQUIPPED WITH 1.6L GASOLINE TURBOCHARGED DIRECT INJECTED ENGINE BUILT BEFORE 3/13/2015 MAY EXPERIENCE AN ENGINE IDLE SURGE AT ON COLD START, REPROGRAMMING THE PCM MAY CORRECT THE ISSUE. *LJ
44855
Service Bulletin/Repair Instructions
FORD: SOME 2013-2015 FORD C-MAX, 2013-2015 FORD ESCAPE, AND 2012-2014 FORD FOCUS EQUIPPED WITH MY FORD TOUCH MAY BE EXPERIENCING COMPACT DISCS GETTING STUCK WHILE ATTEMPTING TO EJECT OUT THE SYSTEM. *TA
ASI-44707
Service Bulletin/Repair Instructions
FORD: AFTER POWERTRAIN CONTROL MODULE REPROGRAMMING, THE MALFUNCTION INDICATOR LAMP (MIL) IS ON WITH SEVERAL DIAGNOSTIC TROUBLE CODES (DTC) P06B8, P068A, P2610, IF KEY NOT LEFT FOR 30 SECONDS IN OFF POSITION FOLLOWING PROGRAMMING ON SOME MODEL 2009-15 VEHICLES. *PE
ASI-44725
Service Bulletin/Repair Instructions
FORD/LINCOLN: VEHICLE IS EXHIBITING VIBRATIONS WHILE DRIVING AND CAUSE IS BEING ATTRIBUTED TO TIRES AND PROCEDURE IS DRIVE APPROXIMATE 15 MILES TO ELIMINATE ANY FLAT CONDITION AND MISDIAGNOSIS. MODEL 2013-15 ESCAPE, 2015 MKC. *PE
ASI-44726
Service Bulletin/Repair Instructions
FORD: CLOCK FAILS TO BE SET UNLESS FRONT CONTROL DISPLAY INTERFACE MODULE FCDIM) HAS DATE SET FIRST AND THEN TIME. MODEL 2013-2015 C-MAX, 2014-2015 ESCAPE, 2014 FOCUS. *PE
ASI-44649
Service Bulletin/Repair Instructions
FORD: A JOB AID WAS DEVELOPED AND NOW AVAILABLE FOR THE PTU INTERNAL OR EXTERNAL FLUID LEAKAGE FOR ALL WHEEL DRIVE VEHICLES. *PE