Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 54601
Service Bulletin/Repair Instructions
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
TSB 25-2570
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.
SSM 54366
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
SSM 53040
Service Bulletin/Repair Instructions
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
TSB 24-2165
Service Bulletin/Repair Instructions
This article supersedes TSB 21-2175 to update the TSB Service Procedure. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.
SSM 52476
Service Bulletin/Repair Instructions
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
SSM 52410
Service Bulletin/Repair Instructions
Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
SSM 52335
Service Bulletin/Repair Instructions
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 51838
Service Bulletin/Repair Instructions
In various 2017-2023 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.
SAN-Vol1 I1
Service Bulletin/Repair Instructions
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
SSM 51536
Service Bulletin/Repair Instructions
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
SSM 51409
Service Bulletin/Repair Instructions
Some 2014-2020 Fusion and 2017-2019 Escape vehicles may be equipped with a 1.5L Ecoboost engine that uses a 50-tooth variable camshaft timing (VCT) intake and exhaust unit from the assembly plant or if a service long block was installed. VCT locking tool 303-1097 is not compatible with this system. If VCT system service is required, replace both the intake VCT (service part DS7Z-6256-F) and exhaust VCT (service part DS7Z-6256-G) as a pair. An interim loaner tool program has been established to enable these repairs. Contact 1-800-403-4844 (Monday-Friday 8:00am to 8:00pm EST; Saturday 8:00am to 3:00pm EST) to obtain this tool. A VCT locking tool compatible with the 50-tooth system is under development and will be sent to dealerships. Continue to monitor OASIS for additional information.
SSM 51261
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 51120
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
TSB 22-2322
Service Bulletin/Repair Instructions
Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
SSM 50975
Service Bulletin/Repair Instructions
Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPassÃÂÃÂÃÂî/LincolnWayÃÂÃÂÃÂî app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
SSM 50873
Service Bulletin/Repair Instructions
Some 2017-2022 Ford and Lincoln vehicle owners may experience a condition of missing authorization, command and control, battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.
TSB 22-2229
Service Bulletin/Repair Instructions
Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure to replace the long block engine assembly.
19B37
Service Bulletin/Repair Instructions
Certain 2017-2019 Model Year Fusion and Escape Vehicles Equipped with a 1.5L GTDI Engine - Powertrain Control Module Programming - Some of the affected vehicles may exhibit collant intrusion into the cylinder bores. Customer symptoms include coolant loss, excessive tailpipe smoke, or illuminated malfunction indicator lights (MIL) due to engine misfire. Over time, this condition may damage the engine, requiring replacement of the short block.
19B37-S4
Service Bulletin/Repair Instructions
Certain 2017-2019 Model Year Fusion and Escape Vehicles Equipped with a 1.5L GTDI Engine - Powertrain Control Module Reprogramming. Some of the affected vehicles may exhibit coolant intrusion into the cylinder bores. Customer symptoms include coolant loss, excessive tailpipe smoke, or illuminated malfunction indicator lights (MIL) due to engine misfire. Over time, this condition may damage the engine, requiring replacement of the engine short block.
21N12
Service Bulletin/Repair Instructions
Certain 2017-2019 Model Year Fusion and Escape Vehicles Equipped with a 1.5L GTDI Engine â Short Block Replacement After Coolant Intrusion. In some of the affected vehicles the 1.5L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or may run in a rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into a cylinder bore.
SSM 50804
Service Bulletin/Repair Instructions
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
SSM 50726
Service Bulletin/Repair Instructions
Some 2017-2021 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 22-2066
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
TSB 22-2133
Service Bulletin/Repair Instructions
Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
TSB 22-2134
Service Bulletin/Repair Instructions
Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
SSM 50651
Service Bulletin/Repair Instructions
In various 2017-2022 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating "Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option
TSB 22-2104
Service Bulletin/Repair Instructions
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 50502
Service Bulletin/Repair Instructions
Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
SSM 50439
Service Bulletin/Repair Instructions
Some 2017-2020 Fusion/MKZ and 2017-2019 Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may require replacement of the long block engine assembly. New service kits have been released which include all the one-time-use components required in the service procedure for removal and replacement of the long block engine assembly. Refer to the Ford Electronic Parts Catalog (ECAT) for long block service kit part number by application.
SSM 50375
Service Bulletin/Repair Instructions
Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
SSM 50346
Service Bulletin/Repair Instructions
Some 2018-2021 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 50251
Service Bulletin/Repair Instructions
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-2269
Service Bulletin/Repair Instructions
Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
SSM 50067
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 50064
Service Bulletin/Repair Instructions
Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 50049
Service Bulletin/Repair Instructions
Some 2017-2021 Ford and Lincoln vehicle customers may receive a message in their FordPass or Lincoln Way App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.
SSM 50039
Service Bulletin/Repair Instructions
Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
TSB 21-2236
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 49924
Service Bulletin/Repair Instructions
Some 2019 MKC, 2019-2021 Edge/Nautilus/Escape/Ranger/Explorer, 2020-2021 Corsair, and 2021 Bronco Sport vehicles equipped with 2.0L and 2.3L EcoBoost engines may exhibit a light to moderate ticking type noise at idle (600-700 RPM). The noise is usually more prominent in the area of the high-pressure fuel pump, located on the top of the engine just behind the number 4 ignition coil. This noise is not detrimental to engine function and has no short or long-term effects on engine durability. This an operating characteristic of these engines and no repairs should be attempted.
SSM 49885
Service Bulletin/Repair Instructions
Some 2019-2021 Ford and Lincoln vehicles may exhibit an intermittent audio echo/robotic voice heard during a bluetooth phone call by the person that is not in the vehicle. Using Apple CarPlay and Android Auto instead of Bluetooth can help alleviate the concern. Also turning on, then off, the privacy setting in the SYNC touchscreen can temporarily alleviate the concern. Engineering is currently investigating this concern and will be releasing a service fix in early July 2021. Let the customer know they can continue to drive the vehicle and schedule service appointments for customers once the repair becomes available. Monitor OASIS for updates.
TSB 21-2175
Service Bulletin/Repair Instructions
Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.
SSM 49820
Service Bulletin/Repair Instructions
Some 2017-2021 Ford and Lincoln vehicle owners may experience a condition of missing Authorization, Command and Control, Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.
SSM 49821
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49803
Service Bulletin/Repair Instructions
Some 2018-2020 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-2152
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
SSM 49795
Service Bulletin/Repair Instructions
Some 2018-2021 Ford and Lincoln vehicles may not be able to perform remote commands via the FordPass/LincolnWay App due to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
TSB 21-2077
Service Bulletin/Repair Instructions
Some 2017-2019 Escape/MKC Some 2017-2019 Escape/MKC vehicles equipped with all-wheel drive (AWD) may exhibit a binding/shudder and/or bump/clunk from the rear drive unit (RDU) when turning at low speeds and parking lot maneuvers. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM. T
TSB 21-2033
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2013-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and install the protective cap over the selector at the transmission end of the selector lever cable.
SSM 49596
Service Bulletin/Repair Instructions
Some 2017-2019 Escape/Fusion vehicles may exhibit a rolling idle after an engine repair that required the crankshaft pulley removal, or a drive belt component failure. The crankshaft pulley to be slightly out of alignment in relation to engine top dead center (TDC) causing an incorrect crankshaft position (CKP) sensor signal. To determine this as the cause of the rolling idle, position the crankshaft at TDC using essential special service tool (ESST) 303-748 then remove the CKP Sensor and attempt to install ESST 303-1550. If the bolt to hold 303-1550 cannot be installed by hand, this indicates that the crank pulley is not properly installed. Using a new crank bolt, install the pulley/vibration damper in its proper alignment following the WSM procedure in 303-01. Use ESST 303-393A to hold the flexplate/crankshaft when torqueing down the crank bolt.
SSM 49541
Service Bulletin/Repair Instructions
Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code on the PTS website (Detailed Vehicle Specifications). If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early March. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early March. Monitor OASIS for updates.
SSM 49328
Service Bulletin/Repair Instructions
Some 2019 MKC, 2019-2020 Edge/Nautilus/Escape/Ranger, 2020 Corsair, 2019-2021 Explorer vehicles equipped with 2.0L and 2.3L EcoBoost engines may exhibit a light to moderate ticking type noise at idle (600-700 RPM). The noise is usually more prominent in the area of the high-pressure fuel pump, located on the top of the engine just behind the number 4 ignition coil. This noise is not detrimental to engine function and has no short or long-term effects on engine durability. This an operating characteristic of these engines and no repairs should be attempted.
SSM 49292
Service Bulletin/Repair Instructions
Some 2018-2020 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14H092 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49284
Service Bulletin/Repair Instructions
Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
SSM 49210
Service Bulletin/Repair Instructions
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
SSM 49084
Service Bulletin/Repair Instructions
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 20-2255
Service Bulletin/Repair Instructions
Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
SSM 48908
Service Bulletin/Repair Instructions
Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
SSM 48895
Service Bulletin/Repair Instructions
Some 2017-2019 Escape vehicles equipped with a 1.5L or 2.0L engine may exhibit fuse F34 open with an illuminated MIL and diagnostic trouble codes (DTCs) P0034, P023A, P0245, P0480, P0481, P0645, P06A0, P06DB, P188D, P02602, and/or P2681 in the powertrain control module (PCM). The vehicle may also exhibit an all-wheel drive (AWD) fault warning and/or illuminated traction control (TC) lamp. Inspect the 12A690 (1.5L) or 12C508 (2.0L) wiring harness from the battery junction box (BJB) to the PCM for wiring harness retainers not installed correctly allowing chafing to occur at multiple points. Repair damaged wiring as required. Refer to the Wiring Diagram for repair information. For claiming, use causal part 12A690 (1.5L) or 12C508 (2.0L) and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 48858
Service Bulletin/Repair Instructions
Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
TSB 20-2171
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
TSB 20-2165
Service Bulletin/Repair Instructions
Some 2017-2019 Escape vehicles equipped with a 1.5L EcoBoost engine and all-wheel drive (AWD) may exhibit a bump or clunk from the rear drive unit (RDU) when turning at low speeds and parking lot maneuvers. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.
19B37-S3
Service Bulletin/Repair Instructions
Some of the affected vehicles may exhibit coolant intrusion into the cylinder bores. Customer symptoms include coolant loss, excessive tailpipe smoke, or illuminated malfunction indicator lights (MIL) due to engine misfire. Over time, this condition may damage the engine, requiring replacement of the engine short block.
SSM 48757
Service Bulletin/Repair Instructions
Some customers may experience a notification in the FordPass and/or LincolnWay apps that indicates their vehicle has entered "deep sleep mode". This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".
SSM 48725
Service Bulletin/Repair Instructions
2016-2019 Escape vehicles equipped with the 1.6L EcoBoost or 1.5L EcoBoost engines may have missing or damaged dowel alignment pins between the engine and transaxle. When either a new long block or new short block is installed in the vehicle and the dowel pins were found missing or damaged upon disassembly of the original engine, the flexplate (6375) must be replaced. For engine overhauls or other engine related repairs where the engine and transaxle do not require separation, replacing the flexplate is not required. This direction also applies to existing service publication repairs where the engine and transaxle are separated as part of the repair procedure. Refer to Workshop Manual (WSM), Section 303-01.
TSB 20-2100
Service Bulletin/Repair Instructions
Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
SSM 48619
Service Bulletin/Repair Instructions
SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
19B37-S2
Service Bulletin/Repair Instructions
Attachments: A new Service Advisor to Customer interaction video is now available. This video illustrates the speed and simplicity of the dongle re-flash process. ⢠Non-Traditional Repair Approaches: The dongle re-flash process allows for an improved customer experience, dealer service efficiency, speed, and no need for an appointment, service bay, or trained technician. ⢠Service Action: All dealers will be shipped at least one dongle by February 28, 2020. ⢠Shipment of dongles began the week of February 17, 2020. Dealers with the largest VIN count received the initial shipment. ⢠Dealers may request additional dongles from the SSSC as needed. ⢠Technician time clocking is not required for this program when using the 19B37 dongle.
SSM 48558
Service Bulletin/Repair Instructions
SSM 48558 - 2017-2020 Various Vehicles Equipped With Telematics Control Unit (TCU) - Various FordPass/LincolnWay Mobile App Concerns Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
19B37-S1
Service Bulletin/Repair Instructions
Some of the affected vehicles may exhibit coolant intrusion into the cylinder bores. Customer symptoms include coolant loss, excessive tailpipe smoke, or illuminated malfunction indicator lights (MIL) due to engine misfire. Over time, this condition my damage the engine, requiring replacement of the engine short block.
TSB-20-2002
Service Bulletin/Repair Instructions
Some 2018-2019 Escape vehicles equipped with a 1.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P051B stored in the powertrain control module (PCM). This may be due to the crankcase pressure sensor. To correct the condition, follow the Service Procedure steps to replace the crankcase pressure sensor.
SSM 48423
Service Bulletin/Repair Instructions
Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 19-2346
Service Bulletin/Repair Instructions
Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
TSB 19-2375
Service Bulletin/Repair Instructions
This article supersedes TSB 19-2139 to update the production fix date. Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, replace the short block and head gasket.
SSM 48345
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/Escape/Nautilus/Corsair vehicles equipped with 2.0L EcoBoost engines may exhibit low coolant, white smoke from the tailpipe, an over temperature warning in the instrument panel cluster (IPC), external coolant leaking, and/or illuminated MIL with DTCs P0217, P0401, P1026, P1285, P1299, P2196 or P2467 stored in the PCM. This may be due to an EGR Cooler that is leaking coolant into the engine intake and exhaust system. The EGR cooler should be inspected first to detect the presence of any internal leaks by a visual inspection and a pressure test as defined in the Workshop Manual (WSM). If any coolant is found leaking from the coolant chamber into the exhaust chamber, replace the EGR cooler. If no issues are detected with the EGR cooler, continue repair diagnosis using standard diagnostic procedures as defined in the WSM.
SSM 48340
Service Bulletin/Repair Instructions
Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.
TSB 19-2139
Service Bulletin/Repair Instructions
Some 2014-2019 Fusion vehicles built on or before 21-Feb-2019 and 2017-2019 Escape vehicles built on or before 06-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, replace the short block and head gasket.
SSM 48335
Service Bulletin/Repair Instructions
Some 2017-2019 Escape vehicles may exhibit a 'Trailer Connected' or 'Trailer Disconnected' message in the vehicle's message center with no trailer attached to the vehicle. To correct this condition, reprogram the trailer module (TRM) using the appropriate Ford diagnostic scan tool. For claiming use causal part (19H332) and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 48316
Service Bulletin/Repair Instructions
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
SSM 48279
Service Bulletin/Repair Instructions
Some 2018-2019 Ford and Lincoln vehicles equipped with a telematics control unit (TCU) may exhibit a persistent message in the Ford Pass/Lincoln Way mobile app advising, Your vehicles software is being updated. Vehicle controls will be unavailable for about 10 minutes while this update takes place. This may be due to the TCU still in factory mode. Using the appropriate Ford diagnostic scan tool, check the TCU_AUTHSTATE PID status showing Factory Mode. To correct this condition, perform programmable module installation (PMI) on the telematics control unit (TCU). Once PMI is completed, ensure the TCU_AUTHSTATE PID in service tool no longer displays Factory Mode. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM) section 415-00. For claiming, use causal part 14G229.
SSM 48267
Service Bulletin/Repair Instructions
Some 2018-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
SSM 48260
Service Bulletin/Repair Instructions
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
TSB 19-2265
Service Bulletin/Repair Instructions
Some 2019 Escape and MKC vehicles built on 15-Feb-2019 and through 12-Mar-2019 may exhibit a whistle noise from the heating ventilation and air conditioning (HVAC) evaporator core cover area where the evaporator tubes enter the evaporator case in the passenger footwell area. The noise will be most noticeable while transitioning into maximum heat with higher blower speeds. This may be due to incorrect evaporator core cover to evaporator case sealing that can allow an air leak and result in a whistle noise. To correct the condition, follow the Service Procedure steps to apply a small piece of mastic sealing patch to the evaporator case/cover joint.
SSM 48150
Service Bulletin/Repair Instructions
Some 2014-2019 Fusion and 2017-2019 Escape with 1.5L engine may exhibit coolant usage and white smoke from exhaust. Follow Cooling System Pressure Test process in WSM, Section 303-03. Pressurize system to 138kPa(20 psi) and hold 5 hours. If system pressure drops 27.57kPa(4psi) after 5 hours and borescope inspection through spark plug holes shows coolant presence in bores, the short block must be replaced. Further teardown inspection is not required, nor is completing cost cap. Cost cap requirements are waived for repairs completed utilizing this SSM. Reuse the original cylinder head for the repair. Ford has found all returned 1.5L cylinder heads pass inspection and replacement was not required. Follow WSM, Section 303-01A for repair procedure and refer the parts catalog as needed. Any backorders experienced will be filled as quickly as possible.
SSM 48135
Service Bulletin/Repair Instructions
Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 48130
Service Bulletin/Repair Instructions
Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
SSM 48123
Service Bulletin/Repair Instructions
For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
SSM 48106
Service Bulletin/Repair Instructions
Some 2014-2019 Fusion and 2017-2019 Escape vehicles with 1.5L Ecoboost engine exhibiting coolant consumption and white smoke from the exhaust. Follow Cooling System Pressure Test procedure in WSM, Section 303-03, and pressurize system to 138kPa(20 psi) and hold for 5 hours. If system pressure drops 27.57kPa (4psi) after 5 hours and borescope inspection through spark plug holes confirms coolant intrusion into the cylinders, short block replacement is required. Further teardown inspection is not required. Reuse the original cylinder head for the repair. Ford has found all returned 1.5L cylinder heads pass inspection and replacement was not required. Follow WSM, Section 303-01A procedures for repairs and refer the parts catalog as needed. Short block availability may be limited and temporary backorders will be filled as quickly as possible.
TSB 19-2208
Service Bulletin/Repair Instructions
Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
SSM 48053
Service Bulletin/Repair Instructions
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section
SSM 48046
Service Bulletin/Repair Instructions
Some 2018-2019 Escape vehicles built on 01-Aug-2018 and through 14-May-2019 or 2019 MKC vehicles built on or before 14-May-2019 equipped with a 2.0L engine may exhibit an auto start/stop, no auto restart concern with diagnostic trouble code (DTC) P164C. A revised crankshaft position sensor (CKP) JX6Z-6C315-B is available. Refer to the Workshop Manual (WSM), Section 303-14A. For claiming, use causal part 6C315 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 19-2172
Service Bulletin/Repair Instructions
Some 2015-2018 Edge and 2015-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
SSM 48015
Service Bulletin/Repair Instructions
Some 2019 Escape/Fusion vehicles equipped with a Sony branded audio system may exhibit AM presets that may not save and/or may be lost after an ignition cycle. To address this condition, reprogram the audio control module (ACM) using the appropriate Ford diagnostic scan tool. For claiming use causal part 18C869 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.
TSB19-2171
Service Bulletin/Repair Instructions
Some 2017-2019 Escape/MKC vehicles equipped with a 1.5, 2.0L or 2.3L EcoBoost engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04F0 and/or P144C stored in the powertrain control module (PCM). This may be due to loose or partially connected evaporative emissions (EVAP) vapor lines. Before completing the Powertrain Control/Emissions Diagnosis (PC/ED) Manual pinpoint test (PPT) follow the Service Procedure steps on vehicle.
SSM 47976
Service Bulletin/Repair Instructions
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 47850
Service Bulletin/Repair Instructions
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 47948
Service Bulletin/Repair Instructions
SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 47937
Service Bulletin/Repair Instructions
SSM 47937 - 2019 MKC, 2018-2019 Escape - 2.0L - Auto Start/Stop - No Auto Restart After An Auto Stop Event With DTC P164C Some 2018-2019 Escape vehicles built on or after 01-Aug-2018 or 2019 MKC vehicles equipped with a 2.0L engine may exhibit an auto start/stop, no auto restart concern with diagnostic trouble code (DTC) P164C. A revised crankshaft position sensor (CKP) JX6Z-6C315-B is available. Refer to the Workshop Manual (WSM), Section 303-14A. For claiming, use causal part 6C315 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 47909
Service Bulletin/Repair Instructions
SSM 47909 - 2017-2019 Escape, MKC - License Plate Bracket Nut(s) Damaged With Over Torqued Screw(s) 2017-2019 Escape and MKC vehicles may exhibit a concern of the license plate bracket nut(s) being damaged due to the screw(s) being over torqued. The torque specification for these screws are 1.7 Nm (1.25 lb-ft). Engineering recommends not to use any power tool to tighten these screws. Most any power tool will apply more torque to the screws than the allowed torque specification and will damage the plastic nut(s).
SSM 47875
Service Bulletin/Repair Instructions
Some 2014-2019 Escape, 2014-2018 C-MAX, Focus, and Transit Connect vehicles not equipped with an auto start/stop system may exhibit an inability to program and/or no electrical power after installation of a service part body control module (BCM). Inspect the BCM for the presence of fuse F88. If fuse 88 is missing, install a 25 amp fuse and then re-evaluate the concern. If fuse 88 is installed in a vehicle with an auto start/stop system, the vehicle may exhibit concerns where the radio is turning off during an auto start/stop event and the instrument panel cluster (IPC) back lighting slowly goes dim during auto start/stop events.
SSM 47849
Service Bulletin/Repair Instructions
Some 2014-2019 Fusion and 2017-2019 Escape equipped with 1.5L Ecoboost engine may exhibit coolant consumption and white smoke concern. Follow the Cooling System Pressure Test procedure in WSM, Section 303-03, pressurize the cooling system to 138kPa(20 psi0 and hold for 5 hours. If cooling system pressure drops 27.57kPa(4psi) after 5 hours and internal engine coolant loss is confirmed, further investigation of the engine block surface to head gasket interface is required. Carefully inspect engine block cylinders and cylinder bore bridges for erosion, pitting, and flatness. If defects with the cylinder block surface are identified, follow WSM, Section 303-01A procedures for repairs. Complete cost cap as needed to determine the most cost effective repair. Ford has found that all returned cylinder heads pass inspection and may have been reused.
TSB 19-2056
Service Bulletin/Repair Instructions
Some 2017-2019 Escape vehicles may exhibit a power liftgate that bounces back and/or will not cinch to the fully closed position. This may be due to the adjustment of the striker, latch, liftgate margins, flushness and/or striker wings. To resolve the condition, adjust the striker position or the striker wings.
SSM 47824
Service Bulletin/Repair Instructions
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 47821
Service Bulletin/Repair Instructions
Some 2018-2019 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
19B02
Service Bulletin/Repair Instructions
Certain 2019 Model Year Escape Vehicles Equipped With R1234yf Refrigerant - Special Air Conditioning - Evacuation and Charging Service Information
SSM 47784
Service Bulletin/Repair Instructions
Some 2017-2019 Escape vehicles built on or after 6-Apr-2017 equipped with factory trailer tow may exhibit a concern with a trailer lamp out warning and/or blind spot information system (BLIS) not available warning without a trailer connected to the vehicle. Access connectors C439 (4 pin) and C432 (12 pin) within the trailer connector harness (15K868). Refer to Wiring Diagram, Cell 151. Inspect connectors for corrosion and/or water contamination. Clean as required and add electrical grease (XG-12 or equivalent). Make certain the protective cover over C439 is installed and fully seated to prevent future water intrusion. For claiming, use causal part 15K868 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 47771
Service Bulletin/Repair Instructions
Some 2019 Escape/Fusion vehicles equipped with a Sony branded audio system may exhibit AM presets that may not save and/or may be lost after an ignition cycle. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.
SSM 47748
Service Bulletin/Repair Instructions
Some 2016-2019 Escape and 2016-2018 Focus/C-Max vehicles may exhibit a customer perceived concern of a FDIM screen flicker during transitions between day/night mode and/or during auto headlamp on/off. The FDIM utilizes a ramp up and ramp down strategy of controlling the back lighting when the display setting is in auto dimming mode. This is a normal condition that does not affect the function or durability of the FDIM. Auto dimming mode can be turned off to minimize the ramp up and ramp down lighting strategy. To turn off the auto dimming mode feature in the FDIM display: select> FDIM settings> Display settings> Auto Dim selection. Do not confuse the auto dimming mode selection with the selection for auto day/night operation. Turning off auto dimming mode only effects the back lighting strategy and does not affect any other function or FDIM reliability.
SSM 47749
Service Bulletin/Repair Instructions
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
SSM 47750
Service Bulletin/Repair Instructions
Some 2018-2019 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
SSM 47735
Service Bulletin/Repair Instructions
Some 2018-2019 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition, remove the TCU fuse for 5 minutes prior to programing. Delete all previous session files for the vehicle and do not install the TCU fuse until a new IDS session has been started. Once the new session has been started and the fuse reinstalled, the TCU can be programmed. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
SSM 47722
Service Bulletin/Repair Instructions
Some 2018-2019 Escape, Transit Connect and EcoSport vehicles equipped with a keyed ignition and a factory invoiced accessory (FIA) VSS may exhibit intermittent alarm activation with lights flashing and the horn sounding after a loud noise and/or shockwave near the vehicle (ex. large truck passing, garage door slamming closed). The root cause of this concern may be an incorrect shock sensor sensitivity adjustment on the VSS module. Perform the shock sensor sensitivity adjustment procedure outlined in the vehicle security/remote start installation guide located on the PTS website. The shock sensor requires adjustment during the installation of a vehicle security/remote start system. The shock sensor sensitivity adjustment procedure should be performed following the installation instructions.
SSM 47724
Service Bulletin/Repair Instructions
Some 2018-2019 Escape vehicles equipped with Sirius satellite radio with a 4G telematics control unit (TCU) built on or before 31-Oct-2018 may exhibit an intermittent loss of satellite radio reception while displaying an acquiring signal message when driving in unobstructed areas. If this condition is present, use OASIS to verify the vehicle is equipped with a 4G TCU modem. Replace the audio unit antenna with GM5Z-18936-GF. Refer to Workshop Manual (WSM), Section 415-00. For claiming, use causal part 18936 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.
SSM 47711
Service Bulletin/Repair Instructions
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
SSM 47704
Service Bulletin/Repair Instructions
Some 2017-2019 Escape vehicles equipped with a 1.5L EcoBoost engine may exhibit a timing belt saw or chirp type noise at idle while the vehicle is in transport mode. The noise is noticeable because of an elevated idle speed while the vehicle is in transport mode. Do not disable transport mode to diagnose or perform a repair for this noise. Transport mode should only be disabled as directed by the pre-delivery procedure.
SSM 47703
Service Bulletin/Repair Instructions
Some 2014-2019 Escape, 2014-2018 C-MAX,Focus, and Transit Connect vehicles may exhibit a concern of not able to program and/or no electrical power after installation of a service part Body Control Module(BCM). Inspect the BCM for the presence of fuse F88. If the fuse is missing, install the correct size replacement fuse as outlined in the Wiring Manual and then re-evaluate the concern.
TSB 18-2361
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
SSM 47678
Service Bulletin/Repair Instructions
2013-2019 Escape and 2015-2019 MKC vehicles equipped with a power roof opening panel will exhibit a small vent opening position of 5 mm (.197 in). This is the normal vent position for optimal noise, vibration, harshness (NVH) and windnoise qualities. When the vent is closed, the front sliding glass panel will open to the 10 mm (.394 in) position and then close. The front sliding glass panel also opens to the 10 mm (.394 in) position to give the front sliding glass panel enough clearance before it opens to the rearward position. This is a normal operating characteristic of the front sliding glass panel. No repairs are required.
SSM 47662
Service Bulletin/Repair Instructions
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 47634
Service Bulletin/Repair Instructions
Some 2013-2019 Escape and 2015-2019 MKC vehicles may exhibit a vibration attributed to the tires. Prior to performing any road force balancing procedures or related diagnosis, make sure the vehicle tire pressure is correct and is driven a minimum of 24 Km (15 miles) to eliminate any possible flat spotting conditions and potential misdiagnosis. Refer to Workshop Manual (WSM), Section 204-04A for further information. In addition, it is recommended that diagnosis of tire/wheel vibration should not be performed on tires with less than 320 Km (200 miles). Some initial tire/wheel vibration issues (such as flat spotting) may correct themselves after the tires have been in service for 320 Km (200 miles). Setting tire pressure to the correct placard pressure is contained within pre-delivery inspection.
SSM 47638
Service Bulletin/Repair Instructions
2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
TSB 18-2331
Service Bulletin/Repair Instructions
Some 2017-2019 Escape vehicles may exhibit a vibration at highway speeds above 80 Km/h (50 MPH) which may be attributed to short term flat spotting in the tires. Follow the Service Procedure steps to correct the condition.
SSM 47625
Service Bulletin/Repair Instructions
Some 2014-2019 Fusion and 2017-2019 Escape vehicles equipped with a 1.5L Ecoboost engine may exhibit coolant consumption and white smoke concern. Follow the Cooling System Pressure Test procedure in Workshop Manual(WSM), Section 303-03, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If cooling system pressure drops 27.57kPa(4psi) after 5 hours and internal engine coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect cylinder block for erosion, pitting, and flatness. Defects will be between the engine block cylinders and cylinder bore bridges. If defects with the surface of the cylinder block and/or cylinder head are identified, follow WSM, Section 303-01A procedures for repairs. Complete cost cap as needed to determine the most cost effective repair.