Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 55142
Service Bulletin/Repair Instructions
Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern. If the concern pers
SSM 55100
Service Bulletin/Repair Instructions
For Various Ford and Lincoln vehicles, if diagnostics lead to the replacement of the front seat cushion cover J-clips, lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901
SSM 55031
Service Bulletin/Repair Instructions
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
TSB 26-2328
Service Bulletin/Repair Instructions
This bulletin supersedes 26-2194. Reason for update: update the Parts list to correct a part description " Loctite 638", update the claim quantity for the drain/fill plug, update the claim quantity of the wheel hub bolts (Corsair) and limited the parts list for Edge/Nautilus to only the rear drive unit fluid. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder chatter condition, most noticeable at low speeds turning No relevant diagnostic trouble codes (DTCs) present This may be due to internal rear drive unit (RDU) fluid contamination.
GSM-26.P0929 Escape
Over The Air
Quality improvements include: -Updates the gear shift lock diagnostic logic to prevent false wrench lights
TSB 26-2297
Service Bulletin/Repair Instructions
Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.
SSM 54939
Service Bulletin/Repair Instructions
Some 2020-2026 Corsair/Escape, 2021-2026 Bronco Sport, and 2022-2026 Maverick vehicles equipped with an 8F35 transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation. For claim
SSM 54918
Service Bulletin/Repair Instructions
Some of the following vehicles: 2025-2026 Mustang Mach-E vehicles built on or before 27-Jan-2026 2025-2026 Maverick/Bronco Sport vehicles built on or before 20-Jan-2026 2024-2026 Nautilus vehicles built on or before 02-Dec-2025 2023-2026 Escape/Corsair may exhibit reduced steering assist and a "Power Steering Assist Fault" message displayed in the instrument panel cluster (IPC) with the diagnostic trouble code (DTC) U2016:47 only, and no other steering DTCs stored in the power steering control module (PSCM). To correct this condition, reprogram the PSCM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 3C529 and labor operations 3504E and PSCM. If a software update is not available for the PSCM, the PSCM is already at the latest software level. Refer to Workshop Manual (WSM), Section 211-02 for normal diagnostics. If the vehicle does not exhibit any observable symptoms described above and the DTC is only present in continuous memory, this DTC should be ignored. No further service action
25B33
Other
Certain 2023-2025 Model Year Escape and Corsair, 2024-2025 Model Year Nautilus, 2025-2026 Model Year Bronco Sport and 2025 Model Year Maverick Vehicles Equipped with an Engine Block Heater System Block Heater Replacement
ACM-26.S Escape
Over The Air
Quality improvements include: -Addresses a potential communication condition that may result in a loss of radio audio.
TSB 26-2210
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Engine misfire condition * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0301, P0302, P0303, and/or P0304 stored in the powertrain control module (PCM)
SSM 54857
Service Bulletin/Repair Instructions
2020-2026 Explorer/Escape/Corsair, 2021-2026 Bronco Sport/Bronco, 2022-2026 Maverick, 2024-2026 Mustang/Ranger/Nautilus vehicles equipped with a 2.0L or 2.3L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 2.0L/2.3L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure been added. In addition, the wastegate actuator rod (9E408), associated retention springs (9342) and retaining clips (00817) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate actuator assembly.
TSB 26-2205
Service Bulletin/Repair Instructions
This bulletin supersedes 25-2346. Reason for update: add Bronco Sport and Escape vehicles and add labor operations to repair the rear right/left carpet area. Some of the vehicles listed in the Model statement above may exhibit a condition where the carpet is loose or torn near the front/rear scuff plate trim panel. This may be due to the carpet tearing at or near the retainer hole.
SSM 54825
Service Bulletin/Repair Instructions
Some 2023-2026 Escape vehicles equipped with an 8F35 transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0767, P0766 and/or P2703 stored in the powertrain control module (PCM) and harsh/no reverse engagement. This may be due to the selectable one-way clutch (SOWC). To correct the condition, remove the transmission. Refer to Workshop Manual (WSM) > Section 307-01. Disassemble the transmission only far enough to access the SOWC. Refer to WSM, Section 307-01 > Overhaul and perform Steps 34-66. Remove the SOWC assembly, disassemble the A-clutch and discard the SOWC. Refer to WSM, Section 307-01 > Overhaul and perform Steps 164-170. Assemble the new SOWC with the A-clutch components. Refer to WSM, Section 307-01 > Overhaul and perform Steps 173-179. The A-clutch seals can be reused unless damaged. Install the new SOWC and reverse the procedure to reassemble the transmission. Overhaul the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Replace the torque converter seal. Refer to WSM, Section 307-01
SSM 54797
Service Bulletin/Repair Instructions
Some 2020-2026 Corsair/Escape, 2021-2026 Bronco Sport, and 2022-2026 Maverick vehicles equipped with an 8F35 transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation.
TSB 26-2194
Service Bulletin/Repair Instructions
This bulletin supersedes 25-2627. Reason for update: To add a Step to reprogram the all-wheel drive (AWD) module for Bronco Sport vehicles. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder chatter condition, most noticeable at low speeds turning No relevant diagnostic trouble codes (DTCs) present This may be due to internal rear drive unit (RDU) fluid contamination.
SSM 54738
Service Bulletin/Repair Instructions
Some 2023-2025 Escape 1.5L/F-Super Duty/Transit vehicles may exhibit a lack of cooling from the heating, ventilation, and air conditioning (HVAC) system, which may be accompanied by abnormal rattling, grinding and/or squealing noises from the engine compartment. This may be due to damage to the air conditioning (A/C) compressor internal components and/or clutch assembly. Confirm ambient air temperature is above approximately 0°C (32.0°F). On the HVAC controls, set the temperature to full cold (not MAX A/C), select PANEL, set the fan speed to the highest setting and select the A/C button (indicator on). If the A/C compressor clutch engages and the A/C compressor is noisy, and/or the belt is slipping on the A/C compressor pulley or the A/C compressor is seized, install a new A/C compressor as indicated in Section 412-00 of the Workshop Manual (WSM). For claiming, use causal part 19703 and labor operation MT19700SSM up to 0.3 hours to check for a damaged compressor. If the compressor requires replacement, claim labor operations 19700A and 19700A4. Also claim available Service Labor Time Standards (SLTS) op
23B64
Other
Customer Satisfaction Program 23B64 Certain 2020-2024 Model Year Multiple Vehicle Lines Equipped with High Voltage Batteries Battery Energy Control Module (BECM) Software Update
SSM 54727
Service Bulletin/Repair Instructions
Some 2024 F-150/Escape/Corsair vehicles may exhibit no audio/no volume with diagnostic trouble code (DTC) U1A00:87 stored in the accessory protocol interface module (APIM). This may be due to the software in the front audio control module (ACM). To correct the condition, reprogram the ACM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 18C869 and labor operations 12651D and 12651D4.
SSM 54720
Service Bulletin/Repair Instructions
Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
TSB 26-2092
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2466 to add Bronco Sport, Escape, Maverick and Corsair, as well as removing Expedition and Navigator. One time use parts for Corsair and Bronco Sport were also added to the parts list. Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.
SSM 54630
Service Bulletin/Repair Instructions
Some 2024 F-150/Escape/Corsair vehicles may exhibit no audio/no volume with diagnostic trouble code (DTC) U1A00:87 stored in the accessory protocol interface module (APIM). This may be due to the software in the front audio control module (ACM). To correct the condition, reprogram the ACM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 18806 and labor operations 12651D and 12651D4.
SSM 54615
Service Bulletin/Repair Instructions
Some 2020-2026 Escape and 2021-2026 Corsair vehicles equipped with a 2.5L engine may exhibit a fuel door that won't open with diagnostic trouble code (DTC) P04CA stored in the powertrain control module (PCM). This may be due to an open circuit on circuit SBB05 and/or a damaged splice S133. Before performing the pinpoint test for P04CA in Workshop Manual (WSM), Section 310-00, inspect circuit SBB05 and splice S133 for damage such as an open circuit. Repair as necessary. Refer to Wiring Diagram, Cell 005. If no damage is found, refer to WSM, Section 310-00 for normal diagnostics. For claiming use causal 14290 and labor operations 12650D, 12650D45, and 12650D45WR.
SSM 54601
Service Bulletin/Repair Instructions
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
SSM 54593
Service Bulletin/Repair Instructions
Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and/or may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the high-pressure fuel pump causing fuel to enter the crankcase and reduce fuel pressure in the direct injection fuel rail. Diagnose this condition using Pinpoint Test HP located in Workshop Manual (WSM), Section 303-04. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. Repair as necessary outside of this article. For claiming, if high-pressure fuel pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article.
TSB 25-2627
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2552 to update the Parts List Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder chatter condition, most noticeable at low speeds turning No diagnostic trouble codes DTCs present This may be due to rear drive unit internal (RDU) fluid contamination.
TSB 26-2030
Service Bulletin/Repair Instructions
This article supersedes TSB 26-2012 to update APIM software version to 24127 Some of the vehicles listed in the Model statement above may exhibit various electrical symptoms, and/or a no crank/no start condition related to a 12V battery drain condition. This may be due to the software level of the affected module(s).
TSB 26-2012
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2384 to update Service Procedure enhancements and labor allowances by operation in place of AP (Actual Programming) Time. Some of the vehicles listed in the Model statement above may exhibit various electrical symptoms, and/or a no crank/no start condition related to a 12V battery drain condition. This may be due to the software level of the affected module(s).
SYNC-25.2.1.6.5.2 Escape
Over The Air
Quality Improvements Include: - Bug Fixing and Feature improvements. - Resolves black screen issue caused when there is no SiriusXM disk space.
SSM 54491
Service Bulletin/Repair Instructions
Some 2021-2026 Escape/Corsair vehicles equipped with a roof opening panel may exhibit a sunshield with localized looseness/sagging or binding/inoperative. This may be due to a broken or missing sunshield fabric retainer/clip. A revised sunshield clip (5452118) is available to address this condition. It is not necessary to replace the entire sunshield assembly if the clip(s) are broken or missing. Refer to Workshop Manual (WSM), Section 501-17 Roof Opening Panel for inspection and replacement of the roof opening panel shield clip.
25L02
Other
Special Field Action 25L02 Certain 2017-2024 Model Year California Emissions-Certified Vehicles Transmission Control Assembly Reimbursement
TSB 25-2381
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2412 to update the Service Procedure and the Part List. Some of the vehicles listed in the Model statement above may exhibit at least one of the following: Illuminated malfunction indicator lamp (MIL) Diagnostic trouble code (DTC) P0767, P0766 and/or P2703 stored in the powertrain control module (PCM). Harsh reverse or intermittent no reverse engagement. This may be due to an internal mechanical concern with the selectable one-way clutch (SOWC).
SSM 54403
Service Bulletin/Repair Instructions
* 2021-2024 Bronco Sport built on or before 15-Dec-2024<br /> * 2022-2024 Mustang Mach-E<br /> * 2022-2025 Escape built on or before 22-May-2025<br /> * 2024 Maverick vehicles built on or after 17-Jan-2024<br /> <br /> Some of the above vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct the condition, reprogram the GSM module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 7P155 and labor operation numbers 7001D and 7001D4.
TSB 25-2552
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2351 to update the Service Procedure Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder chatter condition, most noticeable at low speeds turning No diagnostic trouble codes DTCs present This may be due to rear drive unit internal (RDU) fluid contamination.
TSB 25-2479
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2249 to update the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit a "Pre-Collision Assist Not Available" message in the IPC and at least one of the following conditions: Various driver assistance feature warning messages in the instrument panel cluster (IPC): - "Blind Spot System Fault" - "Cross-Traffic System Fault" - "Front Camera Fault - Service Required" Various data or lost communication diagnostic trouble codes (DTCs) stored in various modules Ford Diagnosis and Repair System (FDRS) scan tool cannot establish connectivity with the image processing module A (IPMA) during a self-test. This may be due to the software installed in the IPMA. *** MODEL SECTION **** 2023-2026 Escape equipped with minor feature code: DBCAB or DBCAA 2023-2026 Corsair equipped with minor feature code: DBCBC
SSM 54312
Service Bulletin/Repair Instructions
Some 2020-2026 Escape and 2021-2026 Corsair PHEV vehicles may require inspection of the high voltage battery due to rust, scratches, curb strikes, road debris, or other minor damage. Section 414-03A of the Workshop Manual (WSM) has recently been updated to improve diagnostics for such damage and provides a list of low-level serviceable components for instances where replacement of the high voltage battery assembly is not warranted. Refer to WSM, Section 414-03A High Voltage Battery, Mounting and Cables > Diagnosis and Testing > High Voltage Battery Minor Damage Inspection. The Ford New Vehicle Limited Warranty covers manufacturing defects resulting from a defect in factory supplied materials or workmanship. Please refer to the Warranty section WHAT IS NOT COVERED, which includes curb strikes and accidents.
SSM 54313
Service Bulletin/Repair Instructions
Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
SSM 54288
Service Bulletin/Repair Instructions
Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern.
SSM 54250
Service Bulletin/Repair Instructions
Some 2024-2025 Escape Hybrid/Maverick Hybrid/Nautilus Hybrid/F-150 non-Lightning/F-Super Duty/Bronco and 2025 Expedition/Navigator/Ranger vehicles where customers have installed an aftermarket supplemental braking system may experience a discharged 12-volt battery after recreational towing. This may be due to the supplemental braking system keeping the vehicle awake during brake applications. Advise customers that while recreational towing the vehicle with a supplemental braking system installed, it is recommended to use a 12-volt battery charger connected to a power source external to the vehicle being towed. The Owners Manual is in process of being updated with this information.
SSM 54246
Service Bulletin/Repair Instructions
A small percentage of 2023-2025 Escape/Corsair vehicles may exhibit a "Pre-Collision Assist Not Available" warning message displayed in the instrument panel cluster (IPC) along with other various driver assistance feature warning messages and various invalid data/lost communication diagnostic trouble codes (DTCs) stored in various modules after Technical Service Bulletin (TSB) 25-2249 has been performed. The reoccurrence of these symptoms is related to a different root cause. This condition does not affect vehicle durability, and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in late October 2025. Replacement of the image processing module A (IPMA) will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.
TSB 25-2438
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2143 to update the production fix date. Some of the vehicles listed in the Model statement above may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle.
SSM 54202
Service Bulletin/Repair Instructions
Some 2023-2025 Explorer (rear windows only), Bronco Sport, Escape, and Maverick vehicles equipped with minor feature code B2DAC may exhibit an inoperative passenger front and/or rear window switch. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle Information or double-clicking the vehicle identification number (VIN) in the upper left corner of Professional Technician System (PTS). This may be due to an open diode in one of the passenger window switches. To correct the condition, replace the passenger window switch of the affected window. If the condition persists continue with normal diagnostics. Refer to Workshop Manual, Section 501-11. For claiming, use causal part 14529 and labor operation 14529A in the Service Labor Time Standards (SLTS) Manual.
25H03
Other
Harvest Program 25H03 Certain 2024 - 2025 Model Year Bronco, Bronco Sport, Corsair, Escape, Explorer, Maverick, Mustang, and Ranger Vehicles with 1.5L, 2.0L, or 2.3L Engine Spark Plug Replacemen
TSB 25-2384
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2081 to remove the Parts List and update the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit a 12V battery drain condition. This may be due to the software level of the affected module(s).
SSM 54137
Service Bulletin/Repair Instructions
Various 2021-2025 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit "Please Check Surroundings For Safety" or "Full View Not Available" messages when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
SSM 54114
Service Bulletin/Repair Instructions
Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern. If the concern pers
TSB 25-2362
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit an incorrectly illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P27B2 stored in the secondary on-board diagnostic control module C (SOBDMC). This may be due to the software in the SOBDMC.
SSM 54089
Service Bulletin/Repair Instructions
Some 2023-2024 Escape vehicles built on 01-Jan-2023 and through 07-Jun-2024 equipped with an 8-inch center display screen may experience a rear view camera image in the vehicle's center display screen that is missing the active guidelines overlay and zoom button icon, while in reverse. This may be due to the software in the body control module (BCM). To correct the condition, download and run the "BCM - Body Control Module (BCM) Software Update" application in the Ford Diagnosis and Repair System (FDRS). After the BCM software has been updated, download and run the "Local Interconnect Network (LIN) New Module Initialization" application.
SSM 54090
Service Bulletin/Repair Instructions
Some 2021-2025 Ford and Lincoln vehicles equipped with SYNC4/Digital Experience may exhibit an unsuccessful telematics control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.
TSB 25-2351
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2386 to update the Service Procedure and Part List. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder chatter condition, most noticeable at low speeds turning No diagnostic trouble codes DTCs present Note: Three (3) new Essential Special Service Tools (ESSTs) are required to service the internal clutch pack on vehicles equipped with a single active torque rear drive unit (RDU) only. These ESSTs are expected to ship to all dealers (US, Canada, Puerto Rico and Mexico) in September 2025. ESST packages were shipped to 100 selected dealers in the US and Canada in May 2025, based on RDU part sales activity. The RDU Internal Clutch Kit and Adhesive Sealant are currently under restricted ordering to ensure ample supply of parts are available to dealers with the ESSTs. All parts are expected to be available for open order by Q4 2025, when the ESSTs are planned to arrive at all dealers. Note: For dealers with the ESSTs and a vehicle in the service department that requires a repair using the new RDU Internal Clutch
SSM 54068
Service Bulletin/Repair Instructions
Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Disconnect the charge air cooler inlet and outlet hose, overflow hose, upper and lower hose of the radiator and position these components aside. Disconnect the inlet and outlet coolant hoses of the heater core and position
TSB 25-2326
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450 stored in the powertrain control module (PCM). This may be due to the software level of the PCM.
SSM 54041
Service Bulletin/Repair Instructions
Some 2023-2025 Explorer (rear windows only), Bronco Sport, Escape, and Maverick vehicles equipped with minor feature code B2DAC may exhibit an inoperative passenger front and/or rear window. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle Information or double-clicking the vehicle identification number (VIN) in the upper left corner of Professional Technician System (PTS). This may be due to an open diode in the window switch. To correct the condition, replace the window switch of the affected window. If the condition persists continue with normal diagnostics. Refer to Workshop Manual, Section 501-11. For claiming, use causal part 14529 and labor operation 14529A in the Service Labor Time Standards (SLTS) Manual.
ABS-24.80.6 Escape
Over The Air
Software Update: Quality improvements include: -Addresses a false "Service the park brake" message -Quicker brake release when shifting to reverse -Customers will receive alerts if the park brake gets stuck in the release maneuver, or if a shift to neutral occurs with driver off brakes
PCM-25.10.2 Escape
Over The Air
Quality improvements include: -Addresses a potential Malfunction Indicator Lamp caused by two Diagnostic Trouble Codes triggered by a random engine misfire in the first thousand revolutions of vehicle start
SSM 53971
Service Bulletin/Repair Instructions
Some 2023-2025 Escape vehicles equipped with a 1.5L/2.0L EcoBoost engine, 2023-2025 Corsair vehicles equipped with a 2.0L EcoBoost engine, 2024-2025 Nautilus vehicles equipped with a 2.0L EcoBoost engine, 2024-2025 Mustang vehicles with a 2.3L EcoBoost engine, and 2025 Bronco/Explorer/Ranger vehicles equipped with a 2.3L EcoBoost engine may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). This may be due to the spark plugs and/or ignition coils. To correct the condition, refer to Workshop Manual (WSM), Section 303-07 for normal diagnostics.
SSM 53973
Service Bulletin/Repair Instructions
Some 2021-2024 Edge/Nautilus, 2021-2025 Bronco/Bronco Sport/E-Series/Escape/Corsair/Expedition/Navigator/Explorer/Aviator/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.
SSM 53966
Service Bulletin/Repair Instructions
Some 2021-2025 Ford/ Lincoln vehicles equipped with SYNC4 may not be able to perform an update to the accessory protocol interface module (APIM). This may be due to the software in the APIM. Ford Engineering has de-activated the ability to update these SYNC4 APIM modules as applicable, and the Ford Diagnosis and Repair System (FDRS) will not present an update for the APIM module. Some existing directed repairs may be impacted, check Professional Technician System (PTS) before attempting any specific technical service bulletin (TSB)/special service message (SSM) and check field service action (FSA) landing pages before attempting any FSA repairs. For any vehicle repairs requiring a software update that includes an APIM update in the programming sequence, if the 5-digit product code for the APIM software is equal to or lower than 23187, do not attempt to update affected modules at this time. To determine the 5-digit product code for the APIM software on the vehicle, while the vehicle center display screen is powered up with ignition in run or accessory, go to Settings > General > About SYNC.
IPMA-25.204.8.29 Escape
Over The Air
Quality improvements include: -Addresses pop ups in the cluster and no Advanced Driver Assistance System functionality caused the Image Processing Module A being offline
TSB 25-2249
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Various driver assistance feature warning messages in the instrument panel cluster (IPC): - "Blind Spot System Fault" - "Cross-Traffic System Fault" - "Front Camera Fault - Service Required" - "Pre-collision Assist Not Available" Various data or lost communication diagnostic trouble codes (DTCs) stored in various modules Ford Diagnosis and Repair System (FDRS) scan tool can not establish connectivity with the image processing module A (IPMA) during a self test. This may be due to the software installed in the IPMA. *** MODEL SECTION **** 2023-2025 Escape equipped with minor feature code: DBCAB 2023-2025 Corsair equipped with minor feature code DBCBC
SSM 53764
Service Bulletin/Repair Instructions
Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
SSM 53759
Service Bulletin/Repair Instructions
After replacement of any TRON module, the gateway module (GWM) and the TRON capable modules can set diagnostic trouble codes (DTCs) U211A, U211B, U211C, U3034, U3035, U3036, U35D9, U35DA and/or U35DB if the secret authentication security keys are not aligned between the modules, a loss of communication is occurring between modules and/or a module is not responding. This may be a result of missing the new module secret authentication security key obtained when running the Ford Diagnosis and Repair System (FDRS) "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure after replacement. When replacing a TRON capable module, run the FDRS "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure in the GWM tool box, not in the toolbox of the module with the DTC's, to distribute a new set of secret authentication security keys to all TRON-capable modules. Using the specific vehicle identification number (VIN), refer to Workshop Manual (WSM), Section 418-00 and 418-01 for updated DTCs, applicable TRON module listings and pinpoint tests.
SSM 53760
Service Bulletin/Repair Instructions
Some 2023-2024 Escape/Corsair vehicles equipped with driver assistance features with minor feature code DBCAB for Escape and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC. Additionally, some modules may store invalid data/lost communication related DTCs. The image processing module A (IPMA) should not store these DTCs. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This condition may be due to the software in the IPMA, causing it to not communicate on the network. To restore communication and functionality, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the Ford Diagnosis and Repair System (FDRS) scan tool. Once IPMA communication has been restored, download and run the "IPMA - Image Processing Module (IPMA) Alignment"
TSB 25-2176
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P144F stored in the powertrain control module (PCM). This may be due a concern with the fuel pump and sender unit.
24N08 -S1
Other
Customer Satisfaction Program 24N08 - Supplement #1 Certain 2021-2024 Bronco Sport, Escape, Mach-E, and 2022-2024 Maverick Vehicles Driver’s Side Seat Buckle Replacement
OTASYNC-2.1.6.1.1Escape
Over The Air
Priority Update - Voice Features Accessory Protocol Interface Module SYNC-2.1.6.1.1 1 SYNC® Enhancements We have made updates to your vehicle's software for the voice recognition and text to speech features.
SSM 53638
Service Bulletin/Repair Instructions
After replacement of any TRON module, the gateway module (GWM) and the TRON capable modules can set diagnostic trouble codes (DTCs) U211A, U211B, U211C, U3034, U3035, U3036, U35D9, U35DA and/or U35DB if the secret authentication security keys are not aligned between the modules, a loss of communication is occuring between modules and/or a module is not responding. This may be a result of missing the new module secret authentication security key obtained when running the Ford Diagnosis and Repair System (FDRS) "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure after replacement. When replacing a TRON capable module, run the FDRS "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure to distribute a new set of secret authentication security keys to all TRON-capable modules. Using the specific VIN, refer to Workshop Manual (WSM), Section 418-00 and 418-01 for updated DTCs, applicable TRON module listings and pinpoint tests.
SSM 53634
Service Bulletin/Repair Instructions
Drivers of some 2020-2025 Escape, 2021-2025 Bronco Sport and 2022-2025 Maverick vehicles may report the uncommanded locking of the driver door after the door is closed. This may be due to the driver placing their hand on the interior front door handle and inadvertently pushing the manual door lock toggle into the lock position. If the lock and latching mechanisms are functioning normally, and if there are no related diagnostic trouble codes (DTCs) or other issues identified, then the system is operating as designed.
TSB 25-2143
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2095 to update the Service procedure. Some of the vehicles listed in the Model statement above may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle.
SSM 53601
Service Bulletin/Repair Instructions
Some 2020-2023 Explorer/Aviator, 2020-2025 Police Interceptor Utility, 2020-2025 Escape/Corsair, 2022-2025 Maverick, and 2024-2025 Nautilus vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450:00 stored in the powertrain control module (PCM). This may be due to an evaporative emission system concern or may also be caused by the customer overfilling the fuel tank. If this condition occurs, perform normal diagnosis per Workshop Manual (WSM) Section, 303-13 and repair as necessary. Inform the customer that the condition may have been caused by overfilling of the fuel tank and to not top-off the fuel tank when the fuel pump nozzle automatically shuts off for the first time. Refer the customer to the Fuel and Refueling section of their Owner Manual for additional information.
SSM 53569
Service Bulletin/Repair Instructions
Some 2021-2025 Ford and Lincoln vehicles may exhibit diagnostic trouble code (DTCs) U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.
TSB 25-2133
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with DTCs P0300 and P0316. This concern may occur after initial engine start up following an overnight cold soak.
24-OTA ABS-24.80.6 Escape
Over The Air
Quality improvements include: -Faster parking brake release when shifting to reverse -Alert message when shifting to neutral without pressing the brake pedal -Reduces potential no start events due to ABS after OTA update. -If the vehicle shuts off with Auto Vehicle Hold on, it’ll wake up with AVH on. -Addresses erroneous "Service Park Brake Limited Function" message at start up. - A Check Engine Light may appear after the update, causing no effect on the vehicle. This clears after a few drive cycles.
TSB 25-2095
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2051 to update the parts list. Some of the vehicles listed in the Model statement above may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle.
TSB 25-2102
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit an incorrectly illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P144B stored in the powertrain control module (PCM) without driving performance concerns. This may be due to the PCM software.
TSB 25-2107
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2055 to update the labor time description.
TSB 25-2081
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2143 and 24-2288 to update the Service Procedure and labor times associated with the Service Procedures from M-time to AP-time. Some of the vehicles listed in the Model statement above may exhibit a 12V battery drain condition. This may be due to the software level of the affected module(s).
24N08
Other
Certain 2021-2024 Bronco Sport, Escape and 2022-2024 Maverick Vehicles Driver’s Side Seat Buckle Replacement
TSB 25-2074
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2384 to update the vehicle lines and model years affected.
SSM 53468
Service Bulletin/Repair Instructions
Some 2021-2024 Mustang Mach-E and 2023-2025 Escape/Corsair vehicles may exhibit only continuous memory diagnostic trouble code (CMDTC) U2016:47 stored in the power steering control module (PSCM) after a self test is performed with Ford Diagnosis and Repair System (FDRS) scan tool.
SSM 53465
Service Bulletin/Repair Instructions
Some 2021-2024 Bronco Sport, 2020-2024 Escape/Corsair/Edge/Nautilus/Transit Connect and 2022-2024 Maverick vehicles may exhibit erratic shifting and/or a transmission fluid venting condition. If during the preliminary inspection the transmission fluid is found to be a foamy pink color, this may indicate possible cross contamination of engine coolant and transmission fluid due to an internally leaking transmission fluid cooler assembly.
24P28
Other
Customer Satisfaction Program 24P28 Certain 2025 Model Year F-650/F-750, 2024 Model Year Super Duty, Transit and Escape Vehicles A/C Compressor Inspection
SSM 53419
Service Bulletin/Repair Instructions
Some 2023-2024 Escape/Corsair vehicles equipped with driver assistance features with minor feature code DBCAB for Escape and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC.
TSB 25-2055
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * General system performance/stability/intermittent system reboot * Intermittent wireless CarPlay or Android Auto function * Phone related concerns with intermittent no audio or static * Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto * Alexa function consistency and stability * Charge Assist/Public Charging app inoperative (e-Transit only) This may be due to a concern with the software in the accessory protocol interface module (APIM).
SSM 53417
Service Bulletin/Repair Instructions
Some 2024-2025 Escape and 2025 Bronco Sport vehicles equipped with a 1.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with only diagnostic trouble codes (DTCs) P0300 and P0316 stored in the powertrain control module (PCM).
TSB 25-2051
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2031 to update the parts list. Some of the vehicles listed in the Model statement above may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity.
TSB 25-2031
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2348 to update vehicles affected and labor operation description. Some of the vehicles listed in the Model statement above may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle.
OTA ECG-24.2.5.7 Escape
Over The Air
Quality improvements include: -Enahnced connectivity experience -Enhanced software update performance
SSM 53345
Service Bulletin/Repair Instructions
Some 2021-2024 Mustang Mach-E and 2023-2025 Escape/Corsair vehicles may exhibit only continuous memory diagnostic trouble code (CMDTC) U2016:47 stored in the power steering control module (PSCM) after a self test is performed with Ford Diagnosis and Repair System (FDRS) scan tool.
SSM 53293
Service Bulletin/Repair Instructions
Some 2024-2025 Escape vehicles equipped with a 1.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300 and P0316 stored in the powertrain control module (PCM).
24-OTA ABS 24.80.6 Escape
Over The Air
Quality improvements include: -Faster parking brake release when shifting to reverse -Alert message when shifting to neutral without pressing the brake pedal - Reduces potential no start events due to ABS after OTA update. -if the vehicle shuts off with Auto Vehicle Hold on, it’ll wake up with AVH on. -Addresses erroneous "Service Park Brake Limited Function" message at start up.
SSM 53224
Service Bulletin/Repair Instructions
When replacing the 12V battery on 2022-2025 Escape hybrid vehicles, download and run the Battery Type Configuration application using the latest version of the Ford Diagnostic and Repair System (FDRS) scan tool.
TSB 24-2421
Service Bulletin/Repair Instructions
Some 2020-2024 Escape and Corsair Vehicle built on or before 17-Aug 2024 equipped with the 8F35 or the HF45 transmission may exhibit a click or ting noise during acceleration from a stop, or in some cases during the end of a stop event.
TSB 24-2384
Service Bulletin/Repair Instructions
Some 2023-2025 Escape/Corsair vehicles equipped with a 1.5L or 2.0L EcoBoost engine, 2024 Mustang vehicles equipped with a 2.3L EcoBoost engine, 2024-2025 Nautilus, and 2025 Explorer vehicles equipped with a 2.3L EcoBoost engine may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM).
SSM 53141
Service Bulletin/Repair Instructions
Some 2023-2024 Escape/Corsair vehicles equipped with driver assistance features with minor feature code DBCAB for Escape and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC
TSB 24-2347
Service Bulletin/Repair Instructions
Some 2020-2024 Escape and Corsair Vehicle built on or before 17-Aug 2024 equipped with the 8F35 or the HF45 transmission may exhibit a click or ting noise during acceleration from a stop, or in some cases during the end of a stop event.
TSB 24-2348
Service Bulletin/Repair Instructions
Some 2020-2024 Escape and 2021-2024 Bronco Sport vehicles may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity.
SSM 53088
Service Bulletin/Repair Instructions
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed.
24-OTA SU 10.1.1 Escape
Over The Air
'-Improved connectivity. -Reduces TCU based Key Off Load battery drain. - Map orientation improvement - removes false"IP Configuration Failure" message when wrong WiFi password is entered. - Improves functionality of Stolen Vehicle Services
24-OTA SYNC 2.1.6.1 Escap
Over The Air
Quality improvements: -Addresses Accessory protocol Interface Module reboot at start up -Charge Status messaging strategy that also follows the IPC strategy.
TSB 24-2326
Service Bulletin/Repair Instructions
Some 2020-2024 Escape and 2021-2024 Bronco Sport vehicles may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle. To correct the condition, follow the Service Procedure to install brake pads with clips and if necessary, install the rear reinforced caliper bushings.
SSM 53047
Service Bulletin/Repair Instructions
Some 2023-2024 Escape vehicles may exhibit a condition where the image processing module A (IPMA) is unable to program with a message displayed in the Ford Diagnosis and Repair System (FDRS) scan tool indicating "Procedure Unsuccessful-Call Get Restore Invalid Hardware: RJ6T-14H107-BBB".
SSM 53040
Service Bulletin/Repair Instructions
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
SSM 53018
Service Bulletin/Repair Instructions
Some 2021-2024 Ford and Lincoln vehicles may exhibit diagnostic trouble codes (DTCs) U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.
SSM 52999
Service Bulletin/Repair Instructions
Some 2023-2024 Escape vehicles built on or before 21-Mar-2024 and equipped with a B&O audio system may exhibit an intermittent no audio condition with diagnostic trouble code (DTC) U0238 stored in the audio control module (ACM) and/or in the accessory protocol interface module (APIM).
OTA SU 10.1.0 Escape
Over The Air
Quality improvments include: - Allows the SYNC strategy for Charge Status messaging to match the Cluster messaging strategy - Improved SYNC stabilty. - Provides enhanced security when accessing external content
SSM 52915
Service Bulletin/Repair Instructions
Some 2024 Bronco Sport/Escape and 2025 Explorer vehicles may have been ordered with a DIO Securicode® RKE wired keypad that requires installation and enabling by the dealer prior to delivery.
24U10
Service Bulletin/Repair Instructions
In some of the affected vehicles with low time in service, the Air Conditioning (A/C) compressor may experience an internal failure that can cause loss of A/C performance or function.
SSM 52895
Service Bulletin/Repair Instructions
Some 2020-2024 Escape, 2021-2024 Bronco Sport and 2022-2024 Maverick vehicles may exhibit the uncommanded locking of the driver door after the door is closed.
TSB 24-2193
Service Bulletin/Repair Instructions
Some 2023-2024 Escape vehicles equipped with a HF45 transmission may exhibit an illuminated powertrain malfunction (wrench) indicator with DTC P07E6 stored in the inverter system controller SOBDMC, the GSM will display a flashing P on the dial, the P on the instrument cluster is not illuminated, and the vehicle will be stuck in the park (P) position.
24P23
Service Bulletin/Repair Instructions
On some of the affected vehicles, an intermittent open circuit at an electrical connection integrated into the fuel tank may result in an inaccurate fuel level measurement
24-OTA 24.2.5.6.2 Escape
Over The Air
Quality Improvements include: - Reduction in Key off load battery drain via Enhanced Central Gateway (ECG) controlled reset. - Addresses Accessory Protocol Interface Module (SYNC) displaying update status as not completed. - Addresses potential vehicle no start condition post OTA update.
SSM 52805
Service Bulletin/Repair Instructions
Some 2023-2024 Escape/Corsair vehicles equipped with driver assistance features with minor feature code DBCAB for Escape or minor feature code DBCBC for Corsair may exhibit various driver assistance feature warning messages displayed in the IPC.
TSB 24-2246
Service Bulletin/Repair Instructions
Some 2023-2024 Escape vehicles built on or before 10-Jun-2024 and equipped with 1.5L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0496 stored in the powertrain control module (PCM). To correct this condition, follow the Service Procedure to reprogram the PCM.
SSM 52795
Service Bulletin/Repair Instructions
Some 2024 Bronco Sport/Escape and 2025 Explorer vehicles may have been ordered with a DIO Securicode® RKE wired keypad that requires installation and enabling by the dealer prior to delivery.
SU 24.2.4.10 Escape
Over The Air
Quality improvements include: - Improved Phone as A Key functionality post Enhanced Central Gateway module (ECG) reset. -Minor quality fixes in Enhanced Central Gateway module (ECG) Software, not affecting vehicle operation. - Addresses potential vehicle no start after OTA update.
SSM 52788
Service Bulletin/Repair Instructions
Some 2023-2024 Escape/Corsair, 2024 Nautilus vehicles may exhibit various AWD/4WD/4x4 warning messages displayed in the message center with loss of AWD function for the remainder of the active key cycle. DTCs C0095, C05D9:74, P060A, P060B, P060C, and/or P1674 may be stored in the AWD module. This condition may be due to the software in the AWD module.
SSM 52771
Service Bulletin/Repair Instructions
When performing diagnosis on 2024 Bronco Sport/Escape/Corsair vehicles for a "Fuel Level Low" warning displayed in the instrument panel cluster (IPC) and an illuminated malfunction indicator (MIL) lamp with diagnostic trouble code (DTC) P1346:13 stored in the IPC and/or DTC P2068 stored in the powertrain control module (PCM) when the fuel level is not low, pinpoint test C in Workshop Manual, Section 310-01 has been updated to better identify root cause of a "Fuel Level Low" symptom.
SSM 52774
Service Bulletin/Repair Instructions
Some 2020-2024 Escape/Explorer, 2021-2024 F-150, 2022-2024 Maverick and 2024 Nautilus vehicles equipped with a full hybrid electric vehicle (FHEV) powertrain may exhibit a cable connection error screen from the Midtronics xRC-3363 High Voltage Battery Rescue Charger. The xRC-3363 will prompt the technician to verify the low voltage connections when no actual fault is present. This may be due to the software level of the Midtronics xRC-3363 High Voltage Battery Rescue Charger.
24U06 S1
Service Bulletin/Repair Instructions
Certain 2024 Model Year Bronco Sport, Escape, and Explorer Keyless Entry Remote Control Replacement REASON FOR THIS SUPPLEMENT • Affected Vehicle Build Dates: The build date range for the affected vehicles has been updated to include additional vehicle population. • Technical Instructions: Remote control serial number identification inspection has been updated.
ECG-24.2.4.9 Escape
Over The Air
Quality improvements include: - Numerous minor quality fixes in ECG Software, not affecting vehicle operation. - Improves connectivity - 23 MY Eliminates a post OTA uneccessary message ""Stop Safely Now"" at startup. Clears at next key cycle.
24-OTA IPC-24.17 Escape
Over The Air
Quality improvements include: - Correct navigation/turn-by-turn indication in Instrument Cluster while entering a roundabout. - Gas DTE (Distance To Empty) indication appears continuously when scrolling through all Info on Demand screens.
SSM 52656
Service Bulletin/Repair Instructions
Some 2021-2024 F-150/Bronco and 2023-2024 Escape/F-Super Duty vehicles built with SYNC 4 require a connected phone with Android Auto or Apple CarPlay active to enable voice interactions and use of the steering wheel voice control button. This is due to the affected vehicles not having built in voice interactions capability. Vehicles with built in voice interaction capability can be identified as also being equipped with the built in connected navigation feature which includes a navigation tab on the center display screen. Diagnostics should only be performed for voice interactions on vehicles equipped with built in voice interaction capability or with Android Auto or Apple CarPlay active.
SSM 52633
Service Bulletin/Repair Instructions
Some 2020-2024 Escape/Corsair, 2021-2024 Bronco Sport/F-150, and 2022-2024 Maverick vehicles may exhibit a condition where the door(s) do not open using the exterior door handle(s). This may be due to an enabled door reinforcement inertia lock within the exterior door handle. This condition occurs when the doors are closed or opened with excessive force. To correct this condition, follow the door reinforcement inertia lock rest procedure that has been added to Section 501-14 of the Workshop Manual under General Procedures. For claiming, use causal part 78219A64.
SSM 52630
Service Bulletin/Repair Instructions
Some 2023-2024 Escape/Corsair vehicles equipped with a 1.5L or 2.0L EcoBoost engine, 2024 Mustang vehicles equipped with a 2.3L EcoBoost engine, and 2024 Nautilus vehicles may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). If the codes are stored in the PCM, remove and inspect the condition of all the spark plugs. If all spark plugs are found to be free of damage, replacement of the spark plugs is not necessary. Refer to the Workshop Manual and perform normal diagnostics. If any spark plugs appear to be damaged, use a borescope to inspect the condition of the cylinder walls. If the cylinder walls are scored/scraped/damaged, replace the long block engine assembly (6006) to resolve this condition. If the cylinder walls are not scored/scraped/damaged, replace the damaged spark plug(s) and advise the customer that engineering is investigating this issue. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
TSB 24-2139
Service Bulletin/Repair Instructions
Some 2020-2024 Escape and Corsair Vehicle equipped with the 8F35 or the HF45 transmission may exhibit a click or ting noise during acceleration from a stop, or in some cases during the end of a stop event. This may be due to the front half shaft sticking to the wheel bearing surface. To correct this condition, perform the Service Procedure below to lubricate the halfshaft and wheel bearing hub assembly mating surface.
SSM 52574
Service Bulletin/Repair Instructions
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.
SSM 52543
Service Bulletin/Repair Instructions
Some 2021-2024 F-150-3.5L FHEV, 2020-2024 Explorer 3.3L FHEV, 2020-2024 Escape 2.5L FHEV, and 2022-2024 Maverick 2.5L FHEV vehicles may exhibit an illuminated MIL with DTC P237F and/or P2C23 stored in the powertrain control module (PCM) and no affect on drivability. This may be due to seal damage, corrosion and/or water intrusion in the exhaust coolant temperature (ECT) sensors 3 and/or 4 connector. Visual inspection should be completed on ECT3 and ECT4 sensors and mating connections for seal damage, water intrusion, and corrosion. If seal damage, water intrusion or corrosion is present, repair per cell 5 of the Wiring Diagram, then apply Motorcraft® XG-12 Electrical Grease to the female/vehicle side of the harness. This inspection of ECT3 and ECT4 sensors should be completed prior to starting the appropriate pinpoint test in Section 303-03 of the Workshop Manual (WSM). If DTCs P237F and/or P2C23 do not return, no further action is necessary and the replacement of the entire exhaust heat exchanger assembly is not required. If P237F and/or P2C23 returns, follow the pinpoint test in Section 303-03 of the WSM for further diagnostics.
SSM 52515
Service Bulletin/Repair Instructions
Some 2020-2024 Escape and 2021-2024 Bronco Sport vehicles may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. Ford is aware of the concern and this condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected by the 4th quarter of 2024. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
24U06
Service Bulletin/Repair Instructions
Certain 2024 Model Year Bronco Sport, Escape, and Explorer - Keyless Entry Remote Control Replacement
SSM 52501
Service Bulletin/Repair Instructions
Some 2023-2024 Escape vehicles equipped with a 1.5L engine may require a cylinder head replacement as directed by other service bulletins. It is not necessary to discard the 17 valve cover bolts during disassembly; these bolts can be reused up to 3 times. The Workshop Manual (WSM), Section 303-01A, is scheduled to be updated by the end of June 2024.
SSM 52419
Service Bulletin/Repair Instructions
Some 2023-2024 Escape/Corsair vehicles equipped with a 1.5L or 2.0L EcoBoost engine, 2024 Mustang vehicles equipped with a 2.3L EcoBoost engine, and 2024 Nautilus vehicles may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). If the codes are stored in the PCM, remove and inspect the condition of all the spark plugs. If any spark plugs appear to be damaged, use a borescope to inspect the condition of the cylinder walls. If the cylinder walls are scored/scraped/damaged, replace the long block engine assembly (6006) to resolve this condition. If the cylinder walls are not scored/scraped/damaged, replace the damaged spark plug(s) and advise the customer that engineering is investigating this issue. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
OTAPU0227VIRBSEs
Service Bulletin/Repair Instructions
Quality improvements include: Numerous minor quality fixes in ECG RC9 which are not customer facing.
SSM 52410
Service Bulletin/Repair Instructions
Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
SSM 52368
Service Bulletin/Repair Instructions
2024 Escape and Bronco Sport vehicles equipped with 1.5L engines should add local fuel once the vehicle arrives at the dealership to reduce the risk of various engine performance concerns such as: rough operation, idle quality, engine misfires, lack or loss of engine power. These conditions may occur due to different fuel specifications between the manufacturing plant and the final market. Make sure that the vehicles in stock have local fuel added.
SSM 52369
Service Bulletin/Repair Instructions
2024 Escape/Bronco Sport vehicles equipped with 1.5L engines should not be taken out of transport mode before customer delivery to reduce the risk of various driving performance concerns such as: rough operation, idle quality, engine misfires, lack or loss of engine power. These conditions may occur due to carbon fouled spark plugs from repeated engine ignition starts without driving the vehicle to normal operation temperatures 179ðF-206ðF (82ðC-97ðC) during cold weather. Make sure that the vehicles in stock are in transport mode before customer delivery. Refer to the Workshop Manual (WSM), Section 419-10 Malfunction Electronic Modules > General Procedures.
SSM 52345
Service Bulletin/Repair Instructions
Some 2022-2024 various Ford/Lincoln vehicles equipped with SYNC 4 may experience concern where customers are receiving an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 52335
Service Bulletin/Repair Instructions
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 52328
Service Bulletin/Repair Instructions
Some 2021-2024 Bronco/F-150, 2023-2024 Escape/F-Super Duty vehicles equipped with SYNC 4 may experience a concern during accessory protocol interface module (APIM) programming where the vehicle's center display screen indicates USB Error. This may be due to a lack of memory space available to perform the APIM software update. If it is a memory concern, the Ford Diagnosis and Repair System (FDRS) will provide an option to delete the voice application. Re-enter the module programming and when prompted, do not select first option - SYNC Module (APIM) Software Update, select the second option - Delete Voice Application(s) From Module. Once deleted, run the SYNC Module (APIM) Software Update as directed, this will update the software and automatically reload the voice app. If the voice delete option is not available, continue with normal diagnostics in the Workshop Manual, Section 418.
SSM 52314
Service Bulletin/Repair Instructions
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
OTAPU0102SVDFXEs
Service Bulletin/Repair Instructions
Software Update 24-PU0102-SVD-FX for 2024 MY Escape vehicles is now available. Quality Improvements include: - Improved OTA deployment
SSM 52269
Service Bulletin/Repair Instructions
2022-2024 Explorer/Aviator vehicles built on or after 28-May-2022, 2022-2024 Expedition/Navigator vehicles built on or after 08-Jun-2022, 2022-2024 Escape vehicles built on or after 01-Jun-2022 and 2022 Corsair vehicles built on or after 01-Jun-2022 are no longer equipped with a hands free liftgate system. The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.
SSM 52219
Service Bulletin/Repair Instructions
Some 2023-2024 Escape vehicles built on or before 11-Jan-2024 equipped with 1.5L engines may exhibit an Engine Coolant Over-Temperature Warning message displayed in the IPC and an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern can not be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Disconnect the charge air cooler inlet and outlet hose, overflow hose, upper and lower hose of the radiator and position these components aside. Disconnect the inlet and outlet coolant hoses of the heater core and position these compone
SANVol 2 Issue 1
Service Bulletin/Repair Instructions
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This artile includes ifnormation on warranty, technical service tips and other service information.
SSM 52134
Service Bulletin/Repair Instructions
Various 2021-2024 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit a Please Check Surroundings For Safety or Full View Not Available message when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.