Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 55100
Service Bulletin/Repair Instructions
For Various Ford and Lincoln vehicles, if diagnostics lead to the replacement of the front seat cushion cover J-clips, lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901
SSM 55031
Service Bulletin/Repair Instructions
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
TSB 26-2297
Service Bulletin/Repair Instructions
Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.
SYNC-25.2.3.11.1 Escape
Over The Air
Quality improvements include: -Resolves SiriusXM disk memory usage
SSM 54939
Service Bulletin/Repair Instructions
Some 2020-2026 Corsair/Escape, 2021-2026 Bronco Sport, and 2022-2026 Maverick vehicles equipped with an 8F35 transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation. For claim
SSM 54943
Service Bulletin/Repair Instructions
Some 2025-2026 Escape vehicles equipped with an 8-inch IPC display (minor feature code HCAAN), may exhibit a fuel gauge showing the tank is filled to the 8th mark below full when the fuel tank is full. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle ID Tab > Vehicle Information, or double-clicking the vehicle identification number (VIN) in the upper left corner on Professional Technician System (PTS). To correct this condition, download and run the "IPC - Instrument Panel Cluster (IPC) Software Update" using the latest software version of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 10849 and labor operations 12651D and 12651D4.
SSM 54918
Service Bulletin/Repair Instructions
Some of the following vehicles: 2025-2026 Mustang Mach-E vehicles built on or before 27-Jan-2026 2025-2026 Maverick/Bronco Sport vehicles built on or before 20-Jan-2026 2024-2026 Nautilus vehicles built on or before 02-Dec-2025 2023-2026 Escape/Corsair may exhibit reduced steering assist and a "Power Steering Assist Fault" message displayed in the instrument panel cluster (IPC) with the diagnostic trouble code (DTC) U2016:47 only, and no other steering DTCs stored in the power steering control module (PSCM). To correct this condition, reprogram the PSCM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 3C529 and labor operations 3504E and PSCM. If a software update is not available for the PSCM, the PSCM is already at the latest software level. Refer to Workshop Manual (WSM), Section 211-02 for normal diagnostics. If the vehicle does not exhibit any observable symptoms described above and the DTC is only present in continuous memory, this DTC should be ignored. No further service action
SSM 54857
Service Bulletin/Repair Instructions
2020-2026 Explorer/Escape/Corsair, 2021-2026 Bronco Sport/Bronco, 2022-2026 Maverick, 2024-2026 Mustang/Ranger/Nautilus vehicles equipped with a 2.0L or 2.3L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 2.0L/2.3L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure been added. In addition, the wastegate actuator rod (9E408), associated retention springs (9342) and retaining clips (00817) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate actuator assembly.
SSM 54825
Service Bulletin/Repair Instructions
Some 2023-2026 Escape vehicles equipped with an 8F35 transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0767, P0766 and/or P2703 stored in the powertrain control module (PCM) and harsh/no reverse engagement. This may be due to the selectable one-way clutch (SOWC). To correct the condition, remove the transmission. Refer to Workshop Manual (WSM) > Section 307-01. Disassemble the transmission only far enough to access the SOWC. Refer to WSM, Section 307-01 > Overhaul and perform Steps 34-66. Remove the SOWC assembly, disassemble the A-clutch and discard the SOWC. Refer to WSM, Section 307-01 > Overhaul and perform Steps 164-170. Assemble the new SOWC with the A-clutch components. Refer to WSM, Section 307-01 > Overhaul and perform Steps 173-179. The A-clutch seals can be reused unless damaged. Install the new SOWC and reverse the procedure to reassemble the transmission. Overhaul the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Replace the torque converter seal. Refer to WSM, Section 307-01
SSM 54797
Service Bulletin/Repair Instructions
Some 2020-2026 Corsair/Escape, 2021-2026 Bronco Sport, and 2022-2026 Maverick vehicles equipped with an 8F35 transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation.
SSM 54741
Service Bulletin/Repair Instructions
Some 2025-2026 Escape/Maverick/Bronco Sport vehicles equipped with an 8-inch instrument panel cluster (IPC) display may exhibit a condition where the fuel gauge displays up to the 8th mark below full fuel level when the fuel tank is full. This condition does not affect vehicle durability and no additional diagnosis or service is required at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected by the end of Q3 2026. Replacement/reprogramming of the IPC will not resolve this condition. Monitor PTS for additional information and schedule service appointments for customers once the repair becomes available. If this condition is encountered, enter a vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS "Vehicle ID" screen. Fill out the GCR form, referencing this article number in the report.
ECG2-25.2.8.5 Escape
Over The Air
`Quality improvements include: -Enhanced FordPass connectivity
TCU-25.2.8.5 Escape
Over The Air
"Quality improvements include: -Addresses a loss of connectivity caused by a Cellular Domain Service outage"
TSB 26-2092
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2466 to add Bronco Sport, Escape, Maverick and Corsair, as well as removing Expedition and Navigator. One time use parts for Corsair and Bronco Sport were also added to the parts list. Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.
SSM 54615
Service Bulletin/Repair Instructions
Some 2020-2026 Escape and 2021-2026 Corsair vehicles equipped with a 2.5L engine may exhibit a fuel door that won't open with diagnostic trouble code (DTC) P04CA stored in the powertrain control module (PCM). This may be due to an open circuit on circuit SBB05 and/or a damaged splice S133. Before performing the pinpoint test for P04CA in Workshop Manual (WSM), Section 310-00, inspect circuit SBB05 and splice S133 for damage such as an open circuit. Repair as necessary. Refer to Wiring Diagram, Cell 005. If no damage is found, refer to WSM, Section 310-00 for normal diagnostics. For claiming use causal 14290 and labor operations 12650D, 12650D45, and 12650D45WR.
SSM 54601
Service Bulletin/Repair Instructions
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
SSM 54595
Service Bulletin/Repair Instructions
Some 2025 Maverick/Corsair and 2025-2026 Escape/Bronco Sport vehicles equipped with an 8F35 transmission and built on 01-Sep-2024 and through 15-Sep-2025 may exhibit a condition where the vehicle will not shift out of Park (P) and exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P07E6, P0760, P0761, P2706, P2707 and/or P2702 stored in the powertrain control module (PCM). To correct the condition, replace the main control valve body. Refer to Workshop Manual (WSM), Section 307-01. For claiming, use causal part 7A100 and labor operations 7001D and 7001D14.
SSM 54586
Service Bulletin/Repair Instructions
Some 2025-2026 Escape/Maverick/Bronco Sport vehicles equipped with an 8-inch instrument panel cluster (IPC) display may exhibit a condition where the fuel gauge displays up to the 8th mark below full fuel level when the fuel tank is full. This condition does not affect vehicle durability and no additional diagnosis or service is required at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected by the end of Q2 2026. Replacement/reprogramming of the IPC will not resolve this condition. Monitor PTS for additional information and schedule service appointments for customers once the repair becomes available. If this condition is encountered, enter a vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS "Vehicle ID" screen. Fill out the GCR form, referencing this article number in the report.
SSM 54540
Service Bulletin/Repair Instructions
Some 2025-2026 Escape/Bronco Sport vehicles equipped with a 1.5L EcoBoost engine may require replacement of the engine thermostat due to various concerns. Workshop Manual (WSM), Section 303-03A Engine Cooling > Thermostat Housing > Removal and Installation has been updated with a revised service procedure eliminating the need to remove the generator assembly to gain access to the thermostat housing.
SSM 54522
Service Bulletin/Repair Instructions
Some 2025-2026 Escape vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0073 stored in the powertrain control module (PCM) and/or B1B38 stored in the body control module (BCM). The vehicle may also exhibit no ambient air temperature reading shown in the instrument panel cluster (IPC) and/or center display screen. This may be due to a pinched, chafed, or severed wiring harness 15K867. To inspect the suspect area of the harness for damage, turn the steering wheel to the left and remove the four lower push pins from the front passenger side fender liner. Gently fold the liner inward and visually inspect the visible portion of harness 15K867 below the passenger side headlamp and follow the harness down behind the visible parts behind the front parking aid sensors.
SSM 54491
Service Bulletin/Repair Instructions
Some 2021-2026 Escape/Corsair vehicles equipped with a roof opening panel may exhibit a sunshield with localized looseness/sagging or binding/inoperative. This may be due to a broken or missing sunshield fabric retainer/clip. A revised sunshield clip (5452118) is available to address this condition. It is not necessary to replace the entire sunshield assembly if the clip(s) are broken or missing. Refer to Workshop Manual (WSM), Section 501-17 Roof Opening Panel for inspection and replacement of the roof opening panel shield clip.
TSB 25-2479
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2249 to update the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit a "Pre-Collision Assist Not Available" message in the IPC and at least one of the following conditions: Various driver assistance feature warning messages in the instrument panel cluster (IPC): - "Blind Spot System Fault" - "Cross-Traffic System Fault" - "Front Camera Fault - Service Required" Various data or lost communication diagnostic trouble codes (DTCs) stored in various modules Ford Diagnosis and Repair System (FDRS) scan tool cannot establish connectivity with the image processing module A (IPMA) during a self-test. This may be due to the software installed in the IPMA. *** MODEL SECTION **** 2023-2026 Escape equipped with minor feature code: DBCAB or DBCAA 2023-2026 Corsair equipped with minor feature code: DBCBC
SSM 54312
Service Bulletin/Repair Instructions
Some 2020-2026 Escape and 2021-2026 Corsair PHEV vehicles may require inspection of the high voltage battery due to rust, scratches, curb strikes, road debris, or other minor damage. Section 414-03A of the Workshop Manual (WSM) has recently been updated to improve diagnostics for such damage and provides a list of low-level serviceable components for instances where replacement of the high voltage battery assembly is not warranted. Refer to WSM, Section 414-03A High Voltage Battery, Mounting and Cables > Diagnosis and Testing > High Voltage Battery Minor Damage Inspection. The Ford New Vehicle Limited Warranty covers manufacturing defects resulting from a defect in factory supplied materials or workmanship. Please refer to the Warranty section WHAT IS NOT COVERED, which includes curb strikes and accidents.