Vehicle report

2015 FORD FOCUS

Compare every FORD FOCUS yearNHTSA and EPA records

Service bulletins

126 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

26L02

Other

Customer Satisfaction Program 26L02 Certain 2014-2021 Model Year Various Vehicles 1.0L Fox Classic Engine Timing Belt and Oil Pump Belt Interval Change

25H05 S1

Other

Harvest Program 25H05 – Supplement #1 Certain 2011-2021 Model Year Vehicles Software Verification Harvest Program

25N17

Other

Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation

25E05

Other

Certain 2015 - 2018 Model Year Focus Vehicles with 1.0L Engine Canister Purge Valve (CPV) Replacement (if required) and Powertrain Control Module (PCM) Reprogramming Submitting Owner Letter

SSM 54601

Service Bulletin/Repair Instructions

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

25H05

Other

This is a proactive investigation program by Ford Motor Company to inspect a limited number of affected vehicles that are customer-owned. Ford is voluntarily conducting this program to evaluate the software currently installed on one or more electronic modules in the affected vehicles.

SSM 54366

Service Bulletin/Repair Instructions

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

24N07

Other

Certain 2012 – 2018 Model Year Focus Vehicle Line One-Time Canister Purge Valve Replacement

SSM 53040

Service Bulletin/Repair Instructions

While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

SSM 52476

Service Bulletin/Repair Instructions

All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

SSM 52335

Service Bulletin/Repair Instructions

For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

14M02 S7

Service Bulletin/Repair Instructions

Certain 2011 through 2015 Model Year Fiesta and 2012 through 2016 Model Year Focus Vehicles Equipped with a DPS6 Automatic Transmission Transmission Control Module Extended Warranty Coverage REASON FOR THIS SUPPLEMENT ÃÂ¢ÃÂÃÂ¢ Due to ongoing limited part availability, program terms have been revised. ÃÂ¢ÃÂÃÂ¢ Vehicle pickup & delivery has been added. ÃÂ¢ÃÂÃÂ¢ Labor allowance table has been updated. ÃÂ¢ÃÂÃÂ¢ Additional repairs updated. ÃÂ¢ÃÂÃÂ¢ Added Attachment VI Mobile Repair/Vehicle Pickup and Delivery Record. ÃÂ¢ÃÂÃÂ¢ Added Attachment VII Mobile Repair Assessment.

SSM 51536

Service Bulletin/Repair Instructions

For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

14M02 06

Service Bulletin/Repair Instructions

Certain 2011 through 2015 Model Year Fiesta and 2012 through 2016 Model Year Focus Vehicles Equipped with a DPS6 Automatic Transmission; Transmission Control Module Extended Warranty Coverage REASON FOR THIS SUPPLEMENT Non-Ford Part Usage: Ã¢ÂÂ¢ Vehicles that are still covered by the 8 years/80,000-mile Emissions warranty coverage MUST be serviced with a NEW Ford Motor Company TCM. Ã¢ÂÂ¢ Vehicles outside of or exceeding the 8 years/80,000-mile coverage are authorized to use a used Ford Motor Company TCM, a refurbished original Ford TCM, or an aftermarket TCM that will successfully complete the required Ford software updates.

TSB 22-2309

Service Bulletin/Repair Instructions

Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.

TSB 22-2230

Service Bulletin/Repair Instructions

Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.

TSB 22-2104

Service Bulletin/Repair Instructions

This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

SSM 50258

Service Bulletin/Repair Instructions

Various 2012-2015 vehicles equipped with a 3G modem may experience a lack of 3G modem performance. This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed.

SSM 50067

Service Bulletin/Repair Instructions

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

14M02-S5

Service Bulletin/Repair Instructions

Ford is extending the warranty coverage on the DPS6 automatic transmission TCM to 10 years of service or 150,000 miles from the warranty start date of the vehicle, whichever occurs first. This extended warranty coverage will address intermittent symptoms of loss of transmission engagement while driving, no-start, or a lack of power.

TSB 21-2236

Service Bulletin/Repair Instructions

Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

SSM 49821

Service Bulletin/Repair Instructions

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

SSM 49798

Service Bulletin/Repair Instructions

2015-2018 Focus service parts transmissions part # F1FP-7000-VB / F1FZ-7000-P built on 1-Aug-2020 and through 01-Mar-2021 may have an incorrect input speed sensor A (ISSA) shim thickness. This may cause an intermittent input speed sensor diagnostic trouble code (DTC). In the event of shift issues or skip shift events, check and verify that the ISSA speed sensor shim is 2.0 mm (0.079 in) F1FZ-7Z101-A before proceeding with further diagnostics.

SSM 49210

Service Bulletin/Repair Instructions

Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.

SSM 48858

Service Bulletin/Repair Instructions

Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.

TSB 20-2171

Service Bulletin/Repair Instructions

Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

TSB 20-2140

Service Bulletin/Repair Instructions

Some 2012-2016 Focus Electric vehicles built on 15-Sep-2011 and through 9-Dec-2015 may exhibit a Stop Safely Now message displayed in the instrument panel cluster (IPC) message center. This may be due to either an internal coolant leak on the upper or lower high voltage battery or corrosion on the lower high voltage battery connector caused by water ingress. If this occurs, the vehicle may not restart once it has been shut off. To resolve the condition, follow the Service Procedure to replace the upper and lower high voltage battery or apply corrosion protection.

SSM 48619

Service Bulletin/Repair Instructions

SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.

TSB 20-2004

Service Bulletin/Repair Instructions

Some 2012-2018 Focus Electric vehicles may exhibit a Stop Safely Now message displayed in the instrument panel cluster (IPC) message center. This may be due to either an internal coolant leak on the upper or lower high voltage battery or corrosion on the lower high voltage battery connector caused by water ingress. If this occurs, the vehicle may not restart once it has been shut off. To resolve the condition, follow the Service Procedure to replace the upper and lower high voltage battery or apply corrosive protection.

SSM 48423

Service Bulletin/Repair Instructions

Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

14M02-S4

Service Bulletin/Repair Instructions

Certain 2011 through 2015 Model Year Fiesta and 2012 through 2016 Model Year Focus Vehicles Equipped with a DPS6 Automatic Transmission - Transmission Control Module Extended Warranty Coverage

19N08

Service Bulletin/Repair Instructions

Certain 2014 through 2015 Model Year Fiesta and 2014 through 2016 Model Year Focus Vehicles Equipped with a DPS6 Automatic Transmission - Transmission Clutch Shudder / Transmission Clutch Warranty Extension

SSM 48135

Service Bulletin/Repair Instructions

Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

SSM 48130

Service Bulletin/Repair Instructions

Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

SSM 48123

Service Bulletin/Repair Instructions

For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

DPS6 Dealer Com.

Service Bulletin/Repair Instructions

Short-Term DPS6 Dealer Customer Handling Direction

SSM 47976

Service Bulletin/Repair Instructions

On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

SSM 47967

Service Bulletin/Repair Instructions

Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

SSM 47850

Service Bulletin/Repair Instructions

SSM 47948

Service Bulletin/Repair Instructions

SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

SSM 47875

Service Bulletin/Repair Instructions

Some 2014-2019 Escape, 2014-2018 C-MAX, Focus, and Transit Connect vehicles not equipped with an auto start/stop system may exhibit an inability to program and/or no electrical power after installation of a service part body control module (BCM). Inspect the BCM for the presence of fuse F88. If fuse 88 is missing, install a 25 amp fuse and then re-evaluate the concern. If fuse 88 is installed in a vehicle with an auto start/stop system, the vehicle may exhibit concerns where the radio is turning off during an auto start/stop event and the instrument panel cluster (IPC) back lighting slowly goes dim during auto start/stop events.

SSM 47824

Service Bulletin/Repair Instructions

Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

SSM 47749

Service Bulletin/Repair Instructions

Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.

SSM 47710

Service Bulletin/Repair Instructions

Some 2014-2015 Escape, 2015 C-Max and Focus vehicles equipped with integrated remote start may exhibit an illuminated MIL with diagnostic trouble code (DTC) P0116 in the powertrain control module (PCM) immediately following a remote start event. Vehicles may also display a warning message stating Engine Coolant Over Temperature. This condition may occur when remote start is used and the vehicle is allowed to time out (engine shuts off). Reprogram the body control module (BCM) using the latest software version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 12A648 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

TSB 18-2373

Service Bulletin/Repair Instructions

Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2019 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the second Generation 120-volt electric vehicle service equipment (EVSE) charge cord. Follow the Service Procedure steps to correct the condition.

SSM 47703

Service Bulletin/Repair Instructions

Some 2014-2019 Escape, 2014-2018 C-MAX,Focus, and Transit Connect vehicles may exhibit a concern of not able to program and/or no electrical power after installation of a service part Body Control Module(BCM). Inspect the BCM for the presence of fuse F88. If the fuse is missing, install the correct size replacement fuse as outlined in the Wiring Manual and then re-evaluate the concern.

TSB 18-2361

Service Bulletin/Repair Instructions

Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.

TSB 18-2352

Service Bulletin/Repair Instructions

Some 2012-2018 Focus BEV vehicles may exhibit a lack of A/C. This may be due to a high-voltage battery coolant cooler (chiller) leak that may have been caused by prior transmission service. Follow the Service Procedure steps to correct the condition.

SSM 47662

Service Bulletin/Repair Instructions

For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

SSM 47638

Service Bulletin/Repair Instructions

2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.

SSM 47587

Service Bulletin/Repair Instructions

2014-2017 Fiesta, 2015-2018 Focus, 2018-2019 Ecosport vehicles equipped with a 1.0L EcoBoost engine may exhibit coolant consumption,white smoke and/or a runs rough condition. Refer to the extended coolant pressure test in Workshop Manual (WSM), Section 303-03. If no external coolant loss is confirmed, further investigation of the integrated exhaust manifold (IEM) interface is required. Carefully inspect the manifold port area for cracks. If a crack is found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01 for the repair procedures

SSM 47528

Service Bulletin/Repair Instructions

Some 2012-2018 Focus BEV vehicles may exhibit DTC U0130 in the battery electric control module (BECM) after replacement of the high voltage (HV) battery pack. In order to correct the condition, perform a programmable module installation (PMI) using the appropriate Ford scan tool. This action will initiate a coordinated flash of powertrain control module (PCM) and transmission control module (TCM) for HV battery compatibility. The use of a previous session may also cause DTC U1030 to be present in the BECM. For additional information refer to 2015 or newer Workshop Manual (WSM), Section 414-03A

SSM 47462

Service Bulletin/Repair Instructions

2015-2018 Edge, Fusion, Focus, MKZ, MKC, Escape vehicles equipped with a 2.0L EcoBoost engine may exhibit coolant consumption, white smoke and/or a runs rough condition. Refer to the extended coolant pressure test and checking for combustion gases in Workshop Manual (WSM), Section 303-03A. If internal coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect the cylinder block and head for erosion, pitting, and flatness defects, primarily between the cylinder to cylinder bore bridges. If defects to the aluminum surface on the cylinder block and/or cylinder head are found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01A for the repair procedures

SSM 47201

Service Bulletin/Repair Instructions

Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.

SSM 47198

Service Bulletin/Repair Instructions

Some 2013-2017 Fusion Energi, 2012-2017 Focus Electric and 2013-2017 C-MAX Energi vehicles equipped with a TCU built on or before 11-Oct-2017 may exhibit a discharged battery, inoperative remote features via MyFord Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If U0198 DTC still remains, remove the TCU fuse for 5 minutes then reinstall. Reprogram the TCU using IDS or Ford J2534 Diagnostic Software (FJDS) release 108.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual

TSB18-2093

Service Bulletin/Repair Instructions

Some 2015-2018 Focus ST vehicles may exhibit a misfire condition and/or illuminated MIL with DTCs P0300 and/or P0316 with engine coolant temperature below 49°C (120°F). Follow the Service Procedure steps to correct the condition.

SSM 47161

Service Bulletin/Repair Instructions

Some 2012-2017 Focus BEV, 2013-2016 Fusion Energi And 2013-2017 CMAX Energi vehicles equipped with a Telematics Control Unit (TCU) may exhibit inoperative remote features via My Ford Mobile app, discharged battery, incomplete user authorization and/or diagnostic trouble code (DTC) U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If DTC U0198 remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Perform IDS Network Test and reprogram the TCU using Integrated Diagnostic System (IDS) release 108.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.

SSM 47130

Service Bulletin/Repair Instructions

Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2018 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the Delphi 120 volt electric vehicle service equipment (EVSE) charge cord. To identify a Delphi EVSE the coupler on the EVSE that connects to the vehicle charge port is solid black. For information on the Delphi EVSE indicator status used for diagnostics, reference High Voltage Battery > Charging the High Voltage Battery in the Owners Guide for a 2018 Fusion Energi. Reference the Convenience Cord Light Emitting Diode (LED) Indicators chart. The Workshop Manual (WSM) is scheduled to be revised at a later date.

SSM 47080

Service Bulletin/Repair Instructions

2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.

TSB18-2009

Service Bulletin/Repair Instructions

Some 2013-2016 Focus Electric vehicles built on or after 22-Feb-2013 may exhibit an illuminated green ready to drive indicator in the instrument panel cluster (IPC) and the vehicle does not move. The condition may occur when the vehicle is restarted within 20 seconds after being powered off, starting the vehicle within 20 seconds of unplugging or starting the vehicle 15 minutes after being remotely started. Follow the Service Procedure steps to correct the condition.

SSM 47009

Service Bulletin/Repair Instructions

The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

SSM 46907

Service Bulletin/Repair Instructions

Some 2015-2018 Focus ST vehicles may exhibit MIL On with DTC's P0300 and/or P0316 store in Powertrain Control Module(PCM) memory. Vehicle may also exhibit perceived misfire after cold start until Engine Coolant Temperature(ECT) reaches 49 degrees C (120 degrees F) Install (4) new CYFS-12-YEC spark plugs and set plug gap to 1.0mm(0.040). Use ROTUNDA RTTP tool KDT165 or equivalent to gap and adjust the plugs before installing. For Drivability concerns Refer to Powertrain Control/Emissions Diagnosis (PC/ED) manual. Engineering is currently investigating this concern. To assist with the investigation use the Report A Vehicle Concern link at the bottom of the Oasis report and submit a Global Concern Report (GCR). Continue to monitor OASIS for updates.

17-2218

Service Bulletin/Repair Instructions

Some 2013-2018 Escape, Focus and C-Max vehicles may exhibit a water stained headliner after the vehicle has experienced a water leak from areas such as the roof opening panel, fixed glass, roof rails and roof ditch mouldings. Follow the procedure below to remove the water stains from the headliner after the water leak has been repaired. Follow the Service Procedure steps to correct the condition.

SSM 46900

Service Bulletin/Repair Instructions

Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

SSM 46850

Service Bulletin/Repair Instructions

Some 2015-2017 Focus vehicles equipped with a dual clutch power-shift transmission may exhibit excessive engine vibration. This may be due to a binding condition with the powertrain mounts. Before replacing components, Perform the powertrain mount neutralization procedure. Refer to Workshop Manual (WSM), Section 303-00.

SSM 46814

Service Bulletin/Repair Instructions

Some 2014-2017 Focus ST vehicles equipped with a 2.0L gasoline turbocharged direct injection (GTDI) engine may exhibit an audible engine idle ticking noise at normal operating temperature. This is considered a normal operating characteristic and no repair should be attempted.

SSM 46545

Service Bulletin/Repair Instructions

Some 2014-2017 Focus/C-MAX vehicles when a replacement BCM is received for a service repair may include a white Keyless Entry Card. In an effort to consolidate the complexity of BCM's only the highest level will be available for service. If the vehicle has the Keyless Entry buttons on the left door B-pillar the card needs to stay with the vehicle and shared with the customer as the keyless entry codes have changed. If the vehicle was not built with the b-pillar touch pad, discard the card, as it has no function, and cannot be added to the vehicle. If the vehicle has the stick-on wireless key pad, that keypad has it's own card, and again discard the one that came with the service BCM.

SSM 46539

Service Bulletin/Repair Instructions

Some 2015-2017 Focus ST vehicles may exhibit MIL On with a perceived Misfire after cold start. Diagnostic Trouble Codes DTC's) may include P0300, P0301, P0302, P0303,P0304, and P0316. Refer to General Service Bulletin GSB) G0000106 to confirm Historical DTCs no longer confirmed or pending, but have set at least once since the last time DTCs were cleared. Refer to Workshop Manual (WSM) Section, 303-01 and Powertrain Control/Emissions Diagnosis (PC/ED) manual for normal diagnostics. To assist with the investigation use the Report A Vehicle Concern link at the bottom of the OASIS report and submit a Global Concern Report (GCR). Engineering is currently investigating this concern. Continue to monitor OASIS for updates.

SSM 46534

Service Bulletin/Repair Instructions

Some 2013-2017 Fusion Hybrid Energi built on or before 24-Mar-2017, 2012-2016 Focus Electric and 2013-2016 C-MAX Energi and equipped with a TCU may exhibit inoperative remote features via MyFord Mobile app, discharged battery, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct, perform any open TCU field service actions (FSAs). If U0198 DTC remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Reprogram the TCU using Integrated Diagnostic System (IDS) release 104.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.

SSM 46421

Service Bulletin/Repair Instructions

2013-2017 FOCUS S MODEL VEHICLES DO NOT HAVE AN OUTSIDE AMBIENT TEMPERATURE DISPLAYED IN THE IPC AND THIS FEATURE CANNOT BE ADDED. THE SENSOR IS IN THE RIGHT HAND OUTSIDE MIRROR AND IS USED BY THE POWERTRAIN CONTROL MODULE (PCM) FOR CALCULATIONS.

14M02-S3

Service Bulletin/Repair Instructions

CERTAIN 2011 THROUGH 2015 MODEL YEAR FIESTA AND 2012 THROUGH 2016 MODEL YEAR FOCUS VEHICLES EQUIPPED WITH A DPS6 AUTOMATIC TRANSMISSION - TRANSMISSION CONTROL MODULE EXTENDED WARRANTY COVERAGE

SSM 46358

Service Bulletin/Repair Instructions

2011-2017 FIESTA AND 2012-2017 FOCUS SERVICE PIGTAIL FOR TRANSMISSION CONTROL MODULE CONNECTOR C1750A IS AVAILABLE. IF REPAIRS ARE NEEDED USE PART NUMBER FU2Z-14S411-VA. REPLACEMENT OF WIRING HARNESS 12A581 IS NO LONGER REQUIRED WHEN THIS CONNECTOR NEEDS SERVICING.

SSM 46355

Service Bulletin/Repair Instructions

MULTIPLE 2014-2016 VEHICLES EQUIPPED WITH 6F35 TRANSMISSION AND BUILT ON 1-JAN-2014 AND THROUGH 31-DEC-2015 MAY EXHIBIT HARSH REVERSE ENGAGEMENT AND HARSH/DELAYED 3RD AND 5TH GEAR UP/DOWN SHIFTS WITH NO DTCS PRESENT. THIS MAY BE DUE TO A MECHANICALLY BINDING SHIFT SOLENOID B (SSB). VERIFY HARSH REVERSE AND 3RD AND 5TH GEAR SHIFT EVENTS ARE PRESENT. USING IDS, IDENTIFY THE BAND NUMBER OF SSB FOR USE WHEN ORDERING PARTS. REMOVE THE MAIN CONTROL. DISASSEMBLE AND THOROUGHLY CLEAN THE VALVE BODY AND SOLENOID BODY TO REMOVE ANY CONTAMINANTS. REPLACE SSB, REFER TO WORKSHOP MANUAL (WSM) SECTION 307-01. USING IDS, CLEAR TRANSMISSION ADAPTIVE TABLES. FOR CLAIMING, USE CAUSAL PART 7G383 AND APPLICABLE LABOR OPERATIONS IN SECTION 7 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

SSM 46339

Service Bulletin/Repair Instructions

SOME 2015-2017 FOCUS VEHICLES EQUIPPED WITH REMOTE START (FACTORY OR DEALER INSTALLED) MAY EXHIBIT A CLIMATE CONTROL SYSTEM THAT DOES NOT RESPOND CORRECTLY TO A REMOTE START EVENT. THIS MAY BE DUE TO THE BODY CONTROL MODULE (BCM) CONFIGURATIONS/SETTINGS. THIS MAY AFFECT HEATED SEATS, HEATED STEERING WHEEL, HEATED BACKGLASS, AND/OR FRONT DEFROSTER. VERIFY THE BCM IS AT THE LATEST LEVEL. THE ISSUE IS CURRENTLY UNDER ENGINEERING INVESTIGATION, DO NOT ATTEMPT ANY ADDITIONAL REPAIRS AT THIS TIME. MONITOR OASIS FOR FUTURE UPDATES.

SSM 46332

Service Bulletin/Repair Instructions

REPLACING THE ORIGINAL EQUIPMENT SYNC/NAVIGATION SYSTEM WITH EITHER AN AFTERMARKET SYNC/NAVIGATION KIT OR MODIFYING ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.

SSM 46322

Service Bulletin/Repair Instructions

SOME 2015-2016 FOCUS VEHICLES IF EQUIPPED WITH REMOTE START AND BUILT ON OR BEFORE 17-OCT-2016 MAY EXHIBIT VEHICLE STALL WITH A MALFUNCTION INDICATOR LAMP (MIL) AND DIAGNOSTIC TROUBLE CODE (DTC)P1594. THIS MAY BE DUE TO WHEEL SPEED SENSOR REPORTING MOVEMENT OF THE VEHICLE WHILE STOPPED. TO CORRECT THIS CONDITION, UPDATE THE BODY CONTROL MODULE (BCM) TO THE LATEST CALIBRATION LEVEL USING INTEGRATED DIAGNOSTIC SOFTWARE (IDS) VERSION 103.03 OR HIGHER. REFER TO WORKSHOP MANUAL (WSM) SECTION 419 TO PERFORM THE BCM UPDATING PROCEDURE. MAKE SURE THE IDS IS CONNECTED TO THE INTERNET WHEN ENTERING MODULE REPROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM USE CAUSAL PART 14A068 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SLTS MANUAL.

SSM 46303

Service Bulletin/Repair Instructions

THE 2012-2017 FOCUS WORKSHOP MANUAL (WSM) PROCEDURE FOR OIL PAN AND REAR MAIN OIL SEAL INSTALLATION HAS BEEN REVISED. REFER TO WSM, SECTION 303-01 REMOVAL AND INSTALLATION. THE SEALANT APPLICATION LOCATION HAS BEEN REVISED. SPECIAL ATTENTION SHOULD BE USED AT T-JOINT LOCATIONS FOR CLEANLINESS AND SEALANT APPLICATION.

SSM 46298

Service Bulletin/Repair Instructions

THE EV RANGE AFTER FULLY CHARGING A 2012-2016 FOCUS ELECTRIC, 2013-2016 C-MAX/FUSION ENERGI MAY VARY AFTER EACH CHARGING EVENT. THE WINDOW STICKER INDICATES 0-19 MILE RANGE FOR 2013-2016 CMAX/FUSION ENERGI. VARIATION OF EV RANGE MAY NOT INDICATE A BATTERY OR CHARGING CONCERN. EV RANGE IS SIMILAR TO THE DTE DISPLAY ON GASOLINE VEHICLES, EV RANGE WILL VARY WITH DRIVING/OPERATING CONDITIONS. CONDITIONS INCLUDE: EXTREME OUTSIDE TEMPERATURES, TERRAIN, DRIVING STYLE, CITY OR HIGHWAY DRIVING, TIRE PRESSURE, AND USE OF ACCESSORIES. IF THE CUSTOMER REPLACES THE LOW ROLL RESISTANCE TIRES WITH A MORE AGGRESSIVE TREAD THE RANGE WILL SUFFER. USING THE CABIN HEATER AND A/C, WHICH ARE ELECTRIC, WILL ALSO DECREASE EV RANGE. TO TEMPORARILY REMOVE THE IMPACT OF DRIVING/CLIMATE HISTORY, RESET THE LIFETIME SUMMARY OR DRIVING HISTORY BY USING THE SETTINGS MENU ON THE LEFT SIDE OF THE INSTRUMENT CLUSTER, UNDER DISPLAY

SSM 46295

Service Bulletin/Repair Instructions

TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

SSM 46282

Service Bulletin/Repair Instructions

SOME 2014-2017 FIESTA AND 2015-2017 FOCUS VEHICLES WITH THE 1.0L GTDI ENGINE MAY EXHIBIT A TURBOCHARGER WASTEGATE ROD RATTLE. THIS MAY BE DUE TO THE WASTEGATE LINKAGE. THIS NOISE IS CONSIDERED NORMAL AND IS NOT A SIGN OF A DEFECTIVE TURBOCHARGER. THE WASTEGATE ROD HAS CLEARANCES BUILT INTO THE CONTROL LINKAGE TO ACCOMMODATE THERMAL EXPANSION. THE TURBOCHARGER SHOULD NOT BE REPLACED FOR THIS CONDITION.

SSM 46210

Service Bulletin/Repair Instructions

SOME 2010-2016 EPAS EQUIPPED VEHICLES MAY EXHIBIT STEERING RELATED NOISES. THE WORKSHOP MANUAL (WSM) DIAGNOSTIC PROCEDURES HAVE BEEN UPDATED IN SECTION 211-02. WHEN DIAGNOSING AND REPAIRING EPAS STEERING NOISES USE THE UPDATED PROCEDURES.

SSM 46207

Service Bulletin/Repair Instructions

SOME 2013-2017 FOCUS 4-DOOR SEDANS HAVE A SINGLE DAMPENER ON THE LEFT HAND SIDE, ADJACENT TO THE LIFTING COIL SPRING, TO SLOW THE OPERATION OF THE LUGGAGE COMPARTMENT DECK LID WHEN OPENING AND CLOSING. THE LUGGAGE COMPARTMENT DECK LID IS HELD OPEN ONLY BY THE COIL SPRINGS CONNECTED TO THE HINGES. THE DAMPENER IS NOT CHARGED WITH GAS TO SUPPORT THE LUGGAGE COMPARTMENT LID LIKE THE 5 DOOR HATCHBACK LIFT CYLINDERS. REFER TO THE UPDATED WORKSHOP MANUAL SECTION 501-03 FOR ADDITIONAL INFORMATION. IT IS NORMAL FOR THE DAMPENER TO COMPRESS EASILY WHEN REMOVED FROM THE VEHICLE, UNLIKE THE HATCHBACK LIFT SUPPORT CYLINDERS.

SSM 46197

Service Bulletin/Repair Instructions

SOME 2013-2017 FOCUS/C-MAX VEHICLES EXHIBIT A FRAYED/CUT SHORT APPEARANCE AT THE FRONT EDGE OF THE HEADLINER NEAR THE WINDSHIELD. THIS IS A NORMAL CHARACTERISTIC OF THE HEADLINER AND NO REPAIRS SHOULD BE ATTEMPTED. ON 5 DOOR FOCUS(HATCHBACK) THE EXPOSED EDGE AT THE REAR LIFT GATE AREA MAY BE DUE THE HEM LIP OUT OF POSITION (BENT) PULLING THE WEATHER STRIP OUT OF POSITION, EXPOSING THE EDGE. THE HEM LIP CAN EASILY BE REPOSITIONED AND WILL KEEP THE HEADLINER EDGE COVERED BY THE WEATHER-STRIP, WITHOUT HEADLINER REPLACEMENT.

SSM 46153

Service Bulletin/Repair Instructions

SETTING THE CORRECT TIRE INFLATION PRESSURE IS AN IMPORTANT STEP IN THE PRE-DELIVERY PROCESS AND DURING ROUTINE MAINTENANCE INTERVALS. RECENT CUSTOMER CLINICS REVEALED THAT MOST EVERY VEHICLE IN THE CLINICS HAD THE TIRE PRESSURES SET INCORRECTLY. TIRE PRESSURES FROM THE FACTORY ARE NOT SET TO THE CORRECT SPECIFICATION. MAINTAINING THE CORRECT TIRE PRESSURE IS KEY TO THE RIDE CHARACTERISTICS OF THE VEHICLE AND AFFECTS RIDE QUALITY, HANDLING, LOAD CAPACITY AND TIRE WEAR. THE RECOMMENDED PRESSURE SETTINGS CAN BE FOUND ON THE TIRE INFORMATION LABEL IN THE DRIVER'S SIDE FRONT DOOR JAM. DO NOT USE THE TIRE PRESSURES LISTED ON THE SIDEWALL OF THE TIRES. MAINTAINING THE TIRE PRESSURE IS PART OF NORMAL MAINTENANCE. IT SHOULD BE RECHECKED MONTHLY, PER THE OWNER GUIDE AND DURING THE RECOMMENDED TIRE ROTATION INTERVALS.

SSM 46132

Service Bulletin/Repair Instructions

SOME 2008-2017 FORD/MERCURY/LINCOLN VEHICLES EQUIPPED WITH SYNC MAY GENERATE A VHR THAT IDENTIFIES A CONCERN WITH THE BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

SSM 46102

Service Bulletin/Repair Instructions

Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.

TSB 16-0129

Service Bulletin/Repair Instructions

Some 2011-2016 Fiesta and 2012-2016 Focus vehicles equipped with a DPS6 transmission may exhibit intermittent concerns of loss of transmission engagement while driving, intermittent no start or a loss of power. These symptoms are usually accompanied by an illuminated Check Engine lamp. Additional symptoms may include messages in the message center indicating hill start assist is not available, that parking aid malfunction/service is required or the transmission PRNDL/S gear selector on the instrument cluster may flash. Diagnostic trouble codes (DTCs) U0100, U0101, U1013 and/or P0606 will be present or stored in the powertrain control module (PCM) memory. Follow the Service Procedure steps to correct the condition.

SSM 46085

Service Bulletin/Repair Instructions

The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

SSM 46013

Service Bulletin/Repair Instructions

SOME 2014-2015 FOCUS AND FIESTA VEHICLES EQUIPPED WITH A 1.0L GTDI BUILT ON OR BEFORE 07/25/2015 MAY EXHIBIT LACK OF POWER AND MULTIPLE MISS FIRE DIAGNOSTIC TROUBLE CODES (DTC). IF NORMAL ENGINE DIAGNOSIS LEADS TO LOW COMPRESSION AND PISTON DAMAGE, INSPECT THE EXHAUST VALVES FOR A PIN HOLE IN THE CENTER OF THE VALVE HEAD.

SSM 46011

Service Bulletin/Repair Instructions

SOME 2015-2017 FOCUS/C-MAX/ESCAPE VEHICLES EQUIPPED WITH ONE TOUCH UP FEATURE. THE 2016-2017 WORKSHOP MANUAL SECTION 501-11 WAS UPDATED 8/2016 WITH REVISED DIAGNOSTICS, THE 2015 WSM UPDATES WILL FOLLOW LATER. REFER TO THE 2016-2017 WSM REVISED DIAGNOSTICS FOR ANY OF THE FOLLOWING CONCERNS: ONE-TOUCH UP FEATURE IS INOPERATIVE, WINDOW DOOR GLASS DOES NOT TRAVEL FULLY TO EITHER OPEN/CLOSED POSITION,AND WINDOW BOUNCES BACK CONCERNS. AT THE BEGINNING OF PINPOINT TEST E, CARRY OUT THE INITIALIZATION PROCEDURE ON THE SUSPECT POWER WINDOW, BEFORE CONTINUING THE PINPOINT TEST. REFER TO: POWER DOOR WINDOW INITIALIZATION - VEHICLES WITH: ONE-TOUCH OPEN AND CLOSE FRONT WINDOWS (501-11 GLASS, FRAMES AND MECHANISMS, GENERAL PROCEDURES).

TSB16-0109

Service Bulletin/Repair Instructions

SOME 2011-2015 FIESTA VEHICLES BUILT ON OR BEFORE 10/15/2014 AND 2012-2016 FOCUS VEHICLES EQUIPPED WITH A DPS6 AUTOMATIC TRANSMISSION MAY EXHIBIT EXCESSIVE TRANSMISSION CLUTCH SHUDDER ON LIGHT ACCELERATION. SOME VEHICLES MAY OR MAY NOT EXHIBIT TRANSMISSION FLUID LEAKING FROM THE CLUTCH HOUSING. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

SSM 45963

Service Bulletin/Repair Instructions

SOME 2015-2016 FOCUS VEHICLES BUILT ON OR BEFORE 11/18/2015 MAY EXHIBIT AN INCORRECT AVERAGE FUEL ECONOMY READING. FOCUS CLUSTERS HAVE TWO TRIP COMPUTERS (TRIP 1 AND TRIP 2). IF THE CUSTOMER IS USING ONE FOR SHORT TRIPS (RESET AT EVERY REFILL) AND THE OTHER FOR LONG TRIPS (NO RESET SINCE HE/SHE OWNS THE VEHICLE) THE ISSUE MAY BE PRESENT AFTER EITHER TRIP COMPUTER READS GREATER THAN 3219 KM (2000 MILES). REPROGRAM THE INSTRUMENT PANEL CLUSTER (IPC) TO RESOLVE THE CONCERN, USING IDS VERSION 98.01 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE APPLICABLE 12651D LABOR OPERATIONS IN SECTION 10 OF THE SLTS MANUAL, USE CAUSAL PART 10849 FOR REPROGRAM.

SSM 45941

Service Bulletin/Repair Instructions

2011-2016 FIESTA AND 2012-2016 FOCUS WITH DPS6 TRANSMISSION HAVE A NEW CLUTCH AVAILABLE. THIS CHANGE AFFECTS TCM/PCM CALIBRATIONS. 2011-2013 FIESTA CALIBRATIONS HAVE NOT YET BEEN RELEASED, CONTINUE TO SERVICE WITH BV6Z-7B546-F CLUTCH, PERFORM ANY REPROGRAMMING WITH IDS RELEASE 101.01 ONLY. 2014-2016 FIESTA VEHICLES CONTINUE TO USE FA6Z-7B546-A CLUTCH AND ARE NOT AFFECTED BY CALIBRATION. 2012-2016 FOCUS CAN USE CLUTCH F1FZ-7B546-B FOLLOWING TSB 15-0120 AND FSA 14M01 AND CALIBRATIONS RELEASED WITH IDS 101.02. WORKSHOP MANUALS HAVE BEEN UPDATED TO INCLUDE A REPAIR VALIDATION CODE (RVC) IN DIAGNOSIS BY SYMPTOM, PINPOINT TEST A (FOCUS, 2014-15 FIESTA), PINPOINT TEST N (2011-2013 FIESTA). RVC CODE IS NOT REQUIRED ON WARRANTY CLAIMS AT THIS TIME. ALL PUBLICATIONS WILL UPDATE SOON, WHEN 2011-2013 FIESTA CALIBRATION IS RELEASED.

SSM 45923

Service Bulletin/Repair Instructions

2013-2016 FOCUS S MODEL VEHICLES DO NOT HAVE AN OUTSIDE AMBIENT TEMPERATURE DISPLAYED IN THE IPC AND THIS FEATURE CANNOT BE ADDED. THE SENSOR IS IN THE RIGHT HAND OUTSIDE MIRROR AND IS USED BY THE POWERTRAIN CONTROL MODULE (PCM) FOR CALCULATIONS.

SSM 45898

Service Bulletin/Repair Instructions

2012-2016 FOCUS SEDAN LUGGAGE COMPARTMENT LID WON'T STAY UP

14M02-S2

Service Bulletin/Repair Instructions

CERTAIN 2011 THROUGH 2015 MODEL YEAR FIESTA AND 2012 THROUGH 2015 MODEL YEAR FOCUS VEHICLES EQUIPPED WITH A DPS6 AUTOMATIC TRANSMISSION - TRANSMISSION CONTROL MODULE EXTENDED WARRANTY COVERAGE

SSM-45855

Service Bulletin/Repair Instructions

AVERAGE FUEL ECONOMY LOW AND/OR INCORRECT - BUILT ON OR BEFORE 11/18/2015

SSM-45856

Service Bulletin/Repair Instructions

MAY ILLUMINATE THE MALFUNCTION INDICATOR LAMP (MIL) WITH MISFIRE CODES

SSM-45821

Service Bulletin/Repair Instructions

SIRI EYES FREE FUNCTIONAL ISSUES USING BLUETOOTH AND APPLE IOS 9.2 AND 9.2.1

SSM-45815

Service Bulletin/Repair Instructions

AIR CONDITIONING (A/C) INOPERATIVE - DIAGNOSTIC TROUBLE CODE (DTC) P0645

16-0062

Service Bulletin/Repair Instructions

Some 2012-2015 Focus vehicles may exhibit inaccurate fuel gauge indication and/or inaccurate distance to empty. The vehicle may also exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0420, P1450, P0443, P0452, P0456, P0460 and/or P2196.

16B10

Service Bulletin/Repair Instructions

In some of the affected vehicles, the front control/display interface module (FCDIM) may have been unintentionally programmed for the European market instead of the North American market

16-0055

Service Bulletin/Repair Instructions

1.0L ECOBOOST - ILLUMINATED MIL - DTC P1450 - BUILT ON OR BEFORE 10/19/2015 ISSUE Some 2015-2016 Focus vehicles equipped with an 1.0L EcoBoost engine and built on or before 10/19/2015 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P1450 (unable to bleed up fuel tank vacuum) present in powertrain control module (PCM) memory. ACTION Reprogram the powertrain control module (PCM) to the latest calibration using IDS release 99.05 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.

16-0044

Service Bulletin/Repair Instructions

DPS6 - NO START AND/OR TRANSMISSION ENGAGEMENT OR LOSS OF POWER WITH DTCS U0100, U0101, U1013, U3003 AND/OR P0606 ISSUE Some 2011-2016 Fiesta and 2012-2016 Focus vehicles equipped with a DPS6 transmission may exhibit intermittent concerns of loss of transmission engagement while driving, intermittent no start or a loss of power. These symptoms are usually accompanied by an illuminated Check Engine lamp. Additional symptoms may include messages in the message center indicating hill start assist is not available, that parking aid malfunction/service is required or the transmission PRNDL/S gear selector on the instrument cluster may flash. Diagnostic trouble codes (DTCs) U0100, U0101, U1013, U3003 and/or P0606 will be present or stored in the powertrain control module (PCM) memory.

TSB160044

Service Bulletin/Repair Instructions

DPS6 - no satart and/or transmission engagement or loss of power with DTCS u0100, U00101, U1013, U3003 AND/OR P0606

TSB 16-0147

Service Bulletin/Repair Instructions

SOME 2013-2016 FOCUS ELECTRIC VEHICLES BUILT ON OR AFTER 22-FEB-2013 MAY EXHIBIT AN ILLUMINATED GREEN READY TO DRIVE INDICATOR IN THE INSTRUMENT PANEL CLUSTER (IPC) AND THE VEHICLE DOES NOT MOVE. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

TSB160055

Service Bulletin/Repair Instructions

1.0L Ecoboost - kIlluminated MIL - DTC P1450 - Built on or before 10/19/2015

CSP-15-B-31

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

TSB-15-0134

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

CSP-15B-22

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

SB-14M02-SUP2

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

TSB-15-0120

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

TSB-15-0121

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

TSB15-0120

Service Bulletin/Repair Instructions

FORD: 2012-2015 FOCUS AND 2011-2015 FIESTA MAY EXHIBIT TRANSMISSION FLUID LEAKAGE AND EXCESSIVE TRANSMISSION CLUTCH SHUDDER ON LIGHT ACCELERATION ON VEHICLES THAT HAVE A DPS6 AUTOMATIC TRANSMISSION *CN

TSB15-0121

Service Bulletin/Repair Instructions

FORD: 2011-2015 FIESTA AND 2012-2015 FOCUS MAY SHOW CONCERNS OF LOSS OF TRANSMISSION ENGAGEMENT WHILE DRIVING OR LOSS OF POWER *CN

44863

Service Bulletin/Repair Instructions

FORD: NO SERVICE ACTION IS RECOMMENDED FOR THIS CONDITION. PLEASE USE AT YOUR DISCRETION. VARIOUS 2010-2015 VEHICLES MAY EXPERIENCE A TURBULENCE NOISE, SIMILAR TO AN HELICOPTER NOISE, AT HIGHWAY SPEEDS WHEN THE REAR DOOR WINDOW(S) OR SUNROOF ARE OPEN. *TA

SFA-15L02

Service Bulletin/Repair Instructions

FORD/LINCOLN: TSB CONTAINS AN OWNER NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. IF VEHICLE OPERATES MORE THAN 100 MPH THAN TIRE PRESSURE LABEL INDICATES, THAN TIRE PRESSURE SHOULD BE INCREASED BY THREE (3) PSI THAT IS LISTED IN SAFETY COMPLIANCE CERTIFICATION AND TIRE LABEL. MODEL 2015 FOCUS ST. *PE

ASI-45156

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

ASI-45166

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

ASI-45178

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

44977

Service Bulletin/Repair Instructions

FORD 2014 FUSION, 2014-2015 MKZ : SERVICE BULLETIN INFORMATION REGARDING VEHICLES ACTIVE PARK ASSIST FINISHES TOO EARLY BUILT ON 01/17/2015. *LJ

TSB160062

Service Bulletin/Repair Instructions

Inaccurate fuel gauge or distance to empty indication - built on or before 01/21/2015

TSB 14-0216

Service Bulletin/Repair Instructions

FORD: SOME 2014-2015 FORD FOCUS MAY EXPERIENCE A HARD START, LONG CRANK, OR RUNS ROUGH CONDITION IF EQUIPPED WITH GTDI ENGINES. *TA.

ASI-44707

Service Bulletin/Repair Instructions

FORD: AFTER POWERTRAIN CONTROL MODULE REPROGRAMMING, THE MALFUNCTION INDICATOR LAMP (MIL) IS ON WITH SEVERAL DIAGNOSTIC TROUBLE CODES (DTC) P06B8, P068A, P2610, IF KEY NOT LEFT FOR 30 SECONDS IN OFF POSITION FOLLOWING PROGRAMMING ON SOME MODEL 2009-15 VEHICLES. *PE

ASI-44732

Service Bulletin/Repair Instructions

FORD: THE CLUTCH ASSEMBLY SHOULD NOT BE REPLACED ON DPS6 TRANSMISSION IF NOT COMPLETED 1000 MILES (1600K) THAT IS REQUIRED FOR BREAKING IN DUAL CLUTCH FRICTION MATERIAL. MODEL 2014-15 FOCUS, FIESTA. *PE

ASI-44649

Service Bulletin/Repair Instructions

FORD: A JOB AID WAS DEVELOPED AND NOW AVAILABLE FOR THE PTU INTERNAL OR EXTERNAL FLUID LEAKAGE FOR ALL WHEEL DRIVE VEHICLES. *PE

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.