Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 55118
Service Bulletin/Repair Instructions
Some of the following vehicles: * 2023-2025 F-Super Duty built on or before 02-Feb-2025 * 2024-2026 Ranger/Bronco/Mustang * 2024-2025 F-150 built on or before 15-Jul-2025 * 2024-2025 Nautilus built on or before 16-Feb-2025 * 2025 Explorer/Aviator built on or before 01-Feb-2025 may exhibit all of the following symptoms: - "No Key Detected" message displayed on the instrument panel cluster (IPC). - Key fob does not work in the backup slot. - Remote keyless entry (RKE) (lock and unlock from the key fob) functionality will work to lock/unlock the vehicle. If the vehicle exhibits these symptoms, start the vehicle using both key fobs. If the no crank/no start condition with "No Key Detected" concern is present, reprogram both key fobs and retest. If the no crank/no start condition with "No Key Detected" is still present, replace the body control module (BCM). Refer to Workshop Manual (WSM), Section 419-10. For claiming, use causal part 15604 and labor operation MT55118SSM up to 1.8 hours.
SSM 55072
Service Bulletin/Repair Instructions
Some 2025-2026 Mustang vehicles equipped with a 5.0L or 2.3L engine and built on 15-Aug-2025 and through 01-Dec-2025 may exhibit various drivability symptoms and/or have diagnostic trouble codes (DTC) stored in the powertrain control module (PCM) related to throttle/pedal position circuits. This may be caused by a spread terminal at the PCM connector. Inspect for loose fitting terminals at C1551B for 2.3L vehicles, and C175B on 5.0L vehicles. Refer to the appropriate Wiring Diagram Cells for circuit identification and wiring repair information. Wire terminal repair kit part DU2Z-14474-CA is recommended for this repair. Refer to Wiring Diagram, Cell 005 for repair procedures. For claiming, use causal part 14290 and labor operations 12651D, 12651D45 and 12651D45WR.
SSM 55061
Service Bulletin/Repair Instructions
Some 2024-2026 Mustang vehicles built on or before 23-Apr-2026 may exhibit a sagging headliner appearance at the door openings which show the raw headliner edge untucked from the door glass run. An updated door glass run has been released for service (Left Side:PR3Z-6321597-B, Right side:PR3Z-6321596-B). Refer to Workshop Manual, Section 501-05.
SSM 55031
Service Bulletin/Repair Instructions
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
SSM 55008
Service Bulletin/Repair Instructions
Some 2021-2026 Ford vehicles may exhibit inoperative heated/cooled seats, heated steering wheel and/or front/rear defrost features after a remote start is performed through the Ford mobile application or with the key fob. Customers may also experience heated/cooled seats, heated steering wheel and/or front/rear defrost features turning on in unexpected conditions such as during warmer weather. These features will operate normally when commanded in the center display screen. This may be due to the customer not setting up their "Climate Settings" through the Ford mobile application. To correct this condition, inform the customer they should perform a remote start from the Ford mobile application and then adjust the "Climate Settings" in the Ford mobile application as desired. These settings only need to be set once and will persist through subsequent remote starts. Heated and cooled seats will be set to Level 2 when turned ON via "Climate Settings" in the Ford mobile application during a remote start event. This is normal operating characteristic. This condition does not affect vehicle durability and no a
26E04
Emissions
NEW VEHICLE DELIVERY HOLD - Emissions Recall 26E04 Certain 2021-2025 Model Year F-150, Maverick, Mustang, Ranger, Expedition, Bronco Sport, Explorer, Bronco, Navigator, and Aviator Vehicles Powertrain Control Module Software Update
TSB 26-2297
Service Bulletin/Repair Instructions
Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.
SSM 54912
Service Bulletin/Repair Instructions
Some 2025-2026 Mustang vehicles built on 01-Jun-2025 and through 25-Apr-2026 may exhibit a chirp and/or rattle noise from the left side of the instrument panel. This may be due to the heating, ventilation and air condition (HVAC) control module lower fastener making contact with the instrument panel frame directly behind the fastener. To correct the condition, remove the HVAC control module. Refer to Workshop Manual (WSM), Section 412-00 > General Information > Removal and Installation > Heating, Ventilation and Air Conditioning (HVAC) Control Module. Installing the lower fastener without the module will show where it is making contact with the instrument panel frame. If contact is present, use flock tape (Rotunda part number 164-R4903) to insulate the instrument panel frame from the end of the lower fastener. Reinstall the HVAC module. For claiming, use causal part 19980 and labor operations 19700D and 19700D16.
TSB 26-2263
Service Bulletin/Repair Instructions
This bulletin supersedes 26-2112. Reason For Update: add 2026 model year vehicles, update LV fluid XT-10-QLVC and CXT-10-LV6 description to add "Transfer Case Fluid 4WD Only", and update Step 4 to inspect/replace 7H351 and 7B177 outside of this article. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated MIL with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
TSB 26-2210
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Engine misfire condition * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0301, P0302, P0303, and/or P0304 stored in the powertrain control module (PCM)
SSM 54857
Service Bulletin/Repair Instructions
2020-2026 Explorer/Escape/Corsair, 2021-2026 Bronco Sport/Bronco, 2022-2026 Maverick, 2024-2026 Mustang/Ranger/Nautilus vehicles equipped with a 2.0L or 2.3L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 2.0L/2.3L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure been added. In addition, the wastegate actuator rod (9E408), associated retention springs (9342) and retaining clips (00817) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate actuator assembly.
TSB 26-2185
Service Bulletin/Repair Instructions
This bulletin supersedes 25-2621. Reason for update: add 2026 model year vehicles and Transit, update the causal part number (15604), update the Service Procedure, update the service labor operations for 2023 F-Super Duty, and add service labor operations for Transit. Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.
SSM 54765
Service Bulletin/Repair Instructions
Some 2025-2026 Bronco, Bronco Sport, F-Super Duty, Maverick, Mustang, Mustang Mach-E, Ranger and Transit vehicles may exhibit a no audio/sound condition. This may be due to the software in the audio control module (ACM). To determine if it is a software concern, disconnect the vehicle's 12-volt battery cables for 10 minutes and reconnect. If the concern is still present, continue with normal diagnostics in Workshop Manual (WSM), Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing and repair as necessary outside of this article. If the no audio/sound concern is resolved, engineering is currently working on a solution for this condition that is expected by September 2026. Replacement or reprogramming of the ACM and or audio digital signal processing module (DSP) may not resolve this condition at this time. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a customer's vehicle exhibits this concern, submit a Vehicle Concern Report.
SYNC-26.2.4.11 Mustang
Over The Air
Quality improvements include: -Enhanced center screen stability
SSM 54719
Service Bulletin/Repair Instructions
For 20212026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. When referred to a specific clutch (A-F) test by a pinpoint test in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing, the Clutch Assembly tests have been updated with a hyperlink to the new Transmission Line Pressure Test - Pressure Vacuum Transducer (PVT) Is Available procedure in WSM, Section 307-01 > General Procedures. This procedure provides instructions to perform the FDRS Transmission Clutch Circuit Leak Test when applicable. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification
SSM 54720
Service Bulletin/Repair Instructions
Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
TSB 25-2587
Service Campaign
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
SSM 54674
Service Bulletin/Repair Instructions
For 2021-2026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. The Workshop Manual (WSM) has been updated under Section 307-01 > Diagnosis and Testing to include this procedure. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method.
ECG2-25.2.8.5 Mustang
Over The Air
26C10 Recall remedy -Addresses instances where the trailer lights and trailer brakes may not function
TSB 26-2112
Service Bulletin/Repair Instructions
This bulletin supersedes TSB 26-2059. Reason For Update: To add missing labor operations. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
TSB 26-2102
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit an illuminated yellow/red anti-lock brake system (ABS) warning indicator with diagnostic trouble codes (DTCs) C0037:01, C0037:07, C0037:2F, C0037:4A, C0037:64, C003A:01, C003A:07, C003A:2F, C003A:4A, and/or C003A:64 stored in the ABS module.
TCU-25.2.8.5 Mustang
Over The Air
26C10 Recall remedy -Addresses instances where the trailer lights and trailer brakes may not function
TSB 26-2059
Service Bulletin/Repair Instructions
This bulletin supersedes TSB 25-2423. Reason For Update: Replace the incorrect acronym SOWC with the correct acronym OWC. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
SSM 54601
Service Bulletin/Repair Instructions
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
SSM 54592
Service Bulletin/Repair Instructions
For 20172026 vehicles equipped with a 10R transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
SSM 54593
Service Bulletin/Repair Instructions
Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and/or may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the high-pressure fuel pump causing fuel to enter the crankcase and reduce fuel pressure in the direct injection fuel rail. Diagnose this condition using Pinpoint Test HP located in Workshop Manual (WSM), Section 303-04. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. Repair as necessary outside of this article. For claiming, if high-pressure fuel pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article.
TSB 25-2621
Service Bulletin/Repair Instructions
Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.
SSM 54313
Service Bulletin/Repair Instructions
Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
TSB 25-2423
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
SSM 54232
Service Bulletin/Repair Instructions
Some 2025 Mustang GTD vehicles built on or before 15-Jul-2025 may exhibit various suspension warning messages displayed in the instrument panel cluster (IPC) including but not limited to "Front Lift Not Available See Manual". The vehicle may also have diagnostic trouble code (DTC) C1041:92 stored in the vehicle dynamics control module (VDM). This may be due to the VDM software. To correct the condition, reprogram the VDM module using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 18B008 and labor operations 12651D and 12651D4.
SSM 54206
Service Bulletin/Repair Instructions
Some 2025 Mustang GTD vehicles may set diagnostic trouble code (DTC) U0420:82 in the image processing module a (IPMA) during a diagnostic self-test. This may be due to the module's DTC sensitivity during vehicle key-on/start-up. Replacement or reprogramming of the IPMA module may not resolve this condition. If no other DTCs are present, no warning indicators are illuminated while the engine is running, and no noticeable symptoms are present, no additional diagnostics or service is recommended for this condition at this time. Inform customers engineering is currently working on a solution for this condition that is expected in Q2 2026. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If this condition is encountered, use the "Submit Global Concern Report (GCR)" link at the upper right of the Vehicle ID tab to submit a report and reference this article number in the report.
25H03
Other
Harvest Program 25H03 Certain 2024 - 2025 Model Year Bronco, Bronco Sport, Corsair, Escape, Explorer, Maverick, Mustang, and Ranger Vehicles with 1.5L, 2.0L, or 2.3L Engine Spark Plug Replacemen
TSB 25-2386
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model Statement above may exhibit a quarter glass rubber moulding that is rolled over or folded in. This may be due to the installation of the quarter glass assembly.
SSM 54138
Service Bulletin/Repair Instructions
Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the fuel injection pump causing fuel to enter the crankcase and reduce fuel pressure in the high pressure fuel rail. Diagnose this condition using Pinpoint Test HP located in the Workshop Manual, Section 303-04A. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. For claiming, if fuel injection pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article. Note: Components damaged as a result of this failure mode
SSM 54090
Service Bulletin/Repair Instructions
Some 2021-2025 Ford and Lincoln vehicles equipped with SYNC4/Digital Experience may exhibit an unsuccessful telematics control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.
25P20
Other
Certain 2025 Model Year Bronco, Explorer, Mustang, and Ranger Vehicles Engine Coolant Temperature Sensor Replacement On all affected vehicles, the Engine Coolant Temperature sensor (ECT) may have a poor solder joint internally, causing a Diagnostic Trouble Code (DTC) to set against the sensor for an open circuit and the check engine light to illuminate
SSM 54067
Service Bulletin/Repair Instructions
For 2018-2024 Edge and 2018-2025 Mustang vehicles, if diagnostics lead to the sun visor as the causal part, a new lower level part is available (DS7Z-9904132-A). It is not necessary to replace the sun visor assembly if only the clip is damaged.
25B30
Other
Certain 2025 Model Year Mustang 60th Anniversary Vehicles Red Wheel Center Caps Replacement Dealers are to remove the black center wheel caps that are currently installed and replace with new red ones
SSM 53991
Service Bulletin/Repair Instructions
Some 2025 Mustang GTD vehicles may set diagnostic trouble code (DTC) U0420:82 in the image processing module a (IPMA) during a diagnostic self-test. This may be due to the module's DTC sensitivity during vehicle key-on/start-up. Replacement or reprogramming of the IPMA module may not resolve this condition. If no other DTCs are present, no warning indicators are illuminated while the engine is running, and no noticeable symptoms are present, no additional diagnostics or service is recommended for this condition at this time. Inform customers engineering is currently working on a solution for this condition that is expected in Q4 2025. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If this condition is encountered, use the "Submit Global Concern Report (GCR)" link at the upper right of the Vehicle ID tab to submit a report and reference this article number in the report.
SSM 53971
Service Bulletin/Repair Instructions
Some 2023-2025 Escape vehicles equipped with a 1.5L/2.0L EcoBoost engine, 2023-2025 Corsair vehicles equipped with a 2.0L EcoBoost engine, 2024-2025 Nautilus vehicles equipped with a 2.0L EcoBoost engine, 2024-2025 Mustang vehicles with a 2.3L EcoBoost engine, and 2025 Bronco/Explorer/Ranger vehicles equipped with a 2.3L EcoBoost engine may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). This may be due to the spark plugs and/or ignition coils. To correct the condition, refer to Workshop Manual (WSM), Section 303-07 for normal diagnostics.
SSM 53973
Service Bulletin/Repair Instructions
Some 2021-2024 Edge/Nautilus, 2021-2025 Bronco/Bronco Sport/E-Series/Escape/Corsair/Expedition/Navigator/Explorer/Aviator/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.
SSM 53974
Service Bulletin/Repair Instructions
Some 2024-2025 Mustang vehicles equipped with a 2.3L EcoBoost engine may require removal of the air conditioning compressor belt due to various concerns. Workshop Manual (WSM), Section 303-05 has been updated with improved removal and installation service procedure steps.
25B07
Other
Certain 2024-2025 Model Year Mustang Dark Horse Vehicles Equipped with Summer Only Tires Summer Tire Inspection
PT-25.8.0 Mustang
Over The Air
Quality improvements include: -On-Board Diagnostics calibration for an enhanced Intake air temperature sensor performance
SSM 53764
Service Bulletin/Repair Instructions
Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
SSM 53759
Service Bulletin/Repair Instructions
After replacement of any TRON module, the gateway module (GWM) and the TRON capable modules can set diagnostic trouble codes (DTCs) U211A, U211B, U211C, U3034, U3035, U3036, U35D9, U35DA and/or U35DB if the secret authentication security keys are not aligned between the modules, a loss of communication is occurring between modules and/or a module is not responding. This may be a result of missing the new module secret authentication security key obtained when running the Ford Diagnosis and Repair System (FDRS) "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure after replacement. When replacing a TRON capable module, run the FDRS "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure in the GWM tool box, not in the toolbox of the module with the DTC's, to distribute a new set of secret authentication security keys to all TRON-capable modules. Using the specific vehicle identification number (VIN), refer to Workshop Manual (WSM), Section 418-00 and 418-01 for updated DTCs, applicable TRON module listings and pinpoint tests.
SSM 53638
Service Bulletin/Repair Instructions
After replacement of any TRON module, the gateway module (GWM) and the TRON capable modules can set diagnostic trouble codes (DTCs) U211A, U211B, U211C, U3034, U3035, U3036, U35D9, U35DA and/or U35DB if the secret authentication security keys are not aligned between the modules, a loss of communication is occuring between modules and/or a module is not responding. This may be a result of missing the new module secret authentication security key obtained when running the Ford Diagnosis and Repair System (FDRS) "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure after replacement. When replacing a TRON capable module, run the FDRS "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure to distribute a new set of secret authentication security keys to all TRON-capable modules. Using the specific VIN, refer to Workshop Manual (WSM), Section 418-00 and 418-01 for updated DTCs, applicable TRON module listings and pinpoint tests.
SSM 53602
Service Bulletin/Repair Instructions
Some 2022-2025 Ford or Lincoln vehicles may exhibit DTCs B142E:78, B1432:78, and/or B1433:54 diagnostic trouble codes (DTCs) in the CCM. This may be due to non-factory sized tires that may cause inaccurate speedometer readings that can impact the functionality of the CCM. When a vehicle is modified in this manner, replacement or realignment of the CCM may impact the normal operation of the system and/or performance of radar and camera-based features. Repair or replacement of the CCM when a vehicle is equipped with non-factory size tires may not be warrantable and subject to chargeback.
SSM 53569
Service Bulletin/Repair Instructions
Some 2021-2025 Ford and Lincoln vehicles may exhibit diagnostic trouble code (DTCs) U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.
SSM 53530
Service Bulletin/Repair Instructions
Some 2021-2025 Ford vehicles may exhibit a condition where heated/cooled seats, heated steering wheel and/or front/rear defrost features will not turn on after a remote start is performed through the FordPass application or the key fob.
TSB 25-2074
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2384 to update the vehicle lines and model years affected.
SSM 53444
Service Bulletin/Repair Instructions
Some 2023-2025 Ford vehicles were not produced with a factory wired keyless entry keypad.
SSM 53343
Service Bulletin/Repair Instructions
Some 2025 Mustang Vehicles may exhibit a condition where the passive key will not program to the vehicle.