Vehicle report

2016 GMC YUKON

Compare every GMC YUKON yearNHTSA and EPA records

Service bulletins

1401 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

PIP4902W

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIT5099J

Service Bulletin/Repair Instructions

PI to help diagnose A/C concern

PIT5509N

Service Bulletin/Repair Instructions

This PI provides diagnostic tips for diagnosing electric trailer brakes issues.

PIT5509M

Service Bulletin/Repair Instructions

This PI provides diagnostic tips for diagnosing electric trailer brakes issues.

PIT3271Q

Service Bulletin/Repair Instructions

This preliminary information communicates information about how to determine if a wheel and tires size change is available.

PIP4902V

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIP6104

Service Bulletin/Repair Instructions

This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical Assistance Case in CX Connect.

PIT6483

Service Bulletin/Repair Instructions

This preliminary information communicates an issue with aftermarket LED headlights causing IPC warning messages and MIL along with several low speed lan DTCs.

PIT6400A

Service Bulletin/Repair Instructions

This PI Communications information on an alternative product dealers can use to perform 19-NA-255: Wax Coating on Frame Peeling, Metal Shows Corrosion/Rusting due to issue with getting product from current supplier listed in the bulletin.

PIP5700G

Service Bulletin/Repair Instructions

This PI communicates the proper part numbers for transmission connectors and internal harness to prevent confusion when ordering

PIP4902U

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIT5984A

Service Bulletin/Repair Instructions

This Preliminary information communicates a diagnostic tip for an issue where the starter stays engaged after the engine starts. Dealers are to suspect/monitor the crankshaft position sensor.

PIT5214G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer’s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

PIP5700F

Service Bulletin/Repair Instructions

This PI communicates the proper part numbers for transmission connectors and internal harness to prevent confusion when ordering

PIP6088

Service Bulletin/Repair Instructions

This PI Addresses a possible solenoid wiring fault and how to inspect the build date to identify

PIP6086

Service Bulletin/Repair Instructions

This PI advises dealers to inspect for a missing pump gasket if the vehicle exhibits no movement following a VB replacement

13598

Other

New Vehicle Monitoring Programs Section in IVH

PIT5479H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston.

22-NA-080

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of engine related shudder.

PIP4902T

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIC5650M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.

PIC6086J

Service Bulletin/Repair Instructions

This PI communicates a procedure to clean oil leaking from the rain sensor.

PIT6400

Service Bulletin/Repair Instructions

This PI Communications information on an alternative product dealers can use to perform 19-NA-255: Wax Coating on Frame Peeling, Metal Shows Corrosion/Rusting due to issue with getting product from current supplier listed in the bulletin.

PIP4902S

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

25-NA-156

Service Bulletin/Repair Instructions

This service bulletin provides information on Tire Sidewall Irregularities.

00-06-01-026R

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

PIT5074R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.

23-NA-153

Service Bulletin/Repair Instructions

The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

15-NA-010

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.

PI0281L

Service Bulletin/Repair Instructions

This preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when addressing underbody component corrosion with customers.

07-00-89-037W

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

18-NA-315

Service Bulletin/Repair Instructions

This service bulletin advises the tech to only replace the shock that is bad and not all shocks.

25-NA-087

Service Bulletin/Repair Instructions

This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use for certain repairs, such as Wiring Harness Repairs.

13-08-116-001K

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

25-NA-052

Service Bulletin/Repair Instructions

This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.

PIP5943A

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician on diagnostic aids to help with the diagnosis and repair of 8 Speed Transmissions

24-NA-098

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.

25-NA-065

Service Bulletin/Repair Instructions

This informational bulletin instructs the tech when fuel/fluid is needed to be tested and where it can be sent for analysis.

PIT5511F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure.  This is done to protect the Driver Information Center from damage.

08-03-10-006I

Service Bulletin/Repair Instructions

This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.

15-06-03-001F

Service Bulletin/Repair Instructions

This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.

19-NA-255

Service Bulletin/Repair Instructions

This service bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

17-NA-073

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding the field action courtesy transportation policy.

PIP5966A

Service Bulletin/Repair Instructions

This Preliminary information communicates Diagnostic aids for a no start or DTC'S following a transmission replacement

05-03-07-009L

Service Bulletin/Repair Instructions

This service bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles.

11-00-89-005Y

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

05-08-51-001L

Service Bulletin/Repair Instructions

This informational bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.

16-NA-109

Service Bulletin/Repair Instructions

This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.

07-00-89-037V

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

16-NA-019

Service Bulletin/Repair Instructions

This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares.

PIT5479G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

PIP5175F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.

10-08-110-001L

Service Bulletin/Repair Instructions

This service bulletin provides information on proper use of floor mats.

21-NA-043

Service Bulletin/Repair Instructions

This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.

22-NA-074

Service Bulletin/Repair Instructions

This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

01-08-42-001Q

Service Bulletin/Repair Instructions

This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.

09-06-04-026Z

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

20-NA-166

Service Bulletin/Repair Instructions

This service bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.

20-NA-132

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.

07-00-89-037U

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

18-NA-263

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).

PIT5074Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIT5962B

Service Bulletin/Repair Instructions

This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.

PIT6261

Service Bulletin/Repair Instructions

This Preliminary information communicates to dealers GM is working on a solution for outdated Apps

08-07-30-035I

Service Bulletin/Repair Instructions

This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.

19-NA-219

Service Bulletin/Repair Instructions

This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.

04-06-01-029K

Service Bulletin/Repair Instructions

This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.

PIP4723J

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIT5698E

Service Bulletin/Repair Instructions

This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.

PIT5569C

Service Bulletin/Repair Instructions

This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.

PIP6015

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM technical assistance case using the dealer case management tool.

24-NA-040

Service Bulletin/Repair Instructions

This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.

PIP6014

Service Bulletin/Repair Instructions

This Preliminary information communicates for Technicians installing a Service Replacement Transmission Assembly to contact Technical Assistance to make sure unit is not suspect of a snap ring concern prior to installation.

10-00-89-009F

Service Bulletin/Repair Instructions

This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).

01-06-01-011Q

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

PIP5621E

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer  technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.

99-00-89-019Z

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.

07-00-89-037T

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

23-NA-154

Service Bulletin/Repair Instructions

This bulletin provides information on Warranty Administration – Required Operating Procedures - 8 Points (U.S. Only).

04-06-04-051J

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

23-NA-219

Service Bulletin/Repair Instructions

This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.

20-NA-138

Service Bulletin/Repair Instructions

This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

08-07-30-026I

Service Bulletin/Repair Instructions

This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

18-NA-146

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).

PIP6000A

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician on a parts restriction on the Generation I 8 speed rear wheel drive valve bodies.

PIP5996A

Service Bulletin/Repair Instructions

This Preliminary information communicates diagnostic information for vehicles with transmission noise.

PIP6000

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician on a parts restriction on the Generation I 8 speed rear wheel drive valve bodies.

PIT5282G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness.  Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).

PIT5511E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure.  This is done to protect the Driver Information Center from damage.

PIT5099H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIC6086H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area.  Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.

PIP5996

Service Bulletin/Repair Instructions

This Preliminary information communicates diagnostic information for vehicles with transmission noise

PIT5509L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

PIT6212

Service Bulletin/Repair Instructions

This Preliminary information communicates an issue with the Hydrastar Electric Over Hydraulic trailer brake system causing a voltage spike into the trucks electrical system which is causing DTC C1114 to set.

07-00-89-036K

Service Bulletin/Repair Instructions

This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.

02-00-89-002X

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).

23-NA-142

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure for the techs to replace the forward check ball and separator plate if found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.

PIC5650L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

PIT3271P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

24-NA-174

Service Bulletin/Repair Instructions

The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.

General Communication

Service Campaign

Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.

05-03-08-002J

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.

18-NA-073

Service Bulletin/Repair Instructions

This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

23-NA-044

Service Bulletin/Repair Instructions

This service bulletin provides information on AGM batteries that require less frequent charging in storage.

PIT5481J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Starting with 2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.

PIP5569B

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.

PIT5195H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

01-00-89-010S

Service Bulletin/Repair Instructions

This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

07-06-01-016J

Service Bulletin/Repair Instructions

This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

23-NA-141

Service Bulletin/Repair Instructions

This informational bulletin advises the technician that the engine and related parts will be debited if found that the tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.

00-06-01-012N

Service Bulletin/Repair Instructions

This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

05-06-04-022V

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

16-NA-222

Service Bulletin/Repair Instructions

This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.

09-06-04-026Y

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

01-06-01-011P

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

24-NA-147

Service Bulletin/Repair Instructions

This service bulletin provides information on regular inspection of the Seat Belt Lap Anchor.

18-NA-306

Service Bulletin/Repair Instructions

This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).

PI0754G

Service Bulletin/Repair Instructions

This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.

16-NA-158

Service Bulletin/Repair Instructions

This service bulletin describes the U.S. Dealer Special Tool Loan Program process.

12-01-37-001G

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.

24-NA-141

Service Bulletin/Repair Instructions

GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.

20-NA-038

Service Bulletin/Repair Instructions

This informational bulletin explains the difference in AFM and DFM engines and what is and is not activated during this occurrence.

00-03-10-002M

Service Bulletin/Repair Instructions

This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.

17-NA-157

Service Bulletin/Repair Instructions

This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter.

99-04-20-002O

Service Bulletin/Repair Instructions

This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.

04-06-04-051I

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

16-NA-383

Service Bulletin/Repair Instructions

This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

22-NA-070

Service Bulletin/Repair Instructions

This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part replacements.

18-NA-099

Service Bulletin/Repair Instructions

This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.

22-NA-018

Service Bulletin/Repair Instructions

This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only).

18-NA-125

Service Bulletin/Repair Instructions

This service bulletin provides information for engine oil life monitor operation calculation.

20-NA-016

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.

08-07-30-035H

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

19-NA-136

Service Bulletin/Repair Instructions

This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.

16-NA-119

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.

09-00-89-008G

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

18-NA-067

Service Bulletin/Repair Instructions

This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.

06-00-89-029V

Service Bulletin/Repair Instructions

This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

10-08-110-001K

Service Bulletin/Repair Instructions

This service bulletin provides information on proper use of floor mats.

13-08-116-001J

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

15-00-89-004G

Service Bulletin/Repair Instructions

This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

00-03-10-006P

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).

17-NA-052

Service Bulletin/Repair Instructions

This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed.

10-08-45-001H

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.

23-NA-103

Service Bulletin/Repair Instructions

This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC).

07-00-89-037S

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

11-00-89-005X

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

PIP5596A

Service Bulletin/Repair Instructions

This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.

PIP5968

Service Bulletin/Repair Instructions

This Preliminary information communicates to have the dealer contact TAC with the transmission TUN number prior to transmission installation.

PIP5966

Service Bulletin/Repair Instructions

This Preliminary information communicates Diagnostic aids for a no start or DTC'S following a transmission replacement

PIT4322P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

19-NA-044

Service Bulletin/Repair Instructions

This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.

16-NA-338

Service Bulletin/Repair Instructions

This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

PIT6122

Service Bulletin/Repair Instructions

This Preliminary information communicates to dealers of a known issue with failed map update

22-NA-246

Service Bulletin/Repair Instructions

This service bulletin advises the technician that the possible cause may not be from a faulty clutch piston or extension housing and to perform testing on transmission for other possible issues, but it still may be possible on high mileage vehicles that orifices in housing may have come dislodged, causing the same customer concern.

PI0281K

Service Bulletin/Repair Instructions

This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

02-08-42-001J

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.

PI1394B

Service Bulletin/Repair Instructions

This PI bulletin advises the technician on the proper way to install the pistons in an engine.

PIP5601B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

PI0592I

Service Bulletin/Repair Instructions

This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

16-NA-361

Service Bulletin/Repair Instructions

This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle.

PIT5074P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIT5962A

Service Bulletin/Repair Instructions

This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.

PIT5214F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

03-00-91-001I

Service Bulletin/Repair Instructions

This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.

20-NA-159

Service Bulletin/Repair Instructions

This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).

PIP5943

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician on diagnostic aids to help with the diagnosis and repair of 8 Speed Transmissions

22-NA-225

Service Bulletin/Repair Instructions

This information bulletin advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by Rear of Transmission or Transfer Case Area.

05-00-89-029F

Service Bulletin/Repair Instructions

This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.

01-06-01-011O

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

17-NA-170

Service Bulletin/Repair Instructions

This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.

99-00-89-019Y

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.

02-00-89-002W

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).

10-00-89-006J

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIT5099G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIT5698D

Service Bulletin/Repair Instructions

This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.

07-08-49-020R

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

20-NA-142

Service Bulletin/Repair Instructions

This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving.

PIP4112T

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while cruising at highway speeds and then an aggressive increase in throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.

PIP5621D

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer  technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.

09-00-89-016H

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.

PIP5628G

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

15-00-89-004F

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

01-00-89-010R

Service Bulletin/Repair Instructions

This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

04-06-04-051H

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

09-06-04-026X

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

17-NA-066

Service Bulletin/Repair Instructions

This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.

PIP5358C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

21-NA-026

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.

99-09-40-005I

Service Bulletin/Repair Instructions

This service bulletin provides information on availability for a seat belt extender.

PIP4902R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

01-06-01-011N

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

99-08-51-001F

Service Bulletin/Repair Instructions

This service bulletin provides information on Paintless Dent Repair Process.

13-08-116-001I

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

PIT4261J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

04-07-30-013E

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.

02-00-89-002V

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

08-07-30-026H

Service Bulletin/Repair Instructions

This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

12-03-10-001E

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

PIC5650K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

01-08-42-001P

Service Bulletin/Repair Instructions

This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.

11-00-89-005W

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

PIP5628F

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

12-03-10-001D

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

04-00-89-015Z

Service Bulletin/Repair Instructions

This bulletin provides information on Warranty Administration – Required Operating Procedures - 8 Points (U.S. Only).

08-07-30-035G

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

10-08-110-001J

Service Bulletin/Repair Instructions

This service bulletin provides information on proper use of floor mats.

11-00-89-005V

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

PI0281J

Service Bulletin/Repair Instructions

This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

00-06-01-012M

Service Bulletin/Repair Instructions

This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

00-06-01-026Q

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

22-NA-009

Service Bulletin/Repair Instructions

This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.

07-06-01-016I

Service Bulletin/Repair Instructions

This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

15-06-01-002O

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

16-NA-130

Service Bulletin/Repair Instructions

This service bulletin provides information for after installation of a replacement upper valve body, the transmission may have no Reverse and no 2nd gear.

15-NA-017

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.

PI0754F

Service Bulletin/Repair Instructions

This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.

99-04-20-002N

Service Bulletin/Repair Instructions

This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.

PIT4322N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

01-08-42-001O

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

15-06-01-002N

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

PIP5628E

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

00-00-90-002M

Service Bulletin/Repair Instructions

This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.

07-03-16-004E

Service Bulletin/Repair Instructions

This service bulletin provides information for tire pressure monitoring (TPM) system concerns.

02-00-89-002U

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

15-06-01-002M

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

23-NA-001

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.

09-00-89-008F

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

PIP5540J

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

21-NA-124

Service Bulletin/Repair Instructions

This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

PIP5632G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIP4902Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIT3271N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

22-NA-216

Service Bulletin/Repair Instructions

This bulletin advises the technician to Inspect the position of the head gasket locating tabs to determine if the head gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running Hot.

22-NA-205

Service Bulletin/Repair Instructions

This service bulletin provides information on Module Harvesting.

N182180270

Service Bulletin/Repair Instructions

Special Coverage. General Motors announced Special Coverage N182180270 on November 26, 2019. We are reminding dealers to review the Applicable Warranties section in IVH to determine if this Special Coverage applies.

10-00-89-006I

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

99-00-89-019X

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.

PIC5453D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

22-NA-185

Service Bulletin/Repair Instructions

This informational bulletin explains how the trans slip or flare can be a normal condition.

22-NA-195

Service Bulletin/Repair Instructions

This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.

PIT5698C

Service Bulletin/Repair Instructions

This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.

PI0592G

Service Bulletin/Repair Instructions

This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

05-06-04-022T

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

06-00-89-031H

Service Bulletin/Repair Instructions

This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.

07-06-01-016H

Service Bulletin/Repair Instructions

This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

13-08-116-001H

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

15-00-89-004E

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

01-00-89-010Q

Service Bulletin/Repair Instructions

This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

05-00-89-072F

Service Bulletin/Repair Instructions

This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.

09-06-04-026W

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

PIP5621C

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer  technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.

00-06-01-012L

Service Bulletin/Repair Instructions

This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

01-06-01-011M

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

04-06-04-051G

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

00-06-01-026P

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

11-00-89-005U

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

05-00-89-029E

Service Bulletin/Repair Instructions

This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.

22-NA-176

Service Bulletin/Repair Instructions

This technical bulletin provides information on a possible bolt and guide pin that may be missing from the control valve which will need to be installed to correct the repair.

22-NA-181

Service Bulletin/Repair Instructions

This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.

PIP5640A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

11-00-89-005T

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

20-NA-065

Service Bulletin/Repair Instructions

This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

21-NA-199

Service Bulletin/Repair Instructions

This informational bulletin advises the technician to replace the TBV if the transmission has any type of repair even if no problem was found, to replace the tbv.

04-00-89-015X

Service Bulletin/Repair Instructions

This bulletin provides information on Warranty Administration – Required Operating Procedures - 8 Points (U.S. Only).

PIT5569B

Service Bulletin/Repair Instructions

This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.

PIT4261H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

22-NA-135

Service Bulletin/Repair Instructions

This warranty admin bulletin covers information on Essential Tools that include Consumable Parts.

12-01-37-001F

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.

PIC5260F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIT5681C

Service Bulletin/Repair Instructions

This Preliminary information communicates the location of the GM Accessory Performance Brake System Rotor Specifications

PIT5448H

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

PIT5099F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIP5358B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

PIP5856

Service Bulletin/Repair Instructions

This Preliminary information communicates provides information to the technician on the use of R-99 or R-95  Renewable diesel fuel.

22-NA-106

Service Bulletin/Repair Instructions

This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires.

14-06-04-004H

Service Bulletin/Repair Instructions

This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours.

12-00-89-003B

Service Bulletin/Repair Instructions

This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).

20-NA-050

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to clear the codes and test the Tcase if found that the customer has tried to shift the t-case from 4lo to Hi gears while driving.

PIT5556A

Service Bulletin/Repair Instructions

This Preliminary information communicates an issue where the chassis wiring harness can chaff on the underbody of the vehicle causing a wide varied of issues, depending on which wire(s) is chaffed. Repair the affected wiring as needed

PIC5260E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

01-00-89-010P

Service Bulletin/Repair Instructions

This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

PI0281I

Service Bulletin/Repair Instructions

This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

01-00-89-010O

Service Bulletin/Repair Instructions

This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

15-06-01-002L

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

PIP4670J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.

04-06-04-051F

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

18-NA-161

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.

PIT3271M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

20-NA-207

Service Bulletin/Repair Instructions

This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set.

22-NA-047

Service Bulletin/Repair Instructions

Information bulletin explains a possible coolant leak coming from the cylinder head bolt areas.

PIC6450

Service Bulletin/Repair Instructions

This Preliminary information communicates a process to correct the concern of Unable to contact OnStar after the 3G EOL on 2015-2022 model year vehicles in the United States.

PIT3271L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

090604026V

Service Bulletin/Repair Instructions

Information.

080089014G

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

22NA018

Service Bulletin/Repair Instructions

This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only).

990089019W

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.

070601016G

Service Bulletin/Repair Instructions

This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

150089004D

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

18NA067

Service Bulletin/Repair Instructions

This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.

PI0653F

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.

16NA361

Service Bulletin/Repair Instructions

This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle.

PIT4322M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

18NA235

Service Bulletin/Repair Instructions

This information bulletin advised the tech of possible use of low fuel quality and the possible ramifications in performance in regards to the customers concerns.

18NA073

Service Bulletin/Repair Instructions

This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

PIP4902P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIP4723F

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIP5632F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

22NA009

Service Bulletin/Repair Instructions

This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.

070316004D

Service Bulletin/Repair Instructions

This service bulletin provides information for tire pressure monitoring (TPM) system concerns.

16NA222

Service Bulletin/Repair Instructions

This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.

000090002L

Service Bulletin/Repair Instructions

This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.

050604022S

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

1308116001G

Service Bulletin/Repair Instructions

The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

PIP5811

Service Bulletin/Repair Instructions

This Preliminary information communicates to dealers an issue on remanufactured engines with part numbers 19368174  and 19368176 where the incorrect crankshaft timing gear was installed. Provides dealer with information to correct this condition.

20NA166

Service Bulletin/Repair Instructions

This informational bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.

19NA153

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM for metal.

030310007K

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires.

19NA104

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area.

030091001H

Service Bulletin/Repair Instructions

This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.

PIT5245D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the blower motor may be noisy or vibrate when running. This concern will only occur when the temperatures is below 32 degrees Fahrenheit and if the blower motor is removed while still cold, ice may be found on the blower motor cage. This concern could be caused by water leaking or snow ingestion into the Heater-Vent-Air Conditioning case. Technician is to perform normal water testing diagnostics while the Heater-Vent-Air Conditioning is running, looking for water leaking past the plenum cover. If water is leaking past the cover remove the cover and install a 12x12 snow resistant screen to the fresh air intake. Reseal and install the plenum cover cap using Kent air dry sealer or equivalent.

PIT3099U

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

20NA132

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

17NA308

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of carpet damage, seat mounting stud wear through, hole in second row (Intermediate) carpet.

17NA345

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to reprogram the power steering control module to correct a condition of Loss of Steering Assist due to a software abnormality.

PIC5650J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

PIT5698B

Service Bulletin/Repair Instructions

This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.

PIP5813

Service Bulletin/Repair Instructions

This Preliminary information communicates A vehicle may have a need for  Camshaft replacement or have misfires on non AFM cylinders after the camshaft was replaced. The camshaft may have been boxed incorrectly

21NA152

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint percentage.

010842001N

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

PIT4261G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

990420002L

Service Bulletin/Repair Instructions

This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.

PIP5632E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

080730035E

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

110089002E

Service Bulletin/Repair Instructions

This service bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.

070089037Q

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

PIP5621B

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer  technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.

21NA124

Service Bulletin/Repair Instructions

This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

PIT5681B

Service Bulletin/Repair Instructions

This Preliminary information communicates the location of the GM Accessory Performance Brake System Rotor Specifications

18NA306

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).

070089037P

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

100089006H

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIT4322L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

PIP5358A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

PIT5214E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

20NA159

Service Bulletin/Repair Instructions

This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).

19NA044

Service Bulletin/Repair Instructions

This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.

21NA109

Service Bulletin/Repair Instructions

This service bulletin provides diagnostic information for a customer concern of engine vibration.

16NA338

Service Bulletin/Repair Instructions

This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

21NA103

Service Bulletin/Repair Instructions

This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition.

000601026N

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

17-NA-335

Service Bulletin/Repair Instructions

Malfunction Indicator Lamp Illuminated (MIL) - DTC P2635 and/or P018B Set In High Ambient Temperatures With Hesitation, Surging and Stalling Condition Some customers may comment that the Malfunction Indicator Light (MIL) is illuminated. Some customers may also comment on one or more of the following symptoms: • Hesitation • Surging • Stalling Note: In ambient temperatures 100 F (37.7 C) degrees or higher, DTCs P2635 and/or P018B may set. The Technician may find one or more of the following DTCs set: • P2635 • P018B Cause This condition may be caused by a vapor buildup in fuel feed line. Correction If the conditions stated above are met, replace the fuel pump module with an updated version

050308002I

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.

20NA038

Service Bulletin/Repair Instructions

This informational bulletin explains the difference in AFM and DFM engines and what is and is not activated during this occurrence.

18NA146

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).

020089002T

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

070089036J

Service Bulletin/Repair Instructions

This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.

18NA099

Service Bulletin/Repair Instructions

This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.

PIP5163E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIC5260D

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIP5540G

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PIP5725A

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use.  Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement.  This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.

110089005Q

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

1008110001I

Service Bulletin/Repair Instructions

This informational bulletin provides information on proper use of floor mats.

20NA138

Service Bulletin/Repair Instructions

This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

19NA255

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

21NA043

Service Bulletin/Repair Instructions

This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.

16NA109

Service Bulletin/Repair Instructions

This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.

150089004C

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

21NA026

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.

18NA285

Service Bulletin/Repair Instructions

This informational bulletin advises the tech of a possible normal condition when the vehicle creeps forward during start up conditions when the clutch packs are full of residual oil.

21NA010

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to reset the DTCs and take the vehicle for a test drive to verify the codes do not return.

PI1513G

Service Bulletin/Repair Instructions

This preliminary information bulletin provides a procedure for radiator and engine coolant thermostat replacement to eliminate coolant smell and/or a slight leak at the radiator.

20NA142

Service Bulletin/Repair Instructions

This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving.

150601002K

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

010601011L

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

16NA171

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to reinstall the rear defroster tab on the rear window defogger for vehicles with the condition of rear defrosters inoperative or if one is to break during a normal repair.

17NA166

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to measure vibration and install engine mounts to correct a Rough Idle in Drive concern.

PIC6086G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area.  Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.

090604026S

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

040089015V

Service Bulletin/Repair Instructions

This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).

16NA019

Service Bulletin/Repair Instructions

This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares.

19NA136

Service Bulletin/Repair Instructions

This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.

18NA263

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).

PIT5404G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming.  Replace or repair any of the issue that was found in the inspection. If the vehicle is equipped with a 4.3 liter or 5.3 liter engine an updated exhaust system is now available.

060089031F

Service Bulletin/Repair Instructions

This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.

PIT5074N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

000310002L

Service Bulletin/Repair Instructions

This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.

RFI20201112_751-

Service Bulletin/Repair Instructions

This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.

PIT3271K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

990851001E

Service Bulletin/Repair Instructions

Thins informational bulletin provides information on Paint-less Dent Repair Process.

PI0754D

Service Bulletin/Repair Instructions

This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.

19NA116

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of pulsing, grinding, scraping noise from brakes, uneven front brake pad wear.

1308116001F

Service Bulletin/Repair Instructions

The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

PIP5684C

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.

050604022R

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

18NA315

Service Bulletin/Repair Instructions

This informational bulletin advises the tech to only replace the shock that is bad and not all.

060089026Q

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated (CCND) Labor Operation Numbers.

PIP5628C

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

20NA207

Service Bulletin/Repair Instructions

This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set.

N182202780-02

Service Bulletin/Repair Instructions

Special Coverage Adjustment - In some circumstances, some 2014-2018 model year Cadillac Escalade, Chevrolet Silverado, Chevrolet Suburban, Chevrolet Tahoe, GMC Sierra, and GMC Yukon vehicles may have a condition where customers may experience increased brake pedal effort, hard brake pedal, and/or potentially increased stopping distance. The condition is more prevalent at low speed when softly applying the brakes. The engine mounted mechanical vacuum pump output may decrease over time decreasing the amount of vacuum/power brake assist. Failure to follow recommended oil change intervals could contribute to this condition. The Driver?s Information Center, (DIC) ?Service brake assist? alert will activate 2-5 minutes after the vacuum level drops, and a Diagnostic Trouble Code, (DTC) will also be set. Even where this condition occurs, the hydraulic brake system remains functional but may require additional pedal force. Dealers are to replace the vacuum pump and vacuum pump belt. The repairs will be made at no charge to the customer.

110089005P

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

18NA161

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.

20NA157

Service Bulletin/Repair Instructions

This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.

19NA036

Service Bulletin/Repair Instructions

This Bulletin provides the technician with information on how to perform a oil consumption test and a procedure to replace the pistons if found the cause of the oil consumption.

990089019U

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.

16NA205

Service Bulletin/Repair Instructions

This Technical bulletin provides a procedure to correct a customer concern of Blu-Ray Movies Do Not Start After Play Icon Selected on Menu.

N192291660

Service Bulletin/Repair Instructions

Special Coverage Adjustment - certain vehicles with a 6.2L engine may have a condition that affects the electrical connection to the transmission oil temperature sensor. If this condition occurs, rough transmission shifts or hesitation during acceleration may occur. Additionally, the Malfunction Indicator Light (Check Engine Light) would illuminate and a diagnostic trouble code related to the temperature sensor would set. Dealers are to replace the transmission wiring harness as necessary. The repairs will be made at no charge to the customer.

PIP5226D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

PIT5099E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIC5650H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

PIT5533C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.

PIT5698A

Service Bulletin/Repair Instructions

This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.

17336 06

Service Bulletin/Repair Instructions

Special Coverage (Diagnosis Time Added). On some vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. This special coverage covers the condition described above for a period of 5 years or 60,000 miles (100,000 km) for Chevrolet Suburban, Tahoe, GMC Yukon and Yukon XL and 6 years or 72,000 miles (116,000 km) for Cadillac Escalade and Escalade ESV, whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.

17336 07

Service Bulletin/Repair Instructions

Special Coverage (Parts Ordering Information Added). On some vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. This special coverage covers the condition described above for a period of 5 years or 60,000 miles (100,000 km) for Chevrolet Suburban, Tahoe, GMC Yukon and Yukon XL and 6 years or 72,000 miles (116,000 km) for Cadillac Escalade and Escalade ESV, whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.

PIP5684B

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.

150089002B

Service Bulletin/Repair Instructions

This bulletin provides information to dealers regarding transportation damage repair claim submission requirements.

PIP5504F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians are referred to Torque Converter Diagnosis in SI.

PIT5311F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle?s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector with part number 23404450.

PIP4902N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIP5741

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer technician that if after replacing the valve body on an 8L45 or 8L90 transmission the vehicle will not move the valve body may be missing a plug and retainer bolt. Technician's are instructed to obtain and install a plug and retainer bolt kit from the GM Warranty Parts Center to address this concern.

990089019T

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.

PIT5564C

Service Bulletin/Repair Instructions

This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set.

PIC5453C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

110089005O

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).

060089029T

Service Bulletin/Repair Instructions

This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

140604004G

Service Bulletin/Repair Instructions

This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours.

PIP5628B

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

PIT5681A

Service Bulletin/Repair Instructions

This Preliminary information communicates the location of the GM Accessory Performance Brake System Rotor Specifications

070849020Q

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

N182180270 01

Service Bulletin/Repair Instructions

Special Coverage. On some 2015-2017 model year GMC Yukon, Yukon XL, Yukon Denali, and Yukon Denali XL vehicles, stop and tail functions inside the tail lamps may become inoperative. Dealers are to replace tail lamps if they are found to be inoperative. The repairs will be made at no charge to the customer.

16NA383

Service Bulletin/Repair Instructions

This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

PIP5725

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use.  Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement.  This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.

030089006R

Service Bulletin/Repair Instructions

This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.

060089029S

Service Bulletin/Repair Instructions

This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

20NA098

Service Bulletin/Repair Instructions

This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC.

PIP5684A

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.

150601002J

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

090089002R

Service Bulletin/Repair Instructions

This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.

000310003Z

Service Bulletin/Repair Instructions

This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).

060089029R

Service Bulletin/Repair Instructions

This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

PIT5511D

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure.  This is done to protect the Driver Information Center from damage.

PIC5650G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

20NA093

Service Bulletin/Repair Instructions

This informational bulletin provides information on Normal Radio Display Operation ? Display Does Not Remain Off at Times After Being Turned Off in Settings and no parts should be replaced due to this condition.

PI0281H

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

PIT4322K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

060089029Q

Service Bulletin/Repair Instructions

This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.

19NA035

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as intended, causing the parking pawl to engage while driving.

100089005I

Service Bulletin/Repair Instructions

This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.

18NA355

Service Bulletin/Repair Instructions

This technical bulletin provides information for new transmission oil to use and a procedure for exchanging the old fluid and adding the new fluid to correct a shake/shudder during light throttle acceleration condition.

PIT5622B

Service Bulletin/Repair Instructions

This Preliminary information communicates instructions dealer to inspect for a broken or damaged side objector sensor/module bracket if there is a "Side Detection System Unavailable" message displayed at startup.

060089029P

Service Bulletin/Repair Instructions

This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.

PIT5426C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician for a water leak in in the second and third row seating area. Inspect the C-pillar which is the body vertical structure behind the rear passenger door area of the affected side of the vehicle for water intrusion or water marks on the seat belt retractor. If water evidence is found on the seat belt webbing or the retractor the seat belt/ retractor must be replaced after the water leak has been corrected and verified. There are 3 areas of seam sealer that will need to be addressed. After gaining access to the C-pillar and rear quarter panel area inspect for voids or missing seam sealer and apply a clear flow able seam sealer where needed.

070089037O

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance programs.

140604004F

Service Bulletin/Repair Instructions

This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours.

150601002I

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.

PIT4261F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

020089002S

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

050310020G

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.

060089026P

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated (CCND) Labor Operation Numbers.

990089019S

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.

040601029J

Service Bulletin/Repair Instructions

This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules.

19NA219

Service Bulletin/Repair Instructions

This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.

040089015U

Service Bulletin/Repair Instructions

This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).

N192285050

Service Bulletin/Repair Instructions

Customer Satisfaction Program - Certain vehicles that had the front passenger seat cushion frame previously replaced, may not have had the adjuster stops transferred and are missing on the replacement part. The front passenger seat may be in a position beyond the occupant design travel range.Dealers are to inspect the front passenger seat tracks for the presence of both adjuster stops and install missing adjuster stops if necessary.

000310003Y

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

PIT5452C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a pop, click, tick, snap, or itch type noise in the steering column or steering wheel when turning left or right during low speeds or parking maneuvers. Technician will need to inspect for mis-routed airbag module wiring harness for contacting vibration damper plate in steering wheel, or replace the column upper bearing inner race, spring, and seat.

PIT5307G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a service engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.

050307009J

Service Bulletin/Repair Instructions

This informational bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles.

150089005C

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on Essential Tools that include Consumable Parts (U.S. Only).

16NA119

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.

17NA304

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace both fuel feed lines for a leak and/or noise coming from pulses in the fuel line.

PIT3099T

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

DOR-D8C4T-03

Service Bulletin/Repair Instructions

This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.

DOR-E2P5T-03

Service Bulletin/Repair Instructions

This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.

PIP4723D

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

110089002D

Service Bulletin/Repair Instructions

This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.

19NA212

Service Bulletin/Repair Instructions

This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away to correct a crank/No Start condition.

050307009I

Service Bulletin/Repair Instructions

This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.

15NA010

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.

20NA016

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.

PIP5540F

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PIP5130K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.

PIP5503B

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being overfull on oil causing an engine vibration concern. The technician is advised to inspect for contaminnants and adjust the engine oil level as needed.

PIP5531A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015?0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that "mating" surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped

PI0592F

Service Bulletin/Repair Instructions

This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

100089009D

Service Bulletin/Repair Instructions

This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.

080089014F

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

PIP5621A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer  technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.

19NA137

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to add PET tape to the brake cables if the cause of the customers concern.

18NA137

Service Bulletin/Repair Instructions

This Bulletin provides information for rebuilding fuel injectors in the event of an underhood fuel odor and/or extended cranking condition.

010842001M

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.

080310006G

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.

PIT3271J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIT5594B

Service Bulletin/Repair Instructions

This Preliminary information communicates a normal DIC message after learning keys/fobs which indicates the drivers memory position.

PIT5074M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

990420002K

Service Bulletin/Repair Instructions

This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.

17NA291

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the radio for vehicles with the condition of Intermittent Pop Noise from the Speakers Followed by a Reset of the Radio and Clock due to a software issue.

PIT5550C

Service Bulletin/Repair Instructions

This Preliminary information communicates that an inoperative third row folding seat back may not fold down or up.  This information advises dealers on how the seat functions and also a common area where an open circuit may be found between the third row seat module and the seat position sensor.  It provides repair instructions if a concern is found with the circuits between the third row folding seat module and the seat back position sensor, as well as advising the dealer to look for bent/damaged seat recline mechanisms.

PIT5447C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps needed to diagnose and repair vehicles that may have a rattle noise from the dash. Technician will need to inspect for the rear heater pipes contacting the passenger side exhaust manifold.  If the rear heater pipe is found to be contacting the exhaust manifold, reposition the heater pipe so it no longer makes contact.

PIE0529A

Service Bulletin/Repair Instructions

This engineering information bulletin ends the need for information from the field on an Intermittent No Forward and/or No Reverse While Driving condition. If this condition is encountered, refer to SI for further diagnosis.

PIP5684

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.

100089006G

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).

PIT5604B

Service Bulletin/Repair Instructions

This Preliminary information communicates if the liftglass will not open using keyless entry to verify Valet Mode is not enabled.

PIP5540E

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

N182202780 01

Service Bulletin/Repair Instructions

N182202780 01 - Special Coverage. Certain Vehicles may have a condition where customers may experience increased brake pedal effort, hardbrake pedal, and/or potentially increased stopping distance. The condition is more prevalent at low speed when softly applyingthe brakes. The engine mounted mechanical vacuum pump outputmay decrease over time decreasing the amount of vacuum/power brake assist. Failure to follow recommended oil change intervalscould contribute to this condition. The Driver?s Information Center, (DIC) ?Service brake assist? alert will activate 2-5minutes after the vacuum level drops, and a Diagnostic Trouble Code, (DTC) will also be set. Even where this condition occurs,the hydraulic brake system remains functional but may require additionalpedal force. Please be aware that even if the vehicle exhibits this condition, it meets all federal motor vehicle safety standards forbrake performance. Dealers are to replace the vacuum pump and vacuum pump belt. The repairs will be made at no charge to the customer.

PIP5601A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

010601011K

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

100089009C

Service Bulletin/Repair Instructions

This informational bulletin provides information on key code security and information on GM key code look up applications.

010089010N

Service Bulletin/Repair Instructions

This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).

PIP5407B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.

PIT5576C

Service Bulletin/Repair Instructions

This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar.   Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.

PIP4670H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.

17NA073

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding the field action courtesy transportation policy.

17336 05

Service Bulletin/Repair Instructions

17336 05 - Special Coverage. On some vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. This special coverage covers the condition described above for a period of 5 years or 60,000 miles (100,000 km) for Chevrolet Suburban, Tahoe, GMC Yukon and Yukon XL and 6 years or 72,000 miles (116,000 km) for Cadillac Escalade and Escalade ESV, whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.

PIP5632B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIT3099S

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

PIP5407A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.

16NA042

Service Bulletin/Repair Instructions

This Technical Bulletin provides procedures to upgrade a vehicle with the Android Auto feature for 2016 and 2017 Model Year vehicles.

PI0592E

Service Bulletin/Repair Instructions

This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961).

090604026R

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

130089008B

Service Bulletin/Repair Instructions

This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC.

000601026M

Service Bulletin/Repair Instructions

This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

070601016F

Service Bulletin/Repair Instructions

This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

080730026F

Service Bulletin/Repair Instructions

This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

PIT5288G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.

PIT5572C

Service Bulletin/Repair Instructions

This Preliminary information communicates a Service Adaptive Cruise With DTC C018C SYM3A After Replacing K14 Distance Sensing Cruise Control Module and provides tips for completing all necessary steps and to contact TCSC if configuration does not complete correctly.

PIC6086F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area.  Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.

PIE0529

Service Bulletin/Repair Instructions

This engineering information bulletin is requesting information from the field to validate a field fix. Before contacting engineers, remove the transmission oil pan and inspect for nickel to quarter size pieces of aluminum debris in the oil pan. The 2-3-4-6-8 and 4-5-6-7-8 reverse clutch assembly and the 1-3-5-6-7 clutch assembly may be broken in several pieces.

PIT5698

Service Bulletin/Repair Instructions

This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.

990089019R

Service Bulletin/Repair Instructions

This informational bulletin provides process information for the (GWM) and (WPC) parts return program.

N182198000

Service Bulletin/Repair Instructions

N182198000 - Special Coverage Adjustment - Certain vehicles, equipped with a 5.3L or 6.2L engine, may have a condition which affects fuel injector function. Under certain circumstances one or more of the vehicle?s fuel injectors may deliver an improper amount of fuel to the engine. If this occurs, the Malfunction Indicator Lamp (Check Engine Light) will illuminate, the engine may idle or run rough, and the vehicle may stall. A diagnostic trouble code related to the fuel injector may be set. This special coverage only applies to vehicles in these states: California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont, and Washington. Dealers are to replace the fuel injectors as necessary. The repairs will be made at no charge to the customer.

19NA142

Service Bulletin/Repair Instructions

This technical bulletin provides information for new transmission oil to use, a procedure for exchanging the old fluid and adding the new fluid to a service transmission.

PI1344C

Service Bulletin/Repair Instructions

This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.

PIT5569A

Service Bulletin/Repair Instructions

This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.

PIT5622A

Service Bulletin/Repair Instructions

This Preliminary information communicates instructions dealer to inspect for a broken or damaged side objector sensor/module bracket if there is a "Side Detection System Unavailable" message displayed at startup.

19NA081

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some SiriusXM Channels Due to Interference in Some Geographic Locations.

PIT3099R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.

050604022Q

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

100845001G

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.

1308116001E

Service Bulletin/Repair Instructions

The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

000601012J

Service Bulletin/Repair Instructions

This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

090604026Q

Service Bulletin/Repair Instructions

This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

PIT5530C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory Accessory 22" Wheels Regular Production Option Code (SES, SEU, SEY, OR SEZ)  or production 22" wheels Regular Production Option Code (RPT or SMI) also during any service requiring wheel removal.

19NA139

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to pry the upper and lower quarter rear trim panel sheet metal apart to eliminate a creak noise heard from the quarter lower rear trim panel area.

PIP4670G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.

060847001O

Service Bulletin/Repair Instructions

This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.

19NA125

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians and customers on possible carpet color mismatch.

PIT5572B

Service Bulletin/Repair Instructions

This Preliminary information communicates a Service Adaptive Cruise With DTC C018C SYM3A After Replacing K14 Distance Sensing Cruise Control Module and provides tips for completing all necessary steps and to contact TCSC if configuration does not complete correctly.

PIT5202E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission, now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.

PIT5074L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIP5298B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician for a Service Engine Soon light with a Diagnostic Trouble code P0300 set. There may be a rough running engine associated with this concern. If service information diagnostics have been completed and there is still no trouble found, the technician is to inspect for a possible terminal tension concern on the ignition coil power feed for the cause of the rough running engine and or the P0300.  For the Service Engine Soon light or traction control lamp concern check the X2 connector of the under hood fuse block for poor pin retention.

PIP5632A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

080730035D

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

PIT5049E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.

PIT3219F

Service Bulletin/Repair Instructions

This Preliminary Information communicates to technicians that the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49).   These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.

000310006N

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).

PIT5681

Service Bulletin/Repair Instructions

This Preliminary information communicates the location of the GM Accessory Performance Brake System Rotor Specifications

PIP5640

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

PIP5644

Service Bulletin/Repair Instructions

This Preliminary information communicates Check Engine Light on and vehicle runs rough.  This condidtion will occur within the first 5 minutes after the vehicle is started.  his condition may be caused by a software anomaly that allows all four DTC's P0132, P0137, P0152, P0157 to set.  All 4 DTCs must be in history for this PI to apply.

PIP5226C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

080089014E

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

140604004E

Service Bulletin/Repair Instructions

This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours.

17NA153

Service Bulletin/Repair Instructions

This informational bulletin provides information and operating tips for the hands free lift gate.

PIP5569A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.

PIC5260C

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIC6360

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Technician should check the installation of the COAX cables to be router correctly.  Technician will gain access to the Radio or Human Machine Interface depending on the vehicle build.  Install the EL-50334 test antenna to the Radio HMI and evaluate the operation. If the GPS signal is restored, inspect for incorrect coax routing as described above and if found, reroute the cable so it does not bypass the splitter.

18NA377

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of front seat lateral movement and/or click type noise while driving.

PIP5423B (1)

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.

PIP5369C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have "Service 4 Wheel Drive" message on the Driver Information Center. Provides the technician with additional information to ensure that the TCCM contains the latest software released to address previous issues, also advises of default action changes. Calls out specific circuits to be inspected to help isolate intermittent codes.

PIP5423B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.

19NA072

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Rear Compartment Floor Stowage Compartment Cover Handle Availability as Service Part.

PIP5423A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.

17NA267

Service Bulletin/Repair Instructions

This informational bulletin provides information for 22" accessory wheel/tire usages.

PIP4670F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.

030603004Y

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

1008110001H

Service Bulletin/Repair Instructions

This informational bulletin provides information on proper use of floor mats.

110089005N

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.

030089006Q

Service Bulletin/Repair Instructions

This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.

060089029O

Service Bulletin/Repair Instructions

This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.

040089053G

Service Bulletin/Repair Instructions

This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.

070849020P

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

1008110001G

Service Bulletin/Repair Instructions

This informational bulletin provides information on proper use of floor mats.

PIT5379E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a content theft alarm sounding for no apparent reason. Technician may use all published Service Information diagnostics and has not found the cause of the unwanted content theft alarm sounding. Technician should use Global Diagnostic System 2 to review the Body Control Module parameters for "Content Theft Deterrent Trigger History". If the trigger is an Intrusion inspect for items hanging from the rear view mirror, solar powered dancing characters. When the trigger is a Glass breakage inspect the two rear quarter-panel windows and also in the liftgate glass. The quarter panel windows are attached to the body harness with a connector that looks similar to a 9 volt battery connector inspect them to be fully seated in on the glass. When the trigger is Ignition Voltage/Battery reconnect detected during a cold ambient temperature remote vehicle start event technician should call GM General Motors Technical Assistance Center.

16NA111

Service Bulletin/Repair Instructions

This informational bulletin provides diagnostic/inspection information for the air box and air filter seal to correct a MIL and DTCs P0420 and P0430 setting.

PIP4902M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIE0500A

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information to check the shutters through the grille opening of the vehicle. If snow and/or ice is present on the active grille air shutters, take pictures and submit through the Field Reporting Process.

100845001F

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".

PIT5511C

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure.  This is done to protect the Driver Information Center from damage.

090089002Q

Service Bulletin/Repair Instructions

This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.

PIP5632

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

110849001Z

Service Bulletin/Repair Instructions

This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.

PIP4902L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

050604022P

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

PIP5427B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P2635, U0074 and or U18A2. Technician will need to follow published diagnostics for Diagnostic Trouble Codes U0074 would take priority over U18A2 if both set before addressing DTC P2635.

060605001H

Service Bulletin/Repair Instructions

This informational bulletin explains the normal characteristics of exhaust noise during active fuel management when in Three or Four Cylinder Mode.

150601002H

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.

PIT5426B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician for a water leak in in the second and third row seating area. Inspect the C-pillar which is the body vertical structure behind the rear passenger door area of the affected side of the vehicle for water intrusion or water marks on the seat belt retractor. If water evidence is found on the seat belt webbing or the retractor the seat belt/ retractor must be replaced after the water leak has been corrected and verified. There are 3 areas of seam sealer that will need to be addressed. After gaining access to the C-pillar and rear quarter panel area inspect for voids or missing seam sealer and apply a clear flow able seam sealer where needed.

120089002C

Service Bulletin/Repair Instructions

This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.

PIT5390C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have the alarm sounding when learning new key fobs after the original key fobs were lost. Technician will open the driver's door and allow the Content Theft Deterrent alarm to activate, which will pulse the horns and exterior lamps for approximately 30 seconds and the alarm will shut off at this time. As long as the driver's door remains open the alarm will not turn back on and the new transmitters can be programmed.

PIT5552C

Service Bulletin/Repair Instructions

This Preliminary information communicates repair information for the rear vision camera or surround vision camera image being: -  Yellow -  Blurry -  Distorted -  Image scrolling -  Image with NO gridlines -  Screen is blue with gridlines -  Screen is blue with Service Rear Vision System message

PIP5337K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to refer to bulletin 16-NA-175 to aid in addressing torque converter clutch shudder concerns.

PIP5540D

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PIP5628

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

010310003R

Service Bulletin/Repair Instructions

This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.

PI0564K

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

090089016F

Service Bulletin/Repair Instructions

This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.

110849001Y

Service Bulletin/Repair Instructions

This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off.

16NA175

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or shudder during a light throttle acceleration between 40 and 128 KM/H (25 and 80 MPH) at a steady state.

PIP5554A

Service Bulletin/Repair Instructions

This Preliminary information communicates P0016 setting after internal engire repair. The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.

090089002P

Service Bulletin/Repair Instructions

This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.

PIT5307F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a service engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.

010089010M

Service Bulletin/Repair Instructions

This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).

080089014D

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

17NA346

Service Bulletin/Repair Instructions

This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs.

030603004X

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

PIE0500

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information to check the shutters through the grille opening of the vehicle. If snow and/or ice is present on the active grille air shutters, take pictures and submit through the Field Reporting Process.

17NA170

Service Bulletin/Repair Instructions

This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.

16NA339

Service Bulletin/Repair Instructions

This informational bulletin aids the technician on diagnosing possible vibrations in a vehicle, methods used for testing each scenario and documenting findings.

100089005H

Service Bulletin/Repair Instructions

This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.

PI1513F

Service Bulletin/Repair Instructions

This preliminary information bulletin provides a procedure for radiator and engine coolant thermostat replacement to eliminate coolant smell and/or a slight leak at the radiator.

040089015T

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on required operating procedures.

PIT5565B

Service Bulletin/Repair Instructions

This Preliminary information communicates a repair procedure for a squeak/squawk type noise coming from the lower column/drivers footwell area when turning.  It explains how to properly lubricate the column shaft boot where the shaft interacts with the boot where it passes through the boot.

060089026O

Service Bulletin/Repair Instructions

This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).

PIC6073E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.

PIT5214D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

17NA066

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow test.

010842001L

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.

080089014C

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).

PIT5479B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

18NA153

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the GEN I charging system with a GEN II charging system only if vehicles apply within the settings.

PIP5503A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being overfull on oil causing an engine vibration concern. The technician is advised to inspect for contaminnants and adjust the engine oil level as needed.

PIP5540B

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

000310003X

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

060847001N

Service Bulletin/Repair Instructions

This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.

060850009J

Service Bulletin/Repair Instructions

This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.

PIT5434C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician only to provide additional tips when diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information.  Always, perform and refer to Service Information for the latest diagnostic information and procedures.

18NA360

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the side mirror cameras if found the cause of the reduced key fob range.

PIP4925B

Service Bulletin/Repair Instructions

This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.

PIP5382K

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner's Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before doing any repairs to the vehicle.

PIT5350B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that there have been some reports that the current engine hours are not correct and display 0.0. Technician will need to program the Instrument Panel Cluster using Service Programming System.

PIT5353C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

PIP5298A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician for a Service Engine Soon light with a Diagnostic Trouble code P0300 set. There may be a rough running engine associated with this concern. If service information diagnostics have been completed and there is still no trouble found, the technician is to inspect for a possible terminal tension concern on the ignition coil power feed for the cause of the rough running engine and or the P0300.  For the Service Engine Soon light or traction control lamp concern check the X2 connector of the under hood fuse block for poor pin retention.

PIT5445C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician of additional information when diagnosing a service driver assist message with a diagnostic trouble code B172E and or a B172F. The haptic seat motor has a pigtail lead coming off of it. In many cases the wiring pigtail near the haptic seat motor has broken and will require replacement.

PIT3946C

Service Bulletin/Repair Instructions

This Preliminary Information communicates an issues with the headliner sagging and how to reattach the velcro using Hardman Double Bubble Epoxy part number 04001.

PIT5594A

Service Bulletin/Repair Instructions

This Preliminary information communicates a normal DIC message after learning keys/fobs which indicates the drivers memory position.

PIT5272B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a whistle noise in the vehicle from the driver or passenger side. Technician will need to inspect for voids in the body sealer on the left or right side A-pillar. Technician should also inspect for voids in the body sealer at the cowl seam and apply sealer as necessary.

PIP5609

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer an issue where the vehicle's service engine soon light may illuminate due to trouble codes P0601-P0604, P0606, P062B, P062F, P0630, P16F3, or P262B . The dealer is to inspect the engine control module's electrical connections and for proper powers and grounds. Dealer instructed to replace the Engine Control Module, if no other issues found.

PIC6086E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area.  Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.

PIP5159C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on and Diagnostic Trouble Code P0300 - P0308  may set. Technician will inspect for lose sparkplug wire. If a spark plug wire is found lose check for a missing ?C? clip on the wire end for the ignition coil. If the clip is missing replace the wire.

PIT5438E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.

PIT5550B

Service Bulletin/Repair Instructions

This Preliminary information communicates that an inoperative third row folding seat back may not fold down or up.  This information advises dealers on how the seat functions and also a common area where an open circuit may be found between the third row seat module and the seat position sensor.  It provides repair instructions if a concern is found with the circuits between the third row folding seat module and the seat back position sensor, as well as advising the dealer to look for bent/damaged seat recline mechanisms.

PIP5601

Service Bulletin/Repair Instructions

This Preliminary information communicates

PIT5392C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a detent / click with a feel of increased resistance when the accelerator pedal is about ¾ of the way. The new accelerator pedal design has a built-in detent position near the last 1/4 of pedal travel. Dealer should communicate to the customer this is a normal operating characteristic of the vehicle and no repair attempts should be performed.

PIT5099D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIP5491A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician when diagnosing intermittent circuit concerns to look at the connector for missing weather pack seals that could allow water intrusion into the connector and lead to corrosion on the terminals.

PIP5596

Service Bulletin/Repair Instructions

This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.

PIT5604A

Service Bulletin/Repair Instructions

This Preliminary information communicates if the liftglass will not open using keyless entry to verify Valet Mode is not enabled.

PIT4322J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

PIT5576B

Service Bulletin/Repair Instructions

This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.

PIT5361D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have issues were the customer will need increased effort to depress the brake pedal. Technician may find fluid in the brake booster and/or the booster vacuum line. Technician will need to replace Vacuum Pump, Brake Booster, Master Cylinder, Vacuum Pump Belt and the Vacuum Line between the booster and the pump.

PIT5241F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about customers that may request the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup or SUV when the vehicle was not ordered with the option. Dealer should advise the customer it cannot be added to the vehicle.

PIT5448D

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

PIP4902K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIP5304B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a “Service 4WD Message” displayed in the Driver Information Center. Technician may find Diagnostic Trouble Codes C0392 or C0396. Technician should check the terminal tension on the Transfer Case Control Module X1 connector. Technician should repair any terminal that have poor terminal tension.

17336-04

Service Bulletin/Repair Instructions

17336 04 - Special Coverage (Warranty Information Revised). On some vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.

18NA156

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the dehydrator to correct the condition of A/C Inoperative and/or Insufficient Cooling due to the seals going bad within the part.

PIP5163D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIT5624

Service Bulletin/Repair Instructions

This Preliminary information communicates a diagnostic tip for an issues with the heated and/or vented seats turning off and setting DTCU1524 because of a loss of voltage to the Seat Heating Control Module.

PIC6095C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.

PIT5535C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.

PIC5260B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIP5121C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have the oil pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (LV3), 5.3L (L83), 6.2L (L86) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.

PIT5232E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps to diagnose and repair the concern of the display is showing 32° F (0° C) after a battery or reprogramming a module. The outside temperature will begin to update if driven above 20 mph for at least 5 minutes. If the vehicle speed drops below 20 mph, the timer will reset and the display will stop updating. Once the display starts to update it may take several more minutes of driving above 20 mph for the display to fully update. Also if the vehicle is shut off for more than 8 hours the display will update when the ignition is turned on.

PIT5318E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on a concern of wind buffeting noise and/or water leak.Technician is to follow the steps to apply vibration control material between the sunroof roof bow and the roof sheet metal.

PIT5099C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIC5953D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

PIP5335B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.

PIP5498K

Service Bulletin/Repair Instructions

This Preliminary information communicates. A vehicle may have a concern ofDTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.

PIT5457C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the driver and passenger sill plate to gain access to the wire harness. If any open, damaged, or corroded wires should be repaired.

PIT5533B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.

PIT5565A

Service Bulletin/Repair Instructions

This Preliminary information communicates a repair procedure for a squeak/squawk type noise coming from the lower column/drivers foot well area when turning. It explains how to properly lubricate the column shaft boot where the shaft interacts with the boot where it passes through the boot.

PIT5622

Service Bulletin/Repair Instructions

This Preliminary information communicates instructions dealer to inspect for a broken or damaged side objector sensor/module bracket if there is a "Side Detection System Unavailable" message displayed at startup.

PIP5373B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. In some cases Techline Customer Support Center may need to be contacted to resolve the issue.

PIT5620

Service Bulletin/Repair Instructions

This Preliminary information communicates and issue with an itch, rattle, flutter, squeak, tick, and/or chirp type noise coming from the left I/Por A-pillar area caused by contact between the drivers fender and A pillar.

PIP5498J

Service Bulletin/Repair Instructions

This Preliminary information communicates. A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.

PIT5380C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have a front driver's or passenger's seat back may lean or be turned outward. Technician will need to remove the seat bottom trim cover and reinstall it completely and squarely to the cushion to correct the concern.

PIT5617

Service Bulletin/Repair Instructions

This Preliminary information communicates information to have dealers contact TCSC for programming assistance with new amplifier part numbers until all the new amplifier numbers are setup correctly for programming.

PIT5507E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and/or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.

PIT5399A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

PIT5509D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

PIP5498H

Service Bulletin/Repair Instructions

This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause: Coolant getting into the cylinders, and provides direction for the repair.

PIP5569

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.

17336 03

Service Bulletin/Repair Instructions

Special Coverage. Some vehicles may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.

18NA141

Service Bulletin/Repair Instructions

This informational bulletin provides information on Audio Volume Stuck High or Low with No DTCs and that this is a normal characteristic.

PIT3219E

Service Bulletin/Repair Instructions

This Preliminary Information communicates to techniciansthat the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49). These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.

PIT5308C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with the ignition off, Crank no start, Start and Stall, and vehicles equipped with the diesel engine, the blower motor may stay on after the engine is turned off. Technician may find Diagnostic Trouble Code P2537 and/or P129Dset. Technician will need to Use a voltmeter and check circuit 5985 at the Engine Control Module and Transmission Control Module. If no or low voltage is found, use the wiring diagram in Service Information and perform normal circuit diagnosis.

PIT5572A

Service Bulletin/Repair Instructions

This Preliminary information communicates aService Adaptive Cruise With DTC C018C SYM3A After Replacing K14 Distance Sensing Cruise Control Module and provides tips for completing all necessary steps and to contact TCSC if configuration does not complete correctly.

150603002M

Service Bulletin/Repair Instructions

This bulletin provides information on approved warranty part numbers for original equipment batteries.

1208132001E

Service Bulletin/Repair Instructions

This informational bulletin explains to the dealer how to cover a possible customers mistake when a fuse has been blown.

18NA125

Service Bulletin/Repair Instructions

This informational bulletin provides information for engine oil life monitor operation calculation.

PI0754C

Service Bulletin/Repair Instructions

This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal characteristic.

080730035C

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

150603002L

Service Bulletin/Repair Instructions

This informational bulletin provides information on approved warranty part numbers for original equipment batteries

PI0281G

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

PI0564J

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

130089010B

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program.

060089031E

Service Bulletin/Repair Instructions

This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.

110849001W

Service Bulletin/Repair Instructions

This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.

PIT5195D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

PIT5507D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.

010310003Q

Service Bulletin/Repair Instructions

This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.

PIT5311D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle’s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector with part number 23404450.

PIT5530B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory Accessory 22" Wheels Regular Production Option Code (SES, SEU, SEY, OR SEZ) or production 22" wheels Regular Production Option Code (RPT or SMI) also during any service requiring wheel removal.

000089027J

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on properly eliminating unwanted odors in vehicles.

18NA087

Service Bulletin/Repair Instructions

This informational bulletin provides information on Phantom Three Beeps or Horn Chirps Heard After Turning Off Vehicle and that it should be considered normal.

PIT5391D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.

110089002C

Service Bulletin/Repair Instructions

This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).

18NA079

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the drivers front door window regulator motor and door wiring harness if water and/or corrosion is found in the connectors.

030089006P

Service Bulletin/Repair Instructions

This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.

PI1091C

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides repair information to correct a customer concern of warm air exhausting from driver and/or passenger front seat back into 2nd row seating area causing occupant discomfort.

PIT5282D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).

17NA215

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar® Module Functionality After OnStar Module Replacement for Another Condition.

090604015C

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.

PIP5555A

Service Bulletin/Repair Instructions

This Preliminary information communicatesA vehicle has DTC P06DD setting. (This PI applies to vehicles that have either an original or replacement oil pump).The oil pump control solenoid may be damaged or broke.

PIP5555

Service Bulletin/Repair Instructions

This Preliminary information communicatesA vehicle has DTC P06DD setting. (This PI applies to vehicles that have either an original or replacement oil pump).The oil pump control solenoid may be damaged or broke .

090604026N

Service Bulletin/Repair Instructions

This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada

17NA214

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct customer concerns of OnStar, XM, GPS or antenna malfunction ? may set DTC B2462, B2470 or B125C - and/or water leak on headliner at sun visor or overhead console areas, possible battery drain concern.

18NA038

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the rear brake rotors to correct a condition of Squeak/Squeal Type Noise Heard at Low Speeds During Brake Apply due to moisture build up on the rotors.

110089005L

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.

PI1481B

Service Bulletin/Repair Instructions

This preliminary informational bulletin adds the 2016 model year and provides technicians with repair information to correct a customer concern of rough, uneven or irregular horizontal seam on liftgate.

PIT5049D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.

PIT5511B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure. This is done to protect the Driver Information Center from damage.

PIT5552B

Service Bulletin/Repair Instructions

This Preliminary information communicates repair information for therear vision camera or surround vision camera image being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message

PIP4670E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.

030603004W

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

060601010D

Service Bulletin/Repair Instructions

This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.

150603002K

Service Bulletin/Repair Instructions

This informational bulletin provides information on approved warranty part numbers for original equipment batteries

PIC5891E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative. Technician will need to toggle through all languages then back to the desired language.

150603001D

Service Bulletin/Repair Instructions

This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.

18NA027

Service Bulletin/Repair Instructions

This informational bulletin provides information retaining to the fact that Service Manuals will now be available on USB.

PIP5226B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

PIT3271H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIT5233D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have hard or unable to rotate ignition key concern. When the concern is present the steering wheel will need to be rotated in either direction to alleviate the pressure between the steering column lock pin and lock plate. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.

PIT5277D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have intermittent and hard to duplicate Rear Camera blank, distorted, or fuzzy. Also no radio, OnStar, or speech audio and the volume is unable to be adjusted from the integrated center stack or the steering wheel controls. The driver information center will show “No Audio” in Audio mode. Technician will need to inspect X275 and X225 for bent terminals, terminals backing out of the connector, or terminals contacting another terminal behind each side of the connector and repair as necessary.

PIP5540A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

100864002D

Service Bulletin/Repair Instructions

This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.

PIP5308B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with the Service Engine Soon Malfunction Indicator Lamp on. Technician should follow published Service Information diagnostics that will lead to an oil pump replacement. Technician should replace the oil pump. If debris is found, the main and rod bearings should be inspected before engine replacement is considered.

050851001I

Service Bulletin/Repair Instructions

This information bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.

PI0653E

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.

PIT5245C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the blower motor may be noisy or vibrate when running. This concern will only occur when the temperatures is below 32 degrees Fahrenheit and if the blower motor is removed while still cold, ice may be found on the blower motor cage. This concern could be caused by water leaking or snow ingestion into the Heater-Vent-Air Conditioning case. Technician is to perform normal water testing diagnostics while the Heater-Vent-Air Conditioning is running, looking for water leaking past the plenum cover. If water is leaking past the cover remove the cover and install a 12x12 snow resistant screen to the fresh air intake. Reseal and install the plenum cover cap using Kent air dry sealer or equivalent.

060089026N

Service Bulletin/Repair Instructions

This warranty bulletin provides labor operation numbers for customer concerns that cant be duplicated.

010310003P

Service Bulletin/Repair Instructions

This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.

PIP5540

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.

17NA074

Service Bulletin/Repair Instructions

This informational bulletin provides information and Tips for Customers Having Difficulty Launching Android Auto or Apple CarPlay.

050604022O

Service Bulletin/Repair Instructions

This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.

PIT5529A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have Trailer connection not recognized or “Check Trailer wiring” or “Service Trailer Brake” message. Technician may find Diagnostic Trouble Codes C1112, C1113, C1114, C111B, U1556, and/or U1505. Technician will need to inspect the battery and Trailer Brake Power Module connector for corroded terminals and replace as necessary.

PIT5576A

Service Bulletin/Repair Instructions

This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.

16NA061

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on how to correct tire pressure messages and dashes.

PIC5650D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

PIC5491K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

PIP4578B

Service Bulletin/Repair Instructions

This PI was superseded to update model years and add information concerning idle surge, reduced engine power mode, and/or DTCs P0068, P0121, P1516, P2101, P2119, and/or P2176 that may be experienced on high mileage vehicles. Please discard PIP4578.

PIT5354B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).

040089015R

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on required operating procedures.

16NA075

Service Bulletin/Repair Instructions

This Bulletin provides procedures to correct a condition of Power Foldaway Mirror Glass Shake, Flutter at Normal Driving Speeds

PIT5604

Service Bulletin/Repair Instructions

This Preliminary information communicates if the liftglass will not open using keyless entry to verify Valet Mode is not enabled.

PIT6504

Service Bulletin/Repair Instructions

This Preliminary information communicates if the liftglass will not open using keyless entry to verify Valet Mode is not enabled.

000310003W

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

PIE0416A

Service Bulletin/Repair Instructions

This engineering informational bulletin ends the need for information from the field on vehicles that have the condition of Malfunction Indicator Lamp Illuminated with DTCs P0335, P0340, or P0365 Set.

080730026E

Service Bulletin/Repair Instructions

This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

150601002F

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.

070089037L

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.

PIP5498E

Service Bulletin/Repair Instructions

This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.

120089007A

Service Bulletin/Repair Instructions

This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.

150603001C

Service Bulletin/Repair Instructions

This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.

PIT5341C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about owners that want the auto door lock disabled. There is no avalible setting or Body Control Module calibration to turn off the auto door locks.

PIC5839D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

150603002J

Service Bulletin/Repair Instructions

This informational bulletin provides information on approved warranty part numbers for original equipment batteries

070089036I

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on enhancing field product reports with digital pictures.

16NA239

Service Bulletin/Repair Instructions

This Bulletin provides a procedure to activate/enable 4G LTE Wi-Fi Hotspot on New vehicle.

17NA386

Service Bulletin/Repair Instructions

This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis.

150603002I

Service Bulletin/Repair Instructions

This informational bulletin provides information on approved warranty part numbers for original equipment batteries

010601011J

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

16NA356

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.

PIP5337J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 miles per hour steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will need to run the vehicle in three different operational modes. The three modes are Normal, torque converter clutch open, and torque converter clutch closed. Technician will need to press and hold the tow-haul mode button for five seconds to disable grade braking to prevent downshifts during test. Technician will need to duplicate the concern in Normal mode. If the concern is gone in torque converter clutch open and closed then the torque converter should be replaced. If the concern is not present in normal mode, torque converter clutch open, and torque converter clutch closed the concern is not with the shudder. Technician should use of the PICO scope and Noise, Vibration and Harshness software can be used to confirm torque converter clutch shudder, Engine, Tire or Driveline component related conditions. Flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool when the torque converter is replace.

16NA341

Service Bulletin/Repair Instructions

This technical bulletin provides multiple fixes for a condition of a waiting for update screen appearing on the display, due to either a reprogramming of the hmi module or due to a fuse that needs to be pulled and restarting of the module.

17NA344

Service Bulletin/Repair Instructions

This informational bulletin provides information for the technician when looking up the P/N for the 3.5 mm audio jack for the USB, to make sure and enter the VIN# to ensure the correct part is being ordered.

PI1149A

Service Bulletin/Repair Instructions

This preliminary information bulletin provides a procedure on how to check for the customer concern of a blank radio with/without audio, by checking the the wiring harness, ECU and reprograming the HMI software update, if the wiring or ECU are not the cause.

PIC6235A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the navigation system will be unable to enter addresses that contain diacritics using the touch screen. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

16NA389

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to reprogram the FVCM if the battery has issues that are related to the front camera module.

17NA142

Service Bulletin/Repair Instructions

This informational bulletin provides information on Wireless Charging Module Diagnosis and cell phone compatibility.

040730013D

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.

16NA158

Service Bulletin/Repair Instructions

This bulletin describes the Dealer special tool loan program process.

17NA375

Service Bulletin/Repair Instructions

This informational bulletin provides a diagnostic tip for rear vision camera image that is grainy, distorted and/or pixelated

15NA082

Service Bulletin/Repair Instructions

This technical bulletin provides repair information for installing a new stabilizer shaft bracket to correct a customer concern of on a clunking noise originating from the front of the vehicle that is more predominant during turns or traveling over bumps.

PIT4261E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

PIT5434B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician only to provide additional tips when diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures.

PIT5599

Service Bulletin/Repair Instructions

This Preliminary information communicates a false setting of DTCU0121 in the FVCM due to a FVCM software anomaly. Code U0121 will set and be moved to history in the FVCM with each ignition cycle.

070604019F

Service Bulletin/Repair Instructions

This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.

17NA297

Service Bulletin/Repair Instructions

This informational bulletin provides information for assisting the customer in setting the position for the memory mirror and the reverse tilt

PIT5202D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission, now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.

PIC3100F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

PIT5291C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have wind whistle noise heard from the right or left rear quarter glass area when driving at highway speeds or with a cross wind. Technician will inspect the quarter glass for excessive urethane. If excessive urethane is found use a sharp knife and cut off the excessive urethane. Also the technician will install foam tape along the entire length of the tail light assembly.

PIT5379D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a content theft alarm sounding for no apparent reason. Technician may use all published Service Information diagnostics and has not found the cause of the unwanted content theft alarm sounding. Technician should use Global Diagnostic System 2 to review the Body Control Module parameters for "Content Theft Deterrent Trigger History". If the trigger is an Intrusion inspect for items hanging from the rear view mirror, solar powered dancing characters. When the trigger is a Glass breakage inspect the two rear quarter-panel windows and also in the liftgate glass. The quarter panel windows are attached to the body harness with a connector that looks similar to a 9 volt battery connector inspect them to be fully seated in on the glass. When the trigger is Ignition Voltage/Battery reconnect detected during a cold ambient temperature remote vehicle start event technician should call GM General Motors Technical Assistance Center.

PIT5594

Service Bulletin/Repair Instructions

This Preliminary information communicates a normal DIC message after learning keys/fobs which indicates the drivers memory position.

17336 02 (Bullet

Service Bulletin/Repair Instructions

17336 02 - Special Coverage (Parts and Service Procedure Revised). On some vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.

17336-02

Service Bulletin/Repair Instructions

On some 2015-2017 model year Cadillac Escalade, Escalade ESV, Chevrolet Suburban, Tahoe, GMC Yukon and Yukon XL vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance

PIT3946B

Service Bulletin/Repair Instructions

This Preliminary Information communicates an issues with the headliner sagging and how to reattachthe velcrousing Hardman Double Bubble Epoxy part number 04001.

17NA337

Service Bulletin/Repair Instructions

This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu.

17NA335

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the fuel pump to correct the MIL concerns.

PIP5411F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have hesitation or a stalling condition while in ambient temperatures 100 degrees or higher. Technician may find Diagnostic Trouble Codes P2635 and or P018B set. The dealer is advised to replace the in tank fuel pump module assembly to correct the condition.

PIP5411E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have hesitation or a stalling condition while in ambient temperatures 100 degrees or higher. Technician may find Diagnostic Trouble Codes P2635 and or P018B set. The dealer is advised to replace the in tank fuel pump module assembly to correct the condition. Dealer directed to follow latest version of PIP5507 if the fuel pump does not correct the concern.

PIC5492F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.

PIT5353B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

PIT5533A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.

070849020M

Service Bulletin/Repair Instructions

IPC Odometer Programming Method Quick Reference Guide

140089004D

Service Bulletin/Repair Instructions

Information for Fleet Vehicles – Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple keys, fobs, and key tags together on a single crimped loop or a cable. This practice may result in unintended key rotation, and should be discontinued immediately. The information in this bulletin details the proper configurations for the ignition key, fob, key rings and key tags and applying a QR code sticker or barcode sticker to a key fob.

150089004B

Service Bulletin/Repair Instructions

Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component

150089005A

Service Bulletin/Repair Instructions

Essential Tools that Include Consumable Parts (U.S. Only)

150603002H

Service Bulletin/Repair Instructions

Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Access to the battery specification label, which contains the OEM part number and CCA rating and type, may be difficult without component removal. Refer to the table below for the original equipment ratings and part numbers used to set up a proper battery test. There has been some confusion as to the correct ACDelco battery warranty replacement. Refer to the table below for the correct battery warranty replacement. The correct ACDelco battery warranty replacement in the catalog is designated by the "Original Equipment Replacement" note in the description field.

16-NA-175

Service Bulletin/Repair Instructions

SHAKE AND/OR SHUDDER DURING LIGHT THROTTLE ACCELERATION BETWEEN 40 AND 128 KM/H (25 AND 80 MPH) AT A STEADY STATE.

17-NA-337

Service Bulletin/Repair Instructions

All or Some Options May Be Missing from Driver Information Center (DIC) “Info Pages” Menu Due to Them Not Being Selected Condition Some customers may comment that with the “Info” option selected from the main menu (1), the “Info Pages” are blank (2) when scrolling up and down. If information is present when scrolling up and down, they may also comment that certain items are missing when compared to other like vehicles Cause This condition may be caused when all/some of the options not being selected in the “active info pages” menu. Correction If this concern is encountered, determine if all/any of the selections in the “active info pages” menu are not selected. To do this, follow the steps listed below.

PIT5236K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.

PIT5585

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that will have an intermittent pop noise from the speakers followed by a reset of the radio and clock. Technician will need to check for Diagnostic Trouble Codes and also check the battery for proper cable connections. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

PIP5382J

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner’s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before doing any repairs to the vehicle.

PIT5521A

Service Bulletin/Repair Instructions

This preliminary information communicates a Diagnostic Tip for a Service Trailer Brake Message with DTC C111B C1112 C1113 C1114 advising to address any battery issues first before any in depth diagnostics are done.

030603004V

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

PIP4723C

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIT5074K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIT5350A

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that there have been some reports that the current engine hours are not correct and display 0.0. Technician will need to program the Instrument Panel Cluster using Service Programming System.

PIT5403D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

PIT4322H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

PIT5241E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about customers that may request the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup or SUV when the vehicle was not ordered with the option. Dealer should advise the customer it cannot be added to the vehicle.

040601029I

Service Bulletin/Repair Instructions

This informational bulletin explains the importance of maintaining the vehicle.

100089005G

Service Bulletin/Repair Instructions

This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.

PI1513E

Service Bulletin/Repair Instructions

This preliminary information bulletin provides a procedure for radiator and engine coolant thermostat replacement to eliminate coolant smell and/or a slight leak at the radiator.

000601012H

Service Bulletin/Repair Instructions

This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

PIT5389E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

150603002G

Service Bulletin/Repair Instructions

This informational bulletin provides information on approved warranty part numbers for original equipment batteries

PIT3099Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.

070601016D

Service Bulletin/Repair Instructions

This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

00-06-01-026J

Service Bulletin/Repair Instructions

This informational bulletin provides information on Intake Manifold Inspection/Replacement After Severe Internal Engine Damage.

13-08-116-001C

Service Bulletin/Repair Instructions

The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

PIC6296A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2. Technician should not replace the Human Machine Interface for this concern, power cycling of the Human Machine Interface fuse should restore communication. Technician should be advised that the Human Machine Interface and Global Diagnostic System 2 interaction concern has been reported to engineering for root cause and correction.

99-08-51-001D

Service Bulletin/Repair Instructions

Thins informational bulletin provides information on Paint-less Dent Repair Process.

PIT5301B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that Diagnostic Trouble Code B127E in the Human Machine Interface with Regular Production Option Code U42 or UWG will be current when playing a DVD or Blu-Ray on the Integrated Center Stack display. When the disc is ejected the Diagnostic Trouble Code will be history. If the Diagnostic Trouble Code B127E remains current after ejecting the disc follow Service Information diagnostic procedure instructions for B127E with Regular Production Option Code U42 or UWG.

PIP5163C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIT5452B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a pop, click, tick, snap, or itch type noise in the steering column or steering wheel when turning left or right during low speeds or parking maneuvers. Technician will need to inspect for mis-routed airbag module wiring harness for contacting vibration damper plate in steering wheel, orreplace the column upper bearing inner race, spring, and seat.

PIP5427A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P2635, U0074 and or U18A2. Technician will need to follow published diagnostics for Diagnostic Trouble Codes U0074 would take priority over U18A2 if both set before addressing DTC P2635.

PIE0428

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information from the field on vehicles that have the condition of the steering wheel jerks, whips or kicks back when turning.

PIT5579

Service Bulletin/Repair Instructions

This Preliminary information communicates that a tick, creak or rattle noise may be heard while driving the vehicle. This noise may be caused by insufficient or missing spot welds on body panels or contact between body panels at the "B" or "C" pillars. The technician is instructed on how to determine the source of the noise and then repair it by replacing the spot welds or slightly separating the panels depending on the exact condition.

PIC5932B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.

04-00-89-015Q

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on required operating procedures.

16-NA-111

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to perform diagnosis before just replacing the battery sensor module.

08-08-44-029H

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.

04-00-89-015P

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on required operating procedures.

11-08-49-001V

Service Bulletin/Repair Instructions

This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.

17-NA-244

Service Bulletin/Repair Instructions

This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.

PI1091B

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides repair information to correct a customer concern of warm air exhausting from driver and/or passenger front seat back into 2nd row seating area causing occupant discomfort.

PIT5392B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a detent / click with a feel of increased resistance when the accelerator pedal is about ¾ of the way. The new accelerator pedal design has a built-in detent position near the last 1/4 of pedal travel. Dealer should communicate to the customer this is a normal operating characteristic of the vehicle and no repair attempts should be performed.

17-NA-242

Service Bulletin/Repair Instructions

This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to reprogram modules that have been already reprogrammed.

03-03-10-007J

Service Bulletin/Repair Instructions

This informational bulletin provides information on the temporary tire flat spotting condition.

16-NA-042

Service Bulletin/Repair Instructions

This informational bulletin provides information on GM offering the Android Auto feature upgrade for 2016 and 2017 model year vehicles and how to proceed with reprogramming the vehicles to include this application for use.

PI1385A

Service Bulletin/Repair Instructions

This informational bulletin provides information that the TPM sensors must always be relearned when accessory wheels are installed on the vehicle.

PIP5507B

Service Bulletin/Repair Instructions

This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.

PI0564I

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

PIC6086D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.

PIP5411D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have hesitation or a stalling condition while in ambient temperatures 100 degrees or higher. Technician may find Diagnostic Trouble Codes P2635 and or P018B set. The dealer is advised to replace the in tank fuel pump module assembly to correct the condition. Dealer directed to follow latest version of PIP5507 if the fuel pump does not correct the concern.

PIC5611E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.

PIP5507A

Service Bulletin/Repair Instructions

This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.

PIT5308B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with the ignition off, Crank no start, Start and Stall, and vehicles equipped with the diesel engine, the blower motor may stay on after the engine is turned off. Technician may find Diagnostic Trouble Code P2537 and/or P129Dset. Technician will need to Use a voltmeter and check circuit 5985 at the Engine Control Module and Transmission Control Module. If no or low voltage is found, use the wiring diagram in Service Information and perform normal circuit diagnosis.

15-NA-002

Service Bulletin/Repair Instructions

This bulletin provides repair information to correct a customer concern of fuel odor, fuel leaks from UH SIDI Pipes between High Pressure Pump and Fuel Rails

PIT5535B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.

PIT5576

Service Bulletin/Repair Instructions

This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.

PIT5564A

Service Bulletin/Repair Instructions

This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set.

PIP5507

Service Bulletin/Repair Instructions

This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.

PIP5503

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being overfull on oil causing an engine vibration concern. The technician is advised to inspect for contaminnants and adjust the engine oil level as needed.

PIT5404D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming. Replace or repair any of the issue that was found in the inspection.If the vehicle is equipped with a 4.3 liter or 5.3 liter engine an updated exhaust system is now available.

PIC6287

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the radio will not retain the previous settings and will go to the Home Icon screen when the vehicle is restarted. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.

PIP5330B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.

PIC5588D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

PIT5509C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

PIT3099P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

16-NA-389

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to reprogram the FVCM if the battery has issues that are related to the front camera module.

PIE0376A

Service Bulletin/Repair Instructions

This engineer informational bulletin ends the need for information from the field on vehicles that have the condition of Check Engine Light Illuminated and DTC P0751 Set on Vehicles Under 5,000 Miles.

00-03-10-002K

Service Bulletin/Repair Instructions

This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.

PI1410B

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on.

00-06-01-012G

Service Bulletin/Repair Instructions

This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces.

05-00-89-029D

Service Bulletin/Repair Instructions

This informational bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.

PI0020E

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides technicians with information on the normal condition of white, milky or cloudy appearance of front differential fluid.

03-00-89-006N

Service Bulletin/Repair Instructions

This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.

17-NA-153

Service Bulletin/Repair Instructions

This informational bulletin provides information and operating tips for the hands free lift gate.

04-00-89-015O

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on required operating procedures.

17-NA-142

Service Bulletin/Repair Instructions

This informational bulletin provides information on Wireless Charging Module Diagnosis.

11-00-89-005K

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.

PI1513D

Service Bulletin/Repair Instructions

This preliminary information bulletin provides a procedure for radiator and engine coolant thermostat replacement to eliminate coolant smell and/or a slight leak at the radiator.

PI1513C

Service Bulletin/Repair Instructions

This preliminary information bulletin provides a procedure for radiator and engine coolant thermostat replacement to eliminate coolant smell and/or a slight leak at the radiator.

PIT5447B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps needed to diagnose and repair vehicles that may have a rattle noise from the dash. Technician will need to inspect for the rear heater pipes contacting the passenger side exhaust manifold. If the rear heater pipe is found to be contacting the exhaust manifold, reposition the heater pipe so it no longer makes contact.

17-NA-126

Service Bulletin/Repair Instructions

This informational bulletin provides information on Non-Design Intent Wheel Lock Nuts and Lug Nuts.

16-NA-355

Service Bulletin/Repair Instructions

this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.

PI0281F

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

PIT5457B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the driver and passenger sill plate to gain access to the wire harness. If any open, damaged, or corroded wires should be repaired.

10-08-110-001F

Service Bulletin/Repair Instructions

This informational bulletin provides information on proper use of floor mats.

03-06-03-004U

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

15-06-03-002F

Service Bulletin/Repair Instructions

This informational bulletin provides information on approved warranty part numbers for original equipment batteries

PIP5369B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have "Service 4 Wheel Drive" message on the Driver Information Center. Provides the technician with additional information to ensure that the TCCM contains the latest software released to address previous issues, also advises of default action changes. Calls out specific circuits to be inspected to help isolate intermittent codes.

PIP5491

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician when diagnosing intermittent circuit concerns to look at the connector for missing weather pack seals that could allow water intrusion into the connector and lead to corrosion on the terminals.

99-04-20-002J

Service Bulletin/Repair Instructions

This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.

PIP4112R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

16-NA-339

Service Bulletin/Repair Instructions

This informational bulletin aids the technician on diagnosing possible vibrations in a vehicle, methods used for testing each scenario and documenting findings. This technical bulletin provides a procedure to install dust deflectors when replacing wheel bearings on vehicles no matter what the concern is of the vehicle. This technical bulletin provides a procedure to reprogram the TRCM to correct the customers concern of the Service Transmission and MIL on. This technical bulletin provides a procedure to reprogram the FVCM if the battery has issues that are related to the front camera module.

PI0671A

Service Bulletin/Repair Instructions

This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid reservoir.

16-NA-412

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to reprogram the ECM to correct multiple transmission concerns.

PIT5507C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.

PIT5509B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

17-NA-067

Service Bulletin/Repair Instructions

This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.

06-08-47-001M

Service Bulletin/Repair Instructions

This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.

17-NA-025

Service Bulletin/Repair Instructions

This technical bulletin is providing a procedure to reprogram the HMI module to correct multiple conditions including Waiting for Update Media Message, Voice Command For Calling Bluetooth Phone Contacts Inoperative, Intermittent Loss of Rear Camera Gridlines, Service Rear Vision System Message, Radio Turns On Unwanted At Startup, and/or Navigation Radio Destination State Defaults To WV, Intermittent Radio/display Resets, Volume Control Inoperative.

10-00-89-006F

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers how to submit a product information report.

PIT5389C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

PIC4935F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.

PIT5390A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have the alarm sounding when learning new key fobs after the original key fobs were lost. Technician will open the driver’s door and allow the Content Theft Deterrent alarm to activate, which will pulse the horns and exterior lamps for approximately 30 seconds and the alarm will shut off at this time. As long as the driver’s door remains open the alarm will not turn back on and the new transmitters can be programmed.

PIP4723B

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIT5426A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician for a water leak in in the second and third row seating area. Inspect the C-pillar which is the body verticalstructure behind the rear passenger doorarea of the affected side of the vehicle for water intrusion or water marks on the seat belt retractor. If water evidence is found on the seat belt webbing or the retractor the seat belt/ retractor must be replaced after the water leak has been corrected and verified. There are 3 areas of seam sealer that will need to be addressed. After gaining access to the C-pillar and rear quarter panel area inspect for voids or missing seam sealer and apply a clear flow able seam sealer where needed.

GCUS-3-848

Service Bulletin/Repair Instructions

44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.

PIC3278G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

PIC4801H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.

PIC5959C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.

PIC5588C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

02-00-89-002Q

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.

01-03-10-003O

Service Bulletin/Repair Instructions

This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.

PIP5029H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.

PIP5338A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.

PIT5049C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.

PIP4902J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

PIC6086C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.

PIT5287C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.

PIT5380B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have a front driver's or passenger's seat back may lean or be turned outward. Technician will need to remove the seat bottom trim cover and reinstall it completely and squarely to the cushion to correct the concern.

PIT5405C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a reduced or loss of power steering assist, steering wheel jerks or kicks back when turning, Service Stabilitrak message with warning chime, engine stall, Instrument Panel Cluster going blank or inoperative, radio/Integrated Center Stack going blank, Heater-Vent-Air Conditioning going blank, hood ajar message and/or dome lamps flash when shifting into reverse, alarm sounds when locking doors or door locks cycling, and or wipers continue to run for a short time after turning off and then stop/park in the incorrect location. Technician may find Diagnostic Trouble Codes U0073, U0078, U0029, U0028, U0415, U0140, U0126, U0121, U0101, U0100, C0544, C0710, U1510, B127B, B2605, B3600, C0800, U0428, U0452, U0131, and P0513 set in the vehicle. Check the body control module ground at the G218 location. The front dash insulator mat may be trapped between the ground eyelet and the body stud. Remove the round nut and eyelet and cut the front dash insulator mat away from the ground stud so it no longer interferes with the ground stud and reinstall the eyelet and ground nut. Technician will also inspect the starter solenoid battery cable for shorting out on the starter heat shield. Technician will need to voltage drop the battery cables. The battery should be tested using the GR8. X183 or X133 should be inspected for any broken/loose/backed out terminals.

PIT5543

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a dead battery after sitting for more than 20 days. Technician will need to change Rear Heated Seat Control Module power circuit 5140 from a hot-at-all-times fuse to a hot-in-run/crank fuse.

GCUS-3-823

Service Bulletin/Repair Instructions

17018-Customer Satisfaction Program. Certain vehicles, equipped with power front passenger seat adjuster that was previously replaced, may have a condition in which the front passenger seat can be adjusted to a position beyond the occupant design travel range. Dealers will inspect front passenger seat tracks and, as necessary, install the seat stop(s).

PIT5509A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System" message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

15-06-03-002E

Service Bulletin/Repair Instructions

This informational bulletin provides information on approved warranty part numbers for original equipment batteries

PIT5295C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the step to diagnose and repair vehicles with a CD or DVD player that will not take a disc. Technician will gain access to the player and inspect the player to be mounted on the locating pins. If the player is not mounted on the location pins reinstall the player.

PIT5542

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an excessive lateral driver or passenger seat movement and/or a clunk/click/pop type feeling or noise. Technician will need to install a front seat lateral retainer. Technician will need to remove plastic material from the top side of the guide end of the lateral retainer to enable installation.

PIT5448C

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

16-NA-411

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to reprogram the ECM and TCM to correct multiple transmissions concerns.

08-03-10-006F

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)

GCUS-3-814

Service Bulletin/Repair Instructions

44180 01 - Customer Satisfaction - Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.

11-08-49-001U

Service Bulletin/Repair Instructions

This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.

03-08-46-004S

Service Bulletin/Repair Instructions

This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.

PIC5759B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.

PIP3119N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster  Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.

PIT4733K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.

PIT5233C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have hard or unable to rotate ignition key concern. When the concern is present the steering wheel will need to be rotated in either direction to alleviate the pressure between the steering column lock pin and lock plate. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.

99-00-89-019O

Service Bulletin/Repair Instructions

This informational bulletin provides information for the (GWM) and (WPC) on parts return program.

PIC6177C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with information on vehicles with navigation radio Regular Production Option Code IO6 or UY4 that defaults to West Virginia instead of Virginia on a manual entry. General Motors engineering is currently working on a solution for this concern.

PIT5236J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to ensure campaigns 14395 or 15086 are completed. Technician will need to use Global Diagnostic System 2 and gather information and contact General Motors Technical Assistance Center for further assistance.

PIC6216C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and repair any phones that were deleted.

PIC6220A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with an intermittent loss of gridlines in the rear camera display screen and a "Service Rear Vision System" message that both happen at the same time. Technician should check for Diagnostic Trouble Codes and follow published Service Information diagnostics for the Diagnostic Trouble Codes. If not Diagnostic Trouble Codes stored and the concern was duplicated or the customer described the concern, dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.

PIT5311C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle?s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector with part number 23404450.

PIT5530A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory Accessory 22" Wheels Regular Production Option Code (SES, SEU, SEY, OR SEZ) or production 22" wheels Regular Production Option Code (RPT or SMI) also during any service requiring wheel removal.

07-08-49-020L

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

PIC6186F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

GCUS-3-804

Service Bulletin/Repair Instructions

28770 - SUB A ?Service 4WD? message may be displayed on the Driver Information Center and DTC C0398 may be set. Concurrently, the vehicle is permanently locked in 4HI and cannot be shifted shift out of it while the code is present. If the code is cleared, this scenario may repeat if the transfer case is in ?Auto? mode and driven for approx. 2 or more hours. Customers will likely notice that the steering wheel is harder to turn, the engine will feel like it has lost power and the tires may squeal when turning in a parking lot. Dealers are to reprogram the transfer case.

PIP5330A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.

PIT5477A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a squeak, clunk, or knock type noise from the front suspension when hitting bumps. Technician will need to test drive the vehicle to duplicate the concern. Check the upper strut mount area with chassis ears verifies that the noise is noticeable in that area. Technician will replace the jounce bumpers with part number 8457475.

PIT5411G

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.

PIP4138P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

PIP5337H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 miles per hour steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will need to run the vehicle in three different operational modes. The three modes are Normal, torque converter clutch open, and torque converter clutch closed. Technician will need to press and hold the tow-haul mode button for five seconds to disable grade braking to prevent downshifts during test. Technician will need to duplicate the concern in Normal mode. If the concern is gone in torque converter clutch open and closed then the torque converter should be replaced. If the concern is not present in normal mode, torque converter clutch open, and torque converter clutch closed the concern is not with the shudder. Technician should use of the PICO scope and Noise, Vibration and Harshness software can be used to confirm torque converter clutch shudder, Engine, Tire or Driveline component related conditions. Flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool when the torque converter is replace.

PIT5507B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.

PIP5252A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the engine may run hot with the snow plow installed. Do not exceed 64 kilometers per hour / 40 miles per hour with a snow plow mounted to the vehicle even if equipped with VYU. The vehicle could overheat and be damaged.

08-08-44-015H

Service Bulletin/Repair Instructions

This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs

PIE0381A

Service Bulletin/Repair Instructions

This engineering informational bulletin is ending the need for information from the field on vehicles that have the condition of rear auxiliary a/c not cooling or blowing warm air.

99-00-89-019N

Service Bulletin/Repair Instructions

This informational bulletin provides information for the (GWM) and (WPC) on parts return program.

PIT5533

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.

PIT5535

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.

PIC5492E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.

PIC6235

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the navigation system will be unable to enter addresses that contain diacritics using the touch screen. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

PIT5391C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.

PIT5472A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are equipped with Hands Free Power Lift-gate Regular Production Option Code (TC2). Some customers may experience problems with the activation of the lift-gate hands free operation. Dealer will communicate to the customer some tips on the Hands free Lift-gate. The remote keyless entry FOB must be within 3 feet or 1 meter from the bumper. The foot kick is conducted at the direct center of the length of kick zone.

PIT5481A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Starting with 2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded

01-03-10-003N

Service Bulletin/Repair Instructions

This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.

05-03-08-002H

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.

02-00-89-002P

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.

16-NA-364

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on how to test and perform a clutch learn procedure to correct delayed clutch engagement.

05-00-89-055F

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill procedures.

PIT5532

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a squeak or chirp type noise from the rear of the vehicle. Technician should use the latest version of PI1201. If the noise is gone replace the muffler and tail pipe assembly.

PIC6216B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and re-pair any phones that were deleted.

PIP5446

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.

PIT5288E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.

PIT5317A

Service Bulletin/Repair Instructions

This Preliminary information communication provides information to the technician about vehicles with the rear body fuse block with a loose fuse connection. Technician will need to check terminal tension on the rear fuse block. Technician will need to replace the rear body fuse block if poor terminal tension is the issue. Technician will need to replace the appropriate terminated lead if something other than the main power buss bar has poor terminal tension.

PIT5341B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about owners that want the auto door lock disabled. There is no avalible setting or Body Control Module calibration to turn off the auto door locks.

PIT5438C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.

PIT5530

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory 22" 6-Spoke Split Chrome Wheels Regular Production Option Code (SEU) or during any service requiring wheel removal.

PIE0359A

Service Bulletin/Repair Instructions

This engineering information bulletin is ending the need for information on vehicles with the condition of Vehicle Crank with No Start or Stalling with DTC P0011 and/or P00C6 Set.

PIT5354A

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician how determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).

PI1286B

Service Bulletin/Repair Instructions

This preliminary informational bulletin adds the 2016 model year to repair information to correct a customer concern of the hood fluttering, vibrating or displaying visible motion at highway speeds or over rough road surfaces.

PIT3099N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

PIT5434A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician only to provide additional tips when diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures. Trucks equipped with heated and cooled seats Regular Production Option Code (KB6), may comment on any of the following front heated seat concerns. Condition 1, a front heated seat (back and/or cushion) is inoperative. Technician should diagnosis each affected seat heater individually. Technician should test all four circuits Power, Ground, Control (from Body Control Module) and Heating Element Supply Power. The Power, Ground, Control (from Body Control Module) can easily be checked by starting the engine and turn on the cooled seat. When the cooled seats are turned on the blower in each seat back and cushion will turn on at that point technician will be able to hear the blower moving. The heating element supply power circuit can be test by disconnecting the affected heating element and connect a voltmeter across the heating element supply power and ground circuit. Then start the engine and turn on the heated seat, the blower will supply system voltage on the element supply power circuit for 1 to 2 seconds. With the heated seat element disconnected, use an ohmmeter to measure the resistance of the heating element. If all of the above steps check ok or the heating element resistance is close to the approximate spec, reconnect all disconnected connectors. Connect a voltmeter across the affected heated seat element connectors supply power and ground circuits back probing the connector. Then check the resistance of the heating element. The resistance should be close to the same resistance as when testing with the connector unplugged. Now check the voltage with the engine running and the heated sets on high. Condition 2, the front heate

16-NA-014

Service Bulletin/Repair Instructions

Delayed Engagement After Sitting With Engine Off - Torque Converter Fluid Drain Back

PIP5337G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 miles per hour steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will need to run the vehicle in three different operational modes. The three modes are Normal, torque converter clutch open, and torque converter clutch closed. Technician will need to press and hold the tow-haul mode button for five seconds to disable grade braking to prevent downshifts during test. Technician will need to duplicate the concern in Normal mode. If the concern is gone in torque converter clutch open and closed then the torque converter should be replaced. If the concern is not present in normal mode, torque converter clutch open, and torque converter clutch closed the concern is not with the shudder. Technician should use of the PICO scope and Noise, Vibration and Harshness software can be used to confirm torque converter clutch shudder, Engine, Tire or Driveline component related conditions. Flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool when the torque converter is replace.

PIP5163B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIP5437A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have harsh concerns. Technician are advised to use GDS2 software to confirm which shift is causing the concern. On low mileage vehicles technician are instructed to perform a drive learn procedure. On higher mileage vehicles technicians are instructed to remove the transmission fluid pan and inspect for debris. If debris is found technicians should disassemble and inspect for root cause of the concern and repair the transmission as needed. If no debris is found technicians are advised to replace the valve body.

PIP5442

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an exhaust leak, noisy exhaust, or noise mid-vehicle. Technician will need to check for an unseated pipe to pipe mid-joint connection. Technician will need to install new exhaust band.

11-00-89-004B

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on the change in product field action customer reimbursement procedure.

PIE0388

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information from the field on vehicles that have the condition of a MIL or a engine misfire due to a loose spark plug wire.

06-08-64-001D

Service Bulletin/Repair Instructions

This Informational bulletin describes warranty part reviews where door glass had chips or scratches.

16-NA-107

Service Bulletin/Repair Instructions

This Technical Bulletin provides a fix to reprogram the radio for vehicles that may experience any of the following conditions: DTC U0184 Set, Radio Inoperative, Blue Screen, AM Clipping Noise, HD On/Off Status Not Retained in Stations, Time Lag on Transitions, No Audio with Internal Amp, Park Assist Symbol Position Wrong in Rear View Camera

01-03-10-003M

Service Bulletin/Repair Instructions

This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.

PIP5437

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have harsh shifts concerns. Technicians will use Global Diagnostic System 2 software to confirm which shift is causing the concern. On low mileage vehicles technician are instructed to perform a drive learn procedure. On higher mileage vehicles technicians are instructed to remove the transmission fluid pan and inspect for debris. If debris is found in the pan, technicians should disassemble and inspect for root cause of the concern and repair the transmission as needed. If no debris is found technicians are advised to replace the valve body.

00-03-10-003V

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

11-08-49-001T

Service Bulletin/Repair Instructions

This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.

PIT5389B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.

04-06-04-051E

Service Bulletin/Repair Instructions

This informational bulletin provides information for maintenance cleaning of the fuel injectors.

04-06-04-051D

Service Bulletin/Repair Instructions

This informational bulletin provides information for maintenance cleaning of the fuel injectors.

PIC6177B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with information on vehicles with navigation radio Regular Production Option Code IO6 or UY4 that defaults to West Virginia instead of Virginia on a manual entry. General Motors engineering is currently working on a solution for this concern.

PIC6186E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

PIP5382F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner?s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before you contacting General Motors Product Quality Center.

040604051D

Service Bulletin/Repair Instructions

This informational bulletin provides information for maintenance cleaning of the fuel injectors.

PIP5211F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated ? continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active ? Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track l

16NA125

Service Bulletin/Repair Instructions

This informational bulletin provides information to replace the propeller shaft if technicians find a broken propeller shaft or U-joint due to different causes.

PIC6201A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with the steps needed to diagnose and repair a vehicle with Wi-Fi or Bluetooth inoperative or poor performance concern. Technician will need to obtain data from Global Diagnostics Services 2 and call General Motors Technical Assistance Center for further assistance. Technician should be advised that concern only applies to OnStar Wi-Fi Regular Production Option Code (VV4) and Bluetooth Regular Production Option Code (UPF).

PIT5236H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.

150603002D

Service Bulletin/Repair Instructions

Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers

PIT5284C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have a rattle noise from the second row seat. Technician will need to inspect the striker not aligned properly in latch opening. To repair this condition, rework/adjust the striker in the direction to center it in the latch opening. An adjustable wide mouth metal working tool may be used to adjust the striker just enough to center in the latch opening. Technician may find a seat bottom latch may have an unequal latch opening side-to-side for the striker to seat into. To repair this condition, with the affected seat in the tumbled forward position, while applying steady, firm pressure, cycle the seat down into the latched position. Some vehicles built prior to 09/21/2015 with 60/40 Split Bench Seat may have 60-percent long side bench, inboard latch may not be properly aligned in striker opening. Technician will need to place a 2.6 mm thick flat washer over the 40 percent seat base stud, not the floor stud. Some vehicles may have a seat base plat that rattles against the rib in the floor pan. Apply Mylar tape to the floor pan under the seat plate to provide relief for the rattle condition.

150603002C

Service Bulletin/Repair Instructions

This informational bulletin provides information on approved warranty part numbers for original equipment batteries

16NA355

Service Bulletin/Repair Instructions

this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.

PIT5307E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a service engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.

PIC6216A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and repair any phones that were deleted.

PIP5337F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 mph steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will drive the vehicle and monitor the torque converter clutch slip. The torque converter clutch slip speed should be 10 rpm or less also note if the shudder takes place during torque converter clutch apply. If the torque converter clutch slip speed is in the range of 10 RPM or less the condition is possibly related to engine performance. If the shudder is only present in 4 cylinder mode and torque converter clutch slip is 10 rpm or less deem the shudder concern normal characteristic of Active Fuel Management. If the slip speed is beyond 10 rpm or there is shudder during torque converter clutch apply the torque converter will need to be replaced. Also flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool.

GCUS-3-718

Service Bulletin/Repair Instructions

16046 - Service Update - Power Liftgate Actuator Failure. Inadequate laser welds on the power liftgate gear box may cause a noisy / non-functional actuator assembly resulting in the rear liftgate to not open / close, or stick in position. Visually inspect the liftgate actuator / gear box for suspect actuator lot number. If the lot number matches the lot number on the suspect list, replace the liftgate actuator / gear box.

030603004S

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

030603004T

Service Bulletin/Repair Instructions

Battery Testing and Warranty Replacement Requirements (North America ONLY)

040089015N

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on required operating procedures.

150601002E

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.

PIC6033A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have "Service Theft System" message on the Driver Information Center. Technician may find Diagnostic Trouble Code B291B sym 3B and is unable to clear the Diagnostic Trouble Code. Technician will need to restore communication between the Body Control Module and Theft Deterrent Sensor Module to clear the Diagnostic Trouble Code.

080730026D

Service Bulletin/Repair Instructions

This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

PIP5411C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have hesitation or a stalling condition while in ambient temperatures 100 degrees or higher. Technician may find Diagnostic Trouble Codes P2635 and or P018B set. The dealer is advised to replace the in tank fuel pump module assembly to correct the condition.

PIT5232C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps to diagnose and repair the concern of the display is showing 32° F (0° C) after a battery or reprogramming a module. The outside temperature will begin to update if driven above 20 mph for at least 5 minutes. If the vehicle speed drops below 20 mph, the timer will reset and the display will stop updating. Once the display starts to update it may take several more minutes of driving above 20 mph for the display to fully update. Also if the vehicle is shut off for more than 8 hours the display will update when the ignition is turned on.

050604022N

Service Bulletin/Repair Instructions

This informational bulletin provides information on the top tier fuels that are recommended in GM vehicles.

090089002N

Service Bulletin/Repair Instructions

This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.

100844006D

Service Bulletin/Repair Instructions

This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc information.

140089004C

Service Bulletin/Repair Instructions

The information in this bulletin details the proper configurations for the ignition key, fob, key tags and key rings and applying a QR code sticker or barcode sticker to a key fob.

PIC6186D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

00-03-10-003U

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

05-08-44-024E

Service Bulletin/Repair Instructions

This informational bulletin provides information on return or reimbursement of customer owned CDs, DVDs or Navigation Discs .

07-00-89-037J

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.

08-08-44-029G

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.

09-00-89-008C

Service Bulletin/Repair Instructions

This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

PIE0381

Service Bulletin/Repair Instructions

Thins engineering informational bulletin is requesting information from the field on vehicles that have the condition of rear auxiliary a/c not cooling or blowing warm air.

PIP5282A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ABOUT THE CALCULATION AND OPERATION OF THE ENGINE OIL LIFE MONITOR. THE MONITOR CALCULATES THE PERCENT OF OIL LIFE REMAINING, BASED ON 3 PATHWAYS. THE FIRST PATHWAY FOR OIL LIFE CALCULATION IS ENGINE REVOLUTIONS. THE SECOND PATHWAY FOR OIL LIFE CALCULATION IS THE MILEAGE FORM THE LAST REST FOR ALL GENERAL MOTORS POWERTRAINS EXCEPT THE VOLT. THE THIRD PATHWAY FOR OIL LIFE CALCULATION IS THE AMOUNT OF TIME THE OIL IS IN THE ENGINE. THE VOLT USES A 2 YEAR TIMER INSTEAD OF 1 YEAR. IT ALSO USES THE ENGINE REVOLUTION COUNTER. IT DOES NOT USE THE MILEAGE PATHWAY TO COUNT DOWN.

PIP5423

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A SERVICE ENGINE SOON MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES P0106 AND P0506. TECHNICIAN WILL INSPECT FOR A BROKEN VALVE SPRING AND REPLACE AS NEEDED.

09-00-89-016E

Service Bulletin/Repair Instructions

This warranty nonadministrative bulletin provides information on the proper use of the labor op 0600014.

11-00-89-005J

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Goodwill Tools, Customer Enthusiasm, and Policy Guidelines.

PIC6220

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES WITH AN INTERMITTENT LOSS OF GRIDLINES IN THE REAR CAMERA DISPLAY SCREEN AND A "SERVICE REAR VISION SYSTEM" MESSAGE THAT BOTH HAPPEN AT THE SAME TIME. TECHNICIAN SHOULD CHECK FOR DIAGNOSTIC TROUBLE CODES AND FOLLOW PUBLISHED SERVICE INFORMATION DIAGNOSTICS FOR THE DIAGNOSTIC TROUBLE CODES. IF NOT DIAGNOSTIC TROUBLE CODES STORED AND THE CONCERN WAS DUPLICATED OR THE CUSTOMER DESCRIBED THE CONCERN, DEALER SHOULD COMMUNICATE TO THE CUSTOMER THAT WE APOLOGIZE FOR THIS INCONVENIENCE AND THAT GENERAL MOTORS IS CURRENTLY EVALUATING THIS CONCERN.

PIP5427

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLE THAT MAY HAVE A SERVICE ENGINE SOON MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES P2635, U0074 AND OR U18A2. TECHNICIAN WILL NEED TO FOLLOW PUBLISHED DIAGNOSTICS FOR DIAGNOSTIC TROUBLE CODES U0074 WOULD TAKE PRIORITY OVER U18A2 IF BOTH SET BEFORE ADDRESSING DTC P2635.

PIC6086B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS TO RESOLVE THE ISSUE OF AN OILY SUBSTANCE THAT MAY BE FOUND ON THE INSIDE WINDSHIELD SURFACE, AND APPEARS TO BE LEAKING FROM THE REAR VIEW MIRROR AREA. TECHNICIAN WILL REMOVE THE MOISTURE SENSOR AND CLEAN THE GLASS AND MOUNTING BRACKET WITH ALCOHOL WIPE. IF THE GEL SEPARATES FROM THE SENSOR THE SENSOR WILL NEED TO BE REPLACED.

02-08-98-002G

Service Bulletin/Repair Instructions

This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done.

08-08-44-015G

Service Bulletin/Repair Instructions

This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs

PIT5206E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS ON DIAGNOSING AND REPAIRING VEHICLES THAT MAY HAVE UNWANTED GRADE BRAKING, REDUCED ENGINE POWER WITH NO DRIVER INFORMATION CENTER MESSAGES “ BRAKE PEDAL OVERRIDE FEATURE “, TRANSMISSION BUSY OR FREQUENT SHIFTING UP OR DOWN, AND DIAGNOSTIC TROUBLE CODES P057B, P057C, AND/OR P057D MAY OR MAY NOT BE SET. TECHNICIAN WILL USE THIS PRELIMINARY INFORMATION TO FIND THE BRAKE PEDAL POSITION DATA PARAMETERS IN THE SCAN TOOL, AND ALSO TO PROVIDE SOME ADDITIONAL DIAGNOSTIC HELP. THESE ISSUES MAY BE CAUSED BY AN INCORRECT BRAKE PEDAL POSITION SENSOR INPUT TO THE ENGINE CONTROL MODULE. TECHNICIAN WILL VERIFY WITH THE SCAN TOOL IF THE ENGINE CONTROL MODULE HAS THE CORRECT PARAMETERS FOR THE BRAKE PEDAL POSITION SENSOR. IF AN ENGINE CONTROL MODULE BRAKE PEDAL POSITION SENSOR RELEARN IS PERFORMED, THE TRUCK MAY BE TEMPORARILY REPAIRED UNTIL THE INTERMITTENT WIRING ISSUE BETWEEN THE ENGINE CONTROL MODULE AND BRAKE PEDAL POSITION SENSOR OCCURS AGAIN. ON 2014 AND NEWER TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X115 AND X119. ON THE 2014 AND PREVIOUS TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X205.

01-00-89-010L

Service Bulletin/Repair Instructions

This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).

PIP5422A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE SPEEDOMETER INACCURATE READS 5 MPH WHEN TRAVELING 50 MPH. ENGINEERING IS WORKING TO DEVELOP A SOLUTION.

07-08-49-020K

Service Bulletin/Repair Instructions

This informational bulletin explains the programming method quick reference guide for the IPC Odometer.

16-NA-306

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace the Homelink transmitter to correct the customers concern of the garage door wont open from far distances.

PIC6177A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH INFORMATION ON VEHICLES WITH NAVIGATION RADIO REGULAR PRODUCTION OPTION CODE IO6 OR UY4 THAT DEFAULTS TO WEST VIRGINIA INSTEAD OF VIRGINIA ON A MANUAL ENTRY. GENERAL MOTORS ENGINEERING IS CURRENTLY WORKING ON A SOLUTION FOR THIS CONCERN.

01-03-10-003L

Service Bulletin/Repair Instructions

This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage) and for vehicles within this warranty period, the defective tires will be replaced on a pro rata adjustment basis. It also provides GWM Transaction information.

PIT5384B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE THE ONSTAR WIRELESS FIDELITY INOPERATIVE. TECHNICIAN WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER WITH A SCAN TOOL CONNECT TO THE VEHICLE FOR FURTHER ASSISTANCE.

PIC6073C

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS DIAGNOSTIC TOOL KIT (EL-51578) HAS BEEN RELEASED TO HELP DIAGNOSE ANY OF THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS CONCERNS. THE KIT CONTAINS HEADER CONNECTORS THAT ARE INSTALLED TO BYPASS MEDIA ORIENTED SYSTEMS TRANSPORT BUS MODULES. THE BYPASS CONNECTOR ALSO CONTAINS A TERMINAL FOR VERIFYING MEDIA ORIENTED SYSTEMS TRANSPORT CONTROL CIRCUIT VOLTAGES. TECHNICIAN SHOULD REVIEW MEDIA ORIENTED SYSTEMS TRANSPORT BUS DESCRIPTION AND OPERATION AND DIAGNOSTIC TROUBLE CODE U0028 DIAGNOSTIC PROCEDURES.

PIE0370A

Service Bulletin/Repair Instructions

This engineering informational bulletin is ending the need of information from the field on vehicles with the condition of a rattle noise from the second row seat.

PIT5241D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT CUSTOMERS THAT MAY REQUEST THE FACTORY INTEGRATED TRAILER BRAKE CONTROLLER REGULAR PRODUCTION OPTION CODE (JL1) BE INSTALLED ON THEIR FULL-SIZE PICKUP OR SUV WHEN THE VEHICLE WAS NOT ORDERED WITH THE OPTION. DEALER SHOULD ADVISE THE CUSTOMER IT CANNOT BE ADDED TO THE VEHICLE.

PIE0362A

Service Bulletin/Repair Instructions

This engineering information bulletin annouces the end for the need for information from the field and to refer dealers to normal diagnostics.

PIP5382E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT GENERATION 5 ENGINES WITH REGULAR PRODUCTION OPTION CODE L83, L86, OR LV3 MAY HAVE AN OIL CONSUMPTION CONCERN WERE ONE QUART IN 2000 MILES IS BEING USED. DEALER WILL CONFIRM OIL LEVEL WAS PROPERLY CHECKED PER OWNER’S MANUAL, AND CHECK THE BOLT TORQUE ON THE VALVE LIFTER OIL MANIFOLD ASSEMBLY, BEFORE YOU CONTACTING GENERAL MOTORS PRODUCT QUALITY CENTER.

05-00-89-072D

Service Bulletin/Repair Instructions

This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information.

PIE0376

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information from the field on vehicles with the condition of a check engine light illuminated and a DTC of P0751, in addition the vehicles have less then 5,000 miles.

PIP5411B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE HESITATION OR A STALLING CONDITION WHILE IN AMBIENT TEMPERATURES 100 DEGREES OR HIGHER. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES P2635 AND OR P018B SET. THE DEALER IS ADVISED TO REPLACE THE IN TANK FUEL PUMP MODULE ASSEMBLY TO CORRECT THE CONDITION.

16NA241

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.

16NA043

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES THE CORRECT INFORMATION THAT IS NEEDED TO CORRECTLY KNOW WHAT TPM SENSOR IS NEEDED TO BE INSTALLED ON VEHICLES IF THERE IS ACCESSORY WHEELS INSTALLED AND WHO TO CONTACT WHEN THE ACCESSORY WHEELS WILL NOT LEARN THE TPM'S TO THE VEHICLES.

PIT5074J

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL

PIT5445A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN OF ADDITION INFORMATION WHEN DIAGNOSING A SERVICE DRIVER ASSIST MESSAGE WITH A DIAGNOSTIC TROUBLE CODE B172E AND OR A B172F. THE HAPTIC SEAT MOTOR HAS A PIGTAIL LEAD COMING OFF OF IT. IN MANY CASES THE WIRING PIGTAIL NEAR THE HAPTIC SEAT MOTOR HAS BROKEN AND WILL REQUIRE REPLACEMENT.

PIT5522

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT WHEN PROGRAMING THE IMMOBILIZER THEFT LEARN IT MAY NOT COMPLETE AND/OR SHOW "CONTROLLER ID NOT SUPPORTED" AFTER THE FIRST FEW MINUTES INTO THE LEARN EVENT. TECHNICIAN WILL NEED TO REMOVE POWER FROM THE ONSTAR MODULE BEFORE PERFORMING A IMMOBILIZER THEFT LEARN.

PI1394A

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.

PIT5411F

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HUMAN MACHINE INTERFACE, RADIO OR TUNER, RADIO CONTROLS, INTEGRATED CENTER STACK, DISPLAY, AND MEDIA DISC PLAYERS ARE PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. DEALER WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE.

PIP5411A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE HESITATION OR A STALLING CONDITION WHILE IN AMBIENT TEMPERATURES 100 DEGREES OR HIGHER. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES P2635 AND OR P018B SET. DEALER SHOULD COMMUNICATE TO THE CUSTOMER THAT WE APOLOGIZE FOR THIS INCONVENIENCE AND THAT GENERAL MOTORS IS WORKING ON A SOLUTION FOR THIS CONCERN. IF WORKING ON POLICE PURSUIT VEHICLES REGULAR PRODUCTION OPTION CODE PPV OR FLEET VEHICLES REGULAR PRODUCTION OPTION CODE FLT, CONTACT THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE.

PIT5307D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A SERVICE ENGINE SOON MALFUNCTION INDICATOR LAMP, ANTILOCK BRAKING SYSTEM MALFUNCTION INDICATOR LAMP, SERVICE SUSPENSION SYSTEM MESSAGE, MISFIRE, HESITATION, NO CRANK, HEATER-VENT-AIR CONDITIONING INOPERATIVE. TECHNICIAN MAY FIND F11UA, F104UA, F35UA, AND OR F60UA BLOWN. TECHNICIAN SHOULD INSPECT THE ENGINE HARNESS NEAR THE VACUUM PUMP PULLEY TO BE CHAFING. TECHNICIAN WILL NEED TO REROUTE THE WIRE HARNESS AND REPAIR AND DAMAGED WIRES.

PIT5308A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR VEHICLES THAT HAVE REMOTE START IS INOPERATIVE, POWER LIFT-GATE REGULAR PRODUCTION OPTION CODE (TB5) IS INOPERATIVE WITH THE IGNITION OFF, AND VEHICLES EQUIPPED WITH THE DIESEL ENGINE, THE BLOWER MOTOR MAY STAY ON AFTER THE ENGINE IS TURNED OFF. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODE P2537 SET. TECHNICIAN WILL NEED TO USE A VOLTMETER AND CHECK CIRCUIT 5985 AT THE ENGINE CONTROL MODULE AND TRANSMISSION CONTROL MODULE. IF NO OR LOW VOLTAGE IS FOUND, USE THE WIRING DIAGRAM IN SERVICE INFORMATION AND PERFORM NORMAL CIRCUIT DIAGNOSIS. TECHNICIAN WILL NEED TO INSPECT FOR HIGH RESISTANCE OR OPEN IN CIRCUIT 5985 IS UNDER THE DRIVER’S SILL PLATE AND REPAIR AS NEEDED.

PIT5391B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT HAVE A NO CRANK OR A START AND THEN IMMEDIATE STALL, SERVICE ENGINE SOON MALFUNCTION INDICATOR LAMP MAY NOT BE ON WHEN THE IGNITION IS IN THE RUN POSITION. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES P0513 AND OR P262B MAY ALSO BE SET. TECHNICIAN WILL PULLED THE DRIVER SILL PLATE AND INSPECT THE WIRING FOR DAMAGED OR CORRODED CIRCUITS. TECHNICIAN WILL REPAIR ANY DAMAGED OR CORRODED CIRCUITS.

PIT5405B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN FOR A REDUCED POWER MESSAGE, STEERING ASSIST, ENGINE STALL OR THE INSTRUMENT PANEL, RADIO, AND OR HEATER-VENT-AIR CONDITIONING GO BLANK WITH MULTIPLE DIAGNOSTIC TROUBLE CODES. IF ANY OF THE FOLLOWING DIAGNOSTIC TROUBLE CODES U0073, U0078, U0029, U0028, U0415, U0140, U0126, U0121, U0101, U0100, C0544, U1510, U0073, B127B, B2605, B3600,C0800, U0428, AND U0452 SET IN THE VEHICLE. CHECK THE BODY CONTROL MODULE GROUND AT THE G218 LOCATION. THE FRONT DASH INSULATOR MAT MAY BE TRAPPED BETWEEN THE GROUND EYELET AND THE BODY STUD. REMOVE THE ROUND NUT AND EYELET AND CUT THE FRONT DASH INSULATOR MAT AWAY FROM THE GROUND STUD SO IT NO LONGER INTERFERES WITH THE GROUND STUD AND REINSTALL THE EYELET AND GROUND NUT. TECHNICIAN SHOULD ALSO INSPECT CONNECTOR X183 AND X133FOR ANY BROKEN, LOOSE, BACKED OUT TERMINALS AND REPAIR AS NECESSARY.

PIT5403B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS TO DIAGNOSIS AND REPAIR VEHICLES WITH VARIOUS HANDLING, VEHICLE DYNAMICS CONCERNS, NOISES FROM THE SUSPENSION OR UNDERBODY, OR ISSUES RELATED TO DAMAGED SUSPENSION COMPONENTS. BEFORE ANY IN-DEPTH DIAGNOSTICS ARE PERFORMED, BE AWARE THAT VARIOUS ISSUES COULD OCCUR IF THE VEHICLE HAS BEEN MODIFIED AND INFORM THE CUSTOMER THE CONDITIONS NOTED MAY NOT BE COVERED UNDER WARRANTY. TECHNICIAN WILL INSPECT FOR INSTALLED AFTERMARKET SUSPENSION COMPONENTS. ALSO INSPECT FOR IMPROPERLY ADJUSTED TORSION BARS.

PI0388F

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.

PIP4786C

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.

PIP5337E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE A SHAKE OR SHUDDER DURING LIGHT THROTTLE ACCELERATION, BETWEEN 30 AND 65 MPH STEADY STATE DRIVING. ALSO SHUDDER FEELING THAT MAY BE DESCRIBED AS DRIVING OVER RUMBLE STRIPS OR ROUGH PAVEMENT. TECHNICIAN WILL DRIVE THE VEHICLE AND MONITOR THE TORQUE CONVERTER CLUTCH SLIP. THE TORQUE CONVERTER CLUTCH SLIP SPEED SHOULD BE 10 RPM OR LESS ALSO NOTE IF THE SHUDDER TAKES PLACE DURING TORQUE CONVERTER CLUTCH APPLY. IF THE TORQUE CONVERTER CLUTCH SLIP SPEED IS IN THE RANGE OF 10 RPM OR LESS THE CONDITION IS POSSIBLY RELATED TO ENGINE PERFORMANCE. IF THE SHUDDER IS ONLY PRESENT IN 4 CYLINDER MODE AND TORQUE CONVERTER CLUTCH SLIP IS 10 RPM OR LESS DEEM THE SHUDDER CONCERN NORMAL CHARACTERISTIC OF ACTIVE FUEL MANAGEMENT. IF THE SLIP SPEED IS BEYOND 10 RPM OR THERE IS SHUDDER DURING TORQUE CONVERTER CLUTCH APPLY THE TORQUE CONVERTER WILL NEED TO BE REPLACED.

030603004R

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.

140089004B

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION FOR IGNITION KEY, FOB, KEY TAGS AND KEY RINGS CONFIGURATION FOR VARIOUS VEHICLES AND APPLYING A QR CODE STICKER OR BARCODE STICKER TO THE FOB.

16NA249

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS LESS THAN 10,000 MILES ON IT.

PIP5205A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSING THE CONCERN OF A RATTLE, TICK AND/OR A VIBRATION FROM THE REAR OF THE VEHICLE. THIS COULD BE COMING FROM THE FUEL FEED LINE BETWEEN THE FUEL TANK AND ETHANOL SENSOR. TECHNICIAN WILL APPLY PRESSURE TO THE FUEL LINE TO DETERMINE IF THIS IS THE SOURCE OF THE CONCERN. IF IT IS DETERMINED THE FUEL LINE IS THE SOURCE OF THIS CONCERN REPLACE THE FUEL FEED PIPE BETWEEN THE CHASSIS LINE AND THE HIGH PRESSURE PUMP.

PIP5373A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS ON HOW TO PROGRAM AN ENGINE CONTROL MODULE WHEN GETTING A SERVICE PROGRAMMING SYSTEM ERROR CODE E4491 OR E4423. IN SOME CASES TECHLINE CUSTOMER SUPPORT CENTER MAY NEED TO BE CONTACTED TO RESOLVE THE ISSUE.

PIP5382C

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT GENERATION 5 ENGINES WITH REGULAR PRODUCTION OPTION CODE L83, L86, OR LV3 MAY HAVE AN OIL CONSUMPTION CONCERN WERE ONE QUART IN 2000 MILES IS BEING USED. DEALER WILL CONFIRM OIL LEVEL WAS PROPERLY CHECKED PER OWNER’S MANUAL, AND CHECK THE BOLT TORQUE ON THE VALVE LIFTER OIL MANIFOLD ASSEMBLY, BEFORE YOU CONTACTING GENERAL MOTORS PRODUCT QUALITY CENTER.

070898001B

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF “CLIPPING” TO REPAIR COLLISION DAMAGE TO VEHICLES. GM HAS NOT TESTED OR VALIDATED A “CLIPPED VEHICLE” REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.

16NA246

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON LOCATING AND RECONNECTING AIRBAG CONNECTORS THAT ARE NOT FULLY SEATED TO CORRECT A CUSTOMER CONCERN OF AN AIRBAG WARNING LAMP ILLUMINATED, OR ONE, OR MORE, AIRBAG DTC(S) SET.

000601012F

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.

030604017I

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.

110849001S

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.

16NA242

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES DIAGNOSTIC TIPS TO HELP CORRECT MULTIPLE CONCERNS REGARDING THE USB PORT BEING INOPERATIVE OR UNABLE TO PLAY MUSIC THROUGH THE USB PORT.

000601026I

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE.

00-06-01-026H

Service Bulletin/Repair Instructions

This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.

15-06-01-002D

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE VALVE LIFTER OIL MANIFOLD AND THE LIFTERS TO CORRECT THE CUSTOMERS CONCERN OF ENGINE MISFIRE, TICK NOISE AND MIL ON.

16-NA-223

Service Bulletin/Repair Instructions

This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Or, they may come in for ABS or general handling/braking concerns.

PIE0370

Service Bulletin/Repair Instructions

THIS ENGINEERING INFORMATIONAL BULLETIN IS REQUESTING INFORMATION FROM THE FIELD WITH THE CONDITONS OF A RATTLE NOISE ORIGINATING FROM THE SECOND ROW SEAT.

16-NA-219

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE HMI MODULE TO CORRECT A CONDITION OF GPS INOPERATIVE, RED LINE ACROSS GPS INDICATOR OR THE LOCATION IS STUCK IN WARREN MICHIGAN.

PIE0360A

Service Bulletin/Repair Instructions

THIS ENGINEERING INFORMATIONAL BULLETIN IS ENDING THE NEED FOR INFORMATION FROM THE FIELD OF VEHICLES WITH THE CONDITION OF INTERMITTENT HVAC COOLING ISSUES WHILE DRIVING.

00-03-10-006M

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES GUIDANCE TO GM DEALERS WHEN USING GM APPROVED TIRE FORCE VARIATION MEASUREMENT EQUIPMENT.

PIC6210

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATES THE PROCEDURE TO THE TECHNICIAN HOW TO REGAIN BLU-RAY/CD/DVD PLAYER FUNCTION ON ALL NEW GENERATION INFOTAINMENT SYSTEMS WITH REGULAR PRODUCTION OPTION CODE U42 OR UWG BLU-RAY PLAYERS. IF THIS CONCERN IS ENCOUNTERED, CYCLE THE CD PLAYER/MEDIA DISC PLAYER FUSE AND RE-EVALUATE THE CONCERN.

PIT5361B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE ISSUES WERE THE CUSTOMER WILL NEED INCREASED EFFORT TO DEPRESS THE BRAKE PEDAL. TECHNICIAN MAY FIND FLUID IN THE BRAKE BOOSTER AND/OR THE BOOSTER VACUUM LINE. TECHNICIAN WILL NEED TO REPLACE VACUUM PUMP, BRAKE BOOSTER, MASTER CYLINDER, VACUUM PUMP BELT AND THE VACUUM LINE BETWEEN THE BOOSTER AND THE PUMP.

PIT5511

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A DIM DRIVER INFORMATION CENTER WHEN THE INTERIOR OF THE VEHICLE IS HOT FROM A SUN LOAD OR EXTENDED HEATER OPERATION. THE DRIVER INFORMATION CENTER IS DESIGNED TO DIM WITH HIGH TEMPERATURE EXPOSURE. THIS IS DONE TO PROTECT THE DRIVER INFORMATION CENTER FROM DAMAGE.

PIT5284B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE A RATTLE NOISE FROM THE SECOND ROW SEAT. TECHNICIAN WILL NEED TO INSPECT THE STRIKER NOT ALIGNED PROPERLY IN LATCH OPENING. TO REPAIR THIS CONDITION, REWORK/ADJUST THE STRIKER IN THE DIRECTION TO CENTER IT IN THE LATCH OPENING. AN ADJUSTABLE WIDE MOUTH METAL WORKING TOOL MAY BE USED TO ADJUST THE STRIKER JUST ENOUGH TO CENTER IN THE LATCH OPENING. TECHNICIAN MAY FIND A SEAT BOTTOM LATCH MAY HAVE AN UNEQUAL LATCH OPENING SIDE-TO-SIDE FOR THE STRIKER TO SEAT INTO. TO REPAIR THIS CONDITION, WITH THE AFFECTED SEAT IN THE TUMBLED FORWARD POSITION, WHILE APPLYING STEADY, FIRM PRESSURE, CYCLE THE SEAT DOWN INTO THE LATCHED POSITION. SOME VEHICLES BUILT PRIOR TO 09/21/2015 WITH 60/40 SPLIT BENCH SEAT MAY HAVE 60-PERCENT LONG SIDE BENCH, INBOARD LATCH MAY NOT BE PROPERLY ALIGNED IN STRIKER OPENING. TECHNICIAN WILL NEED TO PLACE A 2.6 MM THICK FLAT WASHER OVER THE 40 PERCENT SEAT BASE STUD, NOT THE FLOOR STUD. SOME VEHICLES MAY HAVE A SEAT BASE PLAT THAT RATTLES AGAINST THE RIB IN THE FLOOR PAN. APPLY MYLAR TAPE TO THE FLOOR PAN UNDER THE SEAT PLATE TO PROVIDE RELIEF FOR THE RATTLE CONDITION.

11-08-49-001R

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.

16-NA-171

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES INFORMATION ON THE PROPER RECONNECTION OF THE REAR WINDOW DEFROSTER TAB IF A CUSTOMER COMMENTS ONE LOOSE OR BROKEN.

PIP5094A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.

PIP5395A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE RATTLE OR TICKING NOISE THAT IS LOUDER INSIDE THE VEHICLE THAN OUTSIDE. THE NOISE MAY ALSO SOUND LIKE A LIFTER TICK. IF THE NOISE IS HEARD BEST AT THE FUEL LINE AND THE SOUND WILL BE REAL LOUD WITH A STETHOSCOPE. THE FUEL LINE WILL NEED TO BE REPLACED.

PIT5509

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLE THAT MAY HAVE A "CHECK TRAILER WIRING" OR "SERVICE TRAILER BRAKE SYSTEM” MESSAGE ON THE DRIVER INFORMATION CENTER WHEN A TRAILER IS CONNECTED TO THE VEHICLE. DIAGNOSTIC TROUBLE CODE C1114 SET IN THE CHASSIS CONTROL MODULE. CHASSIS CONTROL MODULE HAS TO DETERMINE THE TYPE OF TRAILER BRAKE SYSTEM THAT IS BEING USED. THE CHASSIS CONTROL MODULE CAN BE SENSITIVE TO A VARIETY OF TRAILER WIRING ISSUES. THE TECHNICIAN WILL NEED TO MAKE A TRAILER TESTER USING ELECTRIC TRAILER BRAKE MAGNETS AND 7-WAY TRAILER CONNECTOR TO DETERMINE IF IT IS A VEHICLE OR TRAILER ISSUE. IF THE CONCERN IS NOT DUPLICATED WITH THE TESTER INSTALLED, THE VEHICLE IS OPERATING CORRECTLY AND THE FOCUS SHOULD BE ON THE TRAILER WIRING OR 7 WAY CONNECTOR.

PIE0350C

Service Bulletin/Repair Instructions

THIS ENGINEERING INFORMATIONAL BULLETIN IS ENDING THE NEED FOR INFORMATION FROM THE FIELD OF VEHICLES WITH THE CONDITION OF BANG OR LOUD NOISE WITH NO FORWARD (DRIVE) OR REVERSE RANGES.

PIP5407

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE DIAGNOSTIC TROUBLE CODE P06DD OR NO OR LOW OIL PRESSURE. TECHNICIAN WILL REPLACE TIMING CHAIN TENSIONER GUIDE. IF OIL PUMP FACE IS DAMAGED AND OR WORN THRU REPLACE OIL PUMP. INSPECT BEARINGS FOR DAMAGE WEAR DUE TO DEBRIS FROM OIL PUMP.

10-08-110-001E

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PROPER USE OF FLOOR MATS.

PIP5211E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR VEHICLES WITH A ROUGH IDLE AND/OR VIBRATION AT IDLE IN DRIVE. THIS CONDITION WILL NOT BE PRESENT IN PARK, OR NEUTRAL. THIS CONCERN MAY BE CAUSED BY GROUND OUT WITHIN THE ONE OR BOTH ENGINE MOUNTS. TECHNICIAN WILL USE CH-51450-A (PICO OSCILLOSCOPE) TO MEASURE THE VIBRATION DISTURBANCE. IF THE VIBRATION CONCERN IS E1.5 IN THE HORIZONTAL / LATERAL DIRECTION WITH PICO SENSOR MOUNTED IN SEAT TRACK AS INDICATED – CONTINUE WITH STEPS TO REDUCE THE AMPLITUDE OF THE VIBRATION BY ADDING SPACERS IN KEY LOCATIONS TO REDUCE GROUND OUT WITHIN THE ENGINE MOUNTS. THE 6.2L ENGINE HAS A CHARACTERISTIC E1 WHICH CAN BE FELT, AND MAY BE DESCRIBED AS A LOPEY IDLE. DO NOT CONFUSE 6.2L E1 CHARACTERISTIC (NOT CAUSED BY MOUNT GROUND-OUT), WITH E1.5 NORMAL IDLE CHARACTERISTICS BEING TRANSMITTED INTO THE TRUCK VIA GROUND-OUT THRU THE ENGINE MOUNTS. IF MEASURING HIGH AT THE SEAT TRACK 12 MG OR GREATER; REPLACEMENT OF THE ENGINE MOUNTS SHOULD HELP REDUCE THE AMPLITUDE OF THE VIBRATION. IF THE DISTURBANCE MEASURES AT THE SEAT TRACK AS E1.5 LATERAL IN THE RANGE OF APPROXIMATELY 2.5 - 8 MG USING A TRI-AXIS SENSOR. THEN PLACE TRI-AXIS PICO SENSOR ON THE INBOARD SEAT TRACK FORWARD-MOST LOCATION TO RECORD MEASUREMENT OF THE ROUGH IDLE VIBRATION CONCERN. WITH THE HEATER-VENT-AIR CONDITIONING ON PERFORM SEVERAL SHORT HEAVY LAUNCH EVENTS FROM STOP TO STOP TO BRING THE TEMPERATURES BACK UP WHILE ATTEMPTING TO RE-CREATE THE ROUGH IDLE VIBRATION IN DRIVE WITH PICO SENSOR PLACED ON INBOARD SEAT TRACK; WHILE THE VIBRATION IS ACTIVE – RECORD PICO READING. THIS METHOD SEEMS TO PROVIDE BETTER RESULTS THAN EXTENDED TEST DRIVES. IF THE PICO READING FOR E1.5, WITH VIBRATION ACTIVE, AT SPECIFIED SEAT TRACK LOCATION MEASURES CLOSE TO 2MG OR LESS USE SERVICE INFORMATION TO DIAGNOSE ROUGH IDLE / VIBRATION.

PIT5311B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE AN INTERMITTENT "CHECK TRAILER WIRING" OR "SERVICE TRAILER BRAKE" MESSAGE ON THE DRIVER INFORMATION CENTER. TECHNICIAN WILL INSPECT AND CLEAN THE GROUND WIRE (NORMALLY WHITE WIRE) CONNECTION ON THE TRAILER SIDE OF THE 7-PIN CONNECTOR. INSPECT THAT THE WIRES INSIDE THE TRAILER SIDE CONNECTOR ARE CLEAN AND SECURELY FASTENED. IF THE VEHICLE’S 7-WAY CONNECTOR SOCKET TERMINALS ARE DEFORMED OR HAVE EXCESSIVE WEAR, IT WILL BE NECESSARY TO REPLACE THE TRUCK SIDE CONNECTOR FROM GENERAL MOTORS CUSTOMER CARE AND AFTERSALES ALONG WITH THE TRAILER'S 7-WAY CONNECTOR PLUG.

PIP5337D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEP TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE A SHAKE OR SHUDDER DURING LIGHT THROTTLE ACCELERATION, BETWEEN 30 AND 65 MPH STEADY STATE DRIVING. ALSO SHUDDER FEELING THAT MAY BE DESCRIBED AS DRIVING OVER RUMBLE STRIPS OR ROUGH PAVEMENT. TECHNICIAN WILL DRIVE THE VEHICLE AND MONITOR THE TORQUE CONVERTER CLUTCH SLIP. THE TORQUE CONVERTER CLUTCH SLIP SPEED SHOULD BE 10 RPM OR LESS ALSO NOTE IF THE SHUDDER TAKES PLACE DURING TORQUE CONVERTER CLUTCH APPLY. IF THE TORQUE CONVERTER CLUTCH SLIP SPEED IS IN THE RANGE OF 10 RPM OR LESS THE CONDITION IS POSSIBLY RELATED TO ENGINE PERFORMANCE. IF THE SHUDDER IS ONLY PRESENT IN 4 CYLINDER MODE AND TORQUE CONVERTER CLUTCH SLIP IS 10 RPM OR LESS DEEM THE SHUDDER CONCERN NORMAL CHARACTERISTIC OF ACTIVE FUEL MANAGEMENT. IF THE SLIP SPEED IS BEYOND 10 RPM OR THERE IS SHUDDER DURING TORQUE CONVERTER CLUTCH APPLY THE TORQUE CONVERTER WILL NEED TO BE REPLACED.

09-06-04-026M

Service Bulletin/Repair Instructions

This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2.

99-08-51-007G

Service Bulletin/Repair Instructions

This informational bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening or re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed.

PIC-6095-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH A DIAGNOSTIC AID FOR IDENTIFYING INFOTAINMENT COMPONENTS ON THE VEHICLES TO ENSURE THAT THE CORRECT COMPONENT IS ORDERED OR REPLACED AND THE CORRECT LABOR CODE IS USED FOR WARRANTY SUBMISSION.

PI0592D

Service Bulletin/Repair Instructions

This informational bulletin provides information on service programming system (SPS) errors.

PIT-5508

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES WITH ONE OF THE TWO CONCERNS. VEHICLE MAY HAVE AN INTERMITTENT "SERVICE POWER STEERING, DRIVE WITH CARE" ON THE DRIVER INFORMATION CENTER AND A DIAGNOSTIC TROUBLE CODE C0545 SYMPTOM 00 SET IN THE POWER STEERING CONTROL MODULE. OR THE VEHICLE MAY HAVE INOPERATIVE AIR CONDITION CAUSED BY ANY OF THE FOLLOWING DIAGNOSTIC TROUBLE CODE B393B, FUSE F60UA OR F35UA BEING OPEN, OR A POOR AIR CONDITION COMPRESSOR CLUTCH GROUND. TECHNICIAN WILL GAIN ACCESS TO THE WIRE HARNESS UNDER THE AIR CONDITION COMPRESSOR, INSPECT FOR DAMAGE WIRES AND REPAIR THE WIRES.

PIE0365

Service Bulletin/Repair Instructions

This engineering information bulletin is requesting information from the dealers on a customer concern that one of the USB ports is not charging, allowing data to transfer.

10-00-89-005F

Service Bulletin/Repair Instructions

This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information.

PIT-5301-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT DIAGNOSTIC TROUBLE CODE B127E IN THE HUMAN MACHINE INTERFACE WITH REGULAR PRODUCTION OPTION CODE U42 OR UWG WILL BE CURRENT WHEN PLAYING A DVD OR BLU-RAY ON THE INTEGRATED CENTER STACK DISPLAY. WHEN THE DISC IS EJECTED THE DIAGNOSTIC TROUBLE CODE WILL BE HISTORY. IF THE DIAGNOSTIC TROUBLE CODE B127E REMAINS CURRENT AFTER EJECTING THE DISC FOLLOW SERVICE INFORMATION DIAGNOSTIC PROCEDURE INSTRUCTIONS FOR B127E WITH REGULAR PRODUCTION OPTION CODE U42 OR UWG.

12-08-132-001D

Service Bulletin/Repair Instructions

This informational bulletin provides warranty information on accessory power outlet and trailer lighting fuse replacement.

PIC-6201

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH THE STEPS NEEDED TO DIAGNOSE AND REPAIR A VEHICLE WITH WI-FI OR BLUETOOTH INOPERATIVE OR POOR PERFORMANCE CONCERN. TECHNICIAN WILL NEED TO OBTAIN DATA FROM GLOBAL DIAGNOSTICS SERVICES 2 AND CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE.

16-NA-152

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to reprogram the BCM to correct a customer concern on a dead battery or no start and DTC B1527 set caused by to the child window lock, when active, causing the BCM to continuously wake up and run the battery down.

PIT-5507

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT VEHICLES EQUIPPED WITH ULTRASONIC PARK ASSIST SYSTEM REGULAR PRODUCTION OPTION CODE UD5 OR UD7 WITH A DIAGNOSTIC TROUBLE CODE U0159 SET IN THE INSTRUMENT PANEL CLUSTER AND /OR THE BODY CONTROL MODULE ENGINEERING IS CURRENTLY WORKING ON AN UPDATED CALIBRATION TO CORRECT THE CONCERN.

11-08-49-001Q

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE IDENTIFICATION OF VEHICLES THAT ARE SHIPPED WITH THE TRANSPORT MODE ON AND HOW TO TURN IT OFF.

PIC-6086-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS TO RESOLVE THE ISSUE OF AN OILY SUBSTANCE THAT MAY BE FOUND ON THE INSIDE WINDSHIELD SURFACE, AND APPEARS TO BE LEAKING FROM THE REAR VIEW MIRROR AREA. TECHNICIAN WILL REMOVE THE MOISTURE SENSOR AND CLEAN THE GLASS AND MOUNTING BRACKET WITH ALCOHOL WIPE. IF THE GEL SEPARATES FROM THE SENSOR THE SENSOR WILL NEED TO BE REPLACED.

SB-02-07-30-029Z

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE PRODUCT QUALITY CENTER (PQC) ASSEMBLY REPLACEMENT PROCESS.

SB-15-06-01-002C

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE VALVE LIFTER OIL MANIFOLD AND AFFECTED BANK OF AFM LIFTERS TO CORRECT A CUSTOMER CONCERN ON A MALFUNCTION INDICATOR LAMP (MIL) ON AND/OR AN ENGINE MISFIRE/TICK NOISE WITH DTC P0300 SET DUE TO AN ACTIVE FUEL MANAGEMENT (AFM) LIFTER THAT IS MECHANICALLY COLLAPSED AND/OR STUCK ALL OF THE TIME.

SB-16-NA-130

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO INSPECT THE UPPER VALVE BODY TO DETERMINE THE CORRECT RPO USAGE TO CORRECT A CONCERN THAT AFTER INSTALLATION OF A REPLACEMENT UPPER VALVE BODY, THE TRANSMISSION MAY HAVE NO REVERSE AND NO 2ND GEAR DUE TO THE INSTALLATION OF THE INCORRECT UPPER VALVE BODY.

SB-16-NA-138

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO ADVISE THE CUSTOMERS THAT HAVE ENROLLED THEIR VEHICLE INTO THE ONSTAR ADVANCED DIAGNOSTICS & REAL TIME DIAGNOSTIC ALERTS THEY MAY RECEIVE ALERTS FROM THEIR VEHICLE WHEN IT IS BEING SERVICED.

SB-16NA-131

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON VEHICLES DESIGNED TO OPERATE ON GASEOUS FUELS.

SB-16-NA-137

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSTALL A NEW FOAM PATCH OVER THE MICROPHONE TO CORRECT A CUSTOMER CONCERN THAT WHEN USING THE BLUETOOTH® PHONE SYSTEM IN THEIR VEHICLE, THE PERSON ON THE RECEIVING END OF A MOBILE TELEPHONE CALL STATES THE AUDIO SOUNDS MUFFLED, DISTORTED OR HAS STATIC DUE TO THE FOAM PATCH ON THE BACK OF THE HEADLINER AT THE MICROPHONE MOUNTING AREA COMING LOOSE.

PIP-5395

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF A RATTLE OR TICKING NOISE THAT IS LOUDER INSIDE THE VEHICLE THAN OUTSIDE. INSTRUCTIONS ARE PROVIDED TO INSPECT THE FUEL FEED LINE BETWEEN THE HIGH PRESSURE FUEL PUMP AND CHASSIS FUEL LINE.

PIP5395

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF A RATTLE OR TICKING NOISE THAT IS LOUDER INSIDE THE VEHICLE THAN OUTSIDE. INSTRUCTIONS ARE PROVIDED TO INSPECT THE FUEL FEED LINE BETWEEN THE HIGH PRESSURE FUEL PUMP AND CHASSIS FUEL LINE.

SB-16-NA-134

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO UPDATE THE IPC FIRMWARE TO CORRECT A CONCERN THAT A TECHNICIAN MAY HAVE AN ISSUE PERFORMING THE USB FILE TRANSFER PORTION OF THE IPC PROGRAMMING PROCESS IF THE ANDROID AUTO UPGRADE (BULLETIN 16-NA-042) HAS BEEN DONE PREVIOUSLY.

PIC-5374-D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.

PIC5374D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.

PIP-5189-B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF BLACK SMOKE WHEN STARTING THE VEHICLE AFTER SITTING.

PIP-5308-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF THE SERVICE ENGINE SOON LIGHT IS ON, AND THE ENGINE HAS LOW OIL PRESSURE.

PIP5189B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF BLACK SMOKE WHEN STARTING THE VEHICLE AFTER SITTING.

PIP5308A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF THE SERVICE ENGINE SOON LIGHT IS ON, AND THE ENGINE HAS LOW OIL PRESSURE.

PIT-5401-F

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF THE RADIO IS INOPERTIVE. NEW SOFTWARE HAS BEEN RELEASED TO CORRECT THIS CONCERN.

PIT5401F

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF THE RADIO IS INOPERTIVE. NEW SOFTWARE HAS BEEN RELEASED TO CORRECT THIS CONCERN.

PIE-0362

Service Bulletin/Repair Instructions

THIS ENGINEERING INFORMATION BULLETIN IS REQUESTING INFORMATION FROM THE DEALERS ON A CUSTOMER CONCERN THAT A SERVICE 4WD MESSAGE DISPLAYED ON THE DIC AND DTC C0398 SET WITHIN THE TRANSFER CASE CONTROL MODULE.

PIE-1250-E

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE INTRODUCTION OF THE ADVANCED DIAGNOSTICS - PROACTIVE ALERTS AVAILABLE ON MANY MODELS.

PIC6183A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF THE RADIO SYSTEM INOPERATIVE. THE TECHNICIAN IS TO CALL THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER WITH THE FINDINGS FROM THE QUESTIONS PROVIDED.

PIC6193A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER FOR FURTHER INSTRUCTIONS. THE CONCERN IS THE RADIO MAY BE UNABLE TO SAVE XM FAVORITE STATIONS.

PIC6197

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. PHONE WILL NOT CONNECT TO ANDROID AUTO.

PIP5168E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN, AND THE STEPS TO REPAIR THE CONCERN OF THE VEHICLE CRANKS BUT DOES NOT START. THE TECHNICIAN IS TO INSPECT FOR A SHEARED CAM PIN IN THE ENGINE.

SB-16-NA-042

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN ANNOUNCES THAT GM IS OFFERING AN ANDROID AUTO FEATURE UPGRADE FOR 2016 MODEL YEAR VEHICLES.

PIC4707E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.

PIC5088F

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.

SB-10-08-46-001C

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CONTACT ONSTAR FOR HARD MUTE REQUEST TO CORRECT A CUSTOMER CONCERN WHEN THE RADIO IS ON, IT DOES NOT MUTE ENOUGH WHEN THE ONSTAR® TURN-BY-TURN NAVIGATION DIRECTIONS ARE ANNOUNCED DUE TO CUSTOMER IMPROPERLY SETTING THE RADIO VOLUME HIGH ENOUGH WHEN THE TURN-BY-TURN NAVIGATION MESSAGES ARE PLAYED.

SB-15-06-03-001B

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE USEFUL ON DIAGNOSING BATTERIES THAT HAVE SET FOR A LONG PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES.

PIC-4935-E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

PIC4935E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

PIT5389A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.

PIC-6186-B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO CONTACT GM TECHNICAL ASSISTANCE CENTER TO REPORT THE CONCERN AND OBTAIN A CASE NUMBER WHEN A CUSTOMER MAY COMMENT THAT THEY WILL HAVE THE RADIO SHUT OFF, AND WHEN RESTARTING THE VEHICLE THE RADIO WILL TURN ON UNWANTED.

PIC6186B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO CONTACT GM TECHNICAL ASSISTANCE CENTER TO REPORT THE CONCERN AND OBTAIN A CASE NUMBER WHEN A CUSTOMER MAY COMMENT THAT THEY WILL HAVE THE RADIO SHUT OFF, AND WHEN RESTARTING THE VEHICLE THE RADIO WILL TURN ON UNWANTED.

SB-03-06-03-004Q

Service Bulletin/Repair Instructions

THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY.

SB-06-08-47-001L

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES WARRANTY INFORMATION ON USING THE SERVICE PROGRAMMING SYSTEM (SPS) FOR PROGRAMMING CONTROL MODULES

SB-07-06-01-016C

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION INTERNAL ENGINE NOISE OR DAMAGE AFTER OIL FILTER REPLACEMENT

SB-16-NA-119

Service Bulletin/Repair Instructions

THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON GM’S POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA.

PIT-5457-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN, AND COMPLETING A WIRING REPAIR. THE VEHICLE MAY HAVE A SERVICE ANTILOCK BRAKING SYSTEM, TRACTION CONTROL, POWER STEERING OR SUSPENSION SYSTEM MESSAGE ON THE DRIVERS INFORMATION CENTER.

PIT5457A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN, AND COMPLETING A WIRING REPAIR. THE VEHICLE MAY HAVE A SERVICE ANTILOCK BRAKING SYSTEM, TRACTION CONTROL, POWER STEERING OR SUSPENSION SYSTEM MESSAGE ON THE DRIVERS INFORMATION CENTER.

PIC6193

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN NOT TO MAKE ANY REPAIRS OR REPLACE ANY PARTS. THE TECHNICIAN IS TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER TO REVIEW A CONCERN WHEN THE VEHICLE'S RADIO IS UNABLE TO SAVE A XM PRESET AFTER SAVING PRESETS.

PI-0754-B

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT.

SB-16-NA-117

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PURPOSE OF MAGNETIC DRAIN PLUGS.

PIT-5287-B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS REQUIRED FOR THE FRONT SHOCK ABSORBER TERMINAL REMOVAL.

PIT-5504

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS ON HOW TO PROGRAM THE INSTRUMENT PANEL CLUSTER AFTER AN ANDROID AUTO UPDATE. DEALER WILL NEED TO CONTACT GM TECHNICAL ASSISTANCE CENTER TECHLINE CUSTOMER SUPPORT AT 1-800-828-6860 FOR ADDITIONAL INSTRUMENT PANEL CLUSTER USB PROGRAMMING ASSISTANCE.

PIT5287B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS REQUIRED FOR THE FRONT SHOCK ABSORBER TERMINAL REMOVAL.

PIT5504

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS ON HOW TO PROGRAM THE INSTRUMENT PANEL CLUSTER AFTER AN ANDROID AUTO UPDATE. DEALER WILL NEED TO CONTACT GM TECHNICAL ASSISTANCE CENTER TECHLINE CUSTOMER SUPPORT AT 1-800-828-6860 FOR ADDITIONAL INSTRUMENT PANEL CLUSTER USB PROGRAMMING ASSISTANCE.

PI-0281-E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS.

PIP-5382-B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION HAS THE STEPS FOR DIAGNOSING THE CONCERN OF EXCESSIVE OIL CONSUMPTION FOR THE GENERATION 5 ENGINE. DIAGNOSTIC INFORMATION IS PROVIDED FOR THE TECHNICIAN TO GATHER PRIOR TO CONTACTING THE PRODUCT QUALITY CENTER FOR FURTHER ASSISTANCE.

PIP5382B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION HAS THE STEPS FOR DIAGNOSING THE CONCERN OF EXCESSIVE OIL CONSUMPTION FOR THE GENERATION 5 ENGINE. DIAGNOSTIC INFORMATION IS PROVIDED FOR THE TECHNICIAN TO GATHER PRIOR TO CONTACTING THE PRODUCT QUALITY CENTER FOR FURTHER ASSISTANCE.

PIT-5380-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO REPAIR THE CONCERN OF THE VEHICLE'S FRONT SEAT APPEARS TO BE TOO FAR FORWARD. THIS CONCERN COULD BE CAUSED BY THE SEAT BOTTOM TRIM COVER NOT INSTALLED CORRECTLY ONTO THE CUSHION/FOAM. INSTRUCTIONS ARE PROVIDED TO CORRECTLY INSTALL THE SEAT BOTTOM TRIM COVER.

PIC-5260-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.

PIC5260A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.

PIT-5288-D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN. CUSTOMER'S POSSIBLE CONCERNS ARE: REMOTE KEYLESS ENTRY INOPERATIVE, PASSIVE ENTRY AND START INOPERATIVE, NO FOB DETECT MESSAGE ON DRIVERS INFORMATION CENTER, SERVICE TIRE PRESSURE SYSTEM, NO AUDIO, TOUCH SCREEN INOPERATIVE, OR RADIO AND/OR DRIVERS INFORMATION CENTER DISPLAY BLANK INOPERATIVE.

PIT-5307-C

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN WHEN THE VEHICLE HA SA SERVICE ENGINE SOON LIGHT, ANTILOCK BRAKING SYSTEM LIGHT OR SERVICE SUSPENSION MESSAGE, MISFIRE, HESITATION, NO CRANK, AIR CONDITIONING INOPERATIVE.

PIT5288D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN. CUSTOMER'S POSSIBLE CONCERNS ARE: REMOTE KEYLESS ENTRY INOPERATIVE, PASSIVE ENTRY AND START INOPERATIVE, NO FOB DETECT MESSAGE ON DRIVERS INFORMATION CENTER, SERVICE TIRE PRESSURE SYSTEM, NO AUDIO, TOUCH SCREEN INOPERATIVE, OR RADIO AND/OR DRIVERS INFORMATION CENTER DISPLAY BLANK INOPERATIVE.

PIT5307C

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN WHEN THE VEHICLE HA SA SERVICE ENGINE SOON LIGHT, ANTILOCK BRAKING SYSTEM LIGHT OR SERVICE SUSPENSION MESSAGE, MISFIRE, HESITATION, NO CRANK, AIR CONDITIONING INOPERATIVE.

PIC-6186-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION IS TO CONTACT GM TECHNICAL ASSISTANCE CENTER TO REPORT THE CONCERN AND OBTAIN A CASE NUMBER. CUSTOMERS MAY COMMENT THAT THEY WILL HAVE THE RADIO SHUT OFF, AND WHEN RESTARTING THE VEHICLE THE RADIO WILL TURN ON UNWANTED.

PIC-6187-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION IS TO CONTACT GM TECHNICAL ASSISTANCE CENTER TO REPORT THE CONCERN AND OBTAIN A CASE NUMBER. THE CUSTOMER IS UNABLE TO SELECT RADIO PRESETS FROM THE USB OR SD CARD AS THEY ARE GREYED OUT.

PIC6186A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION IS TO CONTACT GM TECHNICAL ASSISTANCE CENTER TO REPORT THE CONCERN AND OBTAIN A CASE NUMBER. CUSTOMERS MAY COMMENT THAT THEY WILL HAVE THE RADIO SHUT OFF, AND WHEN RESTARTING THE VEHICLE THE RADIO WILL TURN ON UNWANTED.

PIC6187A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION IS TO CONTACT GM TECHNICAL ASSISTANCE CENTER TO REPORT THE CONCERN AND OBTAIN A CASE NUMBER. THE CUSTOMER IS UNABLE TO SELECT RADIO PRESETS FROM THE USB OR SD CARD AS THEY ARE GREYED OUT.

SB-03-07-29-004K

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE OPERATING CHARACTERISTICS OF A MANUAL TRANSMISSION.

SB-06-06-05-001G

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON CHANGES IN EXHAUST TONE FOR ACTIVE FUEL MANAGEMENT ENGINES WHEN IN THREE OR FOUR CYLINDER MODE.

SB-16-NA-107

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE RADIO TO CORRECT A CUSTOMER CONCERN OF RADIO INOPERATIVE, BLUE SCREEN, AM CLIPPING NOISE, HD ON/OFF STATUS NOT RETAINED IN STATIONS, TIME LAG ON TRANSITIONS, NO AUDIO WITH INTERNAL AMP, PARK ASSIST SYMBOL POSITION WRONG IN REAR VIEW CAMERA.

SB-16-NA-109

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT THE STEERING GEAR FOR A NORMAL CONDITION OF GREASE OR SEALANT ON EXTERIOR CASE OF GEAR DUE TO THE MANUFACTURING PROCESS.

PIT5236G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.

00-03-10-002J

Service Bulletin/Repair Instructions

This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes.

PI0572C

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information on GM is implementing a new service strategy that uses a set of universal coaxial repair kits to service vehicles. This only applies to cable used for high frequency signals, such as cellular (OnStar®), satellite radio (XM) and GPS (navigation). The kits do NOT apply to the AM/FM cables.

PI0360F

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information on GM Accessory Remote start not working with onstars remotelink phone applications

PIT5438B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.

09-06-04-026L

Service Bulletin/Repair Instructions

This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2® or GDS 2 (U.S. and Canada)

PI1250D

Service Bulletin/Repair Instructions

This preliminat informational bulletin provides information on the proactive alert advanced diagnostics. Proactive Alert monitors the Engine Cranking system and the Fuel Delivery system and if either one of these monitored systems triggers certain performance issues, specific Customer and Dealer Communication are sent.

PIC6186

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that some vehicles may have a radio that turns on unwanted at start up. If the radio was shut off before the vehicle was shut off and at start up the radio turns on, please communicate to the customer that we apologize for this inconvenience, and that General Motors is working on a solution for this concern.

PIC6187

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that some vehicles intermittently the favorites saved from a USB drive or SD card are grayed out and not selectable. Please communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.

PIT5268A

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that some vehicles may have a radio display that is covered when the radio station favorites list is maximized. This is a normal operating characteristic and no repair attempt should be made. The hidden screen functions will operate again after the user minimizes the favorites list by dragging it to the bottom of the display.

PIT5206D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205.

PIT5391A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position, Any of the following Diagnostic Trouble Codes may be set: B1370, B1325, P0650, P263A, P263B, P0513, and/or P0262B. Trucks equipped with 4WD may have a Service 4WD message and Diagnostic Trouble Codes C0364 and/or U0403 may set. Also the sound of a relay clicking while driving or engine stays running with ignition off until door is opened. Technician will inspect all the under-hood fuse block-X50A connectors for any backed out terminals, poor terminal fit and/or bent/twisted terminals. The most common terminals with these issues have been with terminal M5 at connector X4, for circuit 5199 and terminal M7 at connector X2, for circuit 439. Technician will inspect for any backed out terminals, poor terminal fit and/or bent/twisted terminals at the left instrument panel fuse block - X51L. The most common terminals with these issues have been terminal 42 at connector X1, for circuit 5199 and terminal 44 at connector X2, for circuit 1850. Also circuit 5199 will need to be inspected and repaired under the driver?s sill plate.

PIT5403A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

PIT5500

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the vehicles equipped with power folding 3rd row seat and how to diagnosis and repair seats that do not fold down completely or the 60% side does not fold even with the 40% side. Technician will inspect under the 3rd row seat for any objects that will prevent the seat from folding as designed. If the center seat belt from the roof is connected to the seat belt buckle or any of the seat belt buckles not properly stowed in the seat cushion pockets this will prevent the seat from properly folding. Also check under the 60% seat for the wire harness routing. If the harness is not routed correctly or seat connector is not properly attached to the seat bracket the seat will not fold down correctly. If the wire harness or connector is found out of place, reroute the seat harness or use a zip tie for the connector to the bracket. If the concern is still present remove the two rubber bumpers form the 60% seat side rails. After removing the rubber bumpers install a piece of Kent Automotive BRS Flocking tape P/N KT13487, or equivalent, in place of the rubber bumper.

PIC6183

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to help diagnose vehicles that may have a radio inoperative. This concern will last through multiple ignition cycles and is not intermittent. If Service Information diagnostics do not point to the Media Disc Player as being at fault, please continue with normal diagnostics. If SI diagnostics do point to the Media Disc Player being at fault, please do not unplug or remove power from the module or vehicle. Technician will contact General Motors Technical Assistance Center for further assistance.

PIP5382A

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner?s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before you contacting General Motors Product Quality Center.

08-00-89-014B

Service Bulletin/Repair Instructions

This informational bulletin provides information on what is needed to be prepared for TAC, caller preparedness and checklists and contacting U.S. technical Assistance and the use of strategy based diagnostics

PIE0360

Service Bulletin/Repair Instructions

his engineering informational bulletin is requesting information from the field on vehicles that have the condition of intermittent HVAC cooling issues during driving

07-00-89-037I

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on Courtesy Transportation and Roadside Assistance Programs

16-NA-075

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to relearn the power folding mirriors and road test to correct a conditon of power fold away mirriors glass shakes or flutters at normal driving speeds

15-06-03-002B

Service Bulletin/Repair Instructions

This informational bulletin provides information on Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers

PIT5232B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps to diagnose and repair the concern of the display is showing 32° F (0° C) after a battery or reprogramming a module. The outside temperature will begin to update if driven above 20 mph for at least 5 minutes. If the vehicle speed drops below 20 mph, the timer will reset and the display will stop updating. Once the display starts to update it may take several more minutes of driving above 20 mph for the display to fully update. Also if the vehicle is shut off for more than 8 hours the display will update when the ignition is turned on.

PIE0359

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information from th field on vehicles that have the condition of a vehicle crank and no start with DTC P0011 and or P00C6 set

PIP5337C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician a vehicle may have a shake or shudder during light throttle acceleration, between 30 and 65 mph steady driving. Technician will drive the vehicle while monitoring Torque Converter Clutch slip speed. If the Torque Converter Clutch slip speed is in the range of 10 RPM or less the condition is possibly related to engine performance. If the slip speed is beyond 10 rpm or there is shudder during Torque Converter Clutch apply the torque converter should be replaced following the instructions published in Service Information.

08-07-30-026C

Service Bulletin/Repair Instructions

This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary

PIP5130H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.

PIP5232C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.

11-08-49-001P

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on how to take the vehicles out of transport mode for vehicles with the condition of Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing

16-NA-069

Service Bulletin/Repair Instructions

This informational bulletin provides information on If the radar does not see any vehicles, structures, or objects for 15-25 minutes of driving, the system may think its blocked and display the ?Side Object Detection System Disabled? message.

03-00-89-006M

Service Bulletin/Repair Instructions

This informational bulletin provides information on New Vehicle Pre-Delivery Inspection (PDI) - Delivering Quality Vehicles and Generating Higher CSi Scores

03-06-03-004O

Service Bulletin/Repair Instructions

This informational bulletin provides information on Battery Testing and Warranty Replacement Requirements (North America ONLY)

06-00-89-029M

Service Bulletin/Repair Instructions

This informational bulletin provides information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability

09-00-89-002M

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to properly maintain vehicles in the dealer inventory

PIC6176

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician when the radio display is continuously flashing on and off every five seconds the Human Machine Interface will need to be replaced.

PIC6177

Service Bulletin/Repair Instructions

This Preliminary Information communication provides the technician with information on vehicles with navigation radio Regular Production Option Code IO6 or UY4 that defaults to West Virginia instead of Virginia on a manual entry. General Motors engineering is currently working on a solution for this concern.

PIP5382

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Technician will confirm oil level was properly checked per Owner?s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before you contacting General Motors Product Quality Center.

04-00-89-015K

Service Bulletin/Repair Instructions

This warranty informational bulletin provides a list of all the required operating procedures and explains them out to what is acceptable and not.

PIP5189A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLE THAT MAY HAVE BLACK SMOKE ON A COLD START. A DUAL-PULSE INJECTION STRATEGY IS UTILIZED DURING ENGINE COLD START TO REDUCE THE TIME REQUIRED TO BRING THE CATALYTIC CONVERTER UP TO OPERATING TEMPERATURE. THIS SPLIT INJECTION STRATEGY LASTS FOR ABOUT 60 SECONDS ON COLD START. THIS PROCESS MAY CAUSE THE CUSTOMER TO SEE INCREASED BLACK SMOKE DURING COLD START AND SHOULD BE CONSIDERED NORMAL.

16-NA-061

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to trace and complete a wire to wire repair on vehicle that have the concern of Service Tire Monitor System, Tire Pressures Display Dashes, RKE Short Range, No Fob Detected Message

12-03-10-001C

Service Bulletin/Repair Instructions

This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)

PIP5248B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS NEED TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE STALLING SHUDDER AND/OR HARD SHIFTING INTO 1ST GEAR OR REVERSE VIBRATION ON LAUNCH (WITH EXCESSIVE CRANKSHAFT END PLAY). TECHNICIAN WILL TEST TO DETERMINE IF THE CRANK SHAFT END PLAY IS WITHIN SPECIFICATION 0.0015–0.0086 INCH. IF END PLAY IS FOUND TO BE OUT OF SPECIFICATION, REMOVE ENGINE AND INSPECT FOR POSSIBLE CRANKSHAFT THRUST BEARING AND/OR CRANKSHAFT FOR WEAR. INSPECT THRUST BEARING FOR WEAR ON ONE SIDE AND CRANKSHAFT ON THAT “MATING” SURFACE. IF THE THRUST BEARING HAS THREE VERTICAL CHANNELS WORN OFF REPLACE CONNECTING ROD BEARINGS, MAIN BEARINGS, THRUST BEARING AND CRANKSHAFT. IF WORKING ON A CORVETTE THE OIL TANK WITH LINES AND OIL COOLER ARE BOTH REQUIRED TO BE REPLACED IF EQUIPPED.

PIT5496

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS NEED TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE RATTLE OR BUZZ NOISE FROM THE REAR OF THE VEHICLE. TECHNICIAN WILL NEED TO REMOVE RIGHT REAR INNER FENDER WELL AND INSPECT THE REAR AUXILIARY HEATER / EVAPORATOR LINES FOR CONTACTING EACH OTHER. IF THE LINES ARE FOUND TO BE CONTACTING EACH OTHER, LOOSEN THE RETAINING CLAMPS AND REPOSITION LINES TO GAIN CLEARANCE, AND THEN RETIGHTEN RETAINING CLAMPS.

16-NA-055

Service Bulletin/Repair Instructions

This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near

PIP5337B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEP TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE A SHAKE OR SHUDDER DURING LIGHT THROTTLE ACCELERATION, BETWEEN 30 AND 65 MPH STEADY STATE DRIVING. ALSO SHUDDER FEELING THAT MAY BE DESCRIBED AS DRIVING OVER RUMBLE STRIPS OR ROUGH PAVEMENT. TECHNICIAN WILL DRIVE THE VEHICLE AND MONITOR THE TORQUE CONVERTER CLUTCH SLIP. THE TORQUE CONVERTER CLUTCH SLIP SPEED SHOULD BE 10 RPM OR LESS ALSO NOTE IF THE SHUDDER TAKES PLACE DURING TORQUE CONVERTER CLUTCH APPLY. IF THE TORQUE CONVERTER CLUTCH SLIP SPEED IS IN THE RANGE OF 10 RPM OR LESS THE CONDITION IS POSSIBLY RELATED TO ENGINE PERFORMANCE. IF THE SHUDDER IS ONLY PRESENT IN 4 CYLINDER MODE AND TORQUE CONVERTER CLUTCH SLIP IS 10 RPM OR LESS DEEM THE SHUDDER CONCERN NORMAL CHARACTERISTIC OF ACTIVE FUEL MANAGEMENT. IF THE SLIP SPEED IS BEYOND 10 RPM OR THERE IS SHUDDER DURING TORQUE CONVERTER CLUTCH APPLY THE TORQUE CONVERTER WILL NEED TO BE REPLACED.

PIT4211D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE AN OUTSIDE AIR TEMPERATURE INOPERATIVE. TO PERFORM AN INSTANT UPDATE OF THE AMBIENT TEMPERATURE SENSOR, PRESS AND HOLD THE RECIRC BUTTON AND AIR CONDITIONING BUTTON ON THE HEATER-VENT-AIR CONDITIONING CONTROL HEAD SIMULTANEOUSLY. IT IS ALSO POSSIBLE TO PERFORM THIS BY USING A SCAN TOOL IN SPECIAL FUNCTION MODE AND SELECT INSTANT UPDATE.

PIT5291B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLE THAT MAY HAVE WIND WHISTLE NOISE HEARD FROM THE RIGHT OR LEFT REAR QUARTER GLASS AREA WHEN DRIVING AT HIGHWAY SPEEDS OR WITH A CROSS WIND. TECHNICIAN WILL INSPECT THE QUARTER GLASS FOR EXCESSIVE URETHANE. IF EXCESSIVE URETHANE IS FOUND USE A SHARP KNIFE AND CUT OFF THE EXCESSIVE URETHANE. ALSO THE TECHNICIAN WILL INSTALL FOAM TAPE ALONG THE ENTIRE LENGTH OF THE TAIL LIGHT ASSEMBLY.

PIC6170

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS NEED TO DIAGNOSE AND REPAIR VEHICLE THAT MAY HAVE A CONCERN WITH NAVIGATION ICON NOT SHOWING THE CORRECT LOCATION THEN JUMPING TO THE CORRECT LOCATION. THE POSITION INDICATOR MAY SHOW THE VEHICLE TURNING IN THE OPPOSITE DIRECTION OR MAY SHOW THE VEHICLE TRAVELING OFF THE ROAD. TECHNICIAN WILL INSPECT THE HUMAN MACHINE INTERFACE MOUNTING. FOLLOW SERVICE INFORMATION FOR THE CORRECT ORIENTATION OF THE HUMAN MACHINE INTERFACE.

PIP5130G

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN HOW TO DIAGNOSE AND REPAIR A VEHICLE WITH AN ENGINE THAT RUNS WITH AN INTERMITTENT CRANK NO START WITH A DIAGNOSTIC TROUBLE CODE P0011 OR P00C6 CURRENT OR HISTORY. THE CAMSHAFT POSITION ACTUATOR SOLENOID VALVE MAY BE STICKING OR BINDING CAUSING THE VALVE TIMING TO BE RETARDED. DEALER WILL NEED TO CYCLE THE CAMSHAFT POSITION ACTUATOR SOLENOID VALVE BY ENERGIZING IT USING GLOBAL DIAGNOSTIC SYSTEM 2.

PIT5377D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEP NEEDED TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE UNEVEN BRAKE PAD WEAR. TECHNICIAN WILL NEED TO INSPECT AND MEASURE THE BRAKE PADS THICKNESS. ALSO DETERMINE THE CUSTOMER’S DRIVING STYLE. THE DISC BRAKE PADS SHOULD ONLY BE REPLACED IF THE FRICTION SURFACE IS WORN TO WITHIN 2.0 MM (0.079 IN) OF THE MOUNTING PLATES. THE ROTORS AND PADS SHOULD BE REPLACED WITH THE UPDATED PART NUMBER IF THE PADS ARE OUT OF SPECIFICATION, PERFORM NORMAL SERVICE INFORMATION DIAGNOSTICS TO DETERMINE THE CAUSE OF THE CONCERN.

02-08-42-001I

Service Bulletin/Repair Instructions

This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not

11-00-89-005I

Service Bulletin/Repair Instructions

This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only)

PIE0350B

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information from the field on vehicles that have a concern on Bang or Loud Noise with No Forward (Drive) or Reverse Ranges

PIP5230C

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN BEFORE REPLACING THE CRANKSHAFT TO REVIEW THE FOLLOWING. DEALER SHOULD COMPLETE THE SERVICE INFORMATION DIAGNOSTICS AND THE COST COMPARISON WORKSHEET FOR ASSEMBLY REPAIR VS REPLACEMENT. TECHNICIAN WILL USE THE LATEST VERSION OF 09-06-04-026G TO VERIFY THE ECM CALIBRATION IS NOT AN AFTERMARKET CALIBRATION. IF THE CUSTOMER PREFERS TO KEEP THE ORIGINAL NUMBERS MATCHING ENGINE PLEASE CALL TAC FOR REPAIR DIRECTION.

PIT5447A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS NEEDED TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE A RATTLE NOISE FROM THE DASH. TECHNICIAN WILL NEED TO INSPECT FOR THE REAR HEATER PIPES CONTACTING THE PASSENGER SIDE EXHAUST MANIFOLD. IF THE REAR HEATER PIPE IS FOUND TO BE CONTACTING THE EXHAUST MANIFOLD, REPOSITION THE HEATER PIPE SO IT NO LONGER MAKES CONTACT.

PIT5482B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A "SERVICE FRONT CAMERA" MESSAGE ON THE DRIVER INFORMATION CENTER INTERMITTENTLY. WHEN THE TECHNICIAN USES THE SCAN TOOL TO CHECK FOR DIAGNOSTIC TROUBLE CODES A HISTORY U023A AND/OR U026A MAY BE SET IN THE INSTRUMENT PANEL CLUSTER AND/OR BODY CONTROL MODULE. IT IS IMPORTANT THAT THE TECHNICIAN DOES NOT REPLACE THE FRONT VIEW CAMERA MODULE FOR THIS CONCERN. TECHNICIAN WILL REPROGRAM THE FRONT VIEW CAMERA MODULE WITH THE LATEST SOFTWARE USING SERVICE PROGRAMMING SYSTEM.

04-06-01-029H

Service Bulletin/Repair Instructions

This informational bulletin provides information on Unscheduled Supplemental Services (Including Flushing Services and Additives) and Proper Use of GM Simplified Maintenance Schedules (U.S. Only)

PIP5226A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.

PIT5446A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE ONE OR MORE TIRE PRESSURES DISPLAY DASHES, SERVICE TIRE MONITOR SYSTEM MESSAGE, REMOTE KEYLESS ENTRY POOR RANGE OR INOPERATIVE OR “NO FOB DETECTED” MESSAGE OR PASSIVE ENTRY SYSTEM INOPERATIVE (IF EQUIPPED). THE TECHNICIAN MAY FIND ANY OF THE FOLLOWING DIAGNOSTIC TROUBLE CODES SET IN THE BODY CONTROL MODULE ASSOCIATED WITH THE VEHICLE TIRE PRESSURE SENSORS: C0750, C0755, C0760, AND/OR C0765. TECHNICIAN WILL INSPECT THE REMOTE CONTROL DOOR LOCK RECEIVER ANTENNA SYSTEM. BEFORE REPLACING ANY PARTS CHECK THREE LOCATIONS FOR THE SYSTEM BEING UNPLUGGED. THE LOCATIONS WERE THE SYSTEM COULD BE UNPLUGGED ARE ANTENNA AMPLIFIER MODULE DISCONNECTED FROM ANTENNA AT RIGHT REAR QUARTER GLASS, COAX CABLE DISCONNECTED AT THE ANTENNA AMPLIFIER MODULE, AND COAX CABLE DISCONNECTED AT THE REMOTE CONTROL DOOR LOCK RECEIVER.

PIT5361A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE ISSUES WERE THE CUSTOMER WILL NEED INCREASED EFFORT TO DEPRESS THE BRAKE PEDAL. TECHNICIAN MAY FIND FLUID IN THE BRAKE BOOSTER AND/OR THE BOOSTER VACUUM LINE. TECHNICIAN WILL NEED TO REPLACE VACUUM PUMP, BRAKE BOOSTER, MASTER CYLINDER, VACUUM PUMP BELT AND THE VACUUM LINE BETWEEN THE BOOSTER AND THE PUMP.

PIT5482A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A "SERVICE FRONT CAMERA" MESSAGE ON THE DRIVER INFORMATION CENTER INTERMITTENTLY. WHEN THE TECHNICIAN USES THE SCAN TOOL TO CHECK FOR DIAGNOSTIC TROUBLE CODES A HISTORY U023A AND/OR U026A MAY BE SET IN THE INSTRUMENT PANEL CLUSTER AND/OR BODY CONTROL MODULE. IT IS IMPORTANT THAT THE TECHNICIAN DOES NOT REPLACE THE FRONT VIEW CAMERA MODULE FOR THIS CONCERN. TECHNICIAN WILL REPROGRAM THE FRONT VIEW CAMERA MODULE WITH THE LATEST SOFTWARE USING SERVICE PROGRAMMING SYSTEM.

08-08-44-015F

Service Bulletin/Repair Instructions

This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs)

01-08-42-001K

Service Bulletin/Repair Instructions

This informational bulletin provides information on exterior lamp condinsation and replacement guidelines

PIP5261A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A HIGH PITCHED WHINE NOISE FROM THE VEHICLE NOTICED WHEN DRIVING IN AUTO 4WD. WHEN THE TRANSFER CASE CONTROL MODULE HAS TO MOVE THE TRANSFER CASE ACTUATOR MOTOR THE HIGHER CURRENT PASSING THROUGH THE MODULE CAUSES AN "ELECTRONIC BUZZ OR WHINE" WITHIN SOME OF THE CAPACITORS IN THE MODULE THAT CAN BE HEARD BY SOME OF OUR CUSTOMERS. THIS CAN ONLY BE HEARD WITH ALL ACCESSORIES AND HVAC OFF AND ONLY WHEN ACTUATOR MOVEMENT IS REQUIRED. THIS DOES NOT INDICATE A CONCERN WITH THE MODULE AND SHOULD NOT BE REPLACED TO ADDRESS THIS CONCERN.

02-08-98-002F

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to properly repair rust on the hem flange on doors for vehicles that have the condition of rust showing at hem flange

PIE0350A

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information on vehicles that have the condition of Bang or Loud Noise with No Forward (Drive) or Reverse Ranges

16-NA-027

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to replace 4-5-6 clutch hub to correct a condition of No Fourth, Fifth and Sixth Gears and/or Malfunction indicator Lamp Illuminated with DTC P0796

15-NA-007

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to reprogram the transmission control module to correct a firm garage shift, start up clunk, and DTC P16F3 condition

06-08-50-009I

Service Bulletin/Repair Instructions

This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices

03-08-46-004R

Service Bulletin/Repair Instructions

This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)

PIT5401E

Service Bulletin/Repair Instructions

Radio Inoperative with No Communication and DTC U0184

PIP5211D

Service Bulletin/Repair Instructions

Some customers may comment about a rough idle and/or vibration at idle in Drive. This condition may be most noticeable following extended driving, while idling at a stop in Drive. May feel like a lopey or lumpy idle, or may be described as a low idle. This condition will not be present in Park, Reverse, or Neutral. There will not be any DTCs with this concern. When measuring using the vibration analyzer, CH-51450-A (Pico Oscilloscope), With the pico accelerometer positioned on forward end of the seat track; the concern will show in the lateral / cross-car direction as E1.5 (1.5 engine order), in the range of 2-7 mg.

16-NA-011

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to update your apple product to the latest software version to correct a condition of infotainment system will not return to media after bluetooth call ends

PIT5295B

Service Bulletin/Repair Instructions

Unable To Install a CD Or DVD

PIT5490

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

06-06-01-010C

Service Bulletin/Repair Instructions

This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period.

PI1250C

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information on the advanced diagnostic alerts that are sent via onstar, they inform of DTC and indicator lamps that are set within the vehicles.

PIC5614A

Service Bulletin/Repair Instructions

Changing Turn-By-Turn Voice Response To Metric Or English Units

PIP5361

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

PIT5284A

Service Bulletin/Repair Instructions

Rattle Noise From Second Row Seat.

PIE0350

Service Bulletin/Repair Instructions

This engineering informational bulletin is requesting information from dealers regarding the concern of a bang or loud noise with no forward or reverse ranges

05-08-51-001H

Service Bulletin/Repair Instructions

This informational bulletin provides information on removing paint stains on the under side of protective shipping film

03-08-46-004Q

Service Bulletin/Repair Instructions

This informational bulletin provides information regarding Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules

16NA011

Service Bulletin/Repair Instructions

Infotainment System Will Not Return to Media After Bluetooth Call Ends

16NA014

Service Bulletin/Repair Instructions

Delayed Engagement After Sitting With Engine Off

PIP5357

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with engine oil consumption. If published Service Information for oil consumption with no fix. Remove the vacuum line from the back of the vacuum pump and inspect for oil. If oil is found then reference the latest version of PIT5361.

PIT5353A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

PIT5482

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a "Service Front Camera" message on the Driver Information Center. Technician may find Diagnostic Trouble Code U023A and or U026A set in the Instrument Panel Cluster and or Body Control Module. Engineering is aware of this concern and working on new software to resolve this concern. Technician should not replace any parts for this concern.

PIT5377C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the step needed to diagnose and repair vehicles that may have uneven brake pad wear. Technician will need to inspect and measure the brake pads thickness. Also determine the customer?s driving style. The disc brake pads should only be replaced if the friction surface is worn to within?2.0?mm (0.079?in) of the mounting plates. The rotors and pads should be replaced with the updated part number If the pads are out of specification, perform normal Service Information diagnostics to determine the cause of the concern.

PIT5461A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a random infotainment system resets while driving, screen temporarily goes blank and then returns after approximately 5 seconds, radio volume control inoperative, Heater-Vent-Air Conditioning controls function but will not show changes on the display, seek buttons on the front controls will not function, when using CarPlay the map is intermittently bright at night, front pedestrian icon "Check Box" disappears after changing selection, over-temp Pop-up displayed randomly, displays a quick blue screen when shifting to reverse, infotainment system resets when a device with a large amount of songs is connected, XM not showing Station List, and or Radio shows XM Station ID 0 intermittently. Technician should USB program the Human Machine Interface. After USB programming has been completed reprogram the Human Machine Interface module this time using the Service Programming System with the latest calibrations available on TIS2WEB.

PIT4943D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

06-00-89-031D

Service Bulletin/Repair Instructions

OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification

07-08-49-020J

Service Bulletin/Repair Instructions

IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® – The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.

15-NA-082

Service Bulletin/Repair Instructions

Clunking Noise from Front of Vehicle During Turns and/or Bumps Some customers may comment on a clunking noise originating from the front of the vehicle that is more predominant during turns or traveling over bumps. This may be caused by a damaged stabilizer shaft frame bracket. There have been some cases in which the bracket is cracked, as shown. This condition has been found to be the result of insufficient welds between the bracket and frame rail. There have been some cases on older vehicles of corrosion affecting the bracket

15-NA-083

Service Bulletin/Repair Instructions

Recovery Process from a Controller Reprogramming Interruption During service reprogramming of the T87 TCM, some technicians may notice the TCM may fail during the reprogramming event and become unresponsive to the Service Programming System (SPS), unresponsive to the GDS2 tool. This bulletin addresses corrective actions to attempt to recover the module before declaring the TCM as a bad part and replacing. During reprogramming, an interruption can cause the module to lock up. A module reset may recover the TCM

15NA082B

Service Bulletin/Repair Instructions

Clunking Noise from Front of Vehicle During Turns and/or Bumps

PI1187C

Service Bulletin/Repair Instructions

Information on Inside Rear View Mirror and Camera Loose Some customers may comment that the inside rear view mirror or front camera is loose or that the mirror/camera mounting bracket is loose or has fallen off. If a vehicle is encountered with the above condition, do not attempt to reinstall the bracket onto the windshield. The above listed vehicles have a revised bracket design that is not serviceable. It is necessary to replace the windshield glass assembly. The bracket comes installed on the new glass assembly. Refer to Windshield Replacement in SI.

PIE0349

Service Bulletin/Repair Instructions

Engineering Information – Service 4WD Message Displayed and DTC C0398 Condition Important: If the customer did not bring their vehicle in for this concern, DO NOT proceed with this EI. Some customers may comment on a “Service 4WD” message displayed. During diagnosis a technician may find DTC C0398 (Range Actuator Position – Range Position Correlation). Cause GM Engineering is attempting to determine the root cause of the above condition. Engineering has a need to gather information on vehicles PRIOR to repair that may exhibit this condition. As a result, this information will be used to "root cause" the customer's concern and develop/validate a field fix.

PIE0349A

Service Bulletin/Repair Instructions

Engineering Information – Service 4WD Message Displayed and DTC C0398

15-NA-069

Service Bulletin/Repair Instructions

This informational bulletin provides information for technicians on the reuse of fasteners and the proper reading of torque specifications.

PIP5121A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have the oil pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (L83), 5.3L (L86), 6.2L (LV3) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.

PIP5232B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

00-03-10-006L

Service Bulletin/Repair Instructions

This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim.

PIT5214B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

PIT5398A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have the rear vision camera system displaying "Rear Park Assist Symbols Unavailable" and the steering grid lines displayed do not show. If the vehicle is in reverse, the rear vision camera will display "Rear Park Assist Symbols Unavailable" and does not have Regular Production Option Code UD5 or UD7 the radio must be updated using Service Programming System to correct this concern. Some vehicles may not show steering guide/grid lines displayed in the Rear Vision Camera display. Dealer should communicate to the customer that steering guide/grid lines are not available with this base radio Regular Production Option Code (IO3). Some vehicles while in reverse and the rear park assist system detects an object, the warning triangle symbol is displayed on the wrong side of the radio display. Engineering is aware of the issue and updated radio/tuner calibrations will be released shortly.

PIT5481

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. For 2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.

15-06-01-002B

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of engine misfire/tick noise, Malfunction Indicator Lamp (MIL) On, DTC P0300 set.

PIC3100E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

PI1187B

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides windshield replacement information to correct a customer concern that the inside rear view mirror is loose or that the mirror mounting bracket is loose or has fallen off.

PIT5411E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.

15-06-03-002A

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel regarding original equipment battery part numbers and AC Delco replacement battery approved warranty part numbers.

10-00-89-005E

Service Bulletin/Repair Instructions

This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel revised wiring repair labor operations and required additional information.

PIT5405A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician for a reduced power message, steering assist, engine stall or the instrument panel, radio, and or Heater-Vent-Air Conditioning go blank with multiple diagnostic trouble codes. If any of the following diagnostic trouble codes U0073, U0078, U0029, U0028, U0415, U0140, U0126, U0121, U0101, U0100, C0544, U1510, U0073, B127B, B2605, B3600,C0800, U0428, and U0452 set in the vehicle. Check the body control module ground at the G218 location. The front dash insulator mat may be trapped between the ground eyelet and the body stud. Remove the round nut and eyelet and cut the front dash insulator mat away from the ground stud so it no longer interferes with the ground stud and reinstall the eyelet and ground nut.

PIC6049C

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that on November 18th, 2014, part number 23248791 (Wireless Charging Module) will be placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.

PIT5241C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about customers that may request the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup or SUV when the vehicle was not ordered with the option. Dealer should advise the customer it cannot be added to the vehicle.

PIT5288C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.

PIT5307B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a service engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.

PI1344B

Service Bulletin/Repair Instructions

This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.

PIT5379B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a content theft alarm sounding for no apparent reason. Technician may use all published Service Information diagnostics and has not found the cause of the unwanted content theft alarm sounding. Technician should use Global Diagnostic System 2 to review the Body Control Module parameters for "Content Theft Deterrent Trigger History". This is a list of triggers that can cause a content theft alarm sounding. Driver door Passenger door, Left rear door, Right rear door, Rear closure, Tonneau Cover, Hood, Ignition Voltage, Intrusion, Inclination, Telematics enhanced service alarm, Battery reconnect detected, Unauthorized Pulse Width Modulated change, Security Indicates Tamper, and Glass Breakage. If the trigger is an Intrusion inspect for items hanging from the rear view mirror, solar powered dancing characters. When the trigger is a Glass breakage inspect the two rear quarter-panel windows and also in the liftgate glass. The quarter panel windows are attached to the body harness with a connector that looks similar to a 9 volt battery connector inspect them to be fully seated in on the glass. When the trigger is Ignition Voltage/Battery reconnect detected during a cold ambient temperature remote vehicle start event technician should call GM General Motors Technical Assistance Center for further assistance.

PIT5477

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have a squeak, clunk, or knock type noise from the front suspension when hitting bumps. Technician should use published Service Information diagnostics. If the source of the noise has been pinpointed to either the left or right front strut, and if the strut has not been previously disassembled technician will need to contact the General Motors Technical Assistance Center for more information.

PI1002B

Service Bulletin/Repair Instructions

Grease or sealant visible on steering gear - should not be interpreted as leak. Some customers or technicians may comment on seeing grease or sealant on certain locations of the steering gear. The illustrations below include arrows showing the areas on the steering gear that the supplier intentionally applies sealing grease. Any of these locations have the potential of showing visible grease under normal operation.

02-07-30-029Y

Service Bulletin/Repair Instructions

This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).

PIP5344

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have Service Engine Soon Malfunction Indicator Lamp on or reduced power message. Technician may find Diagnostic Trouble Codes P0106, P0107, P0697, P2122, P2123, P2127, P2128 and P2138. Technician should follow published Service Information diagnostics for the Diagnostic Trouble Codes that have set, if it is inconclusive inspect the wiring harness near the left instrument panel junction block. Technician will need to repair the damaged wiring.

PIP5345

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about being to achieve pre-load when setting up the pinion bearing pre-loads during reassembly of the 9.5/9.76 inch rear axles. Technician will need to use pinion gear install washer part number 11609638 onto the pinion shaft between the flange and nut. Tighten the pinion nut until you achieve 10 pound inch or 1.0 newton rotating torque. After the torque has been achieved back the nut off and remove the washer. Tighten the nut back down until you achieve 15 pound inch or 1.7 newton meters for used bearings or 20 pound inch 2.25 newton meters for new bearings.

01-06-01-011I

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

08-08-44-029F

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).

PIP5179B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.

PI1481A

Service Bulletin/Repair Instructions

This preliminary informational bulletin adds the 2016 model year and provides technicians with repair information to correct a customer concern of rough, uneven or irregular horizontal seam on liftgate.

PI0799A

Service Bulletin/Repair Instructions

This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels.

PI1286A

Service Bulletin/Repair Instructions

This preliminary informational bulletin adds the 2016 model year to repair information to correct a customer concern of the hood fluttering, vibrating or displaying visible motion at highway speeds or over rough road surfaces.

PIT5279C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician for vehicles that exhibit a driver?s power memory seat and power adjustable pedals inoperative. Look for poor terminal tension at the left instrument panel fuse block connector X1 terminals 27 and 28. If poor retention is found in these terminals replace them with terminated lead part number 19301761.

PIC5953B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

PIT5392A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a detent / click with a feel of increased resistance when the accelerator pedal is about ¾ of the way. The new accelerator pedal design has a built-in detent position near the last 1/4 of pedal travel. Dealer should communicate to the customer this is a normal operating characteristic of the vehicle and no repair attempts should be performed.

15-NA-030

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on the use of non-GM approved battery chargers and booster packs.

PIP5338

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

15-06-03-001A

Service Bulletin/Repair Instructions

This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.

PIP5199A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with a crankshaft balancer appears to be out of balance or wobbling while watching it with the engine running. Technician will need to check crankshaft balancer run out. If the balancer run out is greater than 0.25mm the crankshaft balancer will need to be replaced.

PIP5213D

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the part restriction on the 8L45/8L90 8 speed and the LCT1000 6 Speed Allison automatic transmission has ended.

PIP5335

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.

PIP5337

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 mph steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will drive the vehicle and monitor the torque converter clutch slip. The torque converter clutch slip speed should be 10 rpm or less also note if the shudder takes place during torque converter clutch apply. If the torque converter clutch slip speed is in the range of 10 RPM or less the condition is possibly related to engine performance. If the shudder is only present in 4 cylinder mode and torque converter clutch slip is 10 rpm or less deem the shudder concern normal characteristic of Active Fuel Management. If the slip speed is beyond 10 rpm or there is shudder during torque converter clutch apply the torque converter will need to be replaced with a updated part number.

PIT5202C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.

PIT5438A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.

PIT5472

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are equipped with Hands Free Power Lift-gate Regular Production Option Code (TC2). Some customers may experience problems with the activation of the lift-gate hands free operation. Dealer will communicate to the customer some tips on the Hands free Lift-gate. The remote keyless entry FOB must be within 3 feet or 1 meter from the bumper. The foot kick is conducted at the direct center of the length of kick zone.

PIT5471

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the lift-gate actuator or strut that is going to be removed or replaced. If the actuator or strut comes loose off a ball stud after it has been reinstalled. Technician will need to replace the ball stud or ball stud w/bracket, the actuator or strut, and ensure the ball socket clips are properly orientated and seated to prevent it from reoccurring.

08-08-44-029E

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).

05-03-07-009H

Service Bulletin/Repair Instructions

This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.

15-05-25-001

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of a Service Stabilitrak message displayed on the Driver Information Center (DIC). During diagnosis, a technician may find DTC C0196-5A set in the Electronic Brake Control Module (EBCM).

PIT5467

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that the engine idle hours are incorrect and the engine hours are correct. Engineering is aware of this issue and working on a fix.

PIT5468

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about a connectivity concern with Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken place. Technician should delete all Bluetooth pairings and then reboot the Bluetooth device and the vehicle. After the vehicle and radio is booted back up repair the Bluetooth device.

PIP5325

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.

PIP5330

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.

PIT5049B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.

PIT5461

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a random infotainment system resets while driving, screen temporarily goes blank and then returns after approximately 5 seconds, radio volume control inoperative, Heater-Vent-Air Conditioning controls function but will not show changes on the display, seek buttons on the front controls will not function, when using CarPlay the map is intermittently bright at night, front pedestrian icon "Check Box" disappears after changing selection, over-temp Pop-up displayed randomly, displays a quick blue screen when shifting to reverse, infotainment system resets when a device with a large amount of songs is connected, XM not showing Station List, and or Radio shows XM Station ID 0 intermittently. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

PIP4112Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

PIT5448B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

PIP5323

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with misfires or roughness on cold start up. Technician may find a Diagnostic Trouble Code P0300 stored. Technician will add coolant dye to the system, run engine through warm up, pressurize the cooling system on a cold soak engine and inspect the suspect cylinder with a bore scope for coolant dye evidence. If coolant is found in the cylinder do not replace the cylinder head because that will not repair this concern. Dealer will need to contact General Motors Product Quality Center for engine replacement.

PI0564H

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

SB-08-24-15

Service Bulletin/Repair Instructions

GENERAL MOTORS: PARTS FOR MOST VEHICLES, CLUTCH, MASTER CYLINDER ASSEMBLY ARE, REQUIRED AND REQUESTED, TO BE RETURNED AND NEED TO REORDER REPLACEMENT PARTS USING SAME PART NUMBERS. *PE

15-00-89-005

Service Bulletin/Repair Instructions

This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).

PIP5230B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician before replacing the crankshaft to review the following. Dealer should complete the Service Information diagnostics and the Cost Comparison Worksheet for Assembly Repair vs. Replacement. Technician will use the latest version of 09-06-04-026G to verify the Engine Control Module calibration is not an aftermarket calibration. If the customer prefers to keep the original numbers matching engine please call General Motors Technical Assistance Center for repair direction.

10-08-110-001D

Service Bulletin/Repair Instructions

This informational bulletin provides information on the proper use of GM floor mats.

00-06-01-026G

Service Bulletin/Repair Instructions

This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.

PIP5279A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Codes P0089, P127C, P127D, P0192, P0193, P228C, P228D, and P006C. Technician should follow published Service Information diagnostics for the Diagnostic Trouble Codes that are stored. If Service Information does not lead to a repair for the concern, the fuel rail pressure sensor should be replaced.

07-00-89-037H

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on courtesy transportation and roadside assistance programs.

09-09-40-001C

Service Bulletin/Repair Instructions

This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.

PIP-5230-B

Service Bulletin/Repair Instructions

GMC/CHEVROLET/CADILLAC: INFORMATION PROVIDED ON SOME VEHICLES AND SUV, FOR REPLACEMENT OF CRANKSHAFT, FOR ENGINE REPAIR AND OIL TANK AND LINES WOULD BE REPLACED ON DRY SUMP ENGINES WHEN REPAIRING AND/OR REPLACING. MODEL 2014-16 CORVETTE, SILVERADO, SIERRA, 2016 CTS-V, 2015-16 ESCALADE, SUBURBAN, TAHOE, YUKON, YUKON XL. *PE

SB-00-06-01-026G

Service Bulletin/Repair Instructions

GENERAL MOTORS: IN SOME VEHICLES AND TRUCKS, WHEN TRANSFERRING INTAKE MANIFOLD TO REPLACE AN ENGINE LONG SERVICE BLOCK, DUE TO INTERNAL DAMAGE, EXTREME CAUTION MUST BE TAKEN FOR COMPONENT DEBRIS VIA BROKEN, BENT OR MISSING INTAKE VALVES. *PE

09-00-89-002L

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer inventory.

PIC5932A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.

PIP5213C

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the LCT1000 6 Speed Allison, 8L90 and 8L45 8 speed automatic transmission as well as the transmission control module is on restriction through General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.

09-06-04-026K

Service Bulletin/Repair Instructions

This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline engines using Tech 2® or GDS 2 (U.S. and Canada).

99-01-39-004G

Service Bulletin/Repair Instructions

This technical bulletin provides repair information for the correction of a customer concern of short duration musty odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.

PIT5259B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that the door striker cover will be shipped with the vehicle from the assembly plant. Technician is to make sure the rounded side of the cover is positioned towards the outboard side of the vehicle.

03-06-03-003E

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on ACDelco® replacement battery warranty procedures.

PIT5443

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician of a concern where the Onstar® menu is missing from the radio display. Pressing the white Onstar® push to talk button and say hide Onstar® menu will hide the menu and saying unhide menu will make the menu come back again.

03-00-89-006L

Service Bulletin/Repair Instructions

This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores.

PIP4648C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that replacement transfer case halves will not be threaded. No additional thread tapping will be necessary to assemble the transfer case as the attaching metric bolts are self-tapping. Drive the bolts into the new case and torque them to specification.

01-08-51-003E

Service Bulletin/Repair Instructions

This informational bulletin provides recommendations and product information for application of anti-corrosion materials

05-06-04-022M

Service Bulletin/Repair Instructions

This informational bulletin provides information on TOP TIER Detergent Gasoline and available retail brands.

03-06-03-004N

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).

PI1250B

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides information on the introduction of the Advanced Diagnostics - Proactive Alerts available on many models.

02-00-89-002O

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on when and how to submit a Field Product Report (FPR) (U.S. Dealers Only).

PIC6107

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.

99-00-89-019M

Service Bulletin/Repair Instructions

This informational bulletin provides dealership personnel with Global Warranty Management (GWM), Warranty Parts Center (WPC), and Parts Return Program information.

09-00-89-002K

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer inventory.

15-00-89-004A

Service Bulletin/Repair Instructions

This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.

00-06-01-026F

Service Bulletin/Repair Instructions

This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.

PI0091B

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides repair information to correct a customer concern of Iitermittently key will not rotate in door or ignition lock cylinder.

02-08-42-001H

Service Bulletin/Repair Instructions

This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.

11-08-49-001O

Service Bulletin/Repair Instructions

This technical bulletin provides repair procedure information to correct a customer concern of Transport Mode On message displayed in Driver Information Center (DIC) and/or battery light is flashing.

15-00-89-004

Service Bulletin/Repair Instructions

This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage.

PIT5399

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

13-08-116-001B

Service Bulletin/Repair Instructions

The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

PI1440

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides technicians with diagnostic tips for a customer concern of odor emanating from HVAC system.

04-00-89-015J

Service Bulletin/Repair Instructions

This warranty administration bulletin communicates GM required operating procedures (U.S. only) for service operations.

09-00-89-016D

Service Bulletin/Repair Instructions

This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications.

12-06-01-008B

Service Bulletin/Repair Instructions

This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).

15-00-89-003

Service Bulletin/Repair Instructions

This informational bulletin provides information on dealer reimbursement procedures for Customer Assistance Center (CAC) Tier 1 and Tier 2 empowerment tools: diagnostic fee, short term rental, and up-front towing (U.S. only).

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.

2016 Gmc Yukon Service Bulletins: 1401 bulletins | CarFathom