Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
Z05 OL
Warranty Program/Extension
Certain vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years with unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.
26-BD-002H DN
Warranty Program/Extension
Some Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use and is valid for original and subsequent owners.
26-BD-002H TSB
Warranty Program/Extension
Certain Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use and is valid for original and subsequent owners. The warranty extension does not apply to any vehicle that has ever been declared a total loss or sold for salvage by a financial institution or insurer or has a branded or similar title under any state’s law.
DTN DCS
Other
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent safety advisory regarding dangerous, counterfeit driver‑side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or non‑certified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.
DTN DL
Other
The National Highway Traffic Safety Administration (NHTSA) has identified the presence of substandard and dangerous driver’s-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.
P33 OL
Other
In response to this trend, we engineered a software upgrade that addresses the social media theft method and made it available to owners of eligible models free of charge at authorized Hyundai dealers since early 2023. In addition to the anti-theft software, we’ve developed a new zinc-reinforced ignition cylinder protector hardware upgrade that can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because your Hyundai vehicle with the VIN listed above (“Subject Vehicle”) was not factory-equipped with an engine immobilizer and was previously eligible for the software upgrade, you are now eligible until March 31, 2027 to have the ignition cylinder protector installed — if you request it — at no cost to you through an authorized Hyundai dealership.
25-01-089H DCS
Other
Upon customer's request ONLY, the Technical Service Bulletin (TSB) 25-01-089H provides the service procedure for installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows. This repair procedure is being provided in addition to the previous Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1).
25-01-089H DN
Other
In addition to the Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1), a zinc reinforced ignition cylinder protector hardware upgrade is being made available to customers upon request. This supplemental security measure is to be installed at the ignition switch location and provides additional protection against the social media theft method. Vehicles not equipped with an immobilizer during production at the factory are eligible. The repair procedure shall be performed and claimed upon customer request only. Any future repairs to these vehicles in which an installed ignition cylinder protector impacts required parts and/or labor, shall be covered by HMA. Please see TSB 25-01-089H for details.
25-01-089H TSB
Other
This bulletin provides the service procedure for installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows.
25-BD-012H TSB
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
25-01-054H
Service Campaign
Certain 2017-2019MY Elantra (AD, ADA) vehicles equipped with 2.0L ATK engines may be unable to complete diagnosis of the OBD-II Fuel System Readiness Monitor. This bulletin provides instructions to perform a software update for the Engine Control Module (ECM) to revise control logic.
25-01-054H DN
Service Campaign
Certain 2017-2019MY Elantra (AD, ADA) vehicles equipped with 2.0L ATK engines may be unable to complete diagnosis of the OBD-II Fuel System Readiness Monitor. This bulletin provides instructions to perform a software update for the Engine Control Module (ECM) to revise control logic.
25-BD-004H OL
Warranty Program/Extension
Certain 2015 – 2018 model year Elantra, 2015 – 2019 model year Sonata, 2017 – 2021 model year Tucson, 2017 – 2018 model year Santa Fe Sport, 2019 model year Santa Fe, 2021 – 2023 model year Santa Fe Hybrid, and 2020 – 2023 model year Palisade vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years with unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.
25-BD-004H EM
Warranty Program/Extension
Some vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years and unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.
25-BD-004H DN
Warranty Program/Extension
Certain Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has been previously declared a total loss, and/or sold for salvage by a financial institution or insurer, and/or has a branded or similar title under any state’s law.
25-BD-004H TSB
Warranty Program/Extension
Description: Certain Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has ever been declared a total loss or sold for salvage by a financial institution or insurer, or has a branded or similar title under any state’s law.
25-01-024H-1 TSB
Service Campaign
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Bluelink Service functions. This may be due to an irregular disconnection on Verizon’s communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.
25-01-024H EM
Service Campaign
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Bluelink Service functions. This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.
25-01-024H TSB
Service Campaign
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Bluelink Service functions. This may be due to an irregular disconnection on Verizon’s communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.
24-01-050H-1
Service Campaign
This bulletin provides instructions to update the 4th generation AVN head unit software to ensure the SIM Over The Air function for the Bluelink service is operating properly.
24-01-050H
Service Bulletin/Repair Instructions
This bulletin provides instructions to update the 4th generation AVN head unit software to ensure the SIM Over The Air function for the Bluelink service is operating properly.
24-01-009H-1
Service Campaign
A class settlement against Hyundai Motor America (“HMA”) that had alleged that certain 2011 – 2022 model year Hyundai vehicles that were not equipped with an engine immobilizer (called the “Class Vehicles”) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional “turn-key-to-start” ignition systems.
24-AT-002H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and replace, if necessary, an automatic transmission with Incorrect Ratio DTC (transmission clutch slip in gear above limit) listed on Page 2.
24-BD-001H
Service Bulletin/Repair Instructions
This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.
24-01-009H
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.
23-01-014H-6
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
23-01-014H-5
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
23-EM-005H
Service Bulletin/Repair Instructions
This bulletin provides important checkpoint guidelines when performing engine oil and filter change services.
23-BE-010H
Service Bulletin/Repair Instructions
Some models from service campaign 993 (IBU/BCM Software Update and Decals Application) equipped with the Hyundai OEM remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.
23-01-014H-4
Service Bulletin/Repair Instructions
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
23-BD-007H
Service Bulletin/Repair Instructions
Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
23-01-014H-3
Service Bulletin/Repair Instructions
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
23-01-014H-2
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993) in response to an increase in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.
23-01-014H-1
Service Bulletin/Repair Instructions
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
23-01-014H
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993) in response to an increase in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. Please note that all Hyundai vehicles meet or exceed Federal Motor Vehicle Safety Standards. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.
23-BD-002H
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
22-BD-010H
Service Bulletin/Repair Instructions
Certain 2017-2018MY Elantra (ADa), Sonata (LFa), and Santa Fe Sport (AN) vehicles manufactured by Hyundai Motor Manufacturing Alabama (âHMMAâ) may exhibit peeling or bubbling of the white paint in various areas of the vehicle, most commonly on or around the hood, fender, and roof. The paint warranty coverage for these vehicles with white exterior paint has been extended to the following: ⢠2017MY vehicles â 6 years with unlimited miles from the date of original retail delivery or date of first use, whichever occurred first, and is valid for original and subsequent owners ⢠2018MY vehicles â 5 years with unlimited miles from the date of original retail delivery or date of first use, whichever occurred first, and is valid for original and subsequent owners
22-EM-010H
Service Bulletin/Repair Instructions
Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement.
22-GI-006H
Service Bulletin/Repair Instructions
Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.
218/231 amend
Service Bulletin/Repair Instructions
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.
22-ST-005H
Service Bulletin/Repair Instructions
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.
21-01-080H
Service Bulletin/Repair Instructions
When asked to provide the Modem Information, the Universal Subscriber Identity Module (USIM) information is not available. This bulletin describes the 3-part Software to correct this condition and activate Blue Link Services.
DBP972
Service Bulletin/Repair Instructions
When asked to provide the Modem Information, the Universal Subscriber Identity Module (USIM) may not be available. This TSB# 21-01-080H describes the 3-part software to correct this condition and activate Blue Link Services.
21-01-064H
Service Bulletin/Repair Instructions
This bulletin provides information related to an Electronic Control Module (ECM) software update to revise control logic for completion of OBD-II Fuel System Readiness Monitor diagnosis.
968DBP20211116
Service Bulletin/Repair Instructions
This update includes information related to Electronic Control Module (ECM) software to revise control logic for completion of OBD-II Fuel System Readiness Monitor diagnosis.
21-ST-003H
Service Bulletin/Repair Instructions
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing
21-AT-013H
Service Bulletin/Repair Instructions
Certain vehicles (listed below) equipped with 7-speed Dual Clutch Transmission (DCT) may exhibit abnormal vibration at low speeds. This bulletin outlines the procedures for diagnosing and replacing the Double Clutch, including a Transmission Control Unit (TCU) software update.
21-BD-006H
Service Bulletin/Repair Instructions
Certain Elantra (AD/ADa) and Tucson (TL) vehicles may experience an internal or external door handle being inoperative or requiring repeated attempts to open the door. If this condition occurs, replace the affected door latch. The warranty coverage for the door latch has been extended to 10 years (unlimited mileage) from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
21-EM-004H
Service Bulletin/Repair Instructions
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.
21-BR-002H
Service Bulletin/Repair Instructions
This bulletin provides best practice recommendations when performing brake service procedures.
21-EM-003H
Service Bulletin/Repair Instructions
This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below.
20-BR-002H
Service Bulletin/Repair Instructions
This bulletin describes the procedure to inspect and identify fluid which may appear around the brake caliper area.
20-SS-004H
Service Bulletin/Repair Instructions
This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. For all wheel/tire balance claims, the âTire Balance Data Sheetâ must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.
20-ST-003H-1
Service Bulletin/Repair Instructions
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.
20-ST-001H-1
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-ST-003H
Service Bulletin/Repair Instructions
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.
20-BD-014H
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.
20-AT-018H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with the following symptoms and DTC, follow the Service Procedure on Page 3. ï· Check Engine light on ï· DTC P0880/P088000 - TCM Power signal error open/short ï· Transmission stuck in 4th gear fail-safe ï· Harsh shift into Drive and Reverse
20-SS-002H(1)
Service Bulletin/Repair Instructions
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance.
20-BD-007H-1
Service Bulletin/Repair Instructions
This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products.
20-EE-003H
Service Bulletin/Repair Instructions
This bulletin provides information on identifying dealer stock vehicles with either: ⢠A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. ⢠A 30 Day alert - vehicle has not started and reported an SOC in 30 days.
20-AT-016H
Service Bulletin/Repair Instructions
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions:
20-AT-015H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the oil pressure harness.
20-AT-012H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a (Check Engine Light on) and one or more of the DTC listed below, follow the repair procedure and replace the input/output speed sensor and oil pressure harness.
20-BD-007H
Service Bulletin/Repair Instructions
This bulletin describes the general guidelines to disinfect and protect vehicle interior surfaces using certain safe chemical products.
20-EE-002H(1)
Service Bulletin/Repair Instructions
This bulletin describes the mandatory procedure to submit battery test data electronically for battery warranty claims by running the GDS Battery Claim App. The App must be run right after an incident battery is removed from the vehicle or after a battery charge is completed which qualifies for a warranty. It must be run at any time between RO open and close dates.
20-AT-007H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-FL-001H
Service Bulletin/Repair Instructions
Some 2017MY Elantra (AD/ADA) vehicles equipped with 2.0L engine may experience Malfunction Indicator Light illumination with DTC P0300/P0301/P0302/P0303/P0304 (Cylinder âXâ â misfire detected). The bulletin provides information on the repair procedure.
20-SS-001H
Service Bulletin/Repair Instructions
This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years.
20-BE-001H
Service Bulletin/Repair Instructions
This bulletin provides guidelines to inspect the USB, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.
20-ST-001H
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-AT-001H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
19-AT-021H-1
Service Bulletin/Repair Instructions
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.
19-AT-024H
Service Bulletin/Repair Instructions
If you are servicing a vehicle with the DTC or symptoms listed below, refer to the Service Procedure to diagnose the condition. ? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear indication in cluster ?Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.
19-BE-011H-1
Service Bulletin/Repair Instructions
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.
19-BE-015H-1
Service Bulletin/Repair Instructions
This bulletin contains information regarding the clock display on certain Navigation (AVN 4.0) head units. This procedure is specifically for the clock date and time not displaying which started appearing around August 17, 2019. Other similar concerns which were opened before this date are a different root cause and will not be resolved by this information. An example of the clock concern is shown in the screenshot below:
19-GI-006H
Service Bulletin/Repair Instructions
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.
19-AT-016H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
19-AT-012H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
19-AT-010H
Service Bulletin/Repair Instructions
This bulletin provides a procedure to transfer pressure data to the ECU/TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality.
19-ST-001H
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
19-FL-003H
Service Bulletin/Repair Instructions
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.
19-BE-004H
Service Bulletin/Repair Instructions
This bulletin provides information on the serviceable parts for the outside mirror assembly. When diagnosing and repairing the outside mirror, do not replace the entire assembly. Refer to page 2 of this TSB for replacement of individual parts.
19-AT-002H
Service Bulletin/Repair Instructions
Certain vehicles (listed below) equipped with 7-speed Dual Clutch Transmission (DCT) may exhibit an abnormal vibration at low speeds. This bulletin outlines the procedures for diagnosing and replacing the Double Clutch, including a Transmission Control Unit (TCU) software update.
5NP-Z3A5R-02
Service Bulletin/Repair Instructions
This bulletin provides the procedure to update the TCU (Transmission Control Unit) in certain vehicles (listed Below) when replacing the Dual Clutch Transmission (DCT) with updated clutch material. This bulletin also provides a method of identifying transmissions with the updated F850 clutch material.
5NP-R9D7V-01
Service Bulletin/Repair Instructions
This bulletin provides information on certain 2017-2018 model year Elantra (AD/ADA) 2.0L vehicles to update the ECM (Engine Control Module), update the HVAC ECU, and to update the engine coolant temperature gauge of the Instrument Cluster for improving heater performance.
5NP-X9G4F-09
Service Bulletin/Repair Instructions
This bulletin describes the proper steps to identify and correct a symptom with a "Subscription Updated" or "Loading" pop-up message shown (intermittently) after every Head Unit boot up.
5NP-Y4N3B-08
Service Bulletin/Repair Instructions
This bulletin describes the procedure to diagnose the vehicle?s D-Audio unit as a result of the inability to set the clock or view it on the top of the screen.
5NP-C5F9C-08
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a Check Engine light on and one or more of the DTC listed below, follow the repair procedure and replace the oil pressure harness.
5NP-P4Y7D-08
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a ?Check Engine Light on? and one or more of the DTC listed below, follow the repair procedure and replace the input/output speed sensor and oil pressure harness.
5NP-M5G2M-08
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a complaint of ?Check Engine Light on? and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
5NP-G7C2D-06
Service Bulletin/Repair Instructions
This bulletin describes the procedure to determine if the vehicle?s display audio radio unit needs to be replaced as a result of the clock time inaccuracy (i.e. Resets overnight, loses/gains time).
5NP-H6P9S-06
Service Bulletin/Repair Instructions
On some Elantra (MD/UD), Elantra GT (GD) and Veloster (FS) vehicles, a noise may develop in the steering rack. This bulletin does not address any steering function related concerns. This bulletin provides information on replacement of the steering rack support yoke assembly.
5NP-F6W6P-05
Service Bulletin/Repair Instructions
The shift lever on some 6-speed vehicles may intermittently not shift out of Park. This bulletin provides the diagnostic procedures to correct this condition.
5NP-P5L7D-05
Service Bulletin/Repair Instructions
If you are servicing a vehicle with a harsh and/or delayed shift, use the GDS as shown in the Service Procedure to measure shift engagement time.
5NP-A2Y3D-05
Service Bulletin/Repair Instructions
This bulletin provides a procedure for replacing the thermostat on certain 2017 Elantra vehicles. The thermostat may not function properly and may result in Diagnostic Trouble Code P0128. Replacement of thermostat is required even without a P0128 code.
5NP-G7W3S-05
Service Bulletin/Repair Instructions
If a vehicle exhibits a harsh and/or delayed shift, follow the Service Procedure below to measure the shift engagement time.
5NP-B7C4X-03
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a shift lever that is difficult to move, follow the Service Procedure in this bulletin.
5NP-T5B2D-02
Service Bulletin/Repair Instructions
This bulletin describes the procedure to determine if the vehicle?s head unit needs to be replaced as a result of the system frequently losing a Bluetooth connection with Apple iPhone devices.
5NP-G8S6L-01
Service Bulletin/Repair Instructions
This bulletin describes the procedure to determine if the vehicle's navigation unit needs to be replaced as a result of the inability to set the clock or view it on the top of the screen.
5NP-N5K9P-01
Service Bulletin/Repair Instructions
This bulletin describes the procedure to inspect and replace the floor console armrest if the cover material is found to be peeling.
5NP-A7F2T-11
Service Bulletin/Repair Instructions
On some Elantra (AD) vehicles, a noise may develop in the upper side of the front strut mount. There are no vehicle performance issues associated with the noise. This bulletin provides information on replacement of the front strut nut.
5NP-F9U6L-11
Service Bulletin/Repair Instructions
This bulletin describes the procedure to inspect and replace the floor console armrest if the cover material is found to be peeling.
5NP-R3A7B-11
Service Bulletin/Repair Instructions
Hyundai Motor America is conducting a Service Campaign to inspect and (if necessary) replace the console armrest cover on certain 2017 Elantra vehicles. Service Campaign T2I provides a service procedure to inspect the console armrest cover.
5NP-Z6F3A-11
Service Bulletin/Repair Instructions
Before installing an automatic transmission, check the depth of the torque converter in the case to confirm the torque converter is fully installed in the transmission. If this is not done, the oil pump may be damaged.
5NP-V3F8T-09
Service Bulletin/Repair Instructions
If you are servicing a vehicle with the DTC or symptoms listed below, refer to the Service Procedure to diagnose the condition. ? Diagnostic trouble codes: ? P0705 - Range switch sensor circuit ? P0706 - Range switch range/performance ? P0707 - Range switch - open circuit ? P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ? Malfunction Indicator Light (MIL) illuminated ? 4th gear fail-safe ? No gear indication in cluster ? Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.
5NP-H7S5M-07
Service Bulletin/Repair Instructions
Some vehicles with Neutral Control may experience a rough idle in Drive after decelerating to a stop when Neutral Control is enabled. This bulletin provides a diagnosis and repair procedure for this condition. Neutral Control is a fuel efficiency strategy that shifts the transmission into neutral at a stop. The transmission shifts into first gear when the brake pedal is released. Neutral Control is disabled when the shift lever is moved to the Manual Mode position or with the A/C on in some models.
5NP-H3R3S-07
Service Bulletin/Repair Instructions
This bulletin provides information related to the Engine Control Module (ECM) software update for reacceleration and tip-out shift shock improvement.
5NP-U6X2Q-07
Service Bulletin/Repair Instructions
Hyundai Motor America has added retailed vehicles to Service Campaign T1D. This Service Campaign provides a service procedure to update the ECM on certain 2017 Model Year Elantra with 2.0L MPI engines.
5NPP6K4H02
Service Bulletin/Repair Instructions
Hyundai Motor America is conducting a Service Campaign to inspect and (if necessary) replace the console armrest cover on certain 2017 Elantra vehicles. Service Campaign T1P provides a service procedure to inspect the console armrest cover.
5NPS8N7M02
Service Bulletin/Repair Instructions
This bulletin describes the procedure to inspect and replace the floor console armrest if the cover material is found to be peeling. This peeling condition was caused during the cover material cutting process.
5NP-D5V9P-01
Service Bulletin/Repair Instructions
HYUNDAI MOTOR AMERICA IS CONDUCTING A SERVICE CAMPAIGN TO INSPECT AND IF NECESSARY REPLACE THE SD CARD ON CERTAIN 2016-17 MODEL YEAR SONATA AND ELANTRA VEHICLES. SERVICE CAMPAIGN T1M PROVIDES A PROCEDURE TO INSPECT THE SD CARD.
5NP-D9L7X-01
Service Bulletin/Repair Instructions
THIS BULLETIN DESCRIBES THE SD CARD INSPECTION AND REPLACEMENT PROCEDURE FOR CERTAIN SONATA AND ELANTRA NAVIGATION SYSTEMS.
5NP-G5N9M-01
Service Bulletin/Repair Instructions
IF YOU ARE SERVICING AN APPLICABLE VEHICLE WITH A COMPLAINT OF CHECK ENGINE LIGHT ON AND ONE OR MORE OF THE DTC LISTED BELOW, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE RELATED SOLENOID AND OIL PRESSURE HARNESS.
5NP-W2R7L-12
Service Bulletin/Repair Instructions
This bulletin describes the procedure to evaluate warped floor mats.
5NP-Y4X8Z-12
Service Bulletin/Repair Instructions
This bulletin describes the procedure to evaluate warped floor mats.
5NP-D8E4D-12
Service Bulletin/Repair Instructions
HYUNDAI MOTOR AMERICA IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE OVERHEAD CONSOLE LIGHT BULBS ON CERTAIN DEALER STOCK 2017 MODEL YEAR ELANTRA VEHICLES. SERVICE CAMPAIGN T1F PROVIDES A PROCEDURE TO REPLACE THE OVERHEAD CONSOLE LIGHT BULBS.
5NP-S2K8T-12
Service Bulletin/Repair Instructions
Hyundai Motor America is conducting a Service Campaign to inspect and (if necessary) replace the floor mat on certain dealer stock Elantra vehicles. Service Campaign T1G provides a procedure to inspect the floor mats.
5NP-T2X4B-12
Service Bulletin/Repair Instructions
Hyundai Motor America is conducting a Service Campaign to update the ECM on certain dealer stock 2017 Model Year Elantra with 2.0L MPI engine. Service Campaign T1D provides a procedure to update the ECM.
5NP-Y2M6S-12
Service Bulletin/Repair Instructions
This bulletin provides information related to the ECM software update for reacceleration and tip-out shift shock improvement.
5NP-H5D3F-12
Service Bulletin/Repair Instructions
On certain 2017 Elantras the overhead console lamp intermittently does not turn ON.
5NP-H8T3R-10
Service Bulletin/Repair Instructions
THIS BULLETIN PROVIDES A PROCEDURE TO TRANSFER PRESSURE DATA TO THE PCM USING GDS MOBILE. THIS PROCEDURE IS NECESSARY TO REDUCE THE TCM LEARNING TIME AND IMPROVE THE SHIFT QUALITY.
5NP-S9D9P-10
Service Bulletin/Repair Instructions
THIS BULLETIN PROVIDES INFORMATION ON COMPONENTS, ATTRIBUTES, AND PRECAUTIONS OF THE 7-SPEED DRY-TYPE DUAL CLUTCH TRANSMISSION (DCT).
5NP-B3N9F-09
Service Bulletin/Repair Instructions
THIS BULLETIN PROVIDES INFORMATION FOR NEW SOFTWARE TO UPDATE THE NAVIGATION AND DISPLAY AUDIO SYSTEM TO INCLUDE THE APPLE CARPLAY AND ANDROID AUTO FEATURE. THIS BULLETIN DESCRIBES HOW TO TRANSFER THE UPDATE SOFTWARE TO A STORAGE DRIVE (USB OR SD CARD) AND PERFORM THE SOFTWARE INSTALLATION INTO THE AUDIO SYSTEM.
5NP-D3F4K-09
Service Bulletin/Repair Instructions
HYUNDAI MOTOR AMERICA HAS ADDED ADDITIONAL VEHICLES TO SERVICE CAMPAIGN TLL. SERVICE CAMPAIGN TLL PROVIDES A PROCEDURE TO REPLACE THE ENGINE THERMOSTAT ON CERTAIN 2017 MODEL YEAR ELANTRA VEHICLES.
5NP-Q4F3B-09
Service Bulletin/Repair Instructions
HYUNDAI MOTOR AMERICA IS CONDUCTING A SERVICE CAMPAIGN TO VERIFY PROPER INSTALLATION OF THE OUTSIDE DOOR HANDLE CAP SCREW ON CERTAIN 2017 MODEL YEAR ELANTRA VEHICLES. SERVICE CAMPAIGN TNN PROVIDES A PROCEDURE TO VERIFY PROPER INSTALLATION OF THE OUTSIDE DOOR HANDLE CAP SCREW.
5NP-V2N3H-09
Service Bulletin/Repair Instructions
THIS BULLETIN PROVIDES A PROCEDURE FOR REPLACING THE THERMOSTAT ON CERTAIN 2017 ELANTRA VEHICLES. THE THERMOSTAT MAY FUNCTION IMPROPERLY AND MAY RESULT IN DIAGNOSTIC TROUBLE CODE P0128. NO DRIVABILITY ISSUES ARE ASSOCIATED WITH THIS CONDITION.
5NP-V5B5E-09
Service Bulletin/Repair Instructions
CERTAIN 2017 ELANTRA (ADA) MAY HAVE LOWER THAN SPECIFIED TORQUE ON THE FASTENER SECURING THE OUTSIDE DOOR HANDLE(S). THIS MAY LEAD TO IMPROPER OPERATION OF THE OUTSIDE DOOR HANDLE(S). THIS BULLETIN DESCRIBES THE PROCEDURE TO CHECK AND TIGHTEN THE OUTSIDE DOOR HANDLE CAP SCREWS AS REQUIRED.
5NP-Q7S7E-09
Service Bulletin/Repair Instructions
THE SHIFT LEVER ON SOME 6-SPEED VEHICLES MAY INTERMITTENTLY NOT SHIFT OUT OF PARK. THIS BULLETIN PROVIDES THE DIAGNOSTIC PROCEDURES TO CORRECT THIS CONDITION.
5NP-M5P8Y-07
Service Bulletin/Repair Instructions
THIS TSB PROVIDES INTRUCTION ON UPDATING THE NAVIGATION/AUDIO SYSTEM TO INCLUDE APPLE CARPLAY AND ANDROID AUTO FEATURES.
5NP-M5A6D-09
Service Bulletin/Repair Instructions
SOME ELANTRA 2.0L (ADA) VEHICLES MAY EXPERIENCE AN INOPERABLE AIR CONDITIONING SYSTEM WITH THE VENTED AIR BEING WARMER THAN NORMAL WHEN THE A/C IS SELECTED IN THE COLD TEMPERATURE SETTING. THIS CONDITION MAY BE DUE TO AN A/C REFRIGERANT LEAK FROM A PORTION OF THE SUCTION & LIQUID TUBE ASSEMBLY.
5NP-Y5X5D-09
Service Bulletin/Repair Instructions
HYUNDAI MOTOR AMERICA IS LAUNCHING RECALL 144 FOR A TOTAL OF 33 VEHICLES. 2015/2016 MY SONATAS VEHICLES (30 UNITS), AND 2016 MY SONATA HYBRID VEHICLE (ONE UNIT), AND 2017 MY ELANTRA (TWO UNITS) VEHICLES FOR REPLACEMENT OF THE DRIVERS FRONTAL AIRBAG MODULE.
5NP-F9E3D-09
Service Bulletin/Repair Instructions
THIS BULLETIN DESCRIBES STEPS TO ACTIVATE APPLICABLE VEHICLES WITH NAVIGATION OR DISPLAY AUDIO RADIOS THAT HAVE BEEN DE-ACTIVATED FOR THE FOLLOWING REASONS: H A CUSTOMER WHO INITIALLY WAIVES BLUE LINK ENROLLMENT, AND THEN DECIDES TO ENROLL AFTER PURCHASE OF VEHICLE. H A CUSTOMER WHO ALLOWS ALL PACKAGES OF THEIR BLUE LINK SUBSCRIPTION TO EXPIRE AND THEN WISHES TO RE-SUBSCRIBE TO BLUE LINK. H A CUSTOMER WHO DID NOT ENROLL IN BLUE LINK WITHIN THE FIRST 30 DAYS OF OWNERSHIP (AT WHICH TIME THE DEVICE BECOMES INACTIVE), BUT THEN DECIDES TO ENROLL. H A SUBSEQUENT OWNER WHO WISHES TO ENROLL IN BLUE LINK.
5NP-N4N2R-09
Service Bulletin/Repair Instructions
THE 2015 - 2016 SONATA (LF), 2016 SONATA HYBRID (LF HEV), AND 2017 ELANTRA (AD) FEATURES A TWO STAGE (PRIMARY AND SECONDARY) FRONTAL DRIVER AIRBAG. DUE TO A MANUFACTURING ERROR, THE SECOND STAGE FOR THE AIRBAG MAY NOT HAVE BEEN PROPERLY INSTALLED IN SOME VEHICLES. IN THE EVENT OF A COLLISION REQUIRING FRONTAL SECOND STAGE AIRBAG DEPLOYMENT, THE DRIVER'S SECOND STAGE AIRBAG WILL NOT DEPLOY, INCREASING THE RISK OF INJURY. THIS BULLETIN DESCRIBES THE PROCEDURE TO REPLACE THE DRIVER AIRBAG (DAB) TO CORRECT THIS CONDITION.
5NP-A8X7E-09
Service Bulletin/Repair Instructions
HYUNDAI MOTOR AMERICA IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE A/C SUCTION & LIQUID TUBE ASSEMBLY ON CERTAIN 2017 MODEL YEAR ELANTRA VEHICLES. SERVICE CAMPAIGN TEE PROVIDES A PROCEDURE TO REPLACE THE A/C SUCTION & LIQUID TUBE ASSEMBLY.
5NP-J4Z4M-09
Service Bulletin/Repair Instructions
HYUNDAI MOTOR AMERICA IS CONDUCTING A SERVICE CAMPAIGN TO VERIFY THE BATTERY TERMINAL AND BATTERY MOUNTING BRACKET TORQUE ON CERTAIN 2017 MODEL YEAR ELANTRA VEHICLES. SERVICE CAMPAIGN TAA PROVIDES A SERVICE PROCEDURE TO VERIFY THE TERMINAL AND BRACKET TORQUE.
5NP-N2L3T-09
Service Bulletin/Repair Instructions
THE BATTERY MOUNTING BRACKET WAS RECENTLY REPLACED ON SOME 2017MY ELANTRA VEHICLES AT A PORT FACILITY. THE BATTERY TERMINALS AND BATTERY MOUNTING BRACKET BOLTS MIGHT NOT HAVE BEEN PROPERLY SECURED DURING REPLACEMENT.
16-01-017
Service Bulletin/Repair Instructions
BATTERY TERMINAL AND MOUNTING BRACKET INSPECTION (SERVICE CAMPAIGN TAA) Description: The battery mounting bracket was recently replaced on some 2017MY Elantra vehicles at a port facility. The battery terminals and battery mounting bracket bolts might not have been properly secured during replacement. This bulletin provides the procedure to verify the battery terminal and battery mounting bracket torque.
16-AT-004
Service Bulletin/Repair Instructions
AUTOMATIC TRANSAXLE (6-SPEED) ATM FLUID LEVEL CHECK Description: The following vehicles are equipped with a 6-speed automatic transmission. The ATF level must be checked by the following procedure: NOTICE Use only ATF meeting the SP-IV specification approved by Hyundai. DO NOT use SP-III or other ATF which may result in degradation of shift quality or transaxle durability.
16-AT-003
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.