Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2524000012
High Voltage Air Conditioning Refrigerant Dye
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
9100624
Verify Reman part number availability. Order the "R" part number for all orders:
09-010-25
2.4L Excessive Oil Consumption XS1 Warranty Extension The customer may describe one or more of the following: ● Oil pressure low indicator lamp illumination between oil changes. ● Excessive oil consumption This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
U90 - Parts Ordering
U90 - Parts Ordering
09-018-24
2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ● Oil pressure low indicator lamp illumination between oil changes. ● Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
100096
U90 Parts Ordering
31-001-24
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
1000123
Air Bag Warning Lamp Illumination Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.
2310423
Front Side Window Contour Seal Deformation One or both front door side window seals are deformed Fig. 1. This bulletin involves replacing the window seal and glass.
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
S2325000007
MIL/check engine lamp comes on after performing U90 recall PCM software update.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
RecallU90
Emissions Recall U90 - Catalyst Efficiency
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0700723
Water Quality When Mixed With Engine Coolant
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
0900323
2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ? Oil pressure low indicator lamp illumination between oil changes. ? Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
3100123
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
09-003-23
2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: Oil pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
88806
Warranty Bulletin D-23-01 - (XB1) 2.4L Engine ? Select 2014 - 2019 Jeep Cherokee (KL), 2017 - 2018 Jeep Compass (MP), 2015 - 2018 Jeep Renegade (FWD/AWD) (BU), 2013 - 2016 Dodge Dart (PF), 2015 - 2017 Chrysler 200 (UF), 2016 - 2018 Fiat 500X (FWD) (FB), (AWD), 2015 - 2018 Ram Promaster City (VM)
31-002-22
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
09-013-22
2.4L Engine Oil Consumption Test The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine. This bulletin involves performing an oil consumption verification test.
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
CSNW20
Customer Satisfaction Notification W20 Reprogram Powertrain Control Module
W20
Powertrain Control Module.
23-042-15
The outside door handle cable grommet does not seal effectively for water
2304215
The outside door handle cable grommet does not seal effectively for water
W84
Customer Satisfaction Notification W84 Powertrain Software Update
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007RevC
Customer Complaint May Include Engine Oil Leak Or Consumption
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
18-042-21
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1D7F-00 - ETC Self-Learning Failure. P1523-00 - VVA Low Oil Pressure. P1524-00 - Oil Pressure Out Of Range - Camshaft Advance/Retard Disabled. P0141 - O2 Sensor 1/2 Heater Performance. Some customers may experience one or more of the following conditions: After a short trip and shutting the engine off for 5-10 minutes, vehicle exhibits a long crank/start condition(2016 BU EMEA only). Cruise control will not set at 32 kph (20 mph). Engine cranking times out after five seconds. Cruise control will not engage at highway speeds and when in 6th gear. A ticking noise coming from the top of the engine area. The ticking noise is heard particularly at idle (EMEA and APAC only). The following enhancements are also included: Improved purge sensor performance. Updated fuel strategy to inhibit spark plug fouling.
1804221
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1D7F-00 - ETC Self-Learning Failure. P1523-00 - VVA Low Oil Pressure. P1524-00 - Oil Pressure Out Of Range - Camshaft Advance/Retard Disabled. P0141 - O2 Sensor 1/2 Heater Performance. Some customers may experience one or more of the following conditions: After a short trip and shutting the engine off for 5-10 minutes, vehicle exhibits a long crank/start condition(2016 BU EMEA only). Cruise control will not set at 32 kph (20 mph). Engine cranking times out after five seconds. Cruise control will not engage at highway speeds and when in 6th gear. A ticking noise coming from the top of the engine area. The ticking noise is heard particularly at idle (EMEA and APAC only). The following enhancements are also included: Improved purge sensor performance. Updated fuel strategy to inhibit spark plug fouling.
08-064-21
Flash: Radio Frequency Hub Module (RFHM) Enhancements This bulletin involves reprogramming the RFHM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure (Software has been updated to better address this DTC). In addition, the customer may notice the following condition(s): Service Passive Entry Light" on cluster and MIL code B1053-64. Vehicle will not shut off with DTC B1053-64. Vehicle may not start with DTC B1053-64. With the ignition in the run position and the engine not running, the vehicle may not turn itself off after 30 minutes. Doors may not unlock when using the Remote Keyless Entry (RKE) Fob.(2015 only) Tire pressure monitoring (TPM) light may illuminate when using the winter tires in winter mode functionality.(2015-2016 only) After an engine start and the doors are closed, a message in the cluster may be displayed ?Key Not Detected? when the key is actually present.(2015-2016 only) Only a message is displayed, the vehicle will start.
0806421
Flash: Radio Frequency Hub Module (RFHM) Enhancements This bulletin involves reprogramming the RFHM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure (Software has been updated to better address this DTC). In addition, the customer may notice the following condition(s): Service Passive Entry Light" on cluster and MIL code B1053-64. Vehicle will not shut off with DTC B1053-64. Vehicle may not start with DTC B1053-64. With the ignition in the run position and the engine not running, the vehicle may not turn itself off after 30 minutes. Doors may not unlock when using the Remote Keyless Entry (RKE) Fob.(2015 only) Tire pressure monitoring (TPM) light may illuminate when using the winter tires in winter mode functionality.(2015-2016 only) After an engine start and the doors are closed, a message in the cluster may be displayed ?Key Not Detected? when the key is actually present.(2015-2016 only) Only a message is displayed, the vehicle will start.
W20 Combo Phase4
Customer Satisfaction Notification W20 Reprogram Powertrain Control Module
W84 Combo Phase3
Customer Satisfaction Notification W84 Powertrain Software Update
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S2008000113
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S2008000113 Rev.
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S1809000007 Rev.
Customer complaint may include engine oil leak/consumption.
08-027-21
Flash: Drivetrain Control Module (DTCM) Diagnostic and System Improvements This bulletin involves reprogramming the DTCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):C2502-64 - Signal Plausibility Failure. C2210-92 - ETM Hall Sensor Performance Or Incorrect Operation. C2220-54 - ETM Calibration Error Missing Calibration. C2020-01 - ECU Internal Fault - General Electrical Failure. This software update also includes the following enhancementsReduce Rear Drive Module (RDM) noise during disconnect phase at speeds above 45 kph (28 mph)North America Only.
0802721
Flash: Drivetrain Control Module (DTCM) Diagnostic and System Improvements This bulletin involves reprogramming the DTCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):C2502-64 - Signal Plausibility Failure. C2210-92 - ETM Hall Sensor Performance Or Incorrect Operation. C2220-54 - ETM Calibration Error Missing Calibration. C2020-01 - ECU Internal Fault - General Electrical Failure. This software update also includes the following enhancementsReduce Rear Drive Module (RDM) noise during disconnect phase at speeds above 45 kph (28 mph)North America Only.
W80 Combo Phase2
Customer Satisfaction Notification W80 Oil Consumption Inspection (Revision 2)
W80A
Customer Satisfaction Notification W80 Oil Consumption Inspection (Revision 2)
W80
Customer Satisfaction Notification W80 Oil Consumption Inspection (Revision 1)
S2108000027
CEL, Check Engine Lamp On, DTC P0339 Crankshaft Position Sensor Intermittent
W80 Combo Phase1
Customer Satisfaction Notification W80 Oil Consumption Inspection
S1908000028 Rev.
(Rev. A) Power Inverter Load Ratings
S1908000102
(Rev. A) Power Inverter Load Ratings
31-002-20
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
3100220
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S1823000026 Rev.
(Revision A) MySky Rough Operation Or Sticks Open
S1823000026RevA
(Revision A) MySky Rough Operation Or Sticks Open
S1508000374
Keys/Fobiks, Programming Keys With High Line BCM (L3 BCM)
S1508000380
Keys/Fobiks, Programming Keys With Base Vehicle BCM (L2 BCM)
09-006-20 REV. B
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
0900620
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
S2008000093
Blind Spot Or Park Assist Warnings, False Activation
S1721000016
Service 4wd Light On, Message AWD System Service Required
S2008000077
VP2R Radio Clock Not Keeping Time
09-006-20 REV. A
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
09-006-20
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
23-015-20
Disinfectant Solution Recommended for COVID-19
S1808000069
Intermittent Remote Start, Inhibit-Disable List
S1508000235
No Scan Tool Communication, Dominant Module Terminating Resistor Module Locations, BUS Circuit Terminal Testing Locations At The DLC (Diagnostic Link Connector) And BUS Test Values At DLC
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
18-030-20
Flash: Powertrain Diagnostic and System Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software.
08-030-20 REV. A
Flash: Body Control Module (BCM) Enhancements This bulletin involves reprogramming the BCM with the latest available software. The customer may describe the following:After starting the vehicle with remote start, the engine stops when the doors are unlocked.
09-004-20
No Weep Hole In Muffler Assembly This bulletin involves drilling a weep hole in the muffler assembly. The customer may describe a crank, no start condition, in freezing temperatures. This condition can be caused by condensation freezing in the muffler assembly.
08-027-20
2.4L Ignition Coil Boot Replacement This bulletin involves replacing all four ignition coil insulating boots. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
08-111-19 REV. A
RA3 and RA4 GPS Calibration Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)
9004172
ROTOR, Brake, Rear Counter bore hole on the original rotor is used during production to locate the rotor during assembly, it is not required for service. 2AMV8043A$ can be used for this application.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
08-111-19
RA3 and RA4 GPS Radio Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)
0811119
RA3 and RA4 GPS Radio Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)
18-089-19
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
1808919
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
V54 REV1
Revised Customer Satisfaction Notification V54 Engine Cooling Fan
08-089-19
Flash Over The Air (FOTA) Software Update RA3 and RA4 Radio This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
21-025-19
Nine-Speed Automatic Transmission (X80 Warranty Extension) This bulletin involves extending the warranty on the nine-speed automatic transmissions.
D-19-16
(X80) 9 Speed 948TE FWD/AWD or 9HP48 Automatic Transmissions - 2014-2015 Jeep Cherokee (KL) / 2015 Chrysler 200 (UF) / 2015 Jeep Renegade (BU) / 2015 Ram ProMaster (VM)
02-009-17
Creak/Rattle Noise Heard From Front Suspension This bulletin involves installing a protective sleeve in the front coil springs suspension. The customer may notice a creaking or rattle noise from the front of the vehicle while driving over bumps or rough roads.
08-110-17
Flash: Drivetrain Control Module (DTCM) Diagnostic and System Improvements This bulletin involves reprogramming the DTCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:C2502-64 - Signal Plausibility Failure. C2210-92 - ETM Hall Sensor Performance Or Incorrect Operation. C2220-54 - ETM Calibration Error Missing Calibration. C2020-01 - ECU Internal Fault - General Electrical Failure.
1808917
Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs have been set:P1523-00 - VVA Low Oil Pressure. P1524-00 - Oil Pressure Out Of Range - Camshaft Advance/Retard Disabled. P1D7F-00 - ETC Self-Learning Failure. P0141 - O2 Sensor 1/2 Heater Performance. Some customers may experience one or more of the following conditions:Cruise control will not set at 32 kph (20 mph). Engine cranking times out after five seconds. Cruise control will not engage at highway speeds and when in 6th gear. The following enhancements are also included:Improved purge sensor performance. Updated fuel strategy to inhibit spark plug fouling.
0810217
RA2 RJ2 RG2 RL2 and RM2 Radio Enhancements This bulletin involves updating the radio with the latest available software. The customer may notice one of the following:The parking sensor (warning chime) is still audible after the key is in the off position(EMEA and APAC Only). The radio re-boots if more than five favorite presets are set for each category (i.e. Sport or Rock)(RA2 Sales Code Only). Emergency number (i.e. 911) not set as default(U.S. BU Vehicles Only). Radio re-boots or displays black screens. When receiving or making outgoing phone calls, the other person may hear an echo or repeated phrases(16 MY FB Only). A false message displayed in the Instrument Panel Cluster (IPC) such as ?Parking Sensors Unavailable? and/or ?Sound System Unavailable?(16 MY FB Only).
1808817
Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. Customers may experience a ticking noise coming from the top of the engine area. The ticking noise is heard particularly at idle.
9003355
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.
21-042-17
Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following DTCs have been set:P0887 - TCM Power Control Circuit High. P061B - Internal Control Module Torque Calculation Performance. P072F - Stuck In Fourth Gear. P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance(2015 BU Only). P1CC9 - Unable to Engage Gear(2015 BU Only). P1D98 - Incorrect Gear Ratio Clutch B or D Defective(2015 BU Only). U0401 - Implausible Data Received From ECM-PCM(2015 BU Only). In addition, customers may notice the following condition(s):Harsh 1-2 upshift. Harsh garage shifts (Park to Reverse or Drive). CAN bus message may drop out after a network restart.
0808417
Flash: Radio Frequency Hub Module (RFHM) Enhancements This bulletin involves reprogramming the RFHM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTC has been set:B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure (Software has been updated to better addressthis DTC). In addition, the customer may notice the following condition(s):With the ignition in the run position and the engine not running, the vehicle may not turn itself off after 30 minutes. Doors may not unlock when using the Remote Keyless Entry (RKE) Fob. (2015 only) Tire pressure monitoring (TPM) light may illuminate when using the winter tires in winter mode functionality. (2015-2016 only) After an engine start and the doors are closed, a message in the cluster may be displayed ?Key Not Detected? when the key is actually present. (2015-2016 only) Only a message is displayed, the vehicle will start.
9003755
Cover Kit Please note that if you are attempting to get the cover kit and it is not available the gasket is available as a separate part number in the kit which is 04753095AB.
9003413
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003696
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
18-029-17
Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software.
9003694
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
03-001-17
Noise In Front Of Vehicle When Accelerating Or Decelerating This bulletin involves replacing both front half shafts. The customer may describe a ?clunk type? noise in front of the vehicle while accelerating or decelerating.
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
08-021-16 REV. B
Flash: BCM Diagnostic And System Improvements This bulletin involves reprogramming the Body Control Module (BCM) with the latest available software. The customer may describe one or more of the following: When ParkSense is turned off, the LED on the switch will turn on indicating the system is disabled. On the next key cycle the system is still disabled, but the LED on the switch will not turn on. Rear interior overhead lamps remain illuminated after exiting vehicle and locking from the driver's or passenger's door lock buttons. This is causing the vehicle battery to go dead. The door locks are inoperative when locking/unlocking remotely. False activation of the vehicle security alarm. False exterior light failure messages being displayed in the instrument cluster.
08-086-16
Flash: Engine Does Not Start at The First Attempt This bulletin involves upgrading the software in the Electronic Steering Lock (ESL) Module. The customer may experience malfunction on first attempt to start the vehicle. Initial cranking is inhibited but should start/crank on the second attempt. Upon further inspection the technician may find Diagnostic Trouble Code (DTC) B1000-01 - Electronic Control Unit - General Electrical Failure stored in the ESL Module.
08-078-16 REV. A
Flash: Park Assist Module (PAM) Enhancements This bulletin involves reprogramming the PAM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTC has been set: B1000-46 - Electronic Control Unit - Calibration/Parameter Memory Failure.In addition, the customer may notice one of the following conditions: The Instrument Panel Cluster (IPC) shows messages ?ParkSense not available" or "ParkSense disconnected". The park assist system may not be available at start up.
0810615
This bulletin involves reprogramming the Amplifier (AMP) with the latest available software.
21-035-16
Transmission Shift And Drivability Enhancements For P0901-00. This bulletin involves performing transmission harness replacement per S55 recall.Both the PCM and TCM must be up to date for these changes to be effective after the transmission harness repair. Customers may experience a Malfunction Indicator Lamp (MIL) illumination after S55 recall TCM flash has been performed. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0901-00 - Clutch 1 Actuator Control Circuit Range Performance.
2103216
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience the vehicle doesn?t pass back into drive mode when choosing to change gears using the paddle shifters. Even when holding the (+) paddle, while the gear lever is still in Drive, the vehicle remains locked in that mode.The following improvements are included in this update: Paddle shifter enhancements are included in this software update.
2302216
Creaks, Rattles, Squeaks Or Seal Gaps From My Sky Roof Panels This bulletin involves performing various repair procedures to the My Sky roof panels. Some customers may describe various noises coming from the My Sky roof panels, handle, or latch, as well as seal gaps between the panels.
2103116
Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the TCM memory: P061B - Internal Control Module Torque Calculation Performance. P072F - Stuck In Gear 4. P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance (2015 BU only). P0887 - TCM Power Control Circuit High (2015 BU only). P1CC9 - Unable to Engage Gear (2015 BU only). P1D98 - Incorrect Gear Ratio Clutch B or D Defective (2015 BU only). U0401 - Implausible Data Received From ECM-PCM (2015 BU only).In addition, customers may experience the following conditions: CAN Bus message may drop out after a network restart. Harsh 1-2 Upshift. Harsh Garage Shifts (Park to Reverse or Drive).
2401216
Water Leak On Right Front Floorboard This bulletin involves securing the condensation drain tube to the HVAC housing. Customers may experience a water leak on the right front floorboard inside the vehicle while using the climate controls or Heating Ventilation Air Conditioning (HVAC).
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
21-013-16 REV. B
948TE 9 Speed Transmission Quick Learn Procedure This bulletin provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic.
68256494A$
Windshield For Jeep Renegade (BU) windshields that exhibit imperfections such as stress cracking, inclusions/bubbles, scratches, or distortions, please contact: Chuck Hood at cell (248) 613-7591 If no response in 15 minutes, proceed with repair.
08-021-16 REV. A
Flash: BCM Diagnostic And System Improvements This bulletin involves reprogramming the Body Control Module (BCM) with the latest available software. The customer may describe one or more of the following: · **Rear interior overhead lamps remain illuminated after exiting vehicle and locking from the driver's or passenger's door lock buttons. This is causing the vehicle battery to go dead.** · The door locks are inoperative when locking/unlocking remotely. · False activation of the vehicle security alarm. · False exterior light failure messages being displayed in the instrument cluster.
0802116
Flash: BCM Diagnostic And System Improvements This bulletin involves reprogramming the Body Control Module (BCM) with the latest available software. The customer may describe one or more of the following: · **Rear interior overhead lamps remain illuminated after exiting vehicle and locking from the driver's or passenger's door lock buttons. This is causing the vehicle battery to go dead.** · The door locks are inoperative when locking/unlocking remotely. · False activation of the vehicle security alarm. · False exterior light failure messages being displayed in the instrument cluster.
18-063-16REV
Powertrain diagnostic and system improvements.
68321236A
RF Hub Module DTC, U1765-87 "RFHM (Radio Frequency Hub Module) - Missing Message" may appear in a stored state on a ignition power cycle. No troubleshooting or parts replacement is necessary if this code is stored as the system is functioning to design.
68321236A$
RF Hub Module DTC, U1765-87 "RFHM (Radio Frequency Hub Module) - Missing Message" may appear in a stored state on a ignition power cycle. No troubleshooting or parts replacement is necessary if this code is stored as the system is functioning to design.
05047457A
Multi-Air Actuator Assembly For 2.4 Tigershark Engine ONLY: When attempting to diagnose P Codes related to the MultiAir Unit, please note that there are multiple causes listed for each in the diagnostic procedure. This procedure must be followed to ensure the correct condition is being addressed. ~ Please verify the following (as listed in the first step in diagnostics) is not present before attempting repair:~ - Low Engine Oil - Incorrect oil filter that does not meet OEM specifications - Oil Dirty or Deteriorated (Lack of scheduled oil changes) - Incorrect Oil Viscosity/Weight - Engine Oil Contaminated (i.e. coolant and/or fuel) - Clogged Oil Galley Screen/Filter (top of block - feeds Multi-Air Unit) If there are any questions please contact: Seth Nankee at cell: (248) 303-5434 seth.nankee@fcagroup.com If no response within 15 minutes, please continue with diagnostics/repair.
23-022-16
Creaks, Rattles, Squeaks Or Seal Gaps From My Sky Roof Panels This bulletin involves performing various repair procedures to the My Sky roof panels. Some customers may describe various noises coming from the My Sky roof panels, handle, or latch, as well as seal gaps between the panels.
R73
Customer Satisfaction Notification R73 Wheel Stud Wrench The wheel stud wrench on about 11,700 of the above vehicles may break during use due to a non-compliant heat treatment process causing the material hardness to be out of specification. The wheel stud wrench must be replaced on the affected vehicles.
06106092A
Seat Relay For a Jeep Renegade or Fiat 500X ONLY, if the driver's power seat will not move in any axis and the key is in the on position with the door open: 1. Please take a Vehicle Scan Report, taking note of any active or stored DTC's, especially in the Body Control Module (BCM). 2. Before replacing the relay, call Rick Gordon at cell (248) 630-6281. If no answer leave a message and if after 15 minutes, there is no return call, proceed with the repair. 3. In the event there is no call-back, please email the Vehicle Scan Report to rick.gordon@fcagroup.com
06106092A$
Seat Relay For a Jeep Renegade or Fiat 500X ONLY, if the driver's power seat will not move in any axis and the key is in the on position with the door open: 1. Please take a Vehicle Scan Report, taking note of any active or stored DTC's, especially in the Body Control Module (BCM). 2. Before replacing the relay, call Rick Gordon at cell (248) 630-6281. If no answer leave a message and if after 15 minutes, there is no return call, proceed with the repair. 3. In the event there is no call-back, please email the Vehicle Scan Report to rick.gordon@fcagroup.com
08-065-16 REV. A
Flash: Amplifier Audio Enhancement This bulletin involves updating the amplifier (AMP) software. The customer may notice a poor audio quality. This condition may happen when the audio volume is at a mid to high output.
68141352A$
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.
08-033-16 REV. C
RA4 RG4 RJ4 Radio Enhancements This bulletin involves updating the radio software. Customers may experience one or more of the following: · **Uconnect Apps are missing (16 MY BU, RRT portion, US market only). · Unable to register Uconnect (16 MY BU, RRT portion, US market only). · Assist button on App is missing (16 MY BU, RRT portion, US market only).** · Character missing on the keyboard with Cyrillic alphabet (For EU Market only). · Time of arrival NAV settings not saved over key-cycle (For EU Market only). · Audio Off delayed when pressing On/Off button (For EU Market only). · Digital Audio Broadcast (DAB) button missing after system startup (For EU Market only). · Head unit turns on at USB disconnection (For EU Market only). · Poor quality of German translations. · Acoustic warning missing when approaching a speed camera (EMEA market only). · 3D view malfunctions. · Road signs not correctly viewed during navigation. · After ignition has been turned on the language switches automatically to Italian from previously selected language. · Forward Collision Warning With Mitigation (FCW+) turns off spontaneously, after the ignition has been turned on and FCW+ warning light is on.
08-033-16 REV. B
RA4 RG4 RJ4 RADIO ENHANCEMENTS THIS BULLETIN INVOLVES UPDATING THE RADIO SOFTWARE. CUSTOMERS MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING: · **CHARACTER MISSING ON THE KEYBOARD WITH CYRILLIC ALPHABET (FOR EU MARKET ONLY). · TIME OF ARRIVAL NAV SETTINGS NOT SAVED OVER KEY-CYCLE (FOR EU MARKET ONLY). · AUDIO OFF DELAYED WHEN PRESSING ON/OFF BUTTON (FOR EU MARKET ONLY). · DIGITAL AUDIO BROADCAST (DAB) BUTTON MISSING AFTER SYSTEM STARTUP (FOR EU MARKET ONLY). · HEAD UNIT TURNS ON AT USB DISCONNECTION (FOR EU MARKET ONLY).** · POOR QUALITY OF GERMAN TRANSLATIONS. · ACOUSTIC WARNING MISSING WHEN APPROACHING A SPEED CAMERA (EMEA MARKET ONLY). · 3D VIEW MALFUNCTIONS. · ROAD SIGNS NOT CORRECTLY VIEWED DURING NAVIGATION. · AFTER IGNITION HAS BEEN TURNED ON THE LANGUAGE SWITCHES AUTOMATICALLY TO ITALIAN FROM PREVIOUSLY SELECTED LANGUAGE. · FORWARD COLLISION WARNING WITH MITIGATION (FCW+) TURNS OFF SPONTANEOUSLY, AFTER THE IGNITION HAS BEEN TURNED ON AND FCW+ WARNING LIGHT IS ON.
68105583A$
PENTASTAR OIL FILTER ADAPTER BEFORE REPLACING THIS PART, PLEASE CALL ANY ONE OF THE FOLLOWING PEOPLE. ENGINEERING IS SEEKING INFORMATION REGARDING THIS PART.~ DYE MUST BE USED TO DETERMINE WHERE THE LEAK IS COMING FROM BEFORE REPLACING. ALSO PLEASE CHECK THE RECENTLY UPDATED SERVICE BULLETIN NUMBER 09-008-15. ~ FIRST: NICK MORAND CELL (248) 410-5078 - NICK.MORAND@FCAGROUP.COM SECOND: BOB JACKSON CELL (248) 944-0466 - BOB.JACKSON@FCAGROUP.COM THIRD: JOE LOVELL CELL (734 309-6467 - JOE.LOVELL@FCAGROUP.COM IF A RESPONSE IS NOT RECEIVED WITHIN 15 MINS, THEN PROCEED WITH THE NECESSARY REPAIR.
68312314A
BCM - Body Computer For MY15 and MY16 BU vehicles in NAFTA only~ Power Seats INOP & DTC B1062-11 ELECTRIC SEAT-CIRCUIT SHORT TO GROUND. Issue still present after all troubleshooting instructions were followed ~ Prior to replacing the BCM, check if relays in the PDC are seated properly, but DO NOT replace relays as no issues were found with the relays in the past.~ Take vehicle scan and bus log with the vehicle in RUN and email to Andrew Kravets: andrew.kravets@fcagroup.com before replacing the BCM. ~ Please include a description of the actions taken during troubleshooting.~
68312314A$
BCM - Body Computer For MY15 and MY16 BU vehicles in NAFTA only~ Power Seats INOP & DTC B1062-11 ELECTRIC SEAT-CIRCUIT SHORT TO GROUND. Issue still present after all troubleshooting instructions were followed ~ Prior to replacing the BCM, check if relays in the PDC are seated properly, but DO NOT replace relays as no issues were found with the relays in the past.~ Take vehicle scan and bus log with the vehicle in RUN and email to Andrew Kravets: andrew.kravets@fcagroup.com before replacing the BCM. ~ Please include a description of the actions taken during troubleshooting.~
14-003-16 REV. A
Replace Fuel Pump This bulletin involves replacing the fuel pump module. Some vehicles may have been built with a fuel pump that can cause a no start condition on vehicles with low mileage (Usually less than 100 miles).
1400316REVA
Replace Fuel Pump This bulletin involves replacing the fuel pump module. Some vehicles may have been built with a fuel pump that can cause a no start condition on vehicles with low mileage (Usually less than 100 miles).
18-063-16
Flash: 2.4L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Engine Control Module (ECM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) stored in the ECM memory: · **P050D - Cold Start Rough Idle. · P0101 - Mass Air Flow Sensor "A" Circuit Performance. · P0335 - Crankshaft Position Sensor Circuit. · P1CEC - Variable Valve Solenoid Valve Cold Start Closing Position 1 Timing Over-Retard. · P1CED - Variable Valve Timing Solenoid Valve Cold Start Closing Position Timing Over-Advance. · P1607 - PCM Internal Shutdown Timer Rationality. · P0128 - Thermostat Rationality. · P2610 - PCM Internal Engine Off Timer Performance. · P0440 - General EVAP System Failure. · P0441 - EVAP Purge System Performance. · P0456 - EVAP System Small Leak. · P0455 - EVAP System Large Leak. · P0452 - EVAP Pressure Switch Stuck Closed. · P0133 - O2 Sensor 1/1 Slow Response. · C0501 - Wheel Speed Signal Left Front Rationality. · C0507 - Wheel Speed Signal Right Front Rationality. · C050D - Wheel Speed Signal Left Rear Rationality. · C0513 - Wheel Speed Signal Right Rear Rationality. · U0428-00 - Implausible Data Received From Steering Angle Sensor Module. · C0061 - Lateral Acceleration Sensor.** · U0402 - Implausible Data Received From TCM. · P0133 - O2 Sensor 1/1 Slow Response. · P050D - Cold Start Rough Idle. In addition, customers may experience one or more of the following concerns: · RPM flare at cold start. · Less than desired idle performance. · Cold engine RPM surge with gear engagement.
1806316
Flash: 2.4L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Engine Control Module (ECM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) stored in the ECM memory: · **P050D - Cold Start Rough Idle. · P0101 - Mass Air Flow Sensor "A" Circuit Performance. · P0335 - Crankshaft Position Sensor Circuit. · P1CEC - Variable Valve Solenoid Valve Cold Start Closing Position 1 Timing Over-Retard. · P1CED - Variable Valve Timing Solenoid Valve Cold Start Closing Position Timing Over-Advance. · P1607 - PCM Internal Shutdown Timer Rationality. · P0128 - Thermostat Rationality. · P2610 - PCM Internal Engine Off Timer Performance. · P0440 - General EVAP System Failure. · P0441 - EVAP Purge System Performance. · P0456 - EVAP System Small Leak. · P0455 - EVAP System Large Leak. · P0452 - EVAP Pressure Switch Stuck Closed. · P0133 - O2 Sensor 1/1 Slow Response. · C0501 - Wheel Speed Signal Left Front Rationality. · C0507 - Wheel Speed Signal Right Front Rationality. · C050D - Wheel Speed Signal Left Rear Rationality. · C0513 - Wheel Speed Signal Right Rear Rationality. · U0428-00 - Implausible Data Received From Steering Angle Sensor Module. · C0061 - Lateral Acceleration Sensor.** · U0402 - Implausible Data Received From TCM. · P0133 - O2 Sensor 1/1 Slow Response. · P050D - Cold Start Rough Idle. In addition, customers may experience one or more of the following concerns: · RPM flare at cold start. · Less than desired idle performance. · Cold engine RPM surge with gear engagement.
21-021-16
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · **P061B-00 - Internal Control Module Torque Calculation Performance. · P072F-00 - Stuck In Gear 4.** · P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. · P1DAD - Input Shaft-Output Shaft Direction Correlation. · P1CC9 - Unable to Engage Gear. · P1D98 - Incorrect Gear Ratio Clutch B or D Defective. · U1424 - Implausible Engine Torque Signal Received. In addition to correcting the DTCs listed this software update includes the following enhancements: · **Coast down bump on 7-6, 6-5, 5-4, 5-3 downshift improvements. · Cold 1-2, 2-3 upshift improvements. · 1-2, 2-3 upshift flare control improvements. · Power-on upshift improvements. · Lift foot upshift 2-3, 4-5, 8-9 improvements.** · Garage shift improvements (Shifting from Park or Neutral to Drive or Reverse). · 1-2 Shift Quality improvements. · Improved engine performance under certain operating conditions (High Altitude, High Ambient Temperatures and High Humidity). · Hill shift pattern optimization. · Improved redline shift performance. · Improved upshifts, downshifts, coast down shifts and tip shifts.
2102116
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · **P061B-00 - Internal Control Module Torque Calculation Performance. · P072F-00 - Stuck In Gear 4.** · P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. · P1DAD - Input Shaft-Output Shaft Direction Correlation. · P1CC9 - Unable to Engage Gear. · P1D98 - Incorrect Gear Ratio Clutch B or D Defective. · U1424 - Implausible Engine Torque Signal Received. In addition to correcting the DTCs listed this software update includes the following enhancements: · **Coast down bump on 7-6, 6-5, 5-4, 5-3 downshift improvements. · Cold 1-2, 2-3 upshift improvements. · 1-2, 2-3 upshift flare control improvements. · Power-on upshift improvements. · Lift foot upshift 2-3, 4-5, 8-9 improvements.** · Garage shift improvements (Shifting from Park or Neutral to Drive or Reverse). · 1-2 Shift Quality improvements. · Improved engine performance under certain operating conditions (High Altitude, High Ambient Temperatures and High Humidity). · Hill shift pattern optimization. · Improved redline shift performance. · Improved upshifts, downshifts, coast down shifts and tip shifts.
08-065-16
Flash: Amplifier Audio Enhancement This bulletin involves updating the amplifier (AMP) software. The customer may notice a poor audio quality. This condition may happen when the audio volume is at a mid to high output.
68105583A
Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
RL305553A
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
14-003-16
Replace Fuel Pump This bulletin involves replacing the fuel pump module. Some vehicles may have been built with a fuel pump that can cause a no start condition on vehicles with low mileage (Usually less than 100 miles).
1400316
Replace Fuel Pump This bulletin involves replacing the fuel pump module. Some vehicles may have been built with a fuel pump that can cause a no start condition on vehicles with low mileage (Usually less than 100 miles).
08-033-16A
Updating the radio software.
0803316A
Updating the radio software.
68141352A
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
08-061-16
Wire repairs to engine harness.
0806116
Wire repairs to engine harness.
22-002-16
Rust On Wheel Lug Studs This bulletin involves replacing the wheel lug studs with the newer capped studs. The customer may describe the lug studs are rusting.
2200216
Rust On Wheel Lug Studs This bulletin involves replacing the wheel lug studs with the newer capped studs. The customer may describe the lug studs are rusting.
Z5091195A
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Z5091195A$
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
08-014-16
Flash: Improvements To Messages Displayed In The Cluster This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest available software. This IPC software update will contain the following changes within the Electronic Vehicle Information Center (EVIC): · **Improvements to cruise control to correct an issue while pressing the accelerator pedal the message override is shown and sometimes flickers on the IPC display. · One chime indication when speed is overpassed instead of a continous chime and message. · ?Push brake pedal" message added when attempting to shift out of Neutral (N). · Service interval correction.** · Correct the condition; the remote door lock configuration is not available within customer programmable features (APAC market only). · Correct the condition; intermittently pushing the RKE (Remote Keyless Entry) button on the transponder key one time, only the driver?s door is unlocked. All doors are expected to open by default (APAC market only). · Added message ?Release brake pedal before switch off" at key removal, when the gear shift lever is in the park position and the brake pedal is pressed. · Changed message from ?Unavailable Wipe Front Radar Sensor? to ?Front Radar Sensor Temporarily Blocked.?
08-014-16 REV A
SUBJECT: Flash: Improvements To Messages Displayed In The Cluster OVERVIEW: This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest available software.
08-014-16 REV. A
Flash: Improvements To Messages Displayed In The Cluster This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest available software. This IPC software update will contain the following changes within the Electronic Vehicle Information Center (EVIC): · **Improvements to cruise control to correct an issue while pressing the accelerator pedal the message override is shown and sometimes flickers on the IPC display. · One chime indication when speed is overpassed instead of a continous chime and message. · ?Push brake pedal" message added when attempting to shift out of Neutral (N). · Service interval correction.** · Correct the condition; the remote door lock configuration is not available within customer programmable features (APAC market only). · Correct the condition; intermittently pushing the RKE (Remote Keyless Entry) button on the transponder key one time, only the driver?s door is unlocked. All doors are expected to open by default (APAC market only). · Added message ?Release brake pedal before switch off" at key removal, when the gear shift lever is in the park position and the brake pedal is pressed. · Changed message from ?Unavailable Wipe Front Radar Sensor? to ?Front Radar Sensor Temporarily Blocked.?
68277402A
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
08-034-16 REV. A
RL4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: · ParkSense audio delay. · Forward Collision Warning (FCW) turns off spontaneously after key on and FCW warning light is on.
0803416 REV A
This bulletin involves inspecting and, if required, updating the radio software.
0803416REVA
This bulletin involves inspecting and, if required, updating the radio software.
08-033-16
RA4 RG4 Radio Enhancements This bulletin involves updating the radios software. Customers may experience one or more of the following: · Poor quality of German translations. · Acoustic warning missing when approaching a speed camera. (EMEA market only) · 3D view malfunctions. · Road signs not correctly viewed during navigation. · After ignition has been turned on the language switches automatically to Italian from previously selected language. · Forward Collision Warning with mitigation (FCW+) turns off spontaneously
08-034-16
RL4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: · ParkSense audio delay. · Forward Collision Warning (FCW) turns off spontaneously after key on and FCW warning light is on.
0803316
This bulletin involves updating the radios software.
0803416
This bulletin involves inspecting and, if required, updating the radio software.
21-013-16
948TE 9 Speed Transmission Quick Learn Procedure This bulletin provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic.
21-013-16 REV A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
21-013-16 REV. A
948TE 9 Speed Transmission Quick Learn Procedure This bulletin provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic.
2101316 REV A
Speed Transmission Quick Learn Procedure.
2101316REVA
Speed Transmission Quick Learn Procedure.
2101316
Speed Transmission Quick Learn Procedure.
05-001-16 REV. A
Flash: ABS Module Electronic Parking Brake Enhancements This bulletin involves updating the Anti-lock Brake System (ABS) module software. The customer may describe: · The key may get stuck in the ignition key cylinder. · The Electronic Parking Brake (EPB) does not engage with the ?Auto Apply? feature selected. NOTE: The Parking Brake will apply when the switch is manually activated.
0500116 REV A
: ABS Module Electronic Parking Brake Enhancements.
0500116REVA
: ABS Module Electronic Parking Brake Enhancements.
31-001-16
Do Not Apply Corrosion Protection On Sheet Molding Compound (SMC) Plastic Panels This bulletin involves discussing SMC plastic panels and applying corrosion protection.
18-013-16 REV A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
1801316REVA
Diagnostic And System Improvements.
23-008-16
Some customers may describe a squeak noise coming from rear cargo area. Noise is most noticeable while driving over rough roads and during vehicle turns.
2300816
Some customers may describe a squeak noise coming from rear cargo area. Noise is most noticeable while driving over rough roads and during vehicle turns.
0801416
This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest
08-012-16
Flash: Adaptive Cruise Control Enhancements This bulletin involves reprogramming the Adaptive Cruise Control (ACC) module with the latest available software. NAFTA only: The customer may experience an issue with the Forward Collision Warning system. The audible warning does not function when the vehicle speed is below 30 KMH (18.6 MPH) when ?only warning? option is selected by the customer. EMEA only: The customer may experience an erroneous message; ?Radar to be Cleaned? displayed in the cluster.
0801216
This bulletin involves reprogramming the Adaptive Cruise Control (ACC) module with the
08-009-16
Radio Software Enhancements This bulletin involves updating the radio's software. A customer may experience one or more of the following: · Radio display screen intermittently may go blank. · Radio display screen may lock up. · Back up display may not turn off. · Loss of radio memory for skipped channels or incorrectly displaying skipped channels in the menu list. · Korean language was not supported (APAC - Korea only). Additional Enhancements: · Removed the charging schedule from showing in the setting menu (FF BEV only). · Adding Korean language support (APAC - Korea only).
RL108213A$
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
09-003-16
Turbocharger Replacement This bulletin involves replacing the turbocharger and repositioning the control solenoid valve air intake filter. The customer may describe a drop in vehicle performance and/or a malfunction indicator light (MIL) illuminated. The following Diagnostic Trouble Codes (DTCs) will also be stored or active: · P2564 - 00 - Variable Geometry Turbocharger Position Sensor Deviation Signal Amplitude Less Than Minimum. · P2565 - 00 - Variable Geometry Turbocharger Position Sensor Deviation Signal Amplitude Greater Than Maximum.
05-001-16
Flash: ABS Module Electronic Parking Brake Enhancements This bulletin involves updating the Anti-lock Brake System (ABS) module software. The customer may describe: · **The key may get stuck in the ignition key cylinder.** · The Electronic Parking Brake (EPB) does not engage with the ?Auto Apply? feature selected.
0500116
: ABS Module Electronic Parking Brake Enhancements.
08-002-16
Malfunction Indicator Lamp (MIL) Illumination Diagnostic Trouble Code (DTC) P0113 The wiring at the connector of the Intake Air Temperature (IAT) sensor may be compromised due to wire strain causing DTCs. This bulletin involves adding a jumper harness on the IAT sensor to reduce this strain. Some customers may experience a MIL illumination. Upon further inspection, the technician may find P0113 Intake Air Temperature Sensor 1 Circuit High. Installing the jumper harness will help prevent IAT issues from occurring.
24-002-16
Air Conditioning Inoperative This bulletin involves replacing the Manual Climate Control Module. A small number of customers may experience the loss of air conditioning operation (A/C compressor will not turn on).
05-012-15
Flash: ABS Module Electronic Parking Brake Enhancements. This bulletin involves updating the Anti-Lock Brake System (ABS) module software. The customer may describe the Electronic Parking Brake (EPB) does not engage with the ?Auto Apply? feature selected. NOTE: The Parking Brake will apply when the switch is manually activated.
0501215
ABS Module Electronic Parking Brake Enhancements.
08-127-15
Flash: Radio Frequency Hub Module (RFHM) Enhancement This bulletin involves updating the RFHM software. A customer may experience one or both of the following conditions: ? Passive entry light on with Diagnostic Trouble Code (DTC) B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure. ? After the engine starts and the door is closed, a message in the cluster is being displayed ?Key Not Detected? when the key is actually present. NOTE: Only a message is displayed and the vehicle will start. After the engine starts the message goes away.
53034160A
Part Description: Accelerator Pedal Issue Description: Vehicle has accelerator pedal fault code. Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
05-010-15 REV A
Front Brake Squeak/Squeal Noise This bulletin involves cleaning excessive sealant from the front brake caliper adaptor brackets and replacing the adaptor bracket mounting bolts and/or replacing the front brake pads and related hardware. The customer may describe one or more of the front brake squeak/squeal noise symptoms/conditions: - Squeak/squeal noise during moderate brake apply combined with light steering. The noise typically occurs with warm brakes after several brake applications. - Squeak/squeal noise during low speed brake apply with vehicle moving forward or reverse. The noise typically only occurs after the vehicle sits overnight in colder ambient temperatures and the noise will go away after a few brake applications.
24-007-15
Air Conditioning Inoperative This bulletin involves replacing the Manual Climate Control Module. A small number of customers may experience the loss of air conditioning operation (AC will not turn on).
08-109-15
Cannot Complete Restore Vehicle Configuration Or Proxi Alignment This bulletin involves inspecting and replacing the Comfort Seat and Wheel Module (CSWM), if required. The dealer may not be able to complete a Restore Vehicle Configuration and/or Proxi Alignment. Certain CSWM may have incompatible software that will prevent this routine from being completed.
0810915
This bulletin involves inspecting and replacing the Comfort Seat and Wheel Module
18-083-15
Flash: 1.6L and 2.0L Diagnostic And System Enhancements This bulletin involves upgrading the software in the Engine Control Module (ECM). A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the ECM memory. ? P112C-00 Lambda Sensor Downstream Signal Plausibility Check. ? P1451-00 Diesel Particulate Filter Efficiency Result.
1808315
This bulletin involves upgrading the software in the Engine Control Module (ECM).
08-106-15
Flash: Enable Audio Response When Making 911 And Assist Calls This bulletin involves reprogramming the Amplifier (AMP) with the latest available software. Updating the software in the amp will correct a condition when using the vehicle's 911/Assist Call feature. The first response operator can hear the vehicle occupant, but the vehicle occupant cannot hear the first response operator.
08-066-15 REVA
Flash: Improvements To Messages Displayed In The Cluster This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest available software. This IPC software update will contain the following changes within the Electronic Vehicle Information Center (EVIC): ? Added message ?Release brake pedal before switch off" at key removal, when the gear shift lever is in the park position and the brake pedal is pressed. ? Changed message from Unavailable Wipe Front Radar Sensor? to ?Front Radar Sensor Temporarily Blocked.?
0806615 REV A
This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest
0806615REVA
This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest
21-038-15 REV-B
Flash: Drivetrain Control Module (DTCM) C2020-01 ECU Internal Fault setting in the DTCM This bulletin involves reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.
21-038-15 REV. B
Flash: Drivetrain Control Module (DTCM) C2020-01 ECU Internal Fault setting in the DTCM This bulletin involves reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.
08-094-15
Flash: Park Assist Module (PAM) Enhancements This bulletin involves reprogramming the Park Assist Module (PAM) with the latest available software. A customer may notice the park assist system may not be available at start up.
SB-08-094-15
2015 JEEP RENEGADE: PARK ASSIST MODULE NEEDS REPROGRAMMING WITH THE LATEST SOFTWARE AVAILABLE DUE TO A NON START UP *CN
21-054-15
Flash: Vehicle Will Not Shift Out Of Park This bulletin involves reprogramming the Electronic Shift Module (ESM) with the latest available software. Some Customers may experience a condition where the vehicle will not shift out of park while the engine running at idle and brake pedal applied. Cycling the ignition key off and restarting the engine will allow shift. Technicians may find DTC P0606-00 Control Module Processor. Flashing the ESM with the latest software will correct this concern.
07-007-15
Vibration Felt In Steering Wheel This bulletin involves applying aluminium adhesive tape around the radiator anchoring pin. The customer may describe a vibration that is felt in the steering wheel. A vibration may be caused by clearance between the radiator anchoring pin and radiator support rubber bushing.
SB-07-007-15
JEEP RENEGADE: THERE IS VIBRATION IN THE STEERING WHEEL WHICH MAY BE CAUSED BY CLEARANCE BETWEEN RADIATOR ANCHORING PIN AND RADIATOR SUPPORT RUBBER BUSHING *CN
21-038-15 REV-A
Flash: Drivetrain Control Module (DTCM) C2020-01 ECU Internal Fault setting in the DTCM This bulletin involves reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.
21-038-15 REV. A
Flash: Drivetrain Control Module (DTCM) C2020-01 ECU Internal Fault setting in the DTCM This bulletin involves reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.
21-048-15 REV-A
Flash: Drivetrain Control Module C2020-01 ECU Internal Fault setting in the DTCM This bulletin involves reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.
21-048-15 REV. A
Flash: Drivetrain Control Module C2020-01 ECU Internal Fault setting in the DTCM This bulletin involves reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.
SB21-038-15
JEEP RENEGADE: ALL WHEEL DRIVE LIGHT (AWD) IS ILLUMINATING DUE TO ERRONEOUSLY ECU INTERNAL FAULT SETTING AND PROCEDURE FOR REPROGRAMMING DRIVETRAIN CONTROL MODULE WITH NEWEST SOFTWARE *CN UPDATED 12/03/15 *CN
SB21-048-15REVA
2015 JEEP RENEGADE; 2016 FIAT 500X: ALL WHEEL DRIVE LIGHT ILLUMINATING DUE TO DTC MAY BE EXPERIENCED BY SOME CUSTOMERS. PROCEDURE ON REPROGRAMMING THE DRIVETRAIN CONTROL MODULE WITH LATEST SOFTWARE *CN UPDATED 9/3/15.
21-053-15
948TE 9 Speed Transmission Quick Learn Procedure This bulletin provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic.
SB21-053-15
2015 JEEP CHEROKEE; CHRYSLER 200; JEEP RENEGADE; RAM PROMASTER CITY; 2016 FIAT 500X: ERRATIC TRANSMISSION SHIFT QUALITY MAY BE INDICATED *CN
05-010-15
Front Brake Squeak/Squeal Noise This bulletin involves cleaning excessive sealant from the front brake caliper adaptor brackets and replacing the adaptor bracket mounting bolts and/or replacing the front brake pads and related hardware. The customer may describe one or more of the front brake squeak/squeal noise symptoms/conditions: ? Squeak/squeal noise during moderate brake apply combined with light steering. The noise typically occurs with warm brakes after several brake applications. ? Squeak/squeal noise during low speed brake apply with vehicle moving forward or reverse. The noise typically only occurs after the vehicle sits overnight in colder ambient temperatures and the noise will go away after a few brake applications.
08-062-15 REV-C
RA2, RG2 Radio Software Enhancements This bulletin involves updating the radio software. The customer may notice that blue tooth communication with the passenger is poor. If a passenger is trying to talk on the blue tooth phone, the caller will have a hard time understanding what the passenger is saying. The caller will not have any difficulty understanding the person in the driver?s seat. Additionally a false message may be displayed in the Cluster; Parking Sensors Unavailable and/or Sound System Unavailable. Fig. 1 Message Displayed In The Cluster Sound System Unavailable NOTE: If the above Icon/Message is displayed in the cluster, do NOT replace the speakers. Make sure the radio software is up to date.
08-062-15 REV-B
RA2, RG2 Radio Software Enhancements This bulletin involves updating the radio's software. The customer may notice that blue tooth communication with the passenger is poor. If a passenger is trying to talk on the blue tooth phone, the caller will have a hard time understanding what the passenger is saying. The caller will not have any difficulty understanding the person in the driver?s seat. Additionally a false message may be displayed in the Cluster; Parking Sensors Unavailable and/or Sound System Unavailable.
SB-08-062-15REVB
JEEP RENEGADE: PASSENGER MAY BE EXPERIENCING POOR BLUE TOOTH COMMUNICATION. MAY REQUIRE RADIO SOFTWARE UPDATING *CN
08-084-15
Electronic Power Steering System (EPS) Instrument Cluster Lamp ON This bulletin involves reprogramming the Electric Power Steering (EPS) module with the latest available software to correct an erroneous EPS lamp illumination. The customer may describe the Power Steering System Warning lamp (1) is illuminated on the instrument cluster (Fig. 1). Upon further inspection, the technician may find the following Diagnostic Trouble Code (DTC): C1214-87 Conf Data Code Request Message - Missing Message error set in the EPS control unit. Fig. 1 Instrument Cluster 1 - Power Steering System Warning lamp
SB-08-084-15
JEEP RENEGADE: POWER STEERING SYSTEM WARNING LAMP WILL ILLUMINATE ON INSTRUMENT CLUSTER. ELECTRIC POWER STEERING MODULE NEEDS REPROGRAMMING WITH LATEST SOFTWARE *CN
08-077-15 REV-A
RA4 RG4 RJ4 Radio Enhancement This bulletin involves updating the radios software. The customer may experience one or more of the following: ? Travel Link soft key missing (U.S. only). ? Assist/911 may be disconnected after accessory timer, times out (U.S. only). ? Weather map now available for SXM (U.S. only). ? Cannot select different map displays. ? Point Of Interest (POI) cannot be added as waypoints. ? Conference calls may not display all active callers. ? Improve iPod response time, to start playing audio. ? Browsing knob inoperative after exiting Short Message Service (SMS). ? ?Where Am I? feature inoperative while driving. ? When using iPod touch, the incorrect song name may be displayed. ? May not display Auto Park Brake menu, if equipped. ? Cannot create a new SMS, using phone numbers. ? Display the correct message, when in service mode. ? Personal setting lost after key cycle, dynamic guidelines and Show Time bar. ? False error message while in service brake mode. ? Poor or no audio from the radio, also radio controls may not respond. On further inspection the technician my find DTC B223B-00 Vehicle Configuration Mismatch. ? The option to enable/disable the Auto Park Brake is missing in the radio. This symptom is for Trailhawk vehicles in the (Canadian market only). IMPROVEMENTS ? Display Travel Link soft key on more of the display screens (U.S. only). ? Improve WiFi functionality (U.S. only). ? Display the correct media screen when using iPod touch. ? Improve screen layouts during media playback. ? Improved SMS screen displays. ? Correctly display speed lockout messages. ? Color improvements on navigation map. ? Improved chime warning volumes. ? Browsing improvements for Bluetooth audio. ? Improved conference call handling. ? Improved Voice Recognition (VR) commands for AM radio request.
08-062-15 REV-A
RA2, RG2 Radio Software Enhancements This bulletin involves updating the radio's software. The customer may notice that blue tooth communication with the passenger is poor. If a passenger is trying to talk on the blue tooth phone, the caller will have a hard time understanding what the passenger is saying. The caller will not have any difficulty understanding the person in the driver?s seat. Additionally a false message may be displayed on the radio; Audio & Parking Sensors Not Available.
21-030-15 REV-A
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. In addition to correcting the DTCs listed below this software update includes the following enhancements. ? Garage Shift Improvements (Shifting from Park or Neutral to Drive or Reverse). ? 1-2 Shift Quality Improvements. ? Improved Engine Performance under certain operating conditions (High Altitude, High Ambient Temperatures and High Humidity). ? Hill Shift Pattern Optimization. ? Improved Redline Shift Performance. ? Improved Upshifts, Downshifts, Coast Down Shifts and Tip Shifts. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or both of the following Diagnostic Trouble Codes (DTCs). ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. ? P1DAD - Input Shaft-Output Shaft Direction Correlation. ? P1CC9 - Unable to Engage Gear. ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective. ? U1424 - Implausible Engine Torque Signal Received.
SB21-030-15-REVA
2015 JEEP RENEGADE: SOME CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP ILLUMINATION. ALSO INVOLVES PROCEDURE FOR REPROGRAMMING TRANSMISSION CONTROL MODULE *CN
18-060-15
Flash: 1.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find a Diagnostic Trouble Code (DTC) has been set in the PCM. P0141 - O2 Sensor 1/2 Heater Performance.
24-003-15 REV-A
Air Conditioning Inoperative This bulletin involves reprogramming the Heating Ventilation Air Conditioning (HVAC) module with the latest available software. A small number of customers may experience the loss of air conditioning operation.
SB18-060-15
2015 JEEP RENEGADE: CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP ILLUMINATION. PROCEDURE FOR SELECTIVELY ERASING AND REPROGRAMMING POWERTRAIN CONTROL MODULE WITH LATEST SOFTWARE *CN
24-004-15
Air Conditioning Performance This bulletin involves reprogramming the Air Conditioning Module (ACM) with the latest available software. A small number of customers may experience poor air conditioning performance when the interior temperatures of the vehicle are above 60°C (140°F).
23-030-15
Door Noises And/Or Door Functions Inoperative This bulletin involves inspecting all mechanical and electrical functions of all doors. The customer may describe noises coming from one or more of the doors and/or loss of functionality to one or more of the door handles, locks, windows, lamps, and mirrors.
SB-23-030-15
JEEP: VEHICLE EXPERIENCING A LACK OF FUNCTIONALITY USAGE WITH REGARDING TO MIRRORS, LAMPS, LOCKS, WINDOWS, DOOR HANDLES AND NOISES COMING FROM DOORS. MODEL 2015 RENEGADE. *PE
08-078-15
Antenna Mast Will Not Screw Into Base This bulletin involves inspecting and installing the correct antenna mast, if required. The dealer may not be able to install the antenna mast to the antenna base. The mast may have the incorrect thread pitch (1.0 mm) and will not screw into the base. The mast should have a thread pitch of 0.8 mm.
08-077-15
RA4 RG4 RJ4 Radio Enhancement This bulletin involves updating the radios software. The customer may experience, poor or no audio from the radio, also radio controls may not respond. On further inspection the technician may find DTC B223B-00 Vehicle Configuration Mismatch. The option to enable/disable the Auto Park Brake is missing in the radio. This symptom is for Trailhawk vehicles in the Canadian market.
05-007-15
Front Brake Squeak/Squeal Noise This bulletin involves cleaning excessive sealant from the front brake caliper adaptor brackets and replacing the adaptor bracket mounting bolts. The customer may describe a front brake squeak/squeal noise during moderate brake apply combined with light steering. The noise typically occurs with warm brakes after several brake applications.
08-073-15
Flash: False Vehicle Security Alarm Activation During Surveillance Mode This bulletin involves reprogramming the Body Computer Module (BCM) with the latest available software. The customer may describe a false activation of the Vehicle Security Alarm.
08-071-15
Flash: BCM Update To Correct Various Symptoms This bulletin involves updating the Body Control Module (BCM) software. The customer may describe one or more of the following: ? The door locks are inoperative when locking/unlocking remotely. ? False activation of the Vehicle Security Alarm. ? False exterior light failure messages being displayed in the Instrument Cluster.
SB08-071-15
JEEP: 2015 RENEGADE SOFTWARE UPDATE ON BODY CONTROL MODULE (BCM) *CN
21-032-15 REVA
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or describe harsh shifting. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) or symptoms. ? Harsh 1-2 Upshift. ? Harsh Garage Shifts (Park to Reverse or Drive). ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. ? P0887 - TCM Power Control Circuit High. ? P1CC9 - Unable to Engage Gear. ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective. ? U0401 - Implausible Data Received From ECM-PCM.
SB-21-032-15REVA
JEEP: LATEST SOFTWARE IS AVAILABLE TO BE REPROGRAMMED FOR TRANSMISSION CONTROL MODULE (TCM) DUE TO MALFUNCTION INDICATOR LAMP (MIL) BEING ON AND HAVING A HARSH SHIFTING OR TO UNABLE ENGAGED GEARS OF TRANSMISSION. MODEL 2015 RENEGADE. *PE
SB18-043-15REV.A
2015 JEEP RENEGADE: ENGINE CONTROL MODULE NEEDS REPROGRAMMING WITH LATEST SOFTWARE. CUSTOMERS MAY COMPLAIN OF A MALFUNCTION INDICATOR LAMP *CN
08-053-15 REVA
Cluster Backlighting Dimming Incorrectly This bulletin involves replacing and programming the instrument panel cluster. A small number of customer may notice that the cluster illumination is not dimming properly while in day or night modes.
23-020-15 REVA
Replace Missing Manual Release Cover For The Electric Fuel Door This bulletin involves installing a cover for the fuel door manual release cable. The customer may describe a loose cable hanging in the right rear of the cargo compartment area.
23-025-15
Rear Door Glass Stain This bulletin involves removing stains from the rear door glass.
08-066-15
Flash: Improvements To Messages Displayed In The Cluster This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest available software, to improve Forward Collision Warning (FCW) messages. This IPC software update will change the message in the cluster from ?Unavailable Wipe Front Radar Sensor? to ?Front Radar Sensor Temporarily Blocked?.
08-062-15
RA2 Radio Software Enhancements This bulletin involves updating the radio's software. The customer may notice that blue tooth communication with the passenger is poor. If a passenger is trying to talk on the blue tooth phone, the caller will have a hard time understanding what the passenger is saying. The caller will not have any issue understanding the person in the driver?s seat.
08-063-15
Flash: Battery Drained After Sitting Overnight This bulletin involves reprogramming the Heating Ventilation Air Conditioning (HVAC) module with the latest available software. A small number of customers may experience an intermittent dead battery situation when attempting to start the vehicle after sitting overnight. The software in the HVAC module is causing a parasitic draw resulting in the gradual discharge of the battery. This condition is corrected by updating the HVAC with the latest available software.
08-060-15
Doors may not unlock using remote keyless entry.
0806015
Doors may not unlock using remote keyless entry.
21-040-15
Tranmission shift Drivability enhancements.
2104015
Tranmission shift Drivability enhancements.
08-058-15
Reprogramming the Body Control Module with the latest available software.
0805815
Reprogramming the Body Control Module with the latest available software.
21-038-15
Flash: Drivetrain Control Module C2020-01 ECU Internal Fault setting in the DTCM This bulletin involves reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.
08-023-15 REVA
Stored Diagnostic Trouble Codes (DTCs) Found During New Vehicle Preparation
23-020-15
Replace Missing Manual Release Cover For The Electric Fuel Door This bulletin involves installing a cover for the fuel door manual release cable. The customer may describe a loose cable hanging in the right rear of the cargo compartment area.
2302015
Replace Missing Manual Release Cover For The Electric Fuel Door This bulletin involves installing a cover for the fuel door manual release cable. The customer may describe a loose cable hanging in the right rear of the cargo compartment area.
21-032-15
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance ? P0887 - TCM Power Control Circuit High ? P1CC9 - Unable to Engage Gear ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective ? U0401 - Implausible Data Received From ECM-PCM
2103215
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance ? P0887 - TCM Power Control Circuit High ? P1CC9 - Unable to Engage Gear ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective ? U0401 - Implausible Data Received From ECM-PCM
18-043-15
Flash: 2.4L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Engine Control Module (ECM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Code (DTC) P050D - Cold Start Rough Idle stored in the ECM memory. In addition, customers may experience one or more of the following concerns: ? RPM flare at cold start. ? Less than desired idle performance. ? Cold engine RPM surge with gear engagement.
21-030-15
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or both of the following Diagnostic Trouble Codes (DTCs). ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance ? P1DAD - Input Shaft-Output Shaft Direction Correlation ? P1CC9 - Unable to Engage Gear ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective ? U1424 - Implausible Engine Torque Signal Received
2103015
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or both of the following Diagnostic Trouble Codes (DTCs). ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance ? P1DAD - Input Shaft-Output Shaft Direction Correlation ? P1CC9 - Unable to Engage Gear ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective ? U1424 - Implausible Engine Torque Signal Received
08-052-15
Compass Direction Displayed Is 90 Degrees Off This bulletin involves a vehicle reconfiguration and proxi alignment for proper compass direction displayed within the instrument cluster. The customer may notice the compass direction displayed is 90 degrees off (Fig. 1). Fig. 1 Compass 1 - Compass Direction Indicator
08-053-15
Cluster Backlighting Dimming Incorrectly This bulletin involves replacing and programming the instrument panel cluster. A small number of customer may notice that the cluster illumination is not dimming properly while in day or night modes.
D-15-13
Claim Reimbursement Guidelines - Radar Sensor Alignment Tool
08-026-15 REVA
Incorrect Language Displayed On The Cluster And Radio This bulletin involves changing the vehicle language settings to English. The customer and/or dealer may want to change the language displayed in the radio and cluster to English.
08-026-15
Incorrect Language Displayed On The Cluster And Radio This bulletin involves changing the vehicle language settings to English. The customer and/or dealer may want to change the language displayed in the radio and cluster to English.
08-023-15
Stored Diagnostic Trouble Codes (DTCs) Found During New Vehicle Preparation
5ZM61LXHA
Shifter - Automatic Transmission
18-065-14
Flash: MIL Illumination - P1451-00 Set in the ECM Unit This bulletin involves upgrading the software in the Engine Control Module (ECM). The customer may experience MIL light illuminates and DTC P1451-00 ?Diesel Particulate Filter- Efficiency? set in the ECM.
1806514
MIL Illumination - P1451-00 Set in the ECM Unit
23-035-14
Driver Door Lock Cylinder This bulletin involves replacing the driver door lock cylinder housing. The plastic cover of the driver door lock cylinder may be loose or fall off.
2303514
Driver Door Lock Cylinder
08-089-14
Flash: Multiple ECU Software Enhancements This bulletin involves upgrading the software in the Engine Control Module (ECM), the Instrument Panel Cluster (IPC), the Body Control Module (BCM), the Antilock Brake System (ABS), the Electric Steering Lock Module (ESL) and the HVAC Module. The customer may experience one or all of the following: - Fuel consumption indication on the trip computer could be 2% higher than the real value. - The clock of the Radio and displayed by the EVIC loses time. - Start and Stop is sometime erroneously not available. - Excessive battery consumption while the vehicle is set in Logistic Mode. - DTC P0238 ?Turbo boost Pressure Sensor Circuit High?. MIL light illuminates sometime during WOT acceleration. (2.0L Diesel engine only) - Manual Transmission Gear upshift/downshift indicator shown in the EVIC sometime does not work properly. (1.6L Diesel engine only)
0808914
Multiple ECU Software Enhancements
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.