Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
CS2311_TSB_R4
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION: CYLINDER PROTECTOR & DECAL INSTALLATION (CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
PI2102_OWNR_501
Other
PRODUCT IMPROVEMENT CAMPAIGN: OWNER RENOTIFICATION (PI2102 FLIGHT #501) - This document is the owner renotification advising that Kia is conducting an important Product Improvement Campaign to perform a software update on 2010-2011 MY Kia Forte and Forte Koup vehicles equipped with 2.4-liter MPI engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (“ECU”).
CS2311_OWNR_PC201
Other
CUSTOMER SATISFACTION CAMPAIGN: POSTCARD OWNER RENOTIFICATION (CS2311) - This document is the owner renotification advising that Kia is conducting Customer Satisfaction Campaign. Kia has developed a new zinc-reinforced ignition cylinder protector hardware upgrade and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Prior notifications stated that this modification had to be performed by July 1, 2025, but the subject vehicles are now eligible until March 31, 2027, to have the ignition cylinder protector installed—if requested—at no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 19, 2025 through December 31, 2025)
PS797
Other
PITSTOP: TECHNICAL OPERATIONS: EXTERNAL DAMAGE TO ULTRASONIC SENSOR: This Pitstop provides information related to Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a “Warning Lamp’ to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)
PI2102_OWNR_401
Other
PRODUCT IMPROVEMENT CAMPAIGN: OWNER RENOTIFICATION (PI2102) - This document is the owner renotification advising that Kia is conducting a Product Improvement Campaign to perform a software update on 2010-2011 MY Kia Forte and Forte Koup vehicles equipped with 2.4-liter MPI engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (“ECU”).
TSB_TRA046_R5
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: TRANSMISSION FLUID APPLICATION GUIDE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.
PI2102YZ_TSB_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PRODUCT IMPROVEMENT CAMPAIGN: SUBSEQUENT REPAIR ACTION: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI2102Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (PI2102) titled “Knock Sensor Detection System - ECU Logic Improvement” for 2010-2011MY Forte and Forte Koup (TD)vehicles equipped with Theta 2.4L MPI engine, produced from February 24, 2009 through May 31, 2011. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
PI2102_OWNR_301
Other
PRODUCT IMPROVEMENT CAMPAIGN: OWNER RENOTIFICATION (PI2102) - This document is the owner renotification advising that Kia is conducting This bulletin provides information related to the Technical Service Bulletin previously published in (PI2101) titled “Knock Sensor Detection System - ECU Logic Improvement” for 2011MY Sorento (XMa) vehicles equipped with Theta 2.4L MPI engine, produced from October 24, 2009 through June 24, 2011. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
CS2311_TSB_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION CYLINDER PROTECTOR & DECAL INSTALLATION (CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
TSB_TRA046_R4
Service Bulletin/Repair Instructions
This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced.
PI2102_OWNR_201
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: OWNER RENOTIFICATION (PI2102) - This document is the owner renotification advising that Kia is conducting a Product Improvement Campaign to perform a software update on 2010-2011 MY Kia Forte & Forte Koup vehicles equipped with 2.4-liter engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").
CS2311_TSB_R2
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION CYLINDER PROTECTOR & DECAL INSTALLATION (CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
CS2311A_OWNRTD
Service Bulletin/Repair Instructions
CUSTOMER SATISFACTION CAMPAIGN: OWNER NOTIFICATION - This document is the owner notification advising that Kia now has an additional vehicle modification available for installation to help deter or thwart attempted thefts. This modification consists of a theft deterrent ignition cylinder protector and will be available to you free of charge for eighteen (18) months from the date of this letter.
CS2311_TSB_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION CYLINDER PROTECTOR & DECAL INSTALLATION (CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
CS2311_TSB
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION CYLINDER PROTECTOR & DECAL INSTALLATION (CS2311) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 13, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
CS2305L_OWNRTD2
Service Bulletin/Repair Instructions
CUSTOMER SATISFACTION CAMPAIGN: OWNER RE-NOTIFICATION - This document is the owner re-notification advising that Kia is now making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.
CS2305L_OWNRTD
Service Bulletin/Repair Instructions
CUSTOMER SATISFACTION CAMPAIGN: OWNER NOTIFICATION - This document is the owner notification advising that Kia is now making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.
CS2305L_OWNRYD
Service Bulletin/Repair Instructions
CUSTOMER SATISFACTION CAMPAIGN: OWNER NOTIFICATION - This document is the owner notification advising that Kia is now making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.
TSB_TRA046_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: TRANSMISSION FLUID APPLICATION GUIDE - This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.
PI2102YZ_TSB
Service Bulletin/Repair Instructions
SUBSEQUENT REPAIR ACTION: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI2102Y/Z) - This bulletin provides information related to the Technical Service Bulletin previously published in (PI2102) titled "Knock Sensor Detection System - ECU Logic Improvement" for 2010-2011MY Forte and Forte Koup (TD) vehicles equipped with Theta 2.4L MPI engine, produced from February 24, 2009 through May 31, 2011. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
TSB_CHA084_R8
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.
TSB_BOD055_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: INFORMATION FOR HEADLAMP CONDENSATION AND MOISTURE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.
PI2102_OWNR
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: OWNER NOTIFICATION - This document is the owner notification advising that Kia is conducting a Product Improvement Campaign to perform a software update on 2010-2011 MY Kia Forte and Forte Koup vehicles equipped with 2.4-liter MPI engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU") (PI2102).
PI2102_TSB
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: THETA 2.4L MPI - KNOCK SENSOR DETECTION SYSTEM (KSDS) ECU LOGIC IMPROVEMENT (PI2102) - This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
PI2102_DP
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: DEALER PRINCIPAL MEMO - This document is the announcement to the dealer principals that Kia is conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on 2010-2011 MY Forte and Forte Koup vehicles equipped with 2.4-liter engines, manufactured from February 24, 2009 through May 31, 2011 (PI2102).
PI2102_DSM
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: DEALER PARTS AND SERVICE MANAGER MEMO - This document is the announcement to the dealer Parts and Service Managers that Kia is conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on 2010-2011 MY Forte and Forte Koup vehicles equipped with 2.4-liter engines, manufactured from February 24, 2009 through May 31, 2011 (PI2102).
PI2102_QA
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: QUESTION AND ANSWER - This document is the Question and Answer Guide containing the most frequently asked questions regarding the Product Improvement Campaign (PI2102).
TSB_CHA084_R7
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
TSB_CHA084_R6
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
TSB_CHA084_R5
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
PS675
Service Bulletin/Repair Instructions
PITSTOP - BRAKE CALIPER LEAK INSPECTION - This PITSTOP provides information related to a brake caliper fluid/oil substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.
TSB_TRA046_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: - TRANSMISSION FLUID APPLICATION GUIDE - This bulletin has been revised to include additional information. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.
TSB_ELE148
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: HALOGEN HEAD LAMP LOW BEAM BULB CONNECTOR REPLACEMENT - This bulletin provides information regarding the procedure to repair the bulb connector on some 2010MY~ vehicles listed on the table below, which may exhibit a bulb connector concern. To correct this concern, replace the connector with a new and improved part.
TSBCHA084_R4
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.
TSBCHA084_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN TSB084_R3: PARTIAL REPAIR OF C-MDPS MOTOR, ECU AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
TSBBOD079_CLOSED
Service Bulletin/Repair Instructions
TSB: SERVICE ACTION: APPLICATION OF ADDITIONAL ANTICORROSION PROTECTION THROUGH PROTECTIVE SEALING (SA085) - CLOSED
PS067_R1
Service Bulletin/Repair Instructions
PITSTOP: CYLINDER HEAD STEEL BALL INSPECTION AND INSTALLATION - This Pitstop provides information regarding the inspection and installation of the steel sealing ball on: * 3.3L & 3.8L Lambda engines for 2007-2008MY Sorento (BL), * 2.0L Nu engines for 2010-2019MY Soul (AM, PS), and * 1.8L & 2.0L Nu engines for 2010-2018MY Forte (TD, YD/YDm), 2019MY~ Forte (BDm). When replacing the cylinder heads on these engines, inspect the lubrication ports for installation of the steel sealing balls. Current replacement cylinder heads may not be equipped with the required steel balls. Identify and locate the nine (9) lubricant passages on 3.3L and 3.8L engines and three (3) on 1.8L and 2.0L engines and verify a steel ball is installed in each.
PS539
Service Bulletin/Repair Instructions
PITSTOP - ENGINE COMPONENT RE-USE GUIDELINES - In general, parts and components removed during engine repairs should be considered serviceable, and should be thoroughly cleaned and transferred to the new engine.
TSBTRA047_R2
Service Bulletin/Repair Instructions
TSB - DRIVESHAFT SERVICEABILITY - This bulletin has been revised most recently to include additional information. This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.
TSBELE091R3
Service Bulletin/Repair Instructions
TSB - IDENTIFYING HEAD UNIT SOFTWARE VERSION FOR DIRECT EXCHANGE - This bulletin provides the procedure on how to identify and record the head unit software level on various head unit platforms and generations.
PS474
Service Bulletin/Repair Instructions
PITSTOP: TPMS SENSOR POSITION - When diagnosing TPMS-related DTCs, make sure you are investigating the correct sensor. The TPMS positioning from the manufacturer may be different from the positioning shown on a KDS.
PS493
Service Bulletin/Repair Instructions
TSB: DEFOGGING LOGIC ? NORMAL OPERATION, DISABLING, AND ENABLING - Starting with 2010MY, all Kia vehicles, except Rio (JB), incorporate a defogging logic to prevent the interior windows from becoming excessively fogged. Depending on the specific model, the HVAC control head monitors ambient temperature and/or cabin humidity to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature or higher cabin humidity, the defogging logic may automatically switch ON the A/C, and/or set the air intake mode to Fresh Air. If the user changes these settings, the defogging logic will take control again after 3 to 5 minutes, depending on the procedure in this publication.
TSB-SC141R1
Service Bulletin/Repair Instructions
TSB: SC141 - SERVICE CAMPAIGN - APPLICATION OF ADDITIONAL ANTI-CORROSION MATERIAL - To improve customer satisfaction, Kia is launching this service campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014MY Sorento, 2011-2014MY Optima and Optima Hybrid, 2011-2014MY Sportage, and 2010-2013MY Forte and Forte Koup vehicles originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.
PS469
Service Bulletin/Repair Instructions
PITSTOP: MANUAL EVAPORATIVE EMISSIONS TEST FOR HARD TO FIND/SMALL LEAKS - If the malfunction indicator lamp (MIL) is illuminated with DTC(s) P0442, P0455, P0456, or P0457 (Evaporative Emissions System-Leak detected) and the evaporative (EVAP) leak self-test resulted in NTF, a manual EVAP test is recommended.
TSB-GEN085R1
Service Bulletin/Repair Instructions
TSB: MANDATORY REPLACEMENT OF LOCKING/SECURITY HARDWARE - By design, certain fasteners, which are designed to lock into place once fully attached, are utilized in various Kia models and are strictly intended for ?one time use.? Some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.? It is critical for technicians to be aware that ALL such locking fasteners, regardless of type, are for ?one time use? only.
SC141OWNERTD
Service Bulletin/Repair Instructions
SERVICE CAMPAIGN: OWNER LETTER - Advises Owners of certain 2011-2013 MY Forte and Forte Koup vehicles currently registered in the states where heavy amounts of road salt are used of a service campaign to add additional anti-corrosion material to underbody components of vehicle.
TSB-SC141
Service Bulletin/Repair Instructions
TSB: SC141 - SERVICE CAMPAIGN - APPLICATION OF ADDITIONAL ANTI-CORROSION MATERIAL - To improve customer satisfaction, Kia is launching this service campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014MY Sorento, 2011-2014MY Optima and Optima Hybrid, 2011-2014MY Sportage, and 2010-2013MY Forte and Forte Koup vehicles originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.
SC141DP
Service Bulletin/Repair Instructions
DEALER PRINCIPAL MEMO: SC141 - SERVICE CAMPAIGN - Attention: All Kia Dealer Principals - Kia Motors America, Inc. will be conducting a Voluntary Service Campaign, as a preventative measure, to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento, 2011-2014 MY Optima and Optima Hybrid, 2011-2014 MY Sportage, and 2010-2013 Forte and Forte Koup vehicles originally retailed or currently registered in one of the 28 states where heavy amounts of road salt are used.
SC141DPSM
Service Bulletin/Repair Instructions
SERVICE MANAGER MEMO: SC141 - SERVICE CAMPAIGN - Attention: All Kia Service Managers - Kia Motors America, Inc. will be conducting a Voluntary Service Campaign, as a preventative measure, to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento, 2011-2014 MY Optima and Optima Hybrid, 2011-2014 MY Sportage, and 2010-2013 Forte and Forte Koup vehicles originally retailed or currently registered in one of the 28 states where heavy amounts of road salt are used.
SC141QA
Service Bulletin/Repair Instructions
QUESTIONS AND ANSWERS FOR VOLUNTARY SERVICE CAMPAIGN SC141 ? UNDERBODY ? ADDITIONAL ANTI-CORROSION TREATMENT
TSB-GEN085
Service Bulletin/Repair Instructions
TSB: MANDATORY REPLACEMENT OF LOCKING/SECURITY HARDWARE - By design, certain fasteners utilized in various Kia models are strictly intended for ?one time use?. Though not limited to the following, some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.?
TSB-TRA055
Service Bulletin/Repair Instructions
TSB: INHIBITOR SWITCH DIAGNOSIS INFORMATION - This bulletin gives information regarding the steps to take regarding the diagnosis of the Inhibitor Switch.
PS266R1
Service Bulletin/Repair Instructions
PITSTOP: HVAC RECEIVER/DRYER - DESICCANT REPLACEMENT - IN THE EVENT OF A HVAC SYSTEM CONCERN IN WHICH METAL PARTICLES OR SHARDS HAVE CONTAMINATED THE SYSTEM, THE DESICCANT OR THE ENTIRE A/C RECEIVER/DRYER ASSEMBLY MAY NEED TO BE REPLACED. THIS IS DUE TO THE FACT THAT IT MAY BE IMPOSSIBLE TO REMOVE ALL METAL CONTAMINANTS FROM THE RECEIVER/DRYER DURING THE A/C FLUSHING PROCEDURE. REFER TO THE INCLUDED TABLE FOR DETAILED INFORMATION ON COMPONENT REPLACEMENT BY MODEL. IF YOU SUSPECT A PLUGGED EXPANSION VALVE, THE INLET SCREENS CAN BE CLEANED. IF THE VALVE IS NOT EQUIPPED WITH AN INLET SCREEN AND IS RESTRICTED, THE EXPANSION VALVE MAY ALSO NEED TO BE REPLACED.
PS443
Service Bulletin/Repair Instructions
TSB - USE OF AFTERMARKET USB CHARGING CABLES IN USB/12V PORTS - This article provides information regarding the use of USB ports and 12V power outlets to connect/charge mobile phones. Customers may experience issues with their head units that may be related to the use of aftermarket USB charging cables, including; * Electrical interference and limited or no functionality when attempting to play music, or when charging a device through the USB port * Excessive static or noise when listening to the audio source * Malfunctions and screen freeze of the head unit screen * Slow down of the system response while device is plugged in * Music will not play from iPhone 5 or 6 with Kia iPod cable and aftermarket adapter * No or limited functionality when trying to play music from an Apple device
TSB SC129
Service Bulletin/Repair Instructions
THIS BULLETIN PROVIDES THE PROCEDURE TO REPLACE THE A/T COOLER HOSES IN CERTAIN 2011 MY FORTE (TD) VEHICLES PRODUCED FROM AUGUST 27, 2010 THROUGH NOVEMBER 11, 2010. THE AUTOMATIC TRANSMISSION FLUID COOLER HOSES MAY HAVE BEEN IMPROPERLY CURED DURING THE MANUFACTURING PROCESS. THIS CONDITION MAY RESULT IN THE LOSS OF TRANSMISSION FLUID. IF SUFFICIENT FLUID IS LOST, THE LOSS OF HYDRAULIC PRESSURE TO THE TRANSAXLE COULD RESULT IN REDUCED VEHICLE MOBILITY. TO CORRECT THIS CONDITION FOLLOW THE PROCEDURE OUTLINED IN THIS BULLETIN.
TSBSC129
Service Bulletin/Repair Instructions
VOLUNTARY SAFETY RECALL CAMPAIGN: A/T FLUID COOLER HOSE REPLACEMENT (SC 129) - THIS BULLETIN PROVIDES THE PROCEDURE TO REPLACE THE A/T COOLER HOSES IN CERTAIN 2011 MY FORTE (TD) VEHICLES PRODUCED FROM AUGUST 27, 2010 THROUGH NOVEMBER 11, 2010. THE AUTOMATIC TRANSMISSION FLUID COOLER HOSES MAY HAVE BEEN IMPROPERLY CURED DURING THE MANUFACTURING PROCESS. THIS CONDITION MAY RESULT IN THE LOSS OF TRANSMISSION FLUID. IF SUFFICIENT FLUID IS LOST, THE LOSS OF HYDRAULIC PRESSURE TO THE TRANSAXLE COULD RESULT IN REDUCED VEHICLE MOBILITY. TO CORRECT THIS CONDITION FOLLOW THE PROCEDURE OUTLINED IN THIS BULLETIN.
TSBSC126
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: ENGINE CONTROL MODULE SOFTWARE UPDATE (SC 126) - THIS BULLETIN PROVIDES INFORMATION RELATED TO UPDATING THE SOFTWARE PROGRAMMING (CALIBRATION) OF THE ENGINE CONTROL MODULE (ECM) ON SOME 2011MY OPTIMA (TF) VEHICLES EQUIPPED WITH A 2.4L ENGINE AND CALIFORNIA EMISSIONS, PRODUCED FROM OCTOBER 14, 2010 THROUGH SEPTEMBER 9, 2011, WHICH MAY HAVE ENGINE CALIBRATIONS THAT WERE NOT OPTIMIZED FOR EMISSIONS WHEN THE VEHICLE IS WARMING UP. THESE CALIBRATIONS MAY CAUSE THE VEHICLE TO RELEASE AIR POLLUTANTS WHICH EXCEED CALIFORNIA AIR RESOURCE BOARD (CARB) EMISSIONS REGULATIONS. TO CORRECT THIS CONDITION, KIA IS REQUESTING THE COMPLETION OF THIS VOLUNTARY EMISSIONS SERVICE CAMPAIGN ON ALL AFFECTED 2011MY OPTIMA (TF) VEHICLES. FOR CONFIRMATION THAT THE LATEST REFLASH HAS BEEN DONE TO A VEHICLE YOU ARE WORKING ON, VERIFY THE ROM ID USING THE TABLES IN THIS TSB.
TSBSST041
Service Bulletin/Repair Instructions
TSB: KDS - AUDIO UPDATE MODULE (AUM) - THE GDS AUDIO UPDATE MODULE (AUM) WAS INTRODUCED IN FOURTH QUARTER OF 2013. THIS SPECIAL SERVICE TOOL (SST) WAS DEVELOPED TO IMPROVE THE EFFICIENCY AND EFFECTIVENESS OF UPDATING 2010MY, AND LATER, KIA AUDIO HEAD UNITS USING A GDS, AND NOW, THE SAME FUNCTIONALITY IS AVAILABLE ON KDS. SOME TECHNICIANS MAY NOT BE AWARE OF THE BENEFITS THE AUM TOOL HAS TO OFFER. THE AUM ELIMINATES THE NEED FOR MULTIPLE USB FLASH DRIVES FOR SPECIFIC VEHICLE MODELS AND APPLICATIONS WHICH, IF MISAPPLIED, MAY RESULT IN AN IMPROPER AUDIO SYSTEM SOFTWARE UPDATE AND/OR LOCKED UP HEAD UNIT. ADDITIONALLY, FIELD REPORTS HAVE INDICATED THAT USB DRIVES FOR AUDIO UPDATES ARE EASILY LOST OR MISPLACED.
TSB-ELE091R1
Service Bulletin/Repair Instructions
TSB: IDENTIFYING HEAD UNIT SOFTWARE VERSION FOR DIRECT EXCHANGE - Identifying Head Unit Software Version For Direct Exchange (ELE091) (Rev 1) - This bulletin provides the procedure on how to identify and record the head unit software level on various head unit platforms and generations. This procedure will now be required when ordering head units through the Direct Exchange Program (see Parts Bulletin 91-961-0005).
TSBELE091
Service Bulletin/Repair Instructions
TSB: IDENTIFYING HEAD UNIT SOFTWARE VERSION FOR DIRECT EXCHANGE - THIS BULLETIN PROVIDES THE PROCEDURE ON HOW TO IDENTIFY AND RECORD THE HEAD UNIT SOFTWARE LEVEL ON VARIOUS HEAD UNIT PLATFORMS AND GENERATIONS. THIS PROCEDURE WILL NOW BE REQUIRED WHEN ORDERING HEAD UNITS THROUGH THE DIRECT EXCHANGE PROGRAM.
TSBTRA049R1
Service Bulletin/Repair Instructions
TSB: 6-SPD. A/T ADAPTIVE VALUE RESET /RELEARN - THIS BULLETIN PROVIDES THE PROCEDURES NECESSARY TO RESET AND RELEARN THE ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE PCM/TCM. AFTER THE ADAPTIVE VALUES ARE RESET, THE TRANSMISSION COMPUTER ADAPTIVE VALUES MUST BE RELEARNED BY DRIVING IN A PRECISE MANNER TO TEACH THE COMPUTER THE PROPER SOLENOID DUTY AND LINE PRESSURE FOR THE NEW TRANSMISSION/COMPUTER COMBINATION.
TSBTRA051R1
Service Bulletin/Repair Instructions
TSB: 6 SPD A/T SOLENOID REPLACEMENT MULTIPLE DTCS - THIS BULLETIN PROVIDES INFORMATION RELATING TO THE REPLACEMENT OF VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.
055
Service Bulletin/Repair Instructions
KIA : SOME VEHICLES EXPERIENCING NO CRANK OR START, MIL LAMP, HARSH SHIFTING, DEPRESSING THE START/STOP BUTTON TWICE. *LJ
TSB-TRA051
Service Bulletin/Repair Instructions
TSB: 6 SPD A/T SOLENOID REPLACEMENT ? DTC P0741 - This bulletin provides information relating to the replacement of the Damper Clutch (D/C) Solenoid on 6-speed automatic transaxles with DTC P0741 (active or history), instead of replacing the transaxle. To reduce vehicle repair time, this procedure can be performed with the transaxle installed in the vehicle.
TSBTRA046
Service Bulletin/Repair Instructions
TSB: AUTOMATIC TRANSMISSION FLUID APPLICATION GUIDE - THIS BULLETIN PROVIDES INFORMATION RELATING TO THE CORRECT AUTOMATIC TRANSMISSION FLUIDS THAT ARE REQUIRED FOR EACH KIA MODEL. REFER TO THE SHOP MANUAL ON KGIS FOR THE SPECIFIC KIA MODEL, THEN REFERENCE THE AUTOMATIC TRANSAXLE SYSTEM/ REPAIR PROCEDURES/ INSPECTION AND ADJUSTMENT SECTION FOR THE CORRECT ATF CHECK/FILL PROCEDURES.
PS274
Service Bulletin/Repair Instructions
PITSTOP: ACU VARIANT CODING AFTER PARTS SUPERSESSION - KMA HAS RECEIVED REPORTS OF SOME 2011~13MY OPTIMA AND 2010~13MY FORTE VEHICLES NOT ACCEPTING THE VARIANT CODE LISTED ON KGIS, FOLLOWING REPLACEMENT OF THE AIR BAG CONTROL MODULE. IN SOME CASES, AN AIR BAG MODULE WITH A SUPERSEDED PART NUMBER MAY REQUIRE A DIFFERENT VARIANT CODE. KGIS IS BEING UPDATED IN PHASES AND WILL LIST BOTH VARIANT CODES (OLD AND NEW) IN CASE OF P/N SUPERSESSION.
TSBTRA049
Service Bulletin/Repair Instructions
TSB: 6-SPEED A/T TRANSMISSION ADAPTIVE VALUES RESET/RELEARN - THIS BULLETIN PROVIDES THE PROCEDURES NECESSARY TO RESET AND RELEARN THE ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE ECM/PCM.
TSBBOD095
Service Bulletin/Repair Instructions
TSB: WINDSHIELD WASHER PUMP INLET FILTER REPLACEMENT - THIS BULLETIN PROVIDES INFORMATION RELATING TO POSSIBLE FOREIGN DEBRIS ACCUMULATION ON THE WINDSHIELD WASHER PUMP INLET FILTER. OVER TIME, SOME KIA VEHICLES MAY EXHIBIT A LIMITED APPLICATION OF WINDSHIELD WASHER FLUID WHEN THE WASHER FUNCTION IS USED. LIMITED APPLICATION OF WINDSHIELD WASHER FLUID CAN BE CAUSED BY FOREIGN DEBRIS ON THE WASHER PUMP INLET FILTER. TO CORRECT THIS CONDITION, REPLACE THE WASHER PUMP INLET FILTER AND PERFORM THE WINDSHIELD WASHER RESERVOIR FLUSHING PROCEDURE OUTLINED IN THIS TSB.
PS267
Service Bulletin/Repair Instructions
PITSTOP: THERMOSTAT RE-INSTALLATION PROCEDURE - REPEAT REPAIR (DTC P0128) - WHEN DIAGNOSING A FORTE RETURNING WITH A REPEAT DTC P0128 AFTER REPLACEMENT OF THE THERMOSTAT, REMOVE THE THERMOSTAT HOUSING TO VERIFY IF THE THERMOSTAT WAS INSTALLED INCORRECTLY DURING THE PREVIOUS REPAIR.
TSBTRA047R1
Service Bulletin/Repair Instructions
TSB: AXLE SHAFT SERVICEABILITY BY MODEL - THIS BULLETIN HAS BEEN REVISED. THIS BULLETIN PROVIDES INFORMATION REGARDING AXLE SHAFT SERVICEABILITY FOR KIA VEHICLES EQUIPPED WITH A SIX-SPEED AUTOMATIC TRANSMISSION. REFER TO THE TABLE BELOW FOR A DETAILED LIST OF VEHICLE MODELS. INDIVIDUAL SERVICE PARTS SUCH AS AXLE BOOTS, JOINTS AND HARDWARE FOR INNER JOINT ARE NOW AVAILABLE THROUGH YOUR PARTS DEPARTMENT.
PS223
Service Bulletin/Repair Instructions
PITSTOP: FORTE LOCK CONFIRMATION INOP WITH REMOTE START ACCESSORY - SOME REMOTE START EQUIPPED FORTES MAY NOT INDICATE THAT THE DOORS HAVE BEEN LOCKED. THE CUSTOMER MAY STATE THAT THE VEHICLE WILL NOT FLASH THE HAZARD LIGHTS OR SOUND THE HORN WHEN LOCKING THE DOORS WITH THE TRANSMITTER. AS DESIGNED, THE VEHICLE SHOULD FLASH THE HAZARD LIGHTS AND SOUND THE HORN AFTER PRESSING THE LOCK BUTTON TWO (2) TIMES WITHIN FIVE (5) SECONDS. IF THIS CONCERN IS OCCURRING, VERIFY IF IT IS RELATED TO THE REMOTE START CONTROL MODULE BY CHECKING THE POSITION OF THE OVERHEAD INTERIOR LIGHT SWITCH. IF THE SWITCH IS IN THE OFF POSITION, MOVE THE SWITCH TO THE DOOR POSITION AND RETEST THE SYSTEM.
TSB-036-01
Service Bulletin/Repair Instructions
KIA: THIS BULLETIN PROVIDES INFORMATION RELATED TO EPS ECM SOFTWARE UPGRADE. *JS
112
Service Bulletin/Repair Instructions
KIA: VCM ACTUATOR REPLACEMENT AND ECM UPGRADE-TD/SL 2.0/2.4L MIL ON WITH DTC P200A. *KB
TSB-023
Service Bulletin/Repair Instructions
KIA: INFORMATION HAS BEEN PROVIDED REGARDING THE REPLACEMENT OF THE NEGATIVE (-) AND THE POSITIVE (+) BATTERY CABLE TERMINAL FOR SOME VEHICLES. *PE
TSB-083
Service Bulletin/Repair Instructions
KIA: FOR GDI HIGH PRESSURE FUEL SYSTEM, SPECIAL SERVICE INFORMATION AND SPECIFICATIONS ARE PROVIDED. *PE
TSB-015
Service Bulletin/Repair Instructions
KIA MOTORS: INSTALLING AN ADDITIONAL GROUND CABLE TO THE BATTERY MAY CAUSE SENSOR PROBLEMS. *RM
TSB-073
Service Bulletin/Repair Instructions
KIA: INFORMATION ON REPLACING THE AIRBAG CONTROL UNIT. *RM