Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
WTY031_TSB_R2
Warranty Program/Extension
TECHNICAL SERVICE BULLETIN: WARRANTY EXTENSION CAMPAIGN: MULTIFUNCTION SWITCH REPAIR (WTY031) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information associated with the ‘Multifunction Switch Warranty Extension Program’ (WTY031) to repair the multifunction switch knob on 2016-2018MY Sorento (UMa) vehicles, produced at Kia Georgia from October 27, 2014 through March 7, 2018, which may exhibit an intermittent headlamp flickering. The vehicle’s warranty for this issue will be extended from 5 years/60,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service.
CS2312_TSB_R2
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION CYLINDER PROTECTOR AND DECAL INSTALLATION (CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
SC340_TSB_R5
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: THETA II 2.4L GDI EMISSIONS: ECM LOGIC IMPROVEMENT (SC340 REVISION 5) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to upgrade the Electronic Control Module ‘ECM’ system software for certain 2016-2020MY Optima, 2016-2020MY Sorento, 2017-2022MY Sportage vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.
WTY026_TSB_R2
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: WARRANTY EXTENSION CAMPAIGN: OIL PRESSURE SWITCH (OPS) REPLACEMENT (WTY026 REVISION 2) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the replacement of the Oil Pressure Switch associated with the ‘Warranty Extension Program’ (WTY026) on some 2014-2018MY vehicles listed in the table below, for repairs that may be necessary to address an Oil Pressure Switch leak in the eligible vehicles listed below from 10 years/100,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. This warranty extension is to address the Oil Pressure Switch leaking condition at no cost to the customers during this extended warranty period.
SC340_TSB_R4
Emissions
TECHNICAL SERVICE BULLETIN: VOLUNTARY EMISSIONS SERVICE CAMPAIGN: THETA II 2.4L GDI EMISSION SECM LOGIC IMPROVEMENT (SC340 REV 4) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to upgrade the Electronic Control Module ‘ECM’ system software for certain 2016-2022MY vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.
TSB_CS2312_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION CYLINDER PROTECTOR AND DECAL INSTALLATION (CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whole Integrated Body control Unit (IBU) / Body Control Module (BCM) did receive the Ant-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
SC340_OWNR_UM103
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: OWNER NOTIFICATION (SC340 FLIGHT 103 / UM) - This document is the owner notification advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) for certain 2016-2020 MY Sorento vehicles equipped with 2.4L Gas Direct Injection (GDI) engines to ensure compliance with emissions regulations.
TSB_CS2312
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION CYLINDER PROTECTOR AND DECAL INSTALLATION (CS2312) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 19, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
CS2312_OWNR
Other
CUSTOMER SATISFACTION CAMPAIGN: OWNER NOTIFICATION (CS2312) - This document is the owner notification advising that Kia is conducting Customer Satisfaction Campaign. A software upgrade that addresses the social media theft method has been made available to owners of eligible Kia model vehicles free of charge at authorized Kia dealers since 2023. In addition to the anti-theft software, a new zinc-reinforced ignition cylinder protector hardware upgrade has been developed and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because the subject Kia vehicles were not factory-equipped with an engine immobilizer and were previously eligible for the software upgrade, these vehicles are eligible until March 31, 2027, to have the ignition cylinder protector installed—if requested—at no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 17, 2025 through February 27, 2026)
SC340_TSB_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: VOLUNTARY EMISSIONS SERVICE CAMPAIGN: THETA II 2.4L GDI EMISSIONS ECM LOGIC IMPROVEMENT (SC340) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to upgrade the Electronic Control Module ‘ECM’ system software for certain 2016-2022MY vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.
PS797
Other
PITSTOP: TECHNICAL OPERATIONS: EXTERNAL DAMAGE TO ULTRASONIC SENSOR: This Pitstop provides information related to Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a “Warning Lamp’ to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)
SC340_OWNR_UM101
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: OWNER NOTIFICATION (SC340 FLIGHT 101 / UM) - This document is the owner notification advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) for certain 2016-2020 MY Sorento vehicles equipped with 2.4L Gas Direct Injection (GDI) engines to ensure compliance with emissions regulations.
SC340_TSB_R2
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: VOLUNTARY EMISSIONS SERVICE CAMPAIGN: THETA II 2.4L GDI EMISSIONS ECM LOGIC IMPROVEMENT (SC340) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to upgrade the Electronic Control Module ‘ECM’ system software for certain 2016-2022MY vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.
SC340_TSB_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: VOLUNTARY SERVICE CAMPAIGN: THETA II 2.4L GDI EMISSIONS ECM LOGIC IMPROVEMENT (SC340) - This bulletin has been revised to include additional information. New / revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to upgrade the Electronic Control Module ‘ECM’ system software for certain 2016-2022MY vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.
SC340_TSB
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: VOLUNTARY EMISSIONS SERVICE CAMPAIGN: THETA II 2.4L GDI EMISSIONS ECM LOGIC IMPROVEMENT (SC340) - This bulletin provides information to upgrade the Electronic Control Module ‘ECM’ system software for certain 2016-2022MY vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.
SC340_DP
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: DEALER PRINCIPAL MEMO (SC340) - This document is the announcement to the dealer principals advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) to ensure compliance with emissions regulations in certain 2017-2022 MY Sportage vehicles manufactured from December 10, 2015, through December 7, 2021, certain 2016-2020 MY Optima vehicles manufactured from August 28, 2015, through June 23, 2020, and certain 2016-2020 MY Sorento vehicles manufactured from October 27, 2014, through November 4, 2020, equipped with 2.4L Theta GDI engines.
SC340_DPSM
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: DEALER PARTS AND SERVICE MANAGER MEMO (SC340) - This document is the announcement to the dealer Parts and Service managers advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) to ensure compliance with emissions regulations in certain 2017-2022 MY Sportage vehicles manufactured from December 10, 2015, through December 7, 2021, certain 2016-2020 MY Optima vehicles manufactured from August 28, 2015, through June 23, 2020, and certain 2016-2020 MY Sorento vehicles manufactured from October 27, 2014, through November 4, 2020, equipped with 2.4L Theta GDI engines.
SC340_POC
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: SC340_POC: PROOF OF CORRECTION CARD
SC340_QA
Emissions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: QUESTION AND ANSWER (SC340) - This document is the Question and Answer Guide containing the most frequently asked questions regarding the Voluntary Emissions Service Campaign SC340.
SC340_STKR
Emissions
SC340_STKR: VOLUNTARY EMISSIONS SERVICE CAMPAIGN COMPLETION LABEL/STICKER
SC330_OWNR_201
Service Campaign
VOLUNTARY SERVICE CAMPAIGN: OWNER RENOTIFICATION (SC330) - This document is the owner renotification advising that Kia is conducting a Voluntary Service Campaign to replace the multi-function switch knob with improved parts on certain 2016-2018 MY Sorento vehicles.
TSB_TRA046_R5
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: TRANSMISSION FLUID APPLICATION GUIDE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.
TSB_ENG222_R8
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA/KAPPA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the table on pages 9 and 10 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.
TSB_ENG222_R7
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA/KAPPA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.
SC330_OWNR
Service Campaign
VOLUNTARY SERVICE CAMPAIGN: OWNER NOTIFICATION (SC330) - This document is the owner notification advising that Kia conducting a Voluntary Service Campaign to replace the multi-function switch knob with improved parts on certain 2016-2018 MY Sorento vehicles, manufactured from October 27, 2014 through March 7, 2018.
SC330_DP
Service Campaign
VOLUNTARY SERVICE CAMPAIGN: DEALER PRINCIPAL MEMO (SC330) - This document is the announcement to the dealer principals advising that Kia is conducting a Voluntary Service Campaign to replace the multi-function switch knob with improved parts on certain 2016-2018 MY Sorento vehicles, manufactured from October 27, 2014 through March 7, 2018.
SC330_DPSM
Service Campaign
VOLUNTARY SERVICE CAMPAIGN: DEALER PARTS AND SERVICE MANAGER MEMO (SC330) - This document is the announcement to the dealer Parts and Service managers advising that Kia is conducting a Voluntary Service Campaign to replace the multi-function switch knob with improved parts on certain 2016-2018 MY Sorento vehicles, manufactured from October 27, 2014 through March 7, 2018.
SC330_QA
Service Campaign
VOLUNTARY SERVICE CAMPAIGN: QUESTION AND ANSWER (SC330) - This document is the Question and Answer Guide containing the most frequently asked questions regarding the Voluntary Service Campaign SC330.
SC330_TSB
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: VOLUNTARY SERVICE CAMPAIGN: MULTI-FUNCTION SWITCH REPAIR (SC330) - This bulletin provides information to repair the multi-function switch knob on certain 2016-2018MY Sorento (UMa) vehicles manufactured from October 27, 2014 through March 7, 2018. The contact points in the multi-function switch in the subject vehicles may become worn over time, which may result in intermittent headlamp flickering.
WTY031_OWNR301
Warranty Program/Extension
WARRANTY EXTENSION CAMPAIGN: OWNER RENOTIFICATION (WTY031) - This document is the owner renotification advising that Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for the multi-function switch assembly on 2018 MY Sorento vehicles from 5 years / 60,000 miles to 15 years / 150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. The contact points in the multi-function switch in your vehicle may become worn, and it could result in intermittent headlamp flickering.
CS2304_TSB_R7
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked with the use of the key fob.
TSB_TRA046_R4
Service Bulletin/Repair Instructions
This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced.
PI1802YZ_TSB_R7
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement"; equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
WTY031_TSB_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: MULTIFUNCTION SWITCH REPAIR - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information associated with the "Multifunction Switch Warranty Extension Program" (WTY031) to repair the multifunction switch knob on 2016-2018MY Sorento (UMa) vehicles, produced at Kia Georgia from October 27, 2014 through March 7, 2018, which may exhibit an intermittent headlamp flickering. The vehicle's warranty for this issue will be extended from 5 years/60,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. The concern does not need to be duplicated in order to follow the procedure outlined in this publication to replace the multifunction switch moving block and outer cover with the new improved part.
WTY031_OWNR181
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: OWNER RE-NOTIFICATION - This document is the owner re-notification advising that Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for the multi-function switch assembly on 2018 MY Sorento vehicles from 5 years / 60,000 miles to 15 years / 150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. The contact points in the multi-function switch in your vehicle may become worn, and it could result in intermittent headlamp flickering.
CS2304_TSB_R6
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.
PS750
Service Bulletin/Repair Instructions
PITSTOP: AWD SYSTEM CONCERN DUE TO TIRE CIRCUMFERENCE - This Pitstop provides information regarding potential concerns with the All-Wheel-Drive (AWD) system due to tire sizes of differing circumference. Some customers may complain of a chatter sensation felt in the drivetrain of the vehicle and/or the failure of drivetrain component(s). A difference in tire size (width, aspect ratio, construction, rim diameter etc.) may be the cause.
CS2304_TSB_R5
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.
CS2310_TSB_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: KIA GENUINE REMOTE START CONTROL MODULE UPGRADE FOR ANTI-THEFT LOGIC COMPATIBILITY (CS2310) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 7. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.
CS2304B_OWNR2
Service Bulletin/Repair Instructions
CUSTOMER SATISFACTION CAMPAIGN: OWNER RE-NOTIFICATION - This document is the owner re-notification advising that Kia has developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.
CS2304_TSB_R4
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.
TSB_FUE064
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: FUEL PUMP INSPECTION AND UPPER FUEL PUMP MODULE REPLACEMENT - This bulletin provides information associated with the 'Fuel Pump Warranty Extension Program' (WTY033) to inspect the low-pressure fuel pump on 2018-2019MY Sorento (UMa) vehicles produced from March 31, 2017 through July 24, 2019. The low-pressure fuel pump in the subject vehicles may develop a fuel leak over time and after prolonged exposure to extreme high temperature due to insufficient thickness of the fuel pump port. The vehicleâÂÂs warranty for this issue will be extended from 5 years/60,000 miles to 15 years / unlimited miles, whichever comes first, starting from the date the vehicle was first put into service.
CS2310_TSB
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN CUSTOMER SATISFACTION: KIA GENUINE REMOTE START CONTROL MODULE UPGRADE FOR ANTI-THEFT LOGIC COMPATIBILITY (CS2310) - This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 6. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.
WTY033_OWNR
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: OWNER NOTIFICATION - This document is the announcement to the vehicle owners that Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for the low-pressure fuel pump on 2018-2019 MY Sorento vehicles from 5 years / 60,000 miles to 15 years / unlimited miles, whichever comes first, starting from the date the vehicle was first put into service. The low-pressure fuel pump in the subject vehicles may develop a fuel leak over time and after prolonged exposure to extreme high temperatures due to insufficient thickness of the fuel pump port.
WTY033_DP
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: DEALER PRINCIPAL MEMO - This document is the announcement to the dealer principals that Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for the low-pressure fuel pump on 2018-2019 MY Sorento vehicles from 5 years / 60,000 miles to 15 years / unlimited miles, whichever comes first, starting from the date the vehicle was first put into service. The low-pressure fuel pump in the subject vehicles may develop a fuel leak over time and after prolonged exposure to extreme high temperatures due to insufficient thickness of the fuel pump port.
WTY033_DPSM
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: DEALER PRINCIPAL MEMO - This document is the announcement to the dealer principals that Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for the low-pressure fuel pump on 2018-2019 MY Sorento vehicles from 5 years / 60,000 miles to 15 years / unlimited miles, whichever comes first, starting from the date the vehicle was first put into service. The low-pressure fuel pump in the subject vehicles may develop a fuel leak over time and after prolonged exposure to extreme high temperatures due to insufficient thickness of the fuel pump port.
WTY033_QA
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: QUESTION AND ANSWER - This document is a Question and Answer Guide containing the most frequently asked questions regarding the Warranty Extension (WTY033).
WTY033_REIMB
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: REIMBURSEMENT FORM - This document is a Reimbursement Request form that was mailed with the customer letter advising them to submit the form if they had paid for repairs for this same matter prior to the warranty extension program launch.
WTY031_TSB
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: MULTIFUNCTION SWITCH REPAIR - This bulletin provides information associated with the 'Multifunction Switch Warranty Extension Program' (WTY031) to repair the multifunction switch knob on 2016-2018MY Sorento (UMa) vehicles, produced at Kia Georgia from October 27, 2014 through March 7, 2018, which may exhibit an intermittent headlamp flickering. The vehicleâÂÂs warranty for this issue will be extended from 5 years/60,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service.
CS2304_TSB_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.
WTY031_OWNR18
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: OWNER NOTIFICATION - This document is the owner notification advising that Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for the multi-function switch assembly on 2018 MY Sorento vehicles from 5 years / 60,000 miles to 15 years / 150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. The contact points in the multi-function switch in your vehicle may become worn, and it could result in intermittent headlamp flickering.
CS2304_TSB_R2
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.
WTY031_DP
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: DEALER PRINCIPAL MEMO - This document is the announcement to the dealer principals that Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for the multi-function switch assembly on 2016-2018 MY Sorento vehicles from 5 years / 60,000 miles to 15 years / 150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. The contact points in the multi-function switch in the vehicle may become worn, and it could result in intermittent headlamp flickering.
WTY031_DPSM
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: DEALER PARTS AND SERVICE MANAGER MEMO - This document is the announcement to the dealer Parts and Service Managers that Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for the multi-function switch assembly on 2016- 2018 MY Sorento vehicles from 5 years / 60,000 miles to 15 years / 150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. The contact points in the multi-function switch in the vehicle may become worn, and it could result in intermittent headlamp flickering.
WTY031_QA
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: QUESTION AND ANSWER - This document is a Question and Answer Guide containing the most frequently asked questions regarding the Warranty Extension (WTY031).
WTY031_REIMB
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: REIMBURSEMENT FORM - This document is a Reimbursement Request form that was mailed with the customer letter advising them to submit the form if they had paid for repairs for this same matter prior to the warranty extension program launch.
SC260_OWNR
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: OWNER NOTIFICATION - This document is the owner notification advising that Kia is conducting a Voluntary Emissions Service Campaign on certain 2016-2018 MY Kia Sorento vehicles equipped with 2.0L Turbo GDI engines manufactured from October 29, 2014 to November 29, 2017 to improve the emission logic in the Electronic Control Module ('ECM') to ensure compliance with emissions regulations. This condition may cause the vehicle to release air pollutants that exceed Federal and California standards.
SC260_DP
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: DEALER PRINCIPAL MEMO - This document is the announcement to the dealer principals that Kia is conducting a Voluntary Emissions Service Campaign on certain 2016-2018 MY Kia Sorento vehicles equipped with 2.0L Turbo GDI engines manufactured from October 29, 2014 to November 29, 2017 to improve the emission logic in the Electronic Control Module ("'ECM') to ensure compliance with emissions regulations. This condition may cause the vehicle to release air pollutants that exceed Federal and California standards.
SC260_DPSM
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: DEALER PARTS AND SERVICE MANAGER MEMO - This document is the announcement to the dealer Parts and Service Managers that Kia is conducting a Voluntary Emissions Service Campaign on certain 2016-2018 MY Kia Sorento vehicles equipped with 2.0L Turbo GDI engines manufactured from October 29, 2014 to November 29, 2017 to improve the emission logic in the Electronic Control Module ('ECM') to ensure compliance with emissions regulations. This condition may cause the vehicle to release air pollutants that exceed Federal and California standards.
SC260_POC
Service Bulletin/Repair Instructions
SC260_POC: PROOF OF CORRECTION CARD
SC260_QA
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: QUESTION AND ANSWER - This document is the Question and Answer Guide containing the most frequently asked questions regarding the Voluntary Emissions Service Campaign (SC260).
SC260_STKR
Service Bulletin/Repair Instructions
SC260_STKR: VOLUNTARY EMISSIONS SERVICE CAMPAIGN COMPLETION STICKER
SC260_TSB
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: THETA 2.0L T-GDI ECU LOGIC IMPROVEMENT (SC260) - This bulletin provides the procedure to update the emissions-related software logic of the Electronic Control Module (ECM) with an improved version on certain 2016-2018MY Sorento vehicles equipped with Theta 2.0L T-GDI ULEV engines, produced from October 29, 2014 through November 29, 2017. To ensure compliance with emissions regulations, apply the improved logic to the 'Emissions' system using the KDS ECU Upgrade function as described in this bulletin.
CS2304_TSB_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.
CS2304B_OWNR
Service Bulletin/Repair Instructions
CUSTOMER SATISFACTION CAMPAIGN: OWNER NOTIFICATION - This document is the owner notification advising that Kia has developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.
CS2304_TSB
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 20132015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2023MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.
TSB_TRA046_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: TRANSMISSION FLUID APPLICATION GUIDE - This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.
TSB_ENG219_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: MAINTENANCE REMINDER FEATURE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides information on setting the "Service Interval Reminder" feature available on most 2014-2023MY Kia vehicles (refer to model list on page 2). If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance. Refer to TSB ENG241 for 2023MY~ vehicles equipped with the Oil Life Management System (OLMS) feature not included in table on page 2.
WTY026_TSB_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: OIL PRESSURE SWITCH (OPS) REPLACEMENT - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the replacement of the Oil Pressure Switch associated with the 'Warranty Extension Program' (WTY026) on some 2014-2018MY vehicles listed in the table below, for repairs that may be necessary to address an Oil Pressure Switch leak in the eligible vehicles listed below from 10 years/100,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. This warranty extension is to address the Oil Pressure Switch leaking condition at no cost to the customers during this extended warranty period. Follow the procedure outlined in this publication to replace the OPS.
TSB_SST067_R2
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: BEARING CLEARANCE TESTER (BCT) PROCEDURES - This bulletin provides information regarding test procedure of the Bearing Clearance Tester (BCT) Special Service Tool (SST). The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.
TSB_ELE261
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: TRAILER HITCH ACCESSORY FUSE REQUIREMENT - This bulletin provides information regarding the trailer hitch accessory installation on some 2016-2020MY Sorento (UMa) vehicles. Note that the Kia trailer hitch accessory kit requires the use of a 15 Amp fuse rating to be used. The manufacturer of the trailer hitch accessory specifies a fuse size based on development and design of their components including pin terminal, number of circuits, and module design. Always confirm the model of the hitch installed and use the recommended fuse rating required by the manufacturer.
SC234_OWNR
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: OWNER NOTIFICATION - This document is the owner notification advising that Kia is conducting a Voluntary Emissions Service Campaign to install an auxiliary evaporative canister in your vehicle to ensure the evaporative canister is not releasing excessive pollutants into the air.
WTY026_TSB
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN OIL PRESSURE SWITCH (OPS) REPLACEMENT - This bulletin provides information regarding the replacement of the Oil Pressure Switch associated with the 'Warranty Extension Program' (WTY026) on some 2014-2018MY vehicles listed in the table below, for repairs that may be necessary to address an Oil Pressure Switch leak in the eligible vehicles listed below from 10 years/100,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. This warranty extension is to address the Oil Pressure Switch leaking condition at no cost to the customers during this extended warranty period.
SC234_DP
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: DEALER PRINCIPAL MEMO - This document is the announcement to the dealer principals that Kia is conducting a Voluntary Emissions Service Campaign to install an Auxiliary Canister Kit to improve evaporative system performance on certain 2016-2018 MY Kia Sorento vehicles equipped with the 2.4-liter GDI engine and manufactured from November 4, 2014 through March 7, 2018.
SC234_DPSM
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: DEALER PARTS AND SERVICE MANAGER MEMO - This document is the announcement to the dealer Parts and Service Managers that Kia is conducting a Voluntary Emissions Service Campaign to install an Auxiliary Canister Kit to improve evaporative system performance on certain 2016-2018 MY Kia Sorento vehicles equipped with the 2.4-liter GDI engine and manufactured from November 4, 2014 through March 7, 2018.
SC234_POC
Service Bulletin/Repair Instructions
SC234_POC: PROOF OF CORRECTION CARD
SC234_QA
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: QUESTION AND ANSWER - This document is the Question and Answer Guide containing the most frequently asked questions regarding the Voluntary Emissions Service Campaign (SC234).
SC234_STKR
Service Bulletin/Repair Instructions
SC234_STKR: VOLUNTARY EMISSIONS SERVICE CAMPAIGN COMPLETION STICKER
SC234_TSB
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: 2.4L GDI AUXILIARY CANISTER KIT INSTALLATION (SC234) - This bulletin provides the procedure for the installation of an add-on auxiliary canister on some 2016-2018MY Sorento (UMa) vehicles equipped with the 2.4L GDI engine, produced from November 4, 2014 through March 7, 2018. This is to improve the evaporative system and ensure compliance with Federal and California emission regulation standards.
SC201_TSB_R2
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN: 2.0L T-GDI AUXILIARY CANISTER KIT INSTALLATION (SC201) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure for the installation of an add-on auxiliary canister on some 2016-2018MY Sorento (UMa) vehicles equipped with the 2.0L T-GDI engine, produced from October 29, 2014 through November 29, 2017. This is to improve evaporative system and ensure compliance with Federal and California emission regulation standards.
PS720
Service Bulletin/Repair Instructions
PITSTOP: INJECTOR HARNESS ROUTING FOR PI1802Y/Z AND PI1803Y/Z ENGINE REPLACEMENTS - This bulletin provides information to address a no-start or hard start with poor running condition after engine replacement under PI1802Y/Z or PI1803Y/Z. Some replacement long blocks may come with pre-installed fuel rail, injectors, and injector wiring harness. If the condition is present, it is possible that the injector harness was not installed correctly. The connections may be swapped from cylinder No. 1 and cylinder No. 4, and from cylinder No. 2 and cylinder No. 3.
WTY026_OWNR_XM
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: OWNER NOTIFICATION - This document is the owner notification that Kia is extending the New Vehicle Limited Warranty coverage for repairs that may be necessary to address an Oil Pressure Switch leak in 2014-2018 MY Sorento vehicles equipped with 3.3L GDI Engine from 5 years/60,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service.
WTY026_REIMB_XM
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: REIMBURSEMENT FORM - This document is a Reimbursement Request form for 14-18 MY Sorento customers which was mailed with the customer letter advising them to submit the form if they had paid for repairs for this same matter prior to the warranty extension program launch.
WTY026_DP
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: DEALER PRINCIPAL MEMO - This document is the announcement to the dealer principals of the warranty extension program for WTY026. Kia is extending the New Vehicle Limited Warranty coverage for the repairs related to the Oil Pressure Switch leaking for eligible vehicles from 5 years/60,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service.
WTY026_DPSM
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: DEALER PARTS AND SERVICE MANAGER MEMO - This document is the announcement to the dealer Parts and Service Managers of the warranty extension program for WTY026. Kia is extending the New Vehicle Limited Warranty coverage for the repairs related to the Oil Pressure Switch leaking for eligible vehicles from 5 years/60,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service.
WTY026_QA
Service Bulletin/Repair Instructions
WARRANTY EXTENSION: QUESTION AND ANSWER - This document is the Question and Answer Guide containing the most frequently asked questions regarding the warranty extension (WTY026).
PS613_R1
Service Bulletin/Repair Instructions
PITSTOP: INSTRUMENT CLUSTER REPLACEMENT AND MILEAGE SETTING WITH KDS - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This pitstop provides the KDS service procedure for mileage setting on the models listed below with newly replaced instrument clusters. Certain models allow for mileage setting with the KDS, which prevents the need to send out the instrument cluster to a 3rd party for mileage adjustment (refer to PS264). After a new cluster is installed, cluster (variant) coding may also need to be conducted using the KDS. Make sure the KDS software is also updated to the latest version. Mileage setting should be performed by using the KDS only, as described in this bulletin.
TSB_ENG222_R6
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA/KAPPA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.
TSB_ENG222_R5
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA/KAPPA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.
PI1802YZ_TSB_R6
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
TSB_ENG222_R4
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA/KAPPA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.
TSB_ELE248
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: OUTSIDE REAR COMBINATION LAMP HARNESS REPLACEMENT - This bulletin provides the procedure to replace both outside rear combination lamp harnesses on some 2018-2019MY Sorento (UMA) vehicles, produced from January 2, 2018, through September 30, 2018, which may exhibit an intermittent inoperative brake light with the possibility of a "Check brake light" warning on the instrument cluster display.
PI1802YZ_TSB_R5
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
TSB_SST067_R1
Service Bulletin/Repair Instructions
This bulletin provides information regarding test procedure of the Bearing Clearance Tester (BCT) Special Service Tool (SST). The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.
TSB_CHA111
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: REPLACEMENT OF MOBIS C-MDPS SMALL BEARING - This bulletin provides the procedure to replace the small bearing of the Column Motor Driven Power Steering (C-MDPS) unit on the vehicles listed below, which may exhibit an abnormal noise when steering left and right. This may be caused by foreign substances in the MDPS worm shaft small bearing. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Small Bearing and does not affect the steering effort.
TSB_CHA084_R8
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.
TSB_BOD055_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: INFORMATION FOR HEADLAMP CONDENSATION AND MOISTURE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.
TSB_ENG222_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA/KAPPA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.
TSB_CHA106
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF THE DUAL PINION MOTOR DRIVER POWER STEERING SYSTEM - This bulletin provides information regarding the availability of partial repair (depending on faulty components) of the Dual Pinion Motor Driven Power Steering (DP-MDPS) system on some 2016-2021MY~ Kia vehicles (refer to the table below) in order to enhance customer satisfaction by promoting a cost-effective repair/replacement of a faulty related part, instead of replacement of the complete DP-MDPS assembly.
PS704
Service Bulletin/Repair Instructions
PITSTOP: FRONT RADAR SENSOR MOUNTING INSPECTION (PS704) - This pitstop provides information regarding front radar sensor alignment on 2014MY and later vehicles that may exhibit a warning light ON related to radar sensor alignment errors in the Forward Collision-Avoidance Assist (FCA)/Smart Cruise Control (SCC) system.
SC201_TSB_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: 2.0L T-GDI AUXILIARY CANISTER KIT INSTALLATION (SC201) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure for the installation of an add-on auxiliary canister on some 2016-2018MY Sorento (UMa) vehicles equipped with the 2.0L T-GDI engine, produced from October 29, 2014 through November 29, 2017. This is to improve evaporative system and ensure compliance with Federal and California emission regulation standards.
SC201_TSB
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: 2.0L T-GDI AUXILIARY CANISTER KIT INSTALLATION (SC201) - This bulletin provides the procedure for the installation of an add-on auxiliary canister on some 2016-2018MY Sorento (UMa) vehicles equipped with the 2.0L T-GDI engine, produced from October 29, 2014 through November 29, 2017. This is to improve evaporative system and ensure compliance with Federal and California emission regulation standards.
SC201_OWNR
Service Bulletin/Repair Instructions
SC201_OWNR: OWNER NOTIFICATION - This document is the notification to customers that Kia Motors America, Inc. is conducting a Voluntary Emissions Service Campaign to install an Auxiliary Canister Kit to improve evaporative system performance on certain 2016-2018 MY Kia Sorento vehicles equipped with the 2.0-liter Turbo-GDI engine and manufactured from October 29, 2014 through November 29, 2017.
SC201_DP
Service Bulletin/Repair Instructions
SC201_DP: DEALER PRINCIPAL MEMO - This document is the announcement to the dealer principals that Kia Motors America, Inc. is conducting a Voluntary Emissions Service Campaign to install an Auxiliary Canister Kit to improve evaporative system performance on certain 2016-2018 MY Kia Sorento vehicles equipped with the 2.0-liter Turbo-GDI engine and manufactured from October 29, 2014 through November 29, 2017.
SC201_DPSM
Service Bulletin/Repair Instructions
SC201_DPSM: DEALER PARTS AND SERVICE MANAGER MEMO - This document is the announcement to the dealer Parts and Service Managers that Kia Motors America, Inc. is conducting a Voluntary Emissions Service Campaign to install an Auxiliary Canister Kit to improve evaporative system performance on certain 2016-2018 MY Kia Sorento vehicles equipped with the 2.0-liter Turbo-GDI engine and manufactured from October 29, 2014 through November 29, 2017.
SC201_POC
Service Bulletin/Repair Instructions
SC201_POC: PROOF OF CORRECTION CARD
SC201_QA
Service Bulletin/Repair Instructions
SC201_QA: QUESTION AND ANSWER - This document is the Question and Answer guide containing the most frequently asked questions regarding the Voluntary Emissions Service Campaign (SC201).
SC201_STKR
Service Bulletin/Repair Instructions
SC201_STKR: VOLUNTARY EMISSIONS SERVICE CAMPAIGN COMPLETION STICKER
TSB_CHA084_R7
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
TSB_ENG222_R2
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.
TSB_ENG222_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.
TSB_CHA084_R6
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
PI1802YZ_TSB_R4
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled âÂÂKnock Sensor Detection System - ECU Logic Improvementâ equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
TSB_CHA084_R5
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
PS663
Service Bulletin/Repair Instructions
PITSTOP: MFC, CONCERNS FOR DISABLED OPERATION - This Pitstop provides information regarding concerns with disabled operation of Multi-Function Camera (MFC) on some Kia vehicles. When normal operation is not possible due to certain outside environment conditions (such as sunlight glare, heavy rain, sunlight, snow, fog and/or substance/debris) causing a temporary concern. This stops operation causing Warning Lamp ON and/or Pop-up Message displayed on the cluster. This is a normal operation of the ADAS and once environment conditions improve and/or substance/debris are removed, the system will clear itself and operate normally.
PS675
Service Bulletin/Repair Instructions
PITSTOP - BRAKE CALIPER LEAK INSPECTION - This PITSTOP provides information related to a brake caliper fluid/oil substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.
TSB_ELE205
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: REAR VIEW CAMERA REPLACEMENT - This bulletin provides the procedure to replace the rear view camera on some 2016-2020MY Sorento (UMa) produced from SOP through July 9, 2020, due to distortion and/or blue screen caused by moisture intrusion into the camera assembly.
PI1802_TSB_R12
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT - TSB_PI1802_R2 - Knock Sensor Detection System - ECU Logic Improvement - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
TSB_ENG219
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: MAINTENANCE REMINDER FEATURE - This bulletin provides information on setting the "Service Interval Reminder" feature available on most Kia vehicles. If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance.
PI1802YZ_TSB_R3
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN - ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z_Rev3) - This bulletin has been revised to include additional information. - This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement".
PI1802YZ_TSB_R2
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN - ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z_Rev2) - This bulletin has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement".
PI1802_TSB_R11
Service Bulletin/Repair Instructions
TSB: PRODUCT IMPROVEMENT CAMPAIGN : KNOCK SENSOR DETECTION SYSTEM (KSDS) LOGIC IMPROVEMENT (PI1802_R11) - This bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
PS608_R1
Service Bulletin/Repair Instructions
PITSTOP: UPDATED SPARK PLUG FOR 2.0T THETA-II - This bulletin has been revised to include additional information. This Pitstop provides information regarding the updated spark plug for vehicles listed below, equipped with 2.0T Theta-II engines, which may not yet be available in the Electronic Parts Catalog (EPC). If not available, the updated spark plug must be ordered manually. This updated spark plug has been improved with the thread shoulder lengthened to enhance protection of the insulator from combustion heat.
TSB_ENG205_C
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: SERVICE ACTION: WIRING SIGNAL INTERFERENCE CHECK & ENGINE NOISE INSPECTION (SA379) - CLOSED - SUPERSEDED BY PI1802YZ/1803YZ.
TSB_CHA091_R2
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: STEERING GEAR YOKE PLUG AND ASSEMBLY REPLACEMENT - This bulletin has been revised to include additional information. This bulletin provides the procedure to replace the steering gear box yoke plug and assembly on some models listed below, which may exhibit a ticking noise while turning the steering wheel with the vehicle stopped. This condition is caused by a worn lining on the steering gear box yoke assembly.
TSB_TRA046_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: - TRANSMISSION FLUID APPLICATION GUIDE - This bulletin has been revised to include additional information. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.
PI1802YZ_TSB_R1
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
PI1802WX_TSB_R7C
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: TSB_R7 - ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802W/X) - CLOSED - SUPERSEDED BY PI1802Y/Z.
PI1802YZ_TSB
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: TSB - ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802Y/Z) - This bulletin has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled Knock Sensor Detection System - ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
PI1802_TSB_R10
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: TSB - REV 10 - KNOCK SENSOR DETECTION SYSTEM - ECU LOGIC IMPROVEMENT (PI1802) - This bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
PI1802_TSB_R9
Service Bulletin/Repair Instructions
TSB - PRODUCT IMPROVEMENT CAMPAIGN - KNOCK SENSOR DETECTION SYSTEM - ECU LOGIC IMPROVEMENT (PI1802) Rev.9 - This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
PI1802WX_TSB_R7
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802W/X) - This bulletin has been revised to include additional information.This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC), P1326.
TSB_CHA091_R1
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: STEERING GEAR YOKE PLUG AND ASSEMBLY REPLACEMENT - This bulletin has been revised to include additional information. This bulletin provides the procedure to replace the steering gear box yoke plug and assembly on some models listed below, which may exhibit a ticking noise while turning the steering wheel with the vehicle stopped. This condition is caused by a worn lining on the steering gear box yoke assembly. Follow the procedure outlined in this bulletin to replace the steering gear box yoke plug and assembly with updated parts.
TSBCHA084_R4
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.
TSBTRA086
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN - PARTIAL REPAIR OF 4WD COUPLING - This bulletin provides the procedure information regarding the partial repair of the Four Wheel Drive (4WD) Coupling Assembly, Pressure Sensor, Actuator Motor or 4WD harness on some 2011-2020 Sportage (SL, QL) and 2013-2020MY Sorento (XMa, UMa) 4WD vehicles for a concern regarding: ï· Oil leakage from the 4WD coupling assembly ï· 4WD Malfunction and MIL lamp ON with DTCs ï· Abnormal noise or vibration while driving
PI1802WX_TSB_R6
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN PI1802W/X (Rev 6) - PRODUCT IMPROVEMENT CAMPAIGN - ENGINE REPLACEMENT INSTRUCTIONS - This bulletin has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled 'Â"Knock Sensor Detection System - ECU Logic Improvement"ÂÂ. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("ÂÂDTC"ÂÂ), P1326.
PI1802_TSB_R8
Service Bulletin/Repair Instructions
TSB - Product Improvement Campaign: KNOCK SENSOR DETECTION SYSTEM - ECU LOGIC IMPROVEMENT (PI1802) - This bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
TSBCHA084_R3
Service Bulletin/Repair Instructions
TECHNICAL SERVICE BULLETIN TSB084_R3: PARTIAL REPAIR OF C-MDPS MOTOR, ECU AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
PI1802_TSB_R7
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN - KNOCK SENSOR DETECTION SYSTEM - ECU LOGIC IMPROVEMENT (PI1802) - This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage. The KSDS detects vibrations indicating the onset of excessive connecting rod bearing wear. It is designed to alert the driver at an early stage of bearing wear before the occurrence of severe engine damage, including engine failure. If vibrations caused by bearing wear start to occur, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Limp Home Mode. This will reduce further damage to the engine and ensure that the vehicle occupants are not exposed to the risk of a more severe engine failure. At that time, Diagnostic Trouble Code (âÂÂDTCâÂÂ) P1326, specific to the KSDS, will be recorded in the ECU. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed. Also, engine RPMs will be limited to approximately 1800-2000 RPM.
TSBENG178_R3
Service Bulletin/Repair Instructions
TSB: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC18) - This bulletin has been revised to include additional information. This bulletin provides information related to extracting âÂÂin use performance trackingâ emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California.
TSBCHA060_R5
Service Bulletin/Repair Instructions
TSB: ECU UPGRADE - STEERING LOGIC IMPROVEMENT - This bulletin has been revised to include additional information. This bulletin provides information related to the MDPS ECU software upgrade for some 2012-2014MY Optima (QF), produced from August 2, 2010 through July 27, 2014, and 2016-2018MY Sorento (UMa) vehicles, produced from October 27, 2014 through August 22, 2017, which may experience a notchy feel in the steering wheel. To correct this condition, the vehicle should be evaluated using the MDPS Effort Measurement Software detailed in the repair procedure starting on page 2 to determine whether an improved steering logic should be installed in the MDPS ECU, or if the Steering Column and Housing Assembly replacement is required.
TSBCHA084_R2
Service Bulletin/Repair Instructions
TSB: REPLACEMENT OF C-MDPS MOTOR, ECU AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on the Kia models listed on the chart below with a column mounted C-MDPS unit.
PS613
Service Bulletin/Repair Instructions
PITSTOP: INSTRUMENT CLUSTER REPLACEMENT, MILEAGE SETTING WITH KDS - This publication provides the KDS service procedure for mileage setting on the listed vehicles with newly replaced instrument clusters.
PI1802_OWNR2_SOR
Service Bulletin/Repair Instructions
PI1802_OWNR2_SOR: Kia Motors America, Inc. is conducting an important Product Improvement Campaign to perform a software update on 2015 MY Sorento vehicles equipped with 2.4L GDI engines and all 2016-2018 MY Sorento vehicles equipped with 2.4L Gasoline Direct Injection ("ÂÂGDI"ÂÂ) and 2.0L Turbocharged GDI ("ÂÂT-GDI"ÂÂ) engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (ECU).
PS600
Service Bulletin/Repair Instructions
PITSTOP: OUTSIDE MIRROR GLASS CONTROL INOPERATIVE - This Pitstop provides information on the repair procedure for an inoperative mirror glass on the outside door mirrors for 2016-2019MY Optima (JFa) and Sorento (UMa) vehicles.
PS608
Service Bulletin/Repair Instructions
PITSTOP: UPDATED SPARK PLUG FOR 2.0T THETA-II - This Pitstop provides information regarding the updated spark plug for 2017-2018MY Sportage (QL) 2.0T and 2016-2018MY Sorento (UMa) 2.0T vehicles, which may not yet be available in the Electronic Parts Catalog (EPC). If not available, the updated spark plug must be ordered manually.
TSBENG178_R2
Service Bulletin/Repair Instructions
TSB: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC18) - This bulletin provides information related to extracting "in use performance tracking" emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California. The California Air Resources Board (CARB) requires the emissions data from vehicles with a minimum of 3,000 accumulated miles without reprogramming or resetting.
PI1802WX_TSB_R5
Service Bulletin/Repair Instructions
TSB: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802W/X) - This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.
TSBENG205_R1
Service Bulletin/Repair Instructions
TSB: SERVICE ACTION: WIRING SIGNAL INTERFERENCE CHECK & ENGINE NOISE INSPECTION (SA379) - This bulletin provides information related to an expanded diagnostic test that is now required on a number of vehicles previously diagnosed with Diagnostic Trouble Code ("DTC") P1326. Using the procedures published in TSB PI1802W/X and PI1803W/X, the subject vehicles were diagnosed and determined to require an engine replacement and are currently being held at dealers pending repair. As a result of additional field data collection and analysis, the initial diagnosis method has been updated to improve test result accuracy. Prior to performing an engine replacement on any of the VINs affected by this Service Action, the engine condition needs to be re-assessed utilizing an updated/expanded diagnostic process.
TSBENG205
Service Bulletin/Repair Instructions
TSB: SERVICE ACTION: WIRING SIGNAL INTERFERENCE CHECK & ENGINE NOISE INSPECTION (SA379) - This bulletin provides information related to an expanded diagnostic test that is now required on a number of vehicles previously diagnosed with Diagnostic Trouble Code ("DTC") P1326. Using the procedures published in TSB PI1802W/X and PI1803W/X, the subject vehicles were diagnosed and determined to require an engine replacement and are currently being held at dealers pending repair. As a result of additional field data collection and analysis, the initial diagnosis method has been updated to improve test result accuracy. Prior to performing an engine replacement on any of the VINs affected by this Service Action, the engine condition needs to be re-assessed utilizing an updated/expanded diagnostic process.
PI1802WX_TSB_R4
Service Bulletin/Repair Instructions
TSB: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802W/X) - This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.
PS590
Service Bulletin/Repair Instructions
PITSTOP: BLOCKED WINDSHIELD WASHER NOZZLES ON VEHICLES EQUIPPED WITH WASHER HEATERS - This Pitstop provides information regarding blocked windshield wiper nozzles on some 2016MY~ Sorento (UMa) and 2017MY~ Sportage (QL) vehicles equipped with windshield washer heaters (A). Mixing tap water (?) and concentrated windshield washer fluid can cause corrosion of the heater element due to the mineral content of tap water.
TSBCHA060_R4
Service Bulletin/Repair Instructions
TSB: ECU UPGRADE ? STEERING LOGIC IMPROVEMENT -This bulletin has been revised to include additional information. This bulletin provides information related to the MDPS ECU software upgrade for some 2011-2014MY Optima (QF), produced from August 2, 2010 through July 27, 2014, and 2016-2018MY Sorento (UMa) vehicles, produced from October 27, 2014 through August 22, 2017, which may experience a notchy feel in the steering wheel.
VPI1802WX_TSB_R3
Service Bulletin/Repair Instructions
VEHICLE PRODUCT IMPROVEMENT: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802W/X)- This bulletin has been revised to include additional information This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326..
TSBELE165
Service Bulletin/Repair Instructions
TSB: DRIVER?S DOOR MODULE LOGIC IMPROVEMENT - This bulletin provides the procedure to improve the logic of the Driver?s Door Module (DDM) on some 2017-2018MY Sorento (UMa) vehicles, produced from April 4, 2016 through August 23, 2017, which may experience the absence of the Auto Door Lock/Unlock option select in the instrument cluster.
VPI1802_TSB_R6
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN:KNOCK SENSOR DETECTION SYSTEM - ECU LOGIC IMPROVEMENT (PI1802) - This bulletin has been revised to include additional information.This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
VPI1802WX_TSB_R2
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI1802W/X) - This bulletin has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 5, 12/20/2018) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326.
TSBCHA060_R3
Service Bulletin/Repair Instructions
TSB: ECU UPGRADE ? STEERING LOGIC IMPROVEMENT - This bulletin has been revised to include additional information. This bulletin provides information related to the MDPS ECU software upgrade for some 2011-2014MY Optima (QF), produced from August 2, 2010 through July 27, 2014, and 2016-2018MY Sorento (UMa) vehicles, produced from October 27, 2014 through August 22, 2017, which may experience a notchy feel in the steering wheel.
TSBENG083_R1
Service Bulletin/Repair Instructions
TSB: SPECIAL SERVICE INFORMATION & SPECIFICATIONS FOR GDI HIGH PRESSURE FUEL SYSTEM - This bulletin has been revised to include additional information. This bulletin provides information relating to all Kia vehicles equipped with Gasoline Direct Injection (GDI) engines. In these engines highly pressurized gasoline is injected via a common fuel rail and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional Multi-Point Fuel Injection (MPI) engine, the gasoline is injected into the intake port of each cylinder at a relatively low pressure. Due to high fuel pressure in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specifications for the GDI fuel system components.
TSBCHA084_R1
Service Bulletin/Repair Instructions
TSB: REPLACEMENT OF C-MDPS MOTOR AND/OR ECU - This bulletin has been revised to include additional information. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor and/or Electronic Control Unit (ECU) on the listed Kia models with a column mounted C-MDPS unit.
TSBCHA060_R2
Service Bulletin/Repair Instructions
TSB - ECU UPGRADE ? STEERING LOGIC IMPROVEMENT -This bulletin has been revised to include additional information. This bulletin provides information related to the MDPS ECU software upgrade for some 2011-2014MY Optima (QF), produced from August 2, 2010 through July 27, 2014, and 2016-2018MY Sorento (UMa) vehicles, produced from October 27, 2014 through August 22, 2017, which may experience a notchy feel in the steering wheel. To correct this condition, the vehicle should be evaluated using the MDPS Effort Measurement Software detailed in the repair procedure starting on page 2 to determine whether an improved steering logic should be installed in the MDPS ECU, or if an MDPS column replacement is required. To determine whether the updated MDPS ECU reflash applies to a vehicle you are working on, or whether it has already been performed, verify ROM ID using the tables in this TSB.
VPI1802_TSB_R5
Service Bulletin/Repair Instructions
PRODUCT IMPROVEMENT CAMPAIGN - This bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
VPI1802_OWNER_SO
Service Bulletin/Repair Instructions
Dear Kia Sorento Owner: Kia Motors America, Inc. is conducting an important Product Improvement Campaign to perform a software update on all 2016-2018 MY Sorento vehicles equipped with 2.4L Gasoline Direct Injection (?GDI?) and 2.0L Turbocharged GDI (?T-GDI?) engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (ECU).
TSBCHA084
Service Bulletin/Repair Instructions
TSB: REPLACEMENT OF C-MDPS MOTOR AND/OR ECU - This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor and/or Electronic Control Unit (ECU) on the listed Kia models with a column mounted C-MDPS unit. Follow the procedure outlined in this bulletin.
VPI1802_QA
Service Bulletin/Repair Instructions
Q & A - This document is the Q & A for the new Product Improvement Campaign to provide information regarding a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.
VPI1802_DP
Service Bulletin/Repair Instructions
DEALER PRINCIPAL NOTICE - This notice advised the dealer principal of the new Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.
VPI1802_DSM
Service Bulletin/Repair Instructions
DEALER SERVICE MANAGER NOTICE - This notice advised the dealer service manager of the new Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.
TSBENG177C_R4
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: 2.4L ENGINE STAR LOGIC IMPROVEMENT (SA316C) - This bulletin has been revised to include additional information.This bulletin provides the procedure to improve the logic of the Engine Control Unit (ECU) on some 2018MY Sorento (UMa) 2.4L vehicles, produced from September 18, 2017 through December 6, 2017, which may experience a very slight surging sensation with the cruise control activated and/or extended crank.
PS564
Service Bulletin/Repair Instructions
PITSTOP - CLOCK CONCERNS ON UVO eSERVICES (UVO 3.0) - This Pitstop contains information regarding possible concerns with the clock on UVO eServices (UVO 3.0) head units installed on 2017-2018MY vehicles.
TSBENG178_R1
Service Bulletin/Repair Instructions
TSB - DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC18) - This bulletin has been revised to include additional information. This bulletin provides information related to extracting ?in use performance tracking? emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California.
TSBENG187
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: SORENTO (UMa) 3.3L - PRE-DELIVERY INSPECTION (SA345) -= This bulletin provides the procedure to inspect the engine assembly on some 2018MY Sorento (UMa) 3.3L AWD (262 vehicles affected), produced from January 29, 2018 through February 20, 2018, which may exhibit abnormal engine noise.
PS551
Service Bulletin/Repair Instructions
PITSTOP - RATTLE NOISE FROM REAR OF THE VEHICLE (PS551) - This Pitstop contains information regarding a rattle type noise heard from the rear of the vehicle when closing a door or trunk on some 2016MY-2018MY vehicles.
TSBENG177B_R1CLO
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: 2.4L SHIFT QUALITY & WAKE-UP LOGIC IMPROVEMENT (SA316B) - This bulletin has been CLOSED and superceded by TSB-ENG177C R3.
TSBENG177C_R3
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: 2.4L ENGINE START LOGIC IMPROVEMENT (SA316C) - This bulletin has been revised to include additional information. This bulletin provides the procedure to improve the logic of the Engine Control Unit (ECU) on some 2018MY Sorento (UMa) 2.4L vehicles, produced from September 20, 2017 through December 6, 2017, which may experience a very slight surging sensation with the cruise control activated and/or extended crank.
PS539
Service Bulletin/Repair Instructions
PITSTOP - ENGINE COMPONENT RE-USE GUIDELINES - In general, parts and components removed during engine repairs should be considered serviceable, and should be thoroughly cleaned and transferred to the new engine.
PS547
Service Bulletin/Repair Instructions
PITSTOP - EPS RECOGNTION / SAS CALIBRATION OF C-MDPS STEERING COLUMN ASSEMBLY - This Pitstop provides information regarding the Electronic Power Steering (EPS), Steering Angle Sensor (SAS) calibration and EPS type recognition after replacement of the Column-Mounted, Motor Driven Power Steering (C-MDPS) assembly on 2016-2018MY Sorento (UMa) vehicles.
TSBTRA047_R2
Service Bulletin/Repair Instructions
TSB - DRIVESHAFT SERVICEABILITY - This bulletin has been revised most recently to include additional information. This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.
PS542
Service Bulletin/Repair Instructions
PITSTOP - LDWS/MFC Variant Coding - This Pitstop provides information regarding the correct ?Variant Coding? settings for the Multi-Function Camera (MFC) on some 2017-2018MY Sorento (UMa) vehicles.
PS543
Service Bulletin/Repair Instructions
PITSTOP - AEB VARIANT CODING - This Pitstop provides information regarding the correct ?Variant Coding? settings for the Autonomous Emergency Braking (AEB) on some 2017-2018MY Sorento (UMa) vehicles.
PS541
Service Bulletin/Repair Instructions
PITSTOP - INOPERATIVE SHIFT LOCK RELEASE AND/OR IGNITION IN ACCESSORY MODE - This pitstop provides the procedure to inspect the Key Interlock Switch contact on some 2016-2018MY Sorento (UMa) vehicles experience one of the following:1. An inoperative shift lock release; 2. No crank; 3. Inoperative key release (on key-start equipped vehicles); 4. Ignition stuck in accessory mode accompanied by a ?Shift to Park? message (on smart key equipped vehicles).
TSBENG177B_R1
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: 2.4L SHIFT QUALITY & WAKE-UP LOGIC IMPROVEMENT (SA316B) - This bulletin provides the procedure to improve the logic of the Electronic Control Unit (ECU) and Transmission Control Unit (TCU) on some 2018MY Optima (JFa) 2.4L, produced from April 18, 2017 through September 7, 2017, and some 2017MY Sorento (UMa) 2.4L vehicles, produced from March 31, 2017 through December 6, 2017, which may experience an extended crank and/or a shift quality concern, such as a hard downshift, upshift, and/or shift delay.
TSBENG177C_R2
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: 2.4L ENGINE START LOGIC IMPROVEMENT (SA316C) - This bulletin provides the procedure to improve the logic of the Engine Control Unit (ECU) on some 2018MY Sorento (UMa) 2.4L vehicles, produced from March 31, 2017 through November 20, 2017, which may experience a very slight surging sensation with the cruise control activated.
TSBENG178
Service Bulletin/Repair Instructions
TSB - DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC18) - This bulletin provides information related to extracting ?in use performance tracking? emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California.
TSBENG177CR1
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: 2.4L ENGINE START LOGIC IMPROVEMENT (SA316C) REV 1 - This bulletin provides the procedure to improve the logic of the Engine Control Unit (ECU) on some 2018MY Sorento (UMa) 2.4L vehicles, produced from March 31, 2017 through November 16, 2017, which may experience a very slight surging sensation with the cruise control activated.
PS531
Service Bulletin/Repair Instructions
PITSTOP - KEY FOB AND BATTERY VIN LABELS - To assist in improving product quality and warranty claims, key fobs/smart keys and the vehicle battery now have labels (A) containing the Vehicle Identification Number (VIN). These labels have been applied beginning with October 21, 2017 production for Optima (JFa) and Sorento (UMa) from the Kia Motors Manufacturing Georgia (KMMG) plant.
TSBENG177B
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: 2.4L SHIFT QUALITY & WAKE-UP LOGIC IMPROVEMENT (SA316B) - This bulletin provides the procedure to improve the logic of the Electronic Control Unit (ECU) and Transmission Control Unit (TCU) on some 2018MY Optima (JFa) 2.4L, produced from April 18, 2017 through September 7, 2017, and some 2018MY Sorento (UMa) 2.4L vehicles, produced from March 31, 2017 through October 19, 2017, which may experience an extended crank and/or a shift quality concern, such as a hard downshift, upshift, and/or shift delay.
TSBENG177C
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: 2.4L ENGINE START LOGIC IMPROVEMENT (SA316C) - This bulletin provides the procedure to improve the logic of the Engine Control Unit (ECU) on some 2018MY Sorento (UMa) 2.4L vehicles, produced from March 31, 2017 through November 16, 2017, which may experience a very slight surging sensation with the cruise control activated.
TSBTRA071AR1
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: 2.0t & 3.3l SHIFT QUALITY LOGIC IMPROVEMENT (SA315A) - This bulletin provides the procedure to improve the logic of the Transmission Control Unit (TCU) on some 2018MY Optima (JFa) 2.0T, produced from April 19, 2017 through July 10, 2017, and some 2018MY Sorento (UMa) 2.0T and 3.3L vehicles, produced from March 23, 2017 through September 18, 2017, which may experience a shift quality concern, such as a hard downshift, upshift, and/or shift delay.
TSBTRA071
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: 2.0T & 3.3L SHIFT QUALITY LOGIC IMPROVEMENT (SA315) - CLOSED - This bulletin provides the procedure to improve the logic of the Transmission Control Unit (TCU) on some 2018MY Optima (JFa) 2.0T, produced from April 19, 2017 through July 10, 2017, and some 2018MY Sorento (UMa) 2.0T and 3.3L vehicles, produced from March 31, 2017 through July 25, 2017, which may experience a shift quality concern, such as a hard downshift, upshift, and/or shift delay.
TSBTRA071A
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: SHIFT QUALITY LOGIC IMPROVEMENT (SA315A) - This bulletin provides the procedure to improve the logic of the Transmission Control Unit (TCU) on some 2018MY Optima (JFa) 2.0T, produced from April 19, 2017 through July 10, 2017, and some 2018MY Sorento (UMa) 3.3L vehicles, produced from March 31, 2017 through July 25, 2017, which may experience a shift quality concern, such as a hard downshift, upshift, and/or shift delay.
TSBENG177
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: 2.4L SHIFT QUALITY & WAKE-UP LOGIC IMPROVEMENT (SA316) - CLOSED - This bulletin provides the procedure to improve the logic of the Electronic Control Unit (ECU) and Transmission Control Unit (TCU) on some 2018MY Optima (JFa) 2.4L, produced from April 18, 2017 through September 7, 2017, and some 2018MY Sorento (UMa) 2.4L vehicles, produced from March 31, 2017 through October 19, 2017, which may experience an extended crank and/or a shift quality concern, such as a hard downshift, upshift, and/or shift delay.
TSBBOD176
Service Bulletin/Repair Instructions
TSB - SERVICE ACTION: SORENTO (UMA) HEADREST HANG TAG REPLACEMENT (SA314) - This bulletin provides the procedure to replace the front headrest hang tag on some 2018MY Sorento (UMa) vehicles, produced from March 31, 2017 through September 22, 2017, which may have the incorrect hang tag displaying information regarding ?Dual Clutch Transmission? (DCT).