Vehicle report

2020 MAZDA CX-9

Compare every MAZDA CX-9 yearNHTSA and EPA records

Service bulletins

319 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

SA-041-26

Service Bulletin/Repair Instructions

This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.

09-019-26

Service Bulletin/Repair Instructions

This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 09-012/21 12/13/21, 06/10/21 and 04/27/21 DESCRIPTION Some customers may experience all of following symptoms: The door lock/unlock operation will not work using the remote transmitter button. 1. The door lock/unlock operation will not work using the door lock/release touch sensor. 2. The engine will not start using the ignition switch. 3. The transmitter operates by itself. 4. The key battery drains faster than usual. 5. Symptoms 1-3: This may be caused when excess load is applied to the remote transmitter, deforming the electrical terminals and creating poor contact with the battery. To eliminate this concern, the structure in the remote transmitter has been modified to reduce the deformation of the electrical terminals. Symptom 4-5: This may be caused when excessive load is applied to the remote transmitter, creating a gap around the gasket where moisture enters and corrodes the circuit board which in turn drains the key battery faster than usual. To eliminate this concern, the thickness of the case wall on the gasket mounting surface has been increased and the bonding strength of the components has been improved to prevent deformation. REPAIR PROCEDURE • If the battery is bad or installed incorrectly, replace the battery and/or install it correctly. • If the remote power saving function is off and the battery is good and installed correctly, replace the defective remote transmitter with a modified one according to the instructions on MGSS (IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING). NOTE: DO NOT replace other remote transmitter(s) for the vehicle if they not experiencing an issue.

SA-027-26a

Service Bulletin/Repair Instructions

This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-027/26 04/16/26 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. REPAIR PROCEDURE 1. Perform appropriate repair to vehicle. If needed, use the Battery Diagnostics of the DCA-8000 to test the charging and starting systems by following the on-screen instructions for entering the appropriate information. Refer to the Mazda DCA-8000 Instruction Manual for more information.

01-008-26

Service Bulletin/Repair Instructions

This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 01-008/23 06/05/23 Some vehicles may exhibit rattling noises from the engine compartment and oil leakage from the drive belt auto tensioner. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed. REPAIR PROCEDURE If the tensioner is found to be "No Good" after completing the Drive Belt Auto Tensioner Inspection, replace it with a modified part according to the instructions on MGSS online:

SA-031-26

Service Bulletin/Repair Instructions

DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the B􀀀pillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.

SA-029-26

Service Bulletin/Repair Instructions

This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.).

SA-026-26

Service Bulletin/Repair Instructions

This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.

SA-027-26

Service Bulletin/Repair Instructions

This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-007/25 10/22/25, 06/02/25 and 02/03/25 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery’s Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries. TEST PROCEDURE 1. Connect the charger clamps to the appropriate battery posts.

SA-014-26

Service Bulletin/Repair Instructions

This Service Alert supersedes the previously issued SA(s) and TSB(s) listed below: The changes are noted in Red. SA-035/24 05/31/24 DESCRIPTION There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not. A mechanical seal (A) is used for the water pump. This mechanical seal can seal coolant (B) by sliding a mating ring (C) against a seal ring (D). When the sliding surface temperature of the mechanical seal is more than 248 °F (120 °C) while driving, a small amount of steam (E) is leaked and bleeds through the bleeding hole (F). After drying, the steam leaves a green coolant deposit near the water pump bleed hole (F). This is a normal condition and does not require water pump replacement. The water pump should only be replaced if there is an accumulation of crystallized coolant near the bleed hole. When you encounter a water pump with coolant seepage marks, decide to replace it or not based on the following criteria using sample photos. NOTE: During the initial period of use*, the sliding surfaces of the seals may not yet be fully settled, which can temporarily increase the amount of leakage. Continued use will allow the surfaces to settle, reducing the leakage. Replacing parts that are already settled with new ones will increase the leakage again until the new parts become conditioned. Therefore, replacement should be avoided in this initial period of use. *As a guideline, this applies to vehicles with less than 1,860 miles (3000 km) of mileage.

SA-005-26

Service Bulletin/Repair Instructions

There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method • B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys • 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). • Only Mazda-approved key cutting machines can process these 10-digit codes. • Many older key machines do not support 10-digit codes and cannot be updated to do so. In these cases, dealers will need to purchase one of the newer Mazda-approved key cutting machines capable of handling this requirement. • For a list of current Mazda-approved machines and purchasing options, refer to the Mazda Dealer Equipment Program or view the current Mazda approved key machines below.

SA-001-26

Service Bulletin/Repair Instructions

Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.

SA-061-25

Service Bulletin/Repair Instructions

07-004-25a

Service Bulletin/Repair Instructions

A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

SA-056-25

Service Bulletin/Repair Instructions

When inspected, the differential or PTO oil is dark or black. This is considered normal and NO repair should be performed. During production, differential ring and pinion gears receive a manganese phosphate coating (commonly referred to as black oxide). This coating forms a porous, oil-retentive surface that improves boundary lubrication and reduces adhesive wear during initial contact cycles. Designed as a sacrificial layer, it is gradually removed under load throughout the break-in process. As a result, after the first few hundred miles, or at the initial gear oil service interval, the lubricant may appear darkened by the worn-off coating. It will contain trace ferrous particles from the normal run-in of the gear teeth and bearing surfaces. This condition is expected and does not, by itself, indicate an issue with the differential or PTO gears.

SA-055-25

Service Bulletin/Repair Instructions

Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. NOTE: Before following this Service Alert repair procedure, ensure published TSBs in MGSS have been completed per model year.

SA-020-25a

Service Bulletin/Repair Instructions

There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

SA-051-25

Service Bulletin/Repair Instructions

Noise, Vibration, and Harshness (NVH) Diagnostic Guidelines Diagnostic Guidelines When diagnosing NVH concerns, it is essential to first classify the issue into one of three primary categories: Noise, Vibration, or Harshness. Many customer complaints may involve overlapping symptoms, such as both noise and vibration, so identifying the dominant characteristic is critical. Once the primary symptom is determined, follow the appropriate diagnostic path. For example, if a concern includes both noise and vibration but is related to vehicle speed, the vibration diagnostic path should be followed. When considering component replacement during the diagnostic process, it is best practice to start with the lowest cost or most accessible part unless diagnostic evidence clearly identifies a more expensive or complex component as the root cause. This approach helps minimize repair costs and avoids unnecessary part replacements. For example, a growling or bearing whine noise may be mistakenly attributed to internal components in the differential, transfer unit, or transmission, when the actual source is a wheel bearing. Misdiagnosis like this can lead to unnecessary repairs, added time and cost. To help prevent this, always follow the guidelines in the repair procedure.

SA-052-25

Service Bulletin/Repair Instructions

Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service. Examples of residue or seepage that may not be considered a leak and that may not require repair based on splash shield inspection.

SA-007-25b

Service Bulletin/Repair Instructions

The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery.

SA-044-25

Service Bulletin/Repair Instructions

For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.

SA-042-25

Service Bulletin/Repair Instructions

SA-043-25

Service Bulletin/Repair Instructions

Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

SA-039/25

Service Bulletin/Repair Instructions

Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.

SA-037-25

Service Bulletin/Repair Instructions

When replacing the MAZDA CONNECT tuner and amp unit (TAU) with a replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with an active SAT radio.

CSP13d Dealer Ltr

Warranty Program/Extension

CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.

CSP11a Warranty

Warranty Program/Extension

Mazda Motor Corporation has decided to conduct a Customer Service Program (CSP11) to extend the limited powertrain warranty to 10 years or 120,000 miles, whichever occurs first, for necessary repairs if the covered vehicle has coolant leaks at the cylinder head, around the exhaust manifold. A dealer must inspect and confirm the covered vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for the repair to be covered.

SA-032-25

Service Bulletin/Repair Instructions

Some customers may complain about a noisy HVAC blower motor or odor after a cabin air filter replacement. Foreign debris on the blower motor after servicing the cabin air filter may be the cause. During the removal of the cabin air filter, foreign debris (leaves, dust, dirt....ect.) may fall on the blower motor causing a fluttering type noise or odor.

SA-031-25

Service Bulletin/Repair Instructions

Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.

CSP13c Dealer Ltr

Warranty Program/Extension

SA-007-25a

Service Bulletin/Repair Instructions

The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery’s Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result

CSP13a Parts and Warranty

Warranty Program/Extension

CSP13 - CUSTOMER SERVICE PROGRAM - MAZDA CONNECT INFOTAINMENT SYSTEM LIMITED WARRANTY EXTENSION. As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have “CSP13” listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled “Subject Vehicles CSP13” for details on the covered vehicle models, model year and production VIN ranges.

CSP13b Dealer Ltr

Warranty Program/Extension

09-024-25

Service Bulletin/Repair Instructions

Some vehicles may exhibit following symptoms: 1. The rearview mirror (1) rattles up and down (2) while adjusting the mirror. 2. The rearview mirror (1) makes a rattle noise depending on the road surface conditions while driving. This concern is caused during rearview mirror installation. The adhesive is squeezed out between the windshield and the mirror base. The rearview mirror is assembled on top of the overextended adhesive. The adhesive is softened by heat, and loosening screws, results in a rattling concern.

CSP13a Dealer Ltr

Warranty Program/Extension

CSP13 Dealer Letter

Warranty Program/Extension

CSP13 FAQs

Warranty Program/Extension

CSP13 Parts and Warranty

Warranty Program/Extension

CSP13 Repair

Warranty Program/Extension

07-004-25

Service Bulletin/Repair Instructions

SA-020-25

Service Bulletin/Repair Instructions

SA-016-25

Service Bulletin/Repair Instructions

The new AWD rear differential DOES NOT come with a breather cap on the rear of the differential, therefore a new one will need to be ordered and installed when replacing the differential. NOTE: The breather threads have a sealant and locking compound that prevents it from being reused. Refer to GEPC for the correct part number of the Differential Breather. The instructions on MGSS will be updated soon to include replacing the breather when replacing the differential with a new unit.

SA-004-25a

Service Bulletin/Repair Instructions

Key Transmitter Power Saving Function: When the key transmitter Power Saving Function is turned ON, transmitter battery power consumption is restricted, thereby extending the transmitter battery life and the following will occur: The engine will not start unless the key transmitter is held over the Start Stop button. • Outside door handle lock/unlock touch sensor is inoperative. • Key transmitter indicator lights are inoperative. • The following DTC's may be stored: DTC B13D3:94 (Communication error with remote transmitter) ○ DTC P1260:00 (Immobilizer system problem).

SA-007-25

Service Bulletin/Repair Instructions

06-001-25

Service Bulletin/Repair Instructions

Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.

SA-004-25

Service Bulletin/Repair Instructions

Key Transmitter Power Saving Function: When the key transmitter Power Saving Function is turned ON, transmitter battery power consumption is restricted, thereby extending the transmitter battery life. NOTE: Some customers may complain about an engine no start. This may be caused by the customer inadvertently putting the key transmitter in Power Saving Function.

SA-003-25

Service Bulletin/Repair Instructions

When performing the MGSS Workshop Manual 360° View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST.

CSP11 Owner Letter

Warranty Program/Extension

Dear Mazda Owner: You are receiving this notice because Mazda’s records indicate that your 2019-2020 CX-5, 2016-2020 CX-9, or 2018-2020 Mazda6 vehicle was equipped with a SKYACTIV-G 2.5T (Turbocharged) engine (“Covered Vehicle”). Mazda Motor Corporation has decided to conduct a Customer Service Program CSP (11) to inform you that Mazda is extending the limited powertrain warranty to provide necessary repairs free of charge if your Covered Vehicle has coolant leaks at the cylinder head around the exhaust manifold and to inform you that you may be eligible to receive reimbursement for past out-of-pocket expenses you previously incurred for such repairs on the terms and conditions as described below. Powertrain Warranty Extension: Mazda is extending the limited powertrain warranty to 10 years or 120,000-miles, whichever occurs first, to provide necessary repairs at no cost to you if your Covered Vehicle has coolant leaks at the cylinder head around the exhaust manifold. A dealer must inspect and confirm your Covered Vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for you to receive the repairs at no cost to you.

01-010-24

Service Bulletin/Repair Instructions

CSP11 Parts Warr

Warranty Program/Extension

CSP11 - COOLANT LEAKS AT CYLINDER HEAD WARRANTY EXTENSION For certain 2019-2020MY CX-5, 2016-2020MY CX-9, 2018-2020MY Mazda6 that are equipped with SKYACTIV-G 2.5T engine, the warranty coverage for specific repair of the coolant leak at cylinder head is extended to: 10 years (120 months) or 120,000 miles (192,000 km) whichever comes first, from the original warranty start date CONDITION OF CONCERN On certain subject vehicles, the coolant may leak at the cylinder head around the exhaust manifold.

SA-081-24

Service Bulletin/Repair Instructions

Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.

SA-079-24

Service Bulletin/Repair Instructions

The SKYACTIV-DRIVE FW6A-EL AT uses “Automatic Transmission Fluid (ATF) Type: FZ”. Only use “ATF-FZ” to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

CSP11 Dealer Letter

Warranty Program/Extension

CSP11 Parts

Warranty Program/Extension

CSP11 Repair

Warranty Program/Extension

CSP11

Warranty Program/Extension

Please review the entire Dealer Email below announced on October 17, 2024 for full details regarding this campaign. Warranty Information is at the bottom of the TSB Parts and Warranty information and Repair Procedures will be available by October 25, 2024. Until that time if a vehicle is presented to your dealer with a complaint and CSP11 is visible in eMDCS, please click here and follow instructions in TSB 01-002/23 COOLANT LEAKS AT CYLINDER HEAD and hold claims until the Parts and Warranty Information is available in eMDCS and MGSS.

09-022-24b

Service Bulletin/Repair Instructions

Some customers may complain that the power liftgate (PLG) may open unintentionally while the vehicle is parked or stopped. Due to the shape of the 7th generation remote transmitter, the power liftgate button may be long pressed unintentionally in a pocket or a bag. To eliminate this concern, the keyless control specification has been modified. The button press time has been increased from 0.5 seconds to 1 second.

SA-016-24c

Service Bulletin/Repair Instructions

SA-068-24

Service Bulletin/Repair Instructions

Some customers may complain about scratches on the instrument cluster lens.

SA-062-24

Service Bulletin/Repair Instructions

SA-016-24b

Service Bulletin/Repair Instructions

SA-057-24

Service Bulletin/Repair Instructions

SA-058-24

Service Bulletin/Repair Instructions

Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.

SA-056-24

Service Bulletin/Repair Instructions

Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.

SA-053-24

Service Bulletin/Repair Instructions

Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

09-038-24

Service Bulletin/Repair Instructions

In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the “Speedometer Replacement Label”. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda’s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO’s services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

SA-052-24

Service Bulletin/Repair Instructions

SA-050-24

Service Bulletin/Repair Instructions

Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.

SA-008-24a

Service Bulletin/Repair Instructions

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

SA-011-24b

Service Bulletin/Repair Instructions

Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

09-022-24a

Service Bulletin/Repair Instructions

09-036-24

Service Bulletin/Repair Instructions

At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. • Wrinkles may not be completely removed after the repair is completed. • Leather is a natural material and may develop some wrinkles due to aging and wear during normal useage.

09-035-24

Service Bulletin/Repair Instructions

Some vehicles may experience the seat ventilation system still on after the engine has been turned off, in some cases this causes the battery to be completely discharged and not rechargeable. This is caused by a deterioration in the seat ventilation control unit. To eliminate this concern, the material for the circuit of the seat ventilation control unit has been modified.

SA-011-24a

Other

SA-016-24a

Other

SA-022-24a

Other

Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

07-003-24a

Service Bulletin/Repair Instructions

Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 °F (10 °C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.

SA-035-24

Other

There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.

SA-032-24

Other

09-026-24

Service Bulletin/Repair Instructions

SA-027-24

Service Bulletin/Repair Instructions

Some customers may complain about infotainment center display. Peeling, spider cracks and white dots.

07-003-24

Service Bulletin/Repair Instructions

Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 Â°F (10 Â°C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.

SA-022-24

Service Bulletin/Repair Instructions

09-022-24

Service Bulletin/Repair Instructions

SA-016-24

Service Bulletin/Repair Instructions

PF-24-03

Service Bulletin/Repair Instructions

Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.

09-014-24

Service Bulletin/Repair Instructions

When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).

SA-011-24

Service Bulletin/Repair Instructions

SA-008-24

Service Bulletin/Repair Instructions

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

09-006-24

Service Bulletin/Repair Instructions

Some vehicles may exhibit a creaking or clacking noise when operating the power lift gate (PLG). The noise may be caused by the following: Creaking noise: Dust and dirt accumulates on the sealing portion of the PLG drive unit, reducing sealing performance. Snow and water may enter the PLG drive unit. Humidity then causes rust inside of the unit, resulting in noise. Clacking noise: Since the grease applied on the spring end of the PLG drive unit is insufficient, interference noise is caused when the spring end interferes with the spring guide. The noise has been eliminated by the following mass-production changes: Creaking noise: The sealing structure has been modified to prevent dust/dirt from entering the unit. Clacking noise: The production procedure of the PLG drive unit has been modified to apply sufficient grease to spring end.

06-001-24

Service Bulletin/Repair Instructions

Some customers may complain about a creaking, knocking, rattle or clunk noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. To eliminate this concern, the tightening torque for the steering column nut has been increased.

SA-081-23

Service Bulletin/Repair Instructions

06-004-23b

Service Bulletin/Repair Instructions

Some customers may complain about a creaking noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. To eliminate this concern, the tightening torque for the steering column nut has been increased.

09-007-23c

Service Bulletin/Repair Instructions

At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface.

01-007-23a

Service Bulletin/Repair Instructions

02-003-23

Service Bulletin/Repair Instructions

Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

SA-032-23a

Service Bulletin/Repair Instructions

SA-003-23a

Service Bulletin/Repair Instructions

SA-039-23a

Service Bulletin/Repair Instructions

Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.

06-004-23a

Service Bulletin/Repair Instructions

SA-050-23

Service Bulletin/Repair Instructions

Some customers may complain about scratches on the instrument cluster lens.

06-004-23

Service Bulletin/Repair Instructions

SA-039-23

Service Bulletin/Repair Instructions

Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.

SA-036-23

Service Bulletin/Repair Instructions

09-007-23b

Service Bulletin/Repair Instructions

At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface.

SA-035-23

Service Bulletin/Repair Instructions

Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

SA-032-23

Service Bulletin/Repair Instructions

SA-033-23

Service Bulletin/Repair Instructions

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

05-002-23

Service Bulletin/Repair Instructions

Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738).

SA-031-23

Service Bulletin/Repair Instructions

01-007-23

Service Bulletin/Repair Instructions

09-013-23a

Service Bulletin/Repair Instructions

Some customers may experience electrical devices that cannot be charged through the rear console or the trunk side trim USB power outlet. This may be caused by an excessive external force applied to the USB power outlet. To eliminate this concern, the soldering strength of the USB port has been enhanced.

SA-024-23

Service Bulletin/Repair Instructions

Some customers may complain about any of the following: Infotainment display is blank Rear mount camera is inoperative Foot-motion system is inoperative Rear parking sensor system is inoperative Battery is discharged INTERIOR2 15amp fuse is blown

06-001-23a

Service Bulletin/Repair Instructions

Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.

09-007-23a

Service Bulletin/Repair Instructions

At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface.

SA-016-23

Service Bulletin/Repair Instructions

There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method

SA-012-23

Service Bulletin/Repair Instructions

Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.

09-016-23

Service Bulletin/Repair Instructions

Speedometer replacement procedure

09-013-23

Service Bulletin/Repair Instructions

01-002-23a

Service Bulletin/Repair Instructions

09-011-23

Service Bulletin/Repair Instructions

09-008-23

Service Bulletin/Repair Instructions

SA-007-23

Service Bulletin/Repair Instructions

The rear differential case could develop a crack in the case. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. This concern is caused when the sliding bearing (1) in the coupling (2) is seized and causes the coupling component to fit loosely. The pinion shaft head (3) then contacts the differential case and causes a crack.

01-001-23a

Service Bulletin/Repair Instructions

Some customers may complain about a poor acceleration and rough idling or the CHECK ENGINE light ON with DTC P0301:00, P0302:00, P0303:00, P0304:00.NOTE: Only turbo engines are applicable; non-turbo engines are NOT applicable. In most cases, DTCs P030X stores, but sometimes not. Sometimes the CHECK ENGINE light does not recognize this engine concern. This is caused by the variable valve in the exhaust manifold seizing and causing the exhaust port to become hot and the exhaust valve seat to wear unevenly, resulting in compression leakage. To eliminate this concern, the design of the exhaust manifold has been modified.

07-002-23

Service Bulletin/Repair Instructions

Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 Â°F (10Â°C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced since December 2021 at the supplier.

09-007-23

Service Bulletin/Repair Instructions

At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.

SA-007/23

Service Bulletin/Repair Instructions

The rear differential case could develop a crack in the case NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. This concern is caused when the sliding bearing in the coupling is seized and causes the coupling component to fit loosely. The pinion shaft head then contacts the differential case and causes a crack.

09-006-23

Service Bulletin/Repair Instructions

When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).

RF-23-01

Service Bulletin/Repair Instructions

When servicing SKYACTIV engine vehicles requiring to replace the Oil Galley Plug and Crush Washer, order the required part numbers below. These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.

01-002-23

Service Bulletin/Repair Instructions

Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole or at the outside of the exhaust manifold. Cracks may be caused by: - Deformation of the exhaust manifold during usage causing unexpected force to certain areas of the cylinder head. - Residual stress generated during production in the cylinder head material may be greater than expected. The external force from the exhaust system when driving over bumps may cause unexpected force to certain areas of the cylinder head. To eliminate this concern, the design of the exhaust manifold gasket and the cylinder head has been modified to reduce the force on the cylinder head.

SA-003/23

Service Bulletin/Repair Instructions

01-001-23

Service Bulletin/Repair Instructions

Some customers may complain about a poor acceleration and rough idling or the CHECK ENGINE light ON with DTC P030X:00 (only turbo engines are applicable; non-turbo engines are NOT applicable). - In most cases, P030X is stored, but sometimes not. - Sometimes the CHECK ENGINE light does not recognize this engine concern. This is caused by the variable valve in the exhaust manifold seizing and causing the exhaust port to become hot and the exhaust valve seat to wear unevenly, resulting in compression leakage. To eliminate this concern, the design of the exhaust manifold has been modified.

SA-078-22

Service Bulletin/Repair Instructions

SA-016-22a

Service Bulletin/Repair Instructions

There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

04-005-22

Service Bulletin/Repair Instructions

Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disc plateÃ¢ÂÂs surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit grooves in rear brake disc plate(s). This concern is mostly found on new or low mileage vehicles, when the brakes are new. The grooves may be caused through abrasion from the accumulation of metal particles from the rear brake disc plates. The metal particles get caught between the brake pads and disc plates causing groove damage. To eliminate this concern, the disc plate surface honing process has been changed to reduce metal particle formation. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. This is caused by rust on the brake disc plateÃ¢ÂÂs surface. NOTE: The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.

MT-004-22

Service Bulletin/Repair Instructions

Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.

09-018-22b

Service Bulletin/Repair Instructions

Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.324 or later). The system performance has been improved as follows: Ver. 74.00.324 fixes these software errors (bugs): * If the shift lever is operated quickly while displaying the CarPlayTM screen, the rear view screen may not return to the CarPlayTM screen. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting into the R position.

09-047-22

Service Bulletin/Repair Instructions

Some vehicles may exhibit power outer mirror(s) that do not completely fold in and/or out. NOTE: This concern is unrelated to frozen mirrors in icy weather where snow or ice need to be removed for the mirrors to fold in and/or out. This concern may be caused by the following: - The space between the mirror frame and the inner base may be too tight to allow for proper movement. - Due to insufficient water tightness, water enters the electric fold-in unit and results in corrosion damage. - The friction around the folding mechanism shaft may become increased. To eliminate this concern, the following mass-production changes have been implemented: - The hole (1) in the mirror frame connected to the inner base has been enlarged. - The overlapping area (2) of the water-proof seal (inside electric fold-in unit) has been extended. - The washer material has been improved and an additional washer has been added to the shaft.

02-004-22a

Service Bulletin/Repair Instructions

SA-074-22

Service Bulletin/Repair Instructions

Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. To correct this issue, the ambient temperature sensor has been modified.

SA-075-22

Service Bulletin/Repair Instructions

If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Cell phone charger/accessory in 12V socket (engine no start or unable to turn off) 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple CarplayÃÂ¢ÃÂÃÂ¢/ Android AutoÃÂ¢ÃÂÃÂ¢ will not connect) 6. Over-sized wheels/tires (incorrect GPS location)

07-003-22a

Service Bulletin/Repair Instructions

Some customers may complain about poor A/C performance due to low refrigerant. This may be caused by one of two things. Cause 1: [For 2016-2022 CX-9 with VINS lower than JM3TC******617612 (produced before April 7, 2022)] The condenser is corroded causing leakage of the A/C refrigerant. To eliminate this concern, the anti-corrosion performance of the condenser tube has been improved. Cause 2: [For all 2016-2022 CX-9] The low-temperature side outlet pipe leading to the evaporator of the air conditioner condenser has deteriorated because the structure around the outlet pipe on the low-temperature side of the air conditioner condenser allows mud and salt water to adhere easily. There is no mass production change, but an improved condenser was designed as needed.

SA-008-22a

Service Bulletin/Repair Instructions

Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.

SA-068-22

Service Bulletin/Repair Instructions

The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

SA-066-22

Service Bulletin/Repair Instructions

Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] * B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] * No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. * In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). * In other cases this DTC might be found without a related customer concern. NOTE: In most cases, no dealer visit is necessary.

SA-067-22

Service Bulletin/Repair Instructions

Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: * The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: - The windshield is dirty - The FSC lens is foggy - There is low visibility due to rain, fog or snow - It is at night and there is not enough light - There is direct or reflected sunlight on the FSC - There is problem with the FSC * There is a problem with the AUTOHOLD control function. * There is a problem with the electric parking brake (EPB).

09-032-22a

Service Bulletin/Repair Instructions

01-010-22

Service Bulletin/Repair Instructions

Some customers may experience a squeaking noise may be heard from the exhaust manifold when the idle speed drops from fast idle to normal idle speed during cold start. This is caused by a variable valve being stuck in the closed position. When returning from fast idle to normal, the stuck valve suddenly opens due to thermal change around it which causes abnormal noise. To eliminate this concern, the internal design of the exhaust manifold has been modified.

07-003-22

Service Bulletin/Repair Instructions

Some customers may complain about poor A/C performance due to low refrigerant. This may be caused by the low-temperature side outlet pipe leading to the evaporator of the air conditioner condenser deteriorating because the structure around the outlet pipe on the low-temperature side of the air conditioner condenser allows mud and salt water to adhere easily. There is no mass production change, but an improved condenser was designed as needed.

09-032-22

Service Bulletin/Repair Instructions

SA-001-22d

Service Bulletin/Repair Instructions

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

SA-050-22

Service Bulletin/Repair Instructions

09-024-22

Service Bulletin/Repair Instructions

In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer.

01-007-22

Service Bulletin/Repair Instructions

01-006-22

Service Bulletin/Repair Instructions

This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

SA-039-22

Service Bulletin/Repair Instructions

Some customers may complain about scratches on the instrument cluster lens.

SA-038-22

Service Bulletin/Repair Instructions

Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration.

09-018-22

Service Bulletin/Repair Instructions

Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.311 or later).

02-004-22

Service Bulletin/Repair Instructions

SA-001-22c

Service Bulletin/Repair Instructions

Use the symptom troubleshooting tables to diagnose MAZDA CONNECT concerns.

SA-030-22

Service Bulletin/Repair Instructions

Some vehicles may store DTC B1495:87 (LIN communication error) and cannot be cleared after accessory Trailer Hitch is installed. This may be caused by liftgate foot sensor deactivation procedure not completed during trailer hitch installation.

SA-026-22

Service Bulletin/Repair Instructions

Apple CarPlay / Android Auto Frequently Asked Questions (FAQs)

09-012-22

Service Bulletin/Repair Instructions

SA-018-22

Service Bulletin/Repair Instructions

The WSM shows 3 possible crankshaft sprocket and timing chain combinations (Type A, B and C), but some vehicles have been produced with a combination of Type A timing chain with 2 yellow-colored links with a Type B crankshaft sprocket.

02-003-22

Service Bulletin/Repair Instructions

Some customers may complain that the steering wheel is off center more than 3ÃÂ° even when driving straight on a flat road.

SA-016-22

Service Bulletin/Repair Instructions

There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

SA-014-22

Service Bulletin/Repair Instructions

Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories.

04-001/22

Service Bulletin/Repair Instructions

Some vehicles may exhibit a click or squeak noise from the front brakes under the following conditions: 2016-2022 CX-9 2018-2022 CX-5 (Click noise): 1. When first moving forward or reverse from a stop OR 2. When first applying the brakes while moving forward at slow speeds. Cause: Due to deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Mass-Production Change: None 2016-2018 CX-9 (Squeak noise): During light braking. Cause: Occurs when the front brake pads have been worn to certain levels. As the pads wear, the chamfer goes away and the grease between the pad and the shim deteriorates. Mass-Production Change: As of Apr. 27, 2018, the chamfer shape of the brake pad was improved to increase durability.

01-003/22

Service Bulletin/Repair Instructions

SA-001-22b

Service Bulletin/Repair Instructions

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

SA-006-22a

Service Bulletin/Repair Instructions

07-001/22

Service Bulletin/Repair Instructions

Some vehicles may exhibit an unusual noise in the front A/C unit when the recirculate switch is operated. This is caused by a damaged gear in the air intake actuator. Dust and sand adhered to the grease at the air intake link may disturb the movement of the air intake actuator, resulting in the damaged gear. To eliminate this concern, grease application to the air intake link mechanism to the link pin has been reduced.

01-002/22

Service Bulletin/Repair Instructions

Some vehicles may exhibit a fuel odor at the left / rear area of the vehicle while the engine is idling that usually occurs when the fuel tank is warmed up in hot weather and/or after long distance driving. Depending on wind direction and/or parking environment, the odor may be more noticeable. The odor may be caused by evaporative gas from the gas outlet vent.

SA-006-22

Service Bulletin/Repair Instructions

00-001-22

Service Bulletin/Repair Instructions

SA-009-22

Service Bulletin/Repair Instructions

SA-001-22

Service Bulletin/Repair Instructions

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

SA-008-22

Service Bulletin/Repair Instructions

Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.

MT-001-22

Service Bulletin/Repair Instructions

Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Use a clean towel damped in leather/vinyl cleaner or mild soap to clean the steering wheel. NOTE: Upholstery maintenance and care information can also be found in the Owner's Manual.

SA-001/22

Service Bulletin/Repair Instructions

Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. 6 Bluetooth device will not pair No. 7 Incorrect GPS position No. 8 Voice Recognition Does Not Work No. 9 Cannot Make a Hands-Free Call No. 10 Cannot Play Bluetooth Audio No. 11 Other Symptoms No. 12 How to update the Navigation SD Card Map No. 13 How to Check Navi SD Card VIN Lock

01-006-21-3779b

Service Bulletin/Repair Instructions

Battery Maintenance: This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

09-009-21-3759a

Service Bulletin/Repair Instructions

Rusty Panel at Bottom (Inner Side) of Doors: Some customers may complain about rust at the bottom (inner side) of the doors where the seaming welt is located. It is caused by mud/sand adhering to the side sill, which scratches the paint surface when the door is opened/closed. The mud/sand is most likely brought in by the driver and/or passenger when stepping in and out of the vehicle.

09-012-21-3801b

Service Bulletin/Repair Instructions

Door Lock Will Not Work Using Remote Transmitter and Engine Will Not Start: Some customers may experience all of following symptoms: 1. The door lock/unlock operation will not work using the remote transmitter button. 2. The door lock/unlock operation will not work using the door lock/release touch sensor. 3. The engine will not start using the ignition switch. 4. The transmitter operates by itself. 5. The key battery drains faster than usual. Symptoms 1-3: This may be caused when excess load is applied to the remote transmitter, deforming the electrical terminals and creating poor contact with the battery. To eliminate this concern, the structure in the remote transmitter has been modified to reduce the deformation of the electrical terminals. Symptom 4-5: This may be caused when excessive load is applied to the remote transmitter, creating a gap around the gasket where moisture enters and corrodes the circuit board which in turn drains the key battery faster than usual. To eliminate this concern, the thickness of the case wall on the gasket mounting surface has been increased and the bonding strength of the components has been improved to prevent deformation. Customers having this concern should have their vehicle repaired using the following repair procedure.

01-013-21-3753a

Service Bulletin/Repair Instructions

Coolant Leaks At Cylinder Head: Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold (2).

15-004-21-3835

Service Bulletin/Repair Instructions

NOTE: This Service Information is only applicable for vehicles equipped with a Forward Sensing Camera (FSC), KDD1-67-XCX and GSH7-67-XCX*. If B61L-67-XCX* appears in the GEPC search, the VIN is applicable for this repair only if the part has been previously replaced with KDD1-67-XCX. Some vehicles may exhibit the master warning light (and other warning lights) illuminated while driving, with DTC B115E:76 stored in memory.

SA-019-21e

Service Bulletin/Repair Instructions

MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns

SA-052-21

Service Bulletin/Repair Instructions

For improvement of electrical diagnosis, the SKYACTIVÃÂ® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIVÃÂ® vehicles and compare suspect terminal drag with a good know terminal.To measure the voltage/resistance avoiding any terminal damage.

01-013-21-3753

Service Bulletin/Repair Instructions

Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold (2). Cracks may be caused by: Deformation of the exhaust manifold during usage causing unexpected force to certain areas of the cylinder head. Residual stress generated during production in the cylinder head material may be greater than expected. The external force from the exhaust system when driving over bumps may cause unexpected force to certain areas of the cylinder head. To eliminate this concern, the design of the exhaust manifold gasket and the cylinder head has been modified to reduce the force on the cylinder head.

09-030-21-3838

Service Bulletin/Repair Instructions

Some vehicles may exhibit a rattle, clunk or pop noise from the front of the vehicle while driving. The noise may be caused by loose cowl panel bolts.

MT-002-21a

Service Bulletin/Repair Instructions

Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. E85: A blend of 85% ethanol and 15% gasoline All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V.

SA-019-21d

Service Bulletin/Repair Instructions

MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

MT-002-21

Service Bulletin/Repair Instructions

Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline, E85: A blend of 85% ethanol and 15% gasoline, All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V. What if a customer puts E85 in there Mazda vehicle? Symptoms include: Rough Running, Lean Codes, Misfires and/or misfire codes, Lack of power, Poor fuel economy, Spark knock, Mechanical engine damage.

04-004-21-3821

Service Bulletin/Repair Instructions

Some vehicles may exhibit: Vehicle body vibration when moving from a stop while using the Electric Parking Brake (EPB) automatic release function. Uneven rear brake pad wear. These concerns may be caused because the automatic EPB caliper release timing is too late for the movement of the vehicle. NOTE: Frequent usage of the EPB automatic release function may promote uneven rear brake pad wear. To eliminate these concerns, the EPB control module logic has been modified.

09-021-21-3818b

Service Bulletin/Repair Instructions

All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.230 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of MazdaÃ¢ÂÂs continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software. Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.

05-001-21-3826

Service Bulletin/Repair Instructions

Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on, P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on, P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on, P0780:00 - Gear shifting malfunction, P1738:00 Automatic transaxle internal malfunction. This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.

SA-019-21c

Service Bulletin/Repair Instructions

MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

01-006-21-3779a

Service Bulletin/Repair Instructions

09-025-21-3824

Service Bulletin/Repair Instructions

This service bulletin provides information regarding the proper use of the driverÃ¢ÂÂs floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage.

SA-046-21

Service Bulletin/Repair Instructions

Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting.

09-021-21-3818a

Service Bulletin/Repair Instructions

AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction.

01-001-21-3761a

Service Bulletin/Repair Instructions

Some vehicles may exhibit an occasional rough idle accompanied with DTC P0300:00 (Random misfire) due to the following: 1. While closing the EGR valve, carbon deposit etc. pinched at the valve seat prevents the valve from closing completely. 2. The closed position of the EGR valve is learned improperly as it is not equipped with a position sensor. 3. While idling, the EGR gas improperly mixes with fresh air through the EGR valve that is not closed properly. 4. Misfire occurs. To eliminate this concern, the control software of the PCM has been modified (for service) to force the learning of the closed position of the EGR valve when a misfire is detected at idle.

02-002-21-3769a

Service Bulletin/Repair Instructions

09-023-21-3820

Service Bulletin/Repair Instructions

Some customers may complain that the rear console / cup holder area is warming. The warming is caused by heat radiating from the rear heater core, which is located under the console. The warm air created by the heater core escapes through small gaps and carries heat along the inner walls of rear console / cup holder, causing an increase in temperature.

15-002-21-3812

Service Bulletin/Repair Instructions

Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.

09-021-21-3818

Service Bulletin/Repair Instructions

AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of MazdaÃ¢ÂÂs continuing efforts to improve safety and reduce driver distraction.

SA-019-21a

Service Bulletin/Repair Instructions

MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

SA-042-21

Service Bulletin/Repair Instructions

Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc.) placed on the front passenger's seat.

SA-030-21a

Service Bulletin/Repair Instructions

There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method A. Auxiliary Key Trace Cut Method If only one auxiliary key is lost/missing, some key cutting machines can trace cut a new key blank. 1. Trace cut the new auxiliary key blank(s). B. Auxiliary Key Code Cut Method If both auxiliary keys are lost/missing, use this method for cutting new auxiliary key blank(s). 1. Confirm you have access to a Mazda approved key cutting machine. See Ã¢ÂÂMazda Approved Key Cutting MachineÃ¢ÂÂ table.

09-012-21-3801a

Service Bulletin/Repair Instructions

Some customers may experience all of following symptoms: The door lock/unlock operation will not work using the remote transmitter button. The door lock/unlock operation will not work using the door lock/release touch sensor. The engine will not start using the ignition switch. This is caused when excess load is applied to the remote transmitter and the electrical terminals in it may be deformed, causing poor contact with the battery. To eliminate this concern, the structure in the remote transmitter has been modified to reduce the deformation of the electrical terminals.

SA-041-21

Service Bulletin/Repair Instructions

Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories. The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section once a part is selected. Accessories E-catalog For models prior to 2016: Accessory Parts and Installation Instructions

SA-040-21

Service Bulletin/Repair Instructions

Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.

04-002-21-3809

Service Bulletin/Repair Instructions

Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.

SA-029-21a

Service Bulletin/Repair Instructions

APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions

MT-003-21

Service Bulletin/Repair Instructions

Some vehicles may experience exterior trim heat damage when parked near a glass building. This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.

SA-036-21

Service Bulletin/Repair Instructions

Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles], B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles build on or before March 2, 2019], No DTC - Gen 7 vehicles built after March 2, 2019, DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

SA-034-21

Service Bulletin/Repair Instructions

When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage.

SA-032-21

Service Bulletin/Repair Instructions

SA-033-21

Service Bulletin/Repair Instructions

The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles.

MT-001-21

Service Bulletin/Repair Instructions

If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.

SA-030-21

Service Bulletin/Repair Instructions

Auxiliary key blank cutting procedure: There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method

SA-029-21

Service Bulletin/Repair Instructions

APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlayÃ¢ÂÂ¢ / Android AutoÃ¢ÂÂ¢, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions

09-009-21-3759

Service Bulletin/Repair Instructions

Some customers may complain about rust at the bottom (inner side) of the doors where the seaming welt is located. It is caused by mud/sand adhering to the side sill, which scratches the paint surface when the door is opened/closed. The mud/sand is most likely brought in by the driver and/or passenger when stepping in and out of the vehicle.

09-010-21-3786

Service Bulletin/Repair Instructions

Some vehicles may exhibit power outer mirror(s) that do not completely fold in and/or out.

SA-020-21

Service Bulletin/Repair Instructions

SA-022-21

Service Bulletin/Repair Instructions

When performing the MGSS Workshop Manual 360ÃÂ° View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST.

CSP05c

Service Bulletin/Repair Instructions

MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle

CSP05d

Service Bulletin/Repair Instructions

01-005-21-3778

Service Bulletin/Repair Instructions

The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

01-006-21-3779

Service Bulletin/Repair Instructions

01-003-21-3776

Service Bulletin/Repair Instructions

Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. P2507:00: PCM battery voltage low input

02-003-21-3777

Service Bulletin/Repair Instructions

Some customers may complain that the steering wheel is off center more than 3ÃÂ° even when driving straight on a flat road.

07-001-21-3775

Service Bulletin/Repair Instructions

A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Ã¢ÂÂMazda Air Cooling Coil CoatingÃ¢ÂÂ is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

SA-007-21

Service Bulletin/Repair Instructions

00-001-21-3768

Service Bulletin/Repair Instructions

Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

02-002-21-3769

Service Bulletin/Repair Instructions

09-002-21-3770

Service Bulletin/Repair Instructions

In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer

09-003-21-3771

Service Bulletin/Repair Instructions

When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).

09-004-21-3772

Service Bulletin/Repair Instructions

Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier.

CSP05b

Service Bulletin/Repair Instructions

MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle

SA-039-20b

Service Bulletin/Repair Instructions

The 2020 CX9 Grand Touring and Signature trims come standard with a liftgate handsfree foot-motion detection unit located on the inner surface of the rear bumper. This location is also where the accessory trailer hitch (P/N 0000-8E-N31/0000-8EN31A) is designed to be installed. Due to this location conflict, the foot-motion detection unit must be removed and deactivated in the MAZDA CONNECT system.

SA-004-20c

Service Bulletin/Repair Instructions

In order to ensure key code security, MNAO has restricted key code access for the new auxiliary key. This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all auxiliary keys are lost.

09-005-20-3653a

Service Bulletin/Repair Instructions

Some vehicles may exhibit a rattle, clunk or pop noise from the front of the vehicle while driving. The noise may be caused by loose cowl panel bolts.

09-007-20-3674a

Service Bulletin/Repair Instructions

MT-006-20

Service Bulletin/Repair Instructions

Some customers may complain about the following MAZDA CONNECTÃ¢ÂÂ¢ Temperature Warning message: Ã¯ÂÂ· Display is too Hot. Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECTÃ¢ÂÂ¢ screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).

SA-047-20b

Service Bulletin/Repair Instructions

CRACKED REAR DIFFERENTIAL. The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles.

09-036-20-3756

Service Bulletin/Repair Instructions

Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTHÃÂ® hands-free unit or text messaging related concerns. To improve the handling of BLUETOOTHÃÂ® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.

MT-005-20

Service Bulletin/Repair Instructions

Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after 1200 miles to recheck the engine oil level. 4. After 1200 miles, engine at normal operating temperature, check the engine oil level on the dipstick. 5. Is the engine oil level above the low mark on the dipstick? ÃÂ¯ÃÂÃÂ· Yes - No repair is necessary. ÃÂ¯ÃÂÃÂ· No - Proceed to MGSS online or Workshop Manual (section 01-03 NO. 16 HIGH OIL CONSUMPTION/LEAKAGE).

SA-071-20

Service Bulletin/Repair Instructions

Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. The following 3 adhesives are alternatives available as an equivalent to Loctite 962T: Loctite 272, Loctite 518 Threebond TB-1386H

SA-070-20

Service Bulletin/Repair Instructions

APPLE CARPLAY / ANDROID AUTO FREQUENTLY ASKED QUESTIONS (FAQ): NOTE: The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS - Infotainment - MAZDA CONNECT Updates - Apple Carplay / Android Auto MDARS Activation Instructions

SA-039-20a

Service Bulletin/Repair Instructions

SA-047-20a

Service Bulletin/Repair Instructions

CRACKED REAR DIFFERENTIAL: Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory.

SA-069-20

Service Bulletin/Repair Instructions

ACCESSORY INSTRUCTIONS LOCATION: Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.mazdausa.com

15-003-20-3737a

Service Bulletin/Repair Instructions

Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] (Error signal received from electric power steering (EPS) control module) stored in memory. For Mazda6 and CX-5, the following error messages may appear in the instrument cluster. Ã¯ÂÂ· Front camera sensor system malfunction Ã¯ÂÂ· Forward Smart City Brake Support Malfunction Ã¯ÂÂ· Driver attention alert system malfunction. This may be caused by the battery voltage falling and the EPS control module failing the initial learning for the steering center position while cranking. The FSC detects the error notified by the EPS control module. To correct this concern, the control software of the EPS control module has been modified while the repair procedure modifies the FSC for earlier repairs in the market.

SSPC2c

Service Bulletin/Repair Instructions

SSPC2 - 2020 CX-5 AND 2020 CX-9 POWER LIFTGATE (PLG) CONTROL UNIT CONCERN. Concern Outline: On certain subject vehicles, the PLG Control Unit may not switch to the power saving mode even after pressing the push button start and setting the ignition to the off position, due to improper control logic of the PLG Control Unit. In this condition, if the vehicle is left unused for a certain amount of time, the battery may discharge and run out.

06-003-20-3718b

Service Bulletin/Repair Instructions

Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified.

15-003-20-3737

Service Bulletin/Repair Instructions

Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Ã¯ÂÂ· DTC U0420:68 [Forward sensing camera (FSC)]: Error signal received from electric power steering (EPS) control module. For Mazda6 and CX-5, the following error messages may appear in the instrument cluster. Ã¯ÂÂ· Front camera sensor system malfunction Ã¯ÂÂ· Forward Smart City Brake Support Malfunction Ã¯ÂÂ· Driver attention alert system malfunction. This may be caused by the battery voltage falling and the EPS control module failing the initial learning for the steering center position while cranking. The FSC detects the error notified by the EPS control module. To correct this concern, the control software of the EPS control module has been modified while the repair procedure modifies the FSC for earlier repairs in the market.

09-029-20-3732

Service Bulletin/Repair Instructions

Some vehicles may exhibit poor fitting rear door weatherstrips at the lower/front location. The weatherstrips may be deformed by frequent contact with passengers entering and exiting the vehicle, causing the weatherstrip joint to become enlarged. The enlarged weatherstrip joint does not grip the door panel tight enough when it is refitted.

RF-20-01

Service Bulletin/Repair Instructions

Mazda Accessories has re-released the Front and Rear Bumper Trim kits for the CX-9 (see the table below for application and required components). NOTE: The Front and Rear Bumper Trim Kits are only to be installed on Sport and Touring Models from 2020MY and forward. The Rear Bumper Trim contained within the kit is not compatible with the Handsfree Liftgate Sensor that comes standard on the Carbon Edition (new for 2021), GT, or the Signature Models.

06-003-20-3718

Service Bulletin/Repair Instructions

SA-058-20b

Service Bulletin/Repair Instructions

A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. NOTE: Cylinder head replacement requires MASH authorization.

SA-063-20

Service Bulletin/Repair Instructions

When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage.

SA-062-20

Service Bulletin/Repair Instructions

Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: Ã¯ÂÂ· The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: Ã¯ÂÂ· The windshield is dirty Ã¯ÂÂ· The FSC lens is foggy Ã¯ÂÂ· There is low visibility due to rain, fog or snow Ã¯ÂÂ· It is at night and there is not enough light Ã¯ÂÂ· There is direct or reflected sunlight on the FSC Ã¯ÂÂ· There is problem with the FSC Ã¯ÂÂ· There is a problem with the AUTOHOLD control function. Ã¯ÂÂ· There is a problem with the electric parking brake (EPB).

SSPC2b

Service Bulletin/Repair Instructions

2020 CX-5 AND 2020 CX-9 POWER LIFTGATE (PLG) CONTROL UNIT CONCERN: On certain subject vehicles, the PLG Control Unit may not switch to the power saving mode even after pressing the push button start and setting the ignition to the off position, due to improper control logic of the PLG Control Unit. In this condition, if the vehicle is left unused for a certain amount of time, the battery may discharge and run out.

SA-049-20b

Service Bulletin/Repair Instructions

ENGINE NO START DUE TO LOW BATTERY VOLTAGE. This Service Alert has been replaced by SSPC2 - 2020 CX-5 AND 2020 CX-9 POWER LIFTGATE (PLG) CONTROL UNIT CONCERN

SSPC2a

Service Bulletin/Repair Instructions

MT-003-20

Service Bulletin/Repair Instructions

Some customers may complain about an inoperative power liftgate (PLG) and the any of the following DTC's stored in memory: Ã¯ÂÂ· U3003:16 (Power liftgate (PLG) control module power supply voltage low input) Ã¯ÂÂ· U3003:17 (Power liftgate (PLG) control module power supply voltage high input). This may be caused by low or high vehicle battery voltage.

MT-002-20

Service Bulletin/Repair Instructions

New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.

SA-049-20

Service Bulletin/Repair Instructions

Some customers may experience an engine no start due to low battery voltage. Mazda is aware of the issue and is working on a solution. NOTE: Battery parasitic draw is intermittent. When the condition is present, battery parasitic draw exceeds 65 mA (0.065 A) 40 minutes after key OFF.

DRW29

Service Bulletin/Repair Instructions

DRW29 - 2020 CX-3, CX-30, CX-5, CX-9, MAZDA6 AND MAZDA3 - SECOND PDI OF ALLOCATED FLEET VEHICLES: Concern Outline: There are 597 vehicles contained in this DRW, and all had a paid Pre-Delivery Inspection performed at the port and were to be used as fleet vehicles. These vehicles have since been reallocated to dealerships and due to significant idle time prior to arriving at dealers, the vehicle should have a new Pre-Delivery Inspection performed in order to support a perfect delivery to the customer.

09-006-20-3673a

Service Bulletin/Repair Instructions

When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).

MT-001-20

Service Bulletin/Repair Instructions

SA-004-20b

Service Bulletin/Repair Instructions

SA-026-20a

Service Bulletin/Repair Instructions

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

SA-053-20

Service Bulletin/Repair Instructions

When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order to re-install the original plug from the old transmission.

SA-004-20a

Service Bulletin/Repair Instructions

SA-047-20

Service Bulletin/Repair Instructions

Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory.

SA-040-20a

Service Bulletin/Repair Instructions

Key Transmitter Power Saving Function: When the key transmitter Power Saving Function is turned ON, transmitter battery power consumption is restricted, thereby extending the transmitter battery life. IMPORTANT: Ã¯ÂÂ· The engine will not start unless the key transmitter is held over the Start Stop button. Ã¯ÂÂ· Outside door handle lock/unlock touch sensor is inoperative. Ã¯ÂÂ· Key transmitter indicator lights are inoperative.The key transmitter control functions (i.e. locking/unlocking door, etc.) are operational when pressing the transmitter switches, even while the key power saving function is turned ON.

04-004-20-3679b

Service Bulletin/Repair Instructions

Some vehicles may exhibit a click or squeak noise from the front brakes under the following conditions: Click Noise: 1. When first moving forward or reverse from a stop OR 2. When first applying the brakes while moving forward at slow speeds. Squeak Noise: During light braking.

DRW28

Service Bulletin/Repair Instructions

DRW28 - CHROME WINDOW MOLDING CONCERN FROM STRONG WIND DAMAGE - 2020 CX-5 AND CX-9

00-001-20-3689

Service Bulletin/Repair Instructions

Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

SA-041-20

Service Bulletin/Repair Instructions

Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting.

SA-039-20

Service Bulletin/Repair Instructions

The 2020 CX9 Grand Touring and Signature trims come standard with a liftgate handsfree sensor located on the inner surface of the rear bumper. This location is also where the accessory trailer hitch (P/N 0000-8E-N31/0000-8EN31A) is designed to be installed. Due to this location conflict, the handsfree sensor must be uninstalled and deactivated in the MAZDA CONNECT system. Refer to the deactivation process titled Ã¢ÂÂHandsfree Liftgate Sensor Deactivation/Removal Guide and ProcedureÃ¢ÂÂ in the Trailer Hitch Installation Instruction (attached). NOTE: THE CUSTOMER MUST BE NOTIFIED THAT THEY WILL NO LONGER HAVE THE HANDSFREE SENSOR SHOULD THEY REQUEST THAT THE TRAILER HITCH BE INSTALLED.

04-004-20-3679a

Service Bulletin/Repair Instructions

Some vehicles may exhibit a click noise from the front brakes under one of the following conditions: Ã¯ÂÂ· When first moving the vehicle forward or reverse from a stop. Ã¯ÂÂ· When first applying the brakes while the vehicle is moving forward at slow speeds. Due to deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise.

SA-036-20

Service Bulletin/Repair Instructions

The ownerÃ¢ÂÂs manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Customers should never use inadequate, harsh or aggressive cleaning products on plastic parts. CAUTION: Be aware that when cleaning the brand emblem, never use cleaning products that are highly acidic/alkaline detergent, organic solvents or those with aggressive chemical products, otherwise, the brand emblem may become cracked and/or deformed (as shown in the example below). Always refer customers to the ownerÃ¢ÂÂs manual for proper cleaning using cold or lukewarm water and a mild, neutral detergent.

SA-037-20

Service Bulletin/Repair Instructions

Some vehicles may have one of the following DTCs stored in memory: Ã¯ÂÂ· C1001:92 - Forward sensing camera (FSC) poor field of view Ã¯ÂÂ· B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Ã¯ÂÂ· In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). Ã¯ÂÂ· In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.

SA-032-20

Service Bulletin/Repair Instructions

SiriusXM Traffic Plus and Travel Link are displayed with Mazda in-vehicle factory navigation systems. Both of these services provide information in the U.S. & Canada. NOTE: SiriusXM Traffic Plus and Travel Link subscription is free of charge for 3 years only if equipped with factory installed navigation system. NOTE: 2019-2020 Mazda3 and 2020 CX-30 are not equipped with factory installed navigation system,however, it is available as a dealer installed accessory. SiriusXM Traffic Plus and Travel Link are available on the 2019-2020 Mazda3 and 2020 CX-30 Preferred Package and above, as a paid subscription. Traffic Plus feature requires in-vehicle navigation SD card. SiriusXM Satellite Radio trial subscription is free of charge for 3 months.

02-004-20-3685

Service Bulletin/Repair Instructions

SA-030-20

Service Bulletin/Repair Instructions

Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration.

04-003-20-3668

Service Bulletin/Repair Instructions

Some vehicles may exhibit grooves (1) in rear brake disc plate(s), as shown below. This concern is mostly found on new or low mileage vehicles, when the brakes are new. The grooves may be caused through abrasion from the accumulation of metal particles from the rear brake disc plates. The metal particles get caught between the brake pads and disc plates causing groove damage. To eliminate this concern, the disc plate surface honing process has been changed to reduce metal particle formation.

04-004-20-3679

Service Bulletin/Repair Instructions

Some vehicles may exhibit a click noise from the front brakes under one of the following conditions: When first moving the vehicle forward or reverse from a stop. When first applying the brakes while the vehicle is moving forward at slow speeds. Due to deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise.

SA-011-20a

Service Bulletin/Repair Instructions

Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle.

SA-026-20

Service Bulletin/Repair Instructions

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Audio System, BluetoothÃÂ®, Center Dislay, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux Voice Command, How to Check Navi SD Card VIN Lock.

SA-019-20

Service Bulletin/Repair Instructions

01-002-20-3678

Service Bulletin/Repair Instructions

Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed.Ã¯ÂÂ· P2610:00: Instrument cluster internal engine off timer performance problem Ã¯ÂÂ· P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display Ã¢ÂÂF0-002Ã¢ÂÂ during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km).Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

02-003-20-3677

Service Bulletin/Repair Instructions

Some customers may complain that the steering wheel is off center more than 3ÃÂ° even when driving straight on a flat road. Customers having this concern should have their vehicle repaired using the following repair procedure.

SA-016-20

Service Bulletin/Repair Instructions

Some customers may complain that their seat warmers or seat ventilation do not turn on when the engine is restarted after being left on when turning off the engine. The logic has changed from previous Mazdas where the seat warmers and seat ventilation automatically turned on when the engine was restarted. NOTE: Customers in cold weather are more likely to complain about this if their vehicle is equipped with Mazda Mobile Start (MMS) (not available on Mazda3 or CX-30) because the MMS accessory instructions state the seat warmers WILL turn on when the engine is restarted. The same can happen in the hotter weather with the seat ventilation. This information is incorrect for these vehicles. Both features will now require a manual setting every time the vehicles are restarted after being turned off. Consult the vehicleÃ¢ÂÂs ownerÃ¢ÂÂs manual for more details on proper seat warmer/seat ventilation operation.

SA-009-20

Service Bulletin/Repair Instructions

LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

09-006-20-3673

Service Bulletin/Repair Instructions

When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

09-007-20-3674

Service Bulletin/Repair Instructions

09-008-20-3675

Service Bulletin/Repair Instructions

09-005-20-3653

Service Bulletin/Repair Instructions

Some vehicles may exhibit a rattling noise from the front of the vehicle while driving. The noise may be caused by loose cowl panel bolts.

02-001-20-3655

Service Bulletin/Repair Instructions

Some vehicles may exhibit one or more of the following noises from the front suspension: 1. A creaking noise from under the front of the vehicle (front lower arm bushing) when driving over bumps at approximate 12 - 25 mph (20 - 40 Km/h). The noise occurs when the road surface is wet or after the vehicle has been washed. The noise becomes more noticeable as the bumps get higher. The creaking noise is caused by the front lower arm bushing (A) making a stick-slip noise during wet road conditions. 2. A clunking noise from the front coil spring when driving over bumps. The clunking noise is due to stickslip between the front strut bearing (B) and the coil spring (C). 3. A popping noise from the bump stopper (D) when driving through gutters.To eliminate the noise, the following mass-production changes have been made: 1. The coating treatment of the lower arm bushing has been changed to reduce friction and prevent stick-slip. 2. Protectors have been installed onto the coil springs to prevent stick-slip. 3. The bump stopper has been modified and grease application has been added to prevent the stick-slip.

02-002-20-3651

Service Bulletin/Repair Instructions

09-003-20-3671

Service Bulletin/Repair Instructions

In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealerÃ¢ÂÂs responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Ã¯ÂÂ· Mazda vehicles are manufactured with tamper-proof speedometers. Ã¯ÂÂ· When a speedometer is replaced, the new speedometer will read zero (0) miles. Ã¯ÂÂ· This procedure is extremely important to accurately represent actual vehicle mileage. Ã¯ÂÂ· Prior to speedometer removal, complete the information required on the Ã¢ÂÂSpeedometer Replacement LabelÃ¢ÂÂ. Labels can only be ordered through Mazda eStore. Ã¯ÂÂ· In an effort to achieve a higher level of Customer Experience and retain the value of MazdaÃ¢ÂÂs vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOÃ¢ÂÂs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

SA-004-20

Service Bulletin/Repair Instructions

AUXILIARY KEY CUTTING TEMPORARY PROCEDURE: Currently, Mazda does not have a way to cut the auxiliary keys for the new style remote transmitter as they use a different key code than the previous transmitter key. Follow the repair procedure if one or both auxiliary keys are lost:

09-022-19-3599a

Service Bulletin/Repair Instructions

MT-002-19

Service Bulletin/Repair Instructions

If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

SA-058-19

Service Bulletin/Repair Instructions

WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the oil cooler was missing altogether. IMPORTANT NOTE: ALWAYS REMEMBER TO INCLUDE THE ORIGINAL OIL COOLER WITH THE RETURNED TRANSMISSION CORE!

07-002-19-3616a

Service Bulletin/Repair Instructions

A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Ã¢ÂÂMazda Air Cooling Coil CoatingÃ¢ÂÂ is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

01-022-19-3657

Service Bulletin/Repair Instructions

There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Bulletin is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.

SA-027-19

Service Bulletin/Repair Instructions

Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear Parking Sensors - Rear Seat Entertainment - Smartphone Screen Mirroring - Bumper Trim/Guards - Door Mirror Caps - Fog Lights - Moonroof Wind Deflector - Roof Rack - Side Window Deflectors - Splash Guards - Trailer Hitch - Thule Products - Wheels Locks - Aero Kit - Air Dam - Rear Spoiler - Tunnel Under Bars - Lower Arm Bar - Side Sill Extensions - Arm Rest - Illuminated Door sill Trim Plates - Interior Lighting

SA-053-19

Service Bulletin/Repair Instructions

GUIDE LINES AND PHOTOS TO DETERMINE IF FLUID/OIL SEEPAGE OR LEAK IS SEVERE ENOUGH TO REQUIRE WARRANTY REPAIR OR TO CLEAN AND MONITOR. Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.

MT-004-19

Service Bulletin/Repair Instructions

Some customers may complain about: Ã¯ÂÂ· Intermittent engine no start Ã¯ÂÂ· Instrument cluster red security indicator light ON Ã¯ÂÂ· Engine Start/Start Button Amber indicator light flashing Ã¯ÂÂ· Battery discharge Ã¯ÂÂ· Electrical relay buzzing noise Ã¯ÂÂ· DTC B13D3:94 (Communication error with remote transmitter) stored.This may be caused by: Ã¯ÂÂ· A key in a purse near a cell phone. The cell phone radio waves may interrupt the immobilizer system. Ã¯ÂÂ· An aftermarket cell phone charger. The charger may produce electrical noise that interrupts the immobilizer system. Ã¯ÂÂ· An aftermarket GPS tracker. Some aftermarket devices that are wired to the vehiclesÃ¢ÂÂs wiring harness may create unusual electrical symptoms.

SA-049-19

Service Bulletin/Repair Instructions

Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: Ã¯ÂÂ· MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE Ã¯ÂÂ· CANNOT COMMUNICATE WITH VEHICLE Ã¯ÂÂ· ERROR MESSAGE INSTALLED ON ANDROID DEVICES Ã¯ÂÂ· COMMUNICATION ERRORS Ã¯ÂÂ· MMS CHECK MODE - Use to verify system operation (see below).

DRW27

Service Bulletin/Repair Instructions

On certain subject vehicles, it is possible that the chrome plated window moldings may be dirty or have rust spots. The subject vehicles were parked outside when Typhoon No.17 passed through Hiroshima and Hofu, Japan, and might have been exposed to misty seawater caused by a heavy wind. The sampling inspection revealed that the chrome plated window moldings of certain vehicles became rusty due to seawater mist. All of the potentially affected vehicles have been rinsed with fresh water prior to shipment. OUTLINE OF REPAIR: If the vehicle has a port hangtag with direction to repair a chrome molding, but does not show DRW27 in eMDCS Warranty Vehicle Inquiry, please contact Dealer Recall Help on MXConnect > Warranty. Look for a hangtag placed in the vehicle by the port. If one is found and the vehicle displays DRW27 in eMDCS, inspect the affected molding(s) and perform a secondary cleaning with polishing compound. If any rust or pitting is still present, replace that affected molding(s) with new parts(s).

SA-047-19

Service Bulletin/Repair Instructions

Some customers may have one or more of the following complaints: Ã¯ÂÂ· Infotainment system reboots at times Ã¯ÂÂ· SiriusXM function grayed out Ã¯ÂÂ· SiriusXM stops playing Ã¯ÂÂ· No sound from SiriusXM but other sources work Ã¯ÂÂ· SiriusXM system recovers after ignition OFF-ON. Do not perform any repairs at this time. Mazda is aware of the concerns and is working on a repair. This service information will be updated when a repair is available. NOTE: An interim solution is available for the SiriusXM concerns.

SA-046-19

Service Bulletin/Repair Instructions

On the 2019 Mazda3 (BP) and and all 2020 Mazda vehicles (except CX-3), the CR2032 button cell battery is required for the new type remote transmitter. If it is mistakenly replaced with the conventional CR2025 used in the previous type remote transmitter, it may cause a malfunction. Verify the button cell battery type before replacing it.

SA-045-19

Service Bulletin/Repair Instructions

Currently, Mazda does not have a way to cut the auxiliary keys for the new style remote transmitter as they use a different key code than the previous transmitter key. Follow the repair procedure if one or both auxiliary keys are lost:

SA-042-19

Service Bulletin/Repair Instructions

Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure. NOTE: Before proceeding: Confirm that the Connectivity Master Unit (CMU) is updated to the latest software version. Go to MGSS - Infotainment - MAZDA CONNECT Updates, Confirm that the customers device is updated to the latest software version. Apple Carplay/Android Auto FAQ, go to SA-001/19.

SA266

Service Bulletin/Repair Instructions

MAZDA Mobile start (MMS) cannot communicate with vehicle

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.