Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.
09-009-19-3566
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
09-034-18-3430a
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
09-034-18-3430
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
09-035-17-3080
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the ?SpeedometerReplacement Label?.Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda?s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.With the use of SPECMO?s services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
SA287
DUE TO DIFFERENCES IN THE 1995-1998 PROTÉGÉ IGNITION SWITCH DESIGN, THE REPAIR PROCEDURE AND WARRANTY INFORMATION FOR RECALL 8715J HAS BEEN UPDATED.
0900716
Speedometer replacement procedure
09-034-14-2956
IN ACCORDANCE WITH FEDERAL REGULATIONS, FOLLOW THE PROCEDURE LISTED BELOW WHEN REPLACING A SPEEDOMETER.NOTE:MAZDA VEHICLES ARE MANUFACTURED WITH TAMPER-PROOF SPEEDOMETERS.WHEN A SPEEDOMETER IS REPLACED, THE NEW SPEEDOMETER WILL READ ZERO (0) MILES.THIS PROCEDURE IS EXTREMELY IMPORTANT TO ACCURATELY REPRESENT ACTUAL VEHICLE MILEAGE.PRIOR TO SPEEDOMETER REMOVAL, COMPLETE THE INFORMATION REQUIRED ON THE SPEEDOMETER REPLACE-MENT LABEL. LABELS CAN ONLY BE ORDERED THROUGH MSTORE, NOT MDCS.
0800306
NON GENUINE ACCESSORIES AFFECT AIR BAG OPERATION. *KB
0102504
BATTERY TEST PROCEDURE REQUIREMENTS. *TT
0902604
SPEEDOMETER REPLACEMENT PROCEDURE. *TT
01100R
ON SOME VEHICLES WITHIN CERTAIN VINS, THE DOOR KEY CYLINDER FLAP MAY BREAK ALLOWING A PIECE(S) OF THE FLAP TO ENTER THE CYLINDER THEREBY MAKING IT DIFFICULT TO INSERT THE KEY AND CAUSING KEY ROTATION TO STICK. *TT
00200R
THIS BULLETIN EXPLAINS CAMBER ADJUSTMENT PROCEDURES. *TT
00100
SOME VEHICLES MAY EXHIBIT THE AIR CONDITIONING (A/C) SYSTEM INOPERATIVE WITH THE MALFUNCTION INDICATOR LAMP (MIL) ON. *TT
01399
CONCERNS WITH DOOR KEY WHICH IS DIFFICULT TO INSERT AND / OR ROTATE. *TT
01299
SUBJECT REGARDING PAINT DAMAGE - IRON PARTICLES / INDUSTRIAL FALLOUT / ACID RAIN. *TT
00299
EXPERIENCING POPPING NOISE FROM FRONT BRAKE CALIPER DURING SLOW SPEED BRAKING. *TT
01098
SOME VEHICLES MAY EXHIBIT ERRATIC SHIFTING, O/D OFF INDICATOR LIGHT FLASHING WITH MALFUNCTION INDICATOR LAMP ON AS A RESULT OF THE VALVE BODY HARNESS (TRANSAXLE FLUID TEMPERATURE SENSOR CIRCUIT) BEING PINCHED BY A METAL CLIP WHICH IS ATTACHED TO THE TRANSMISSION CONTROL VALVE BODY, CAUSING A SHORT / OPEN CIRCUIT. *TT
00998
AUTOMATIC TRANSAXLE SELECTOR LEVER IS DIFFICULT TO OPERATE. *YC
00198
CONCERNS REGARDING THE HEARTER NOT WORKING EFFIECIENTLY OR ENGINE TAKES TOO LING TO WARM-UP. *YC
00298
EXPERIENCING POOR ENGINE PERFORMANCE. *YC
01298
CONCERNS WITH MANUAL CONTROL DOOR MIRROR NOT ADJUSTABLE. *YC
01198
SUBJECT ON PASSIVE SEAT BELT RETRACTOR SWITCH. *YC
00598
INFORMATION REGARDING SEAT BELT EXTENDERS. *YC
97102300397
SUBJECT PERTAINING TO MTX OVERHAUL INFORMATION. *YC
97102302097
PRE-PAINTING PREPARATIONS FOR FRONT AND REAR BUMPERS. *YC
97083000997
CONDITION WITH INTERIOR LIGHT DOES NOT ILLUMINATE. *YC
97083001897
UNDER CERTAIN LOAD AND RPM RANGES EXCESSIVE NOISE MAY BE IN GENERATED IN THE EGR BOOST SENSOR CIRCUIT CAUSING DTC P0400 TO BE SET. *YC
970716007/97
CUSTOMERS COMPLAINING OF MIL LAMP ILLUMINATION. *YC
970716015/97
CONCERNS OF RATTLING OR BUZZING NOISES IN THE FRONT OF VEHICLES. *YC
009/97T
INTERIOR LIGHT DOES NOT ILLUMINATE. *TW
012/97S
CENTER ARMREST LATCH SUPPORT REINFORCEMENT INSTALLATION. *TW
012/97T
TACH NEEDLE STUCK ON WRONG SIDE OF STOPPER PIN. *TW
007/97U
A/C REFRIGERANT CHARGING. *TW
008/97
USE OF A/C TRACER DYE. *TW
007/97T
PARTS REPLACEMENT AFTER AIRBAG DEPLOYMENT. *TW
013/97F
SUPPLEMENTAL DIAGNOSTIC PROCEDURES FOR MIL ILLUMINATION. *TW
001/97G
MAINTENANCE FREE BATTERY - DIAGNOSTIC AND CHARGING PROCEDURE. *TW
002/97S
REAR EDGE OF ROOF MOLDING LIFTS. *TW
003/97U
A/C SWITCH MODIFICATION. *TW
004/97U
DAMP CARPET ON PASSENGER SIDE WHEN OPERATING A/C. *TW
003/97G
WIPER MOTOR INOPERATIVE - CIRCUIT BREAKER ACTIVATION. *TW
016/95
HEADLIGHT SWITCH REPLACEMENT. *SD
024/95
TAPPING NOISE AROUND 'B' PILLAR. *SD
030/95
POWER OUTSIDE MIRROR GLASS VIBRATION. *SD
S021/95
RATTLE NOISE FROM HOOD - RUBBER HOOD STOPS OUT OF ADJUSTMENT. *TW
T010/95
REAR DEFROSTER AND INDICATOR LIGHT MAY NOT OPERATE DUE TO SILICONE GREASE STUCK ON THE REAR DEFROSTER SWITCH CONTACT POINTS. *TW
S015/95
NOISE WHEN OPENING POWER WINDOW. *TW
U002/95
BLOWER MOTOR BRUSH NOISE. *TW
S001/95
CRACKING NOISE AT B AND C PILLAR CAUSED BY DOOR LOCK STRIKER BOLTS VIBRATING. *TW
R003/94
CAMBER ADJUSTMENT BOLT. *TW
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.