Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB05-086A
VOLUNTARY SERVICE CAMPAIGN BODY CONTROL MODULE SUB-HARNESS Voluntary Service Campaign ID # P5234 is no longer active. · Repair orders opened after this bulletin’s published date are no longer eligible for reimbursement under Campaign ID # P5234. · Discard all previous versions of NTB05-086.
NTB09-131C
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB23-080D
VOLUNTARY SAFETY RECALL CAMPAIGN 2004-2012 ARMADA, TITAN, AND 2004-2009 QUEST; DRIVER AIR BAG COVER CAMPAIGN ID #: PC944, PC946, PC947, PC949 APPLIED VEHICLES: 2004-2012 Armada (TA60) 2004-2009 Quest (V42) 2004-2012 Titan (A60) Check Service COMM or Dealer Business Systems (DBS) National Service History to confirm campaign eligibility. INTRODUCTION Nissan is conducting this voluntary safety recall campaign on certain specific model year 2004-2012 Armada, 2004-2012 Titan, and 2004-2009 Quest vehicles, to inspect and if necessary, replace the driver Air Bag Cover. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers PC944, PC946, PC947 and PC949 to this campaign. The vehicle specific number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealer’s responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer’s inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097L
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB13-107F
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB09-081J
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
P7245 - 2004-200
Supplemental Restraint System (SRS) Diagnosis Sensor Unit Voluntary Service Campaign ? Expiration Notice ***** Campaign Summary***** In 2007, Nissan launched a Voluntary Service Campaign on certain MY2004-05 Quest and Armada vehicles equipped with optional seat-mounted side air bags to inspect and, if necessary, replace the Supplemental Restraint System (SRS) Diagnosis Sensor Unit. In a small number of these vehicles, an incorrect SRS Diagnosis Sensor Unit may have been installed after an accident repair or part failure. If an incorrect part installation occurred, the optional seat-mounted side air bags may not deploy during a crash. This service campaign is expiring because the required parts and tools are no longer available. ***** What Dealers Should Do ***** 1. Service Comm will deactivate P7245 on any unrepaired VINs on March 20, 2019. - No further action is required. 2. Dealers should submit any open claims for this campaign as soon as possible. Nissan would like to have all claims submitted by March 29, 2019.
NTB07-075d
VOLUNTARY SERVICE CAMPAIGN 2004 - 2005 QUEST AND 2004 - 2005 ARMADA SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS SENSOR UNIT Voluntary Service Campaign ID # P7245 is No Longer Active. - Repair orders opened after March 19, 2019 are no longer eligible for reimbursement under Campaign ID # P7245. - Please discard previous versions of NTB07-075.
NTB17-030a
NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
Revision 1-NEVAP
OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NTB10-104c
TITAN, ARMADA, NV; ENGINE OIL LEAK AT RIGHT SIDE BLOCK BALL PLUG This bulletin has been amended. The APPLIED VEHICLES section has been updated. No other changes have been made. Please discard all previous versions of this bulletin.
NTB17-082a
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-030
NISSAN; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.
NTB17-026
BALL JOINT AXIAL END PLAY PROCEDURE SERVICE INFORMATION When working on the front suspension, use the updated service information in this bulletin along with the Electronic Service Manual (ESM). The updated information in this bulletin is a correction and a supplement to the ESM.
NTB14-068b
POWER MOONROOF INITIALIZATION SERVICE INFORMATION This bulletin has been amended. The APPPLIED VEHICES section and step 3 on page 3 have been revised. No other changes have been made. Please discard all previous versions.
NTB16-071
2004-2014 ARMADA; POWER BACK DOOR INOPERATIVE AND BOLT ON POWER BACK DOOR OPENER LOOSE IF YOU CONFIRM -THE POWER BACK DOOR WILL NOT OPEN OR CLOSE WHEN USING ANY POWER OPEN/CLOSE SWITCH. AND -THE LINKAGE FOR POWER BACK DOOR HAS A LOOSE OR MISSING HEX BOLT (FIGURE 1). ACTION 1. REPLACE THE BOLT SHOWN IN FIGURE 1 WITH A NEW BOLT FROM THE PARTS INFORMATION. -DO NOT REUSE THE OLD BOLT. -CLEAN THE THREADS IN THE LINKAGE BEFORE INSTALLING THE NEW BOLT. -INSTALL THE NEW BOLT AND TORQUE TO 7 NM (0.7 KG-M, 62 IN-LB.). NOTE: REFER TO THE ELECTRONIC SERVICE MANUAL (ESM), SECTION DLK DOOR & LOCK TO GAIN ACCESS TO THE POWER BACK DOOR LINKAGE BOLT.
NTB14033B
SERVICE INFORMATION Replacement 5-speed rear wheel drive Automatic Transmission (A/T) assemblies and replacement control valves (valve bodies) now come with blank Transmission Control Modules (TCMs). Blank TCMs come without software and must be programmed (not reprogrammed) and then configured after they are installed. When ordering a replacement A/T or control valve, use the Nissan electronic parts information systems to obtain the correct software program part number See this bulletin for further detail.
NTB09099A
IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NTB09131B
SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NTB10104B
IF YOU CONFRIM An oil leak at the right side block ball plug behind the alternator. ACTION Use a punch to seat the block ball plug in the hole (refer to the Service Procedure). NOTE - Do not replace the engine block for this incident if it should occur. See this bulletin for further detail.
NTB13028A
SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
NTB14068A
SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further details.
NTB13088A
SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
NTB12078A
SERVICE INFORMATION When diagnosing possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.
NTB00042D
SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
NTB13081A
SERVICE INFORMATION The specifications for the intake and exhaust valves and valve lifter service parts have been changed. * The valve stem length of both intake and exhaust valve has been increased (Figure 1) and are a direct replacement for the shorter style valve. * The related valve lifter cup has been shortened (Figure 2) and the point at which the valve lifter contacts the valve stem has been shortened (not shown). These service parts will require that the valve and valve lifter be replaced at the same time. See this bulletin for further details.
NTB-08-055-A
NISSAN: SRS PRECAUTIONS DURING SERVICE;IMPROPER MAINTENANCE, INCLUDING INCORRECT REMOVAL AND INSTALLATION OF THE SRS, CAN LEAD TO A SERIOUS INJURY OR DEATH CAUSED BY UNINTENTIONAL ACTIVATION OF THE SRS ON ALL NISSAN MODELS WITH THE SRS SYSTEMS. *PE UPDATED 2/21/14. *PE
NTB08055C
SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
NTB-03-074-C
NISSAN: EXTERIOR LAMP FOGGING. OCCASIONALLY WATER IS NOTICED IN THE EXTERIOR LAMPS. THIS IS GENERALLY NOT DUE TO A DEFECT. ALL CURRENT EXTERIOR LAMP ASSEMBLIES ARE VENTED TO THE ATMOSPHERE (NOT SEALED). THIS IS NECESSARY TO ALLOW FOR EXPANSION AND CONTRACTION OF AIR FROM TEMPERATURE VARIATIONS (WARMER OR COLDER) WITHOUT DAMAGE TO THE LAMP. MOISTURE IN THE AIR SOMETIMES TRAVELS INTO AND OUT OF THE LAMP ASSEMBLY THROUGH THESE VENTS. CERTAIN ENVIRONMENTAL CONDITIONS MAY CAUSE MOISTURE TO CONDENSE. THE FOGGING/CLOUDINESS SHOULD DISAPPEAR OVER TIME WHEN THE LAMP IS IN A DRY ENVIRONMENT. NO MODELS LISTED. *PE UPDATED 5/7/10. *PE UPDATED 12/9/13. *PE
NTB11005D
Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
NTB92123D
Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
NTB00033E
SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
NTB04094A
If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
NTB98018G
As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
NTB-13-038
NISSAN: LOCK/UNLOCK REQUEST BUTTON ON OUTSIDE HANDLE DOES NOT RESPOND. *JS
NTB99001A
SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
NTB-04-113B
NISSAN: CLICKING NOISE FROM REAR AXLES DURING TAKE-OFF/ACCELERATION. *PE UPDATED 11/02/11. *PE UPDATED 9/10/12. *PE
NTB12-035
NISSAN: ECM REPLACEMENT PROCEDURES WITH CONSULT III PLUS. APPLIES TO ALL 2004 AND LATER (DOES NOT APPLY TO LEAF/EV) VEHICLES. *JS
NTB-12-028
NISSAN: POWER STEERING HOSE SERVICE PART CHANGE. THE HOSE NOW COMES WITHOUT THE PRESSURE SENSOR. DO NOT DAMAGE PRESSURE SENSOR UPON REMOVAL. IF ONLY PRESSURE SENSOR NEEDS REPLACEMENT, DO NOT REPLACE HOSE. *JS
NTB-11-005
NISSAN: NAVIGATION MAP DATA UPDATE MATRIX. AFFECTING ALL VEHICLES 2003-11 EXCEPT LEAF, EQUIPPED WITH NAVIGATION SYSTEM. CUSTOMER IS MAILED UPDATE DISC(S) OR SD CARD AND INSTALLS DATA; DEALERSHIP IS MAILED UPDATE DISC(S) AND THE DEALERSHIP INSTALLS DATA WHEN VEHICLE IS BROUGHT IN. *PE
NTB-10-072A
NISSAN: FRONT SUSPENSION NOISE. A NOISE (CLUNKING, SQUEAKING, POPPING) CAN BE HEARD WHEN PERFORMING AT LEAST ONE OF THE FOLLOWING ACTIONS: TURNING THE STEERING WHEEL LEFT OR RIGHT, DRIVING OVER SPEED BUMPS, DRIVING ON ROUGH ROADS, ACCELERATING OR DECELERATING AND NOISE IS COMING FROM THE FRONT STABILIZER BAR BUSHING. *PE
NTB-09-101
NISSAN: TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON/FLASHING. NO MODELS OR MODEL YEARS LISTED. *PE UPDATED ON 08-11-2011. *KB
NTB-09-129
NISSAN: VENT CONTROL VALVE REPLACEMENT. WHEN REPLACING THE EVAP CANISTER VENT CONTROL VALVE FOR REASON: USE THE ONE LISTED ON PAGE 2; FOR VENT CONTROL VALVE REPLACEMENT PROCEDURE, REFER TO THE APPROPRIATE SECTION OF THE ELECTRONIC SERVICE MANUALS (ESM; WHEN INSTALLING THE NEW VALVE, DO NOT ADD ANY LUBE TO ITS O RING; FOR FRONTIER (D40 SERIES) ONLY, INSTALL THE PROTECTOR LISTED IN PARTS INFORMATION. *PE INCLUDES 2005-09 FRONTIER. UPDATED 12/8/10. *PE
NTB-08-091B
NISSAN: FUEL GAUGE DOES NOT READ FULL, IS SLOW TO RESPOND, OR IS INACCURATE. *PE
NTB-10-052
NISSAN: THE PROPELLER SHAFT U JOINT (JOURNAL/JOURNAL BEARINGS) IS THE SOURCE OF NOISE AND/OR VIBRATION ON AN APPLIED VEHICLE. DIAGNOSE BY EVALUATING THE U JOINT WITH THE PROPELLER SHAFT REMOVED. REPLACE THE U JOINT (JOURNAL/JOURNAL BEARINGS). *PE
NTB-09-030
NISSAN: THE 12 VOLT BATTERY IS AN IMPORTANT PART OF THE VEHICLE ELECTRICAL SYSTEM AND IS REQUIRED TO STAY CONNECTED WHEN THE ENGINE IS RUNNING. TO PREVENT DAMAGE TO VEHICLE ELECTRONIC COMPONENTS FOLLOW THE INSTRUCTIONS/CAUTIONS. NO MODEL YEARS LISTED. *PE
NTB08-062
SEAT BACK BOARD REMOVAL/INSTALLATION. *NJ
NTB08-049
NISSAN; SPECIAL AUTOMATIC TRANSMISSION FLUID REQUIREMENT. 2004 TO CURRENT NISSAN VEHICLES. *NJ
NTB08-039
2004-2008 TITAN & ARMADA; PASSENGER SEAT SWITCH SERVICEABILITY. VEHICLES WITH BUCKET SEATS ONLY. *NJ
07075
NISSAN SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. VOLUNTARY SERVICE CAMPAIGN - 2004-05 QUEST AND 2004-05 ARMADA SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS SENSOR UNIT. *NJ
07040
LOW POWER WITH WIDE OPEN THROTTLE. *KB
03030
EXTERIOR LAMP FOGGING. *KB
06040
ABS AND/OR BRAKE WARNING LIGHT ON WITH DTC C1179. *TT
06009
MIL ON WITH DTC U1000 OR U1010 STORED IN ENGINE CONTROL UNIT. *TT
06016
GROAN NOISE FROM FRONT BRAKES. NISSAN. *TT
04111
ENGINE WILL NOT CRANK WITH OUTSIDE TEMPERATURE BELOW 10 F. *JB *SC
06007
FUEL GAUGE ALWAYS READS FULL. *TT
04097A
OVERHEAD ROOF CONSOLE CRACKED. *TT
05092
RIGHT FRONT SEAT BACK ASSEMBLY RATTLES AND EXCESSIVE SIDE-TO-SIDE MOVEMENT. *TT
05111
VIBRATION IN STEERING WHEEL AT 29 OR 58 MPH. *TT
02120A
ANTILOCK BRAKING SYSTEM (ABS) LIGHT ON AND / OR DIAGNOSTIC TROUBLE CODE FOR ABS WHEEL SPEED SENSOR. *TT
05096
RATTLE FROM CONDENSER FAN MOUNT. *TT
04131A
ENGINE WILL NOT CRANK AND/OR START AND/OR TRANSMISSION IMPROPER OPERATION. *TT
05086
VOLUNTARY SERVICE CAMPAIGN BODY CONTROL MODULE SUB-HARNESS. ENHANCED ELECTRONIC CIRCUITRY WHICH MAY HELP FURTHERPROTECT A VEHICLE FROM DAMAGE OR FIRE CAUSED BY A SHORT CIRCUIT IN THE ELECTRICAL SYSTEM OF A TOWED TRAILER. *TT
05077
FRONT PASSENGER FLOD FLAT SEAT MANUAL RECLINER INOPERATIVE. *TT
05047
2ND ROW CENTER SEAT BELT BEZEL (GUIDE) IS LOOSE / FALLS OFF. *TT UPDATE *SC
04066B
BRAKE JUDDER FROM FRONT BRAKES.*MR
04066D
BRAKE JUDDER. *SC
04066C
BRAKE JUDDER. *SC
05022
ATF LEAKING FROM AIR COOLER LINE. *EH UPDATE *SC
04104
BRAKE PEDAL FEELS MUSHY, SOFT, OR PEDAL STROKE FEELS TOO LONG. PEDAL HEIGHT ADJUSTMENT. *TT UPDATED *EH
05016
SUNROOF SUNSHADE FABRIC WORN/RIPPED. *TT
05017
FRONT LH/RH WINDOWS - RATTLE NOISE WHEN PARTIALLY OPENED. *TT
04137
2ND ROW SEAT -- LEFT OR RIGHT SIDE -- WILL NOT UNLATCH AND MOVE (TUMBLE) FORWARD. *TT
04113
CLICKING NOISE FROM THE REAR AXLE DURING TAKE-OFF/ACCELERATION. *NM
04116
ROOF MOUNTED DVD MONITOR VIBRATION. *NM
04109
MALFUNCTION INDICATOR LAMP (MIL) ON WITH DIAGNOSTIC TROUBLE CODE (DTC) 01774 STORED. *NM
04087B
FM RADIO RECEPTION-SOUND QUALITY. THIS BULLETIN HAS BEEN AMENDED. THE FORMAT OF THE APPLIED VINS WAS CHANGED. *TT
04103
WIND NOISE FROM REAR SIDE DOOR WINDOW. *TT
04099
NAVIGATION SYSTEM IS INOPERATIVE AND THE DISPLAY SHOWS DISC ERROR OR DVD-ROM VERSION IS NOT CORRECT. *TT
04093
AUTOMATIC BACK DOOR SYSTEM DIAGNOSIS. *TT
04047
CABIN BOOMING NOISE ON ROUGH ROADS. *TT
04056
MALFUNCTION INDICATOR LIGHT ON WITH DIAGNOSTIC TROUBLE CODES P1278, P1279, P1288 AND P1289 A/F SENSOR. *MR THIS BULLETIN REPLACES NTB04-056 DATED 5/15/2004. *TT
04087
FM RADIO RECEPTION-SOUND QUALITY. *TT
04082
CRUISE CONTROL INOPERATIVE DUE TO ASCD CANCEL SWITCH MISADJUSTMENT. *TT
04080
ESSENTIAL TOOL - J-44626 AIR FUEL SENSOR SOCKET. ALSO INCLUDING 2005 ALL NISSAN VEHICLES. *TT
04003A
AIR BAG LIGHT ON CODE B1023 STORED. (THIS BULLETIN UPDATES NTB04-003.) *TT
04034
DVD PLAYER INOPERATIVE. *TT
04029
WATER LEAK FROM SUNROOF. *TT
03101A
ELECTRIC TRAILER BRAKE JUMPER HARNESS. THIS BULLETIN REPLACES NTB03-101. *TT
04003
AIR BAG LIGHT ON, CODE B1023 STORED. *TT
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.