Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB19-033G
Service Bulletin/Repair Instructions
INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB19-042F
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: When contamination or foreign material adhere to the lane camera viewing window on the windshield. When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: Refer to the following pages. Use the search keyword “blinking” in the ESM.
NTB19-071D
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106B
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012I
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055J
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042D
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106A
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-099A
Service Bulletin/Repair Instructions
VIBRATION DURING LIGHT OR MODERATE THROTTLE INPUT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-101
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.
NTB22-099
Service Bulletin/Repair Instructions
VIBRATION DURING LIGHT OR MODERATE THROTTLE INPUT IF YOU CONFIRM A vibration during light or moderate throttle input between 20 â 40 mph, OR RPM flare / slip feeling / vibration during or immediately after a 2 â 3 upshift or 3 â 4 upshift with light or moderate throttle input. ACTION Replace the Torque Converter.
NTB12-055I
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012H
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-026
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the âPASTâ column: ï· Erase the DTC. ï· DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.
NTB20-009A
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0174 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055H
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-027
Service Bulletin/Repair Instructions
MIL ON WITH DTC P062F AND/OR P0603 STORED IF YOU CONFIRM The MIL is ON and DTC P062F (EEPROM) and/or P0603 (ECM BACK UP/CIRCUIT) is stored, And The customer stated the vehicle was recently started after sitting for an extended period of time (i.e., the battery voltage was low while attempting to start the engine). ACTION 1. Test the vehicleâs 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs.
NTB18-008A
Service Bulletin/Repair Instructions
ADAS SYSTEM DTC C1A03, C1A04, AND/OR C1B01 SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-024A
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-120B
Service Bulletin/Repair Instructions
2017 - 2021 ARMADA; INTELLIGENT KEY BATTERY DISCHARGED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-014A
Service Bulletin/Repair Instructions
BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
NTB19-071A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042b
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-079a
Service Bulletin/Repair Instructions
2017 ARMADA; FRONT DISC BRAKE ROTOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY, below. Please discard previous versions of this bulletin.
NTB17-120a
Service Bulletin/Repair Instructions
2017 - 2021 ARMADA; INTELLIGENT KEY BATTERY DISCHARGED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042a
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-065
Service Bulletin/Repair Instructions
2017-2019 ARMADA; ENGINE DOES NOT CRANK IF YOU CONFIRM The engine will not crank and will not start, but the battery test result is OK, OR One of these DTCs are stored: ï· C1142 (PRESS SENSOR) ï· C1A04 (ABS/TCS/VDC SYSTEM) ï· C1A26 (ECD MODE MALFUNCTION) AND The color of the stop lamp switch is solid black, as shown in Figure 1. ACTION Replace the stop lamp switch.
NTB19-057a
Service Bulletin/Repair Instructions
ENGINE KNOCK OR TICK NOISE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-009
Service Bulletin/Repair Instructions
2017-2019 ARMADA; MIL ON WITH DTC P0174 IF YOU CONFIRM The MIL is ON and only DTC P0174 (FUEL SYS LEAN B2) is stored in the ECM. ACTION 1. Confirm the current ECM part number. 2. Reprogram the ECM, if applicable.
NTB17-023c
Service Bulletin/Repair Instructions
2017-2020 ARMADA; OUTSIDE MIRROR(S) LOOSE AT BASE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on page 5. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
NTB19-057
Service Bulletin/Repair Instructions
ENGINE KNOCK OR TICK NOISE IF YOU CONFIRM A knock or tick noise is coming from the engine Or The customer states a knock or tick noise is heard from the engine area. ACTION Refer to REPAIR OVERVIEW on page 3.
NTB19-042
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin applies only to vehicles equipped with a lane camera. SERVICE INFORMATION If the AEB warning light is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: - When contamination or foreign material adhere to the lane camera viewing window on the windshield - When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield - When the lane camera viewing window on the windshield is temporarily fogged up NOTE: - If DTCs are present in any of the following related systems: - Laser/Radar, - ICC/ADAS, or - Lane Camera, Refer to the related Electronic Service Manual (ESM) for diagnosis. - Refer to the following pages for further information.
NTB19-022
Service Bulletin/Repair Instructions
NISSAN; P0171 AND P0174 SERVICE INFORMATION SERVICE INFORMATION Diagnosis for DTCs P0171 (FUEL SYS LEAN B1) and P0174 (FUEL SYS LEAN B2) have been revised for the APPLIED VEHICLES listed above. When performing diagnosis for either of these DTCs, start by using the SERVICE PROCEDURE section of this bulletin. NOTE: The related Electronic Service Manuals (ESM) will be revised in the future to include these diagnostic steps.
NTB19-021
Service Bulletin/Repair Instructions
NISSAN; MIL ON WITH DTC P219A AND/OR P219B STORED This bulletin applies to Titan XD vehicles equipped with a VK56D gas engine only. SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.
NTB13-097g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB17-082b
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB17-023b
Service Bulletin/Repair Instructions
2017-2019 ARMADA; OUTSIDE MIRROR(S) LOOSE AT BASE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-030a
Service Bulletin/Repair Instructions
NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
Revision 1-NEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NTB18-079
Service Bulletin/Repair Instructions
2017-2019 ARMADA; FRONT DISC BRAKE ROTOR SERVICE INFORMATION SERVICE INFORMATION For the Applied Vehicles, the minimum wear thickness for the front disc brake rotors specified in the Electronic Service Manual (ESM) is incorrect. The correct minimum wear thickness is 28.5 mm (1.122 inches). The affected ESMs will be corrected. Until then, do not reference these ESMs for this specification. Refer to the specification stated above.
NTB18-080
Service Bulletin/Repair Instructions
AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.
NTB10-104c
Service Bulletin/Repair Instructions
TITAN, ARMADA, NV; ENGINE OIL LEAK AT RIGHT SIDE BLOCK BALL PLUG This bulletin has been amended. The APPLIED VEHICLES section has been updated. No other changes have been made. Please discard all previous versions of this bulletin.
NTB17-023a
Service Bulletin/Repair Instructions
2017-2018 ARMADA; OUTSIDE MIRROR(S) LOOSE AT BASE This bulletin has been amended. A model year has been added to APPLIED VEHICLES. Discard all previous versions of this bulletin.
NTB03-074m
Service Bulletin/Repair Instructions
FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.
NTB16-018c
Service Bulletin/Repair Instructions
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.
NTB13-107b
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
NTB11-044c
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NTB18-013a
Service Bulletin/Repair Instructions
2017 ARMADA; DTC C1116 AND VDC WARNING LAMP ON This bulletin applies only to vehicles equipped with Distance Control Assist (DCA). This bulletin has been amended. The CLAIMS INFORMATION section has been corrected. No other changes have been made. Please discard previous versions of this bulletin.
NTB18-013
Service Bulletin/Repair Instructions
2017 ARMADA; DTC C1116 AND VDC WARNING LAMP ON This bulletin applies only to vehicles equipped with Distance Control Assist (DCA). IF YOU CONFIRM DTC C1116 (STOP LAMP SW) is stored (Past or Current), AND Customer stated VDC warning lamp was illuminated. ACTION Reprogram the ABS control unit (ABS) per the Service Procedure in this bulletin. - Refer to step 20 on page 8 to confirm that reprogramming is needed.
NTB18-008
Service Bulletin/Repair Instructions
ADAS SYSTEM DTC C1A03, C1A04, AND/OR C1B01 SERVICE INFORMATION This bulletin applies only to vehicles equipped with Automatic Emergency Braking (AEB) or Forward Emergency Braking (FEB). SERVICE INFORMATION If the following ICC/ADAS codes are stored, make sure to follow the diagnostic procedures in the Electronic Service Manual (ESM) before replacing any parts. C1A03 ? VEHICLE SPEED SENSOR -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1A04 ? ABS/TCS/VDC SYSTEM -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1B01 CAM AIMING INCMP -The diagnostic procedure in the ESM includes check and, if needed, repair for LANE CAMERA DTCs before replacing ADAS components. -LANE CAMERA DTC may require adjustment of the lane camera. -If repairs/adjustments are performed for the Lane Camera; when compete, perform DTC Confirmation Procedure again before doing any additional repairs.
NTB17-120
Service Bulletin/Repair Instructions
2017 - 2018 ARMADA; INTELLIGENT KEY BATTERY DISCHARGED SERVICE INFORMATION If the Intelligent Key is stored within 15 feet of the vehicle, the BCM may continue to ?ping? the Intelligent Key keeping it awake. Keeping the Intelligent Key awake may result in discharging its battery in a much shorter period of time than normal (premature battery discharge). Example: The Intelligent Key should not be stored in a lock box or other storage container attached to the outside of the vehicle. To prevent premature Intelligent Key battery discharge, store the Intelligent Key more than 15 feet from the vehicle. If unable to store the Intelligent Key more than 15 feet from the vehicle (for example, when a vehicle is on display in the showroom); the following steps will prevent the BCM from continuing to ?ping? the Intelligent Key: - Disable the welcome light function using the on-board methods outlined in this bulletin, or - Disable the welcome light function using the CONSULT-III plus methods outlined in this bulletin. NOTE: If an Intelligent key is routinely stored within 15 feet of a vehicle while it is in dealer inventory, the Intelligent Key battery should be replaced before the vehicle is delivered to the customer. This will ensure the customer receives Intelligent Keys without premature discharge. Intelligent Key batteries replaced for this reason are not covered under warranty.
NTB17-117
Service Bulletin/Repair Instructions
2017 ARMADA; FAN COUPLING TICK / KNOCK NOISE IN TEMPERATURES 32°F (0°C) OR BELOW IF YOU CONFIRM A knocking or ticking noise is coming from the engine fan coupling when the vehicle is operated at or below 32°F (0°C). ACTION 1. Confirm this bulletin applies. 2. Check and compare your Current ECM Part Number to Table A on page 4. 3. If the part number does not match one in Table A, this bulletin does not apply. Go back to ASIST for further diagnostic and repair information. 4. If this bulletin applies, reprogram the ECM.
NTB17-016e
Service Bulletin/Repair Instructions
ARMADA, TITAN AND TITAN XD; SHIFT SHOCK, LACK OF POWER, AND/OR RPM FLUCTUATES This bulletin applies to vehicles with a gasoline V8 engine only. This bulletin has been amended to add Armada to the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.
NTB11-044b
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-082a
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-016c
Service Bulletin/Repair Instructions
ARMADA, NV, TITAN, AND TITAN XD; 7-3 DOWN SHIFT SHOCK AND/OR LACK OF POWER/HESITATION This bulletin applies only to vehicles with a V8 gasoline engine. This bulletin has been amended throughout. Discard all previous versions of this bulletin.
NTB17-008b
Service Bulletin/Repair Instructions
NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies only to Maxima, Quest, Altima Coupe, Altima Sedan, Pathfinder and Murano vehicles with a 6-cylinder engine and Titan/Titan XD vehicles with a V8 gasoline engine. This bulletin has been amended. The PARTS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-090
Service Bulletin/Repair Instructions
DTC P0036 DIAGNOSTIC INFORMATION This bulletin applies only to Altima and Pathfinder vehicles with a 6-cylinder engine. SERVICE INFORMATION The Electronic Service Manual (ESM) information for DTC P0036 may be inaccurate or incomplete for the Applied Vehicles. If an Applied Vehicle stores a DTC P0036, follow diagnostic procedures in the ESM for Bank 2 A/F Sensor Heater open or shorted.
NTB17-016b
Service Bulletin/Repair Instructions
2017 ARMADA, TITAN AND TITAN XD SHIFT SHOCK, LACK OF POWER, AND/OR RPM FLUCTUATES This bulletin applies only to vehicles equipped with gasoline engine. This bulletin has been amended throughout. Please discard previous versions of this bulletin.
NTB17-008a
Service Bulletin/Repair Instructions
NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies to vehicles equipped with 6-cylinder engines. For Titan and Titan XD, this bulletin applies only vehicles equipped with gasoline engines. This bulletin has been amended in the PARTS INFORMATION and CLAIMS INFORMATION sections. Discard previous versions of this bulletin.
NTB17-024
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED This bulletin applies only to vehicles located in the state of Oregon. IF YOU CONFIRM The Navigation system in an Applied Vehicle reboots when SXM Traffic is enabled. NOTE: Perform the steps in this bulletin ONLY if the above condition occurs while the vehicle is in the state of Oregon. ACTION Update the Navigation system software using the DVD shown on page 2.
NTB17-030
Service Bulletin/Repair Instructions
NISSAN; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.
NTB17-026
Service Bulletin/Repair Instructions
BALL JOINT AXIAL END PLAY PROCEDURE SERVICE INFORMATION When working on the front suspension, use the updated service information in this bulletin along with the Electronic Service Manual (ESM). The updated information in this bulletin is a correction and a supplement to the ESM.
NTB17-016a
Service Bulletin/Repair Instructions
2017 ARMADA; SHIFT SHOCK WITH DOWN SHIFT This bulletin has been amended. The Applied VIN and Date have been removed. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-023
Service Bulletin/Repair Instructions
2017 ARMADA; OUTSIDE MIRROR(S) LOOSE AT BASE SERVICE INFORMATION If the power foldable outtside mirrors are manually folded/unfolded or bumped, the mirror body can become loose at the pivot point. If this occurs, the mirrors should be adjusted again electrically before driving. To readjust the mirrors, press the "CLOSE" switch (see Figure 1) until the mirrors are fully folded in, then press the ?OPEN? switch until the mirrors are fully open. This mirror readjustment procedure is included in section 3 - Pre-driving checks and adjustments of the vehicle Owner?s Manual. NOTE: - DO NOT replace the power foldable outside mirrors for this condition, should it occur. - This condition is not covered under the Nissan New Vehicle Limited Warranty.
NTB17-020
Service Bulletin/Repair Instructions
2017 ARMADA; MIL ON WITH P0090 AND U1000 AND/OR U1001 STORED IF YOU CONFIRM MIL is ON with the following DTC stored: - P0090 (FRP CONTROL SYSTEM) And U1000 and/or U1001 DTCs are stored in one or more other control units. NOTE: If P0090 is set and U1000 and/or U1001 DTCs are not set, this Bulletin does not apply. Refer to the Electronic Service Manual (ESM) for further diagnostic information. ACTION Replace the IPDM with one listed in the Parts Information. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
PC522 Titan and
Service Bulletin/Repair Instructions
ECM Reprogram Dealer Inventory *****Dealer Announcement***** Nissan is conducting a dealer inventory service action to update Electronic Control Module (ECM) software on 7,719 specific 2017 Titan and 4,759 Armada vehicles identified in Service Comm. On the affected vehicles, the ECM software is being updated to refine the MIL illumination logic for the exhaust gas temperature sensor. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. Nissan requests dealers to complete this software update prior to sale to ensure customer satisfaction. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles currently in new dealer inventory are affected by this service action using Service Comm I.D. PC522 for Titan or P6334 for Armada. - New vehicles in dealer inventory can also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to install the updated software. 3. The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle. ***** Dealer Responsibility ***** It is the dealer?s responsibility to check Service Comm using the appropriate campaign I.D for the inspection status on each affected vehicle currently in new vehicle inventory. Nissan requests dealers to perform this repair on new vehicles in inventory prior to being retailed to ensure customer satisfaction.
NTB17-016
Service Bulletin/Repair Instructions
2017 ARMADA; SHIFT SHOCK WITH DOWN SHIFT IF YOU CONFIRM Transmission shift shock when accelerating enough to create a 7th gear to 3rd gear down shift. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm TCM reprogramming applies. 2. If it applies, reprogram the TCM.
NTB17-013
Service Bulletin/Repair Instructions
2017 ARMADA; HEADLAMP AIMING SERVICE INFORMATION When adjusting the headlamps on an Applied Vehicle, make sure to follow the procedures in the Electronic Service Manual (ESM). - Warranty claims for headlamp adjustment are subject to audit. - Claims must have the measurements for dimension H and A (shown in this bulletin) listed on the repair order and on the Technician Comments line of the claim. - Claims submitted without these measurements may be denied. If a customer reports their headlamps are not aimed correctly: 1. Make sure the manual headlamp aiming control is set to '0' (see page 2). 2. Follow the exact procedure in the ESM for headlight adjustment. CAUTION: Do not deviate from the adjustment procedure in the ESM. 3. Refer to the Clarifications of the ESM Vertical Headlamp Adjustment Procedures in this bulletin.
NTB14-068b
Service Bulletin/Repair Instructions
POWER MOONROOF INITIALIZATION SERVICE INFORMATION This bulletin has been amended. The APPPLIED VEHICES section and step 3 on page 3 have been revised. No other changes have been made. Please discard all previous versions.
NTB17-008
Service Bulletin/Repair Instructions
NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies only to Maxima, Quest, Altima Coupe, Altima, Pathfinder and Murano vehicles equipped with V6 engine OR Titan/Titan XD equipped with VK56 engine IF YOU CONFIRM Engine oil is leaking from a valve timing control solenoid valve, And The valve timing control solenoid valve operates correctly and is not externally damaged. ACTION Replace the valve timing control solenoid valve O-ring with a new one using the Service Procedure starting on page 2.
NTB16-124
Service Bulletin/Repair Instructions
2017 ARMADA AND TITAN/TITAN XD; MIL IS ON WITH DTC P2080 AND/OR P2082 IF YOU CONFIRM: The MIL is ON with DTC - P2080 (EXHAUST GAS TEMP SENSOR 1 B1), And/or - P2082 (EXHAUST GAS TEMP SENSOR 1 B2). ACTION: 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM. NOTE: If this bulletin does apply (the ECM needs to be reprogrammed), do NOT replace the exhaust gas temp sensor.
NTB16-123
Service Bulletin/Repair Instructions
PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.
NTB16-116
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS
NTB13-097D
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION THIS BULLETIN HAS BEEN AMENDED. THE TITLE HAS BEEN REVISED, AND THE BULLETIN NOW INCLUDES VEHICLES IN PRODUCTION AS OF THE DATE OF THIS UPDATE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN.
NTB15043
Service Bulletin/Repair Instructions
SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.
NTB14032
Service Bulletin/Repair Instructions
SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.