Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB19-033G
Service Bulletin/Repair Instructions
INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB19-042F
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: When contamination or foreign material adhere to the lane camera viewing window on the windshield. When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: Refer to the following pages. Use the search keyword “blinking” in the ESM.
NTB25-005
Service Bulletin/Repair Instructions
SERVICE INFORMATION If one of the APPLIED VEHICLES has DTC P2100 for “ETC MOT PWR-B1” or P2101 for “ETC FNCTN/CIRC-B1” stored in the Engine Control Module (ECM) with a customer complaint of loss of power, Perform the revised Electronic Service Manual (ESM) procedure noted on page 2 for "PERFORM DTC CONFIRMATION PROCEDURE." HINT: This revised procedure will be added to the ESM in a future update.
NTB19-071D
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NTB24-045
Service Bulletin/Repair Instructions
ENGINE SUPPORT TOOLS APPLIED VEHICLES: 2020-2024 Sentra (B18) SERVICE INFORMATION A new Engine Support Bracket is now available to allow the CVT to be removed from the APPLIED VEHICLES without having to remove the engine. The procedure in this bulletin is different from the procedure currently in the ESM, which will be updated with this information at a later date. Please refer to the SERVICE PROCEDURE in this bulletin for information on how to use these new tools.
NTB22-045B
Service Bulletin/Repair Instructions
RATTLE OR KNOCK NOISE FROM FRONT WHEN DRIVING OVER BUMPS AND/OR TURNING APPLIED VEHICLES: 2021-2024 Sentra (B18) APPLIED DATES: Built from January 2, 2021 to April 11, 2024 IF YOU CONFIRM A rattle or knock noise is heard from the front of the vehicle when driving over bumps and/or turning. HINT: To aid in diagnosis, it is recommended that you view the video clip on ASIST before starting. To view the video full screen, right click the center of the video screen and select “Full Screen”. ACTION Follow the SERVICE PROCEDURE in this bulletin to verify the passenger (RH) side Engine Mounting Insulator is the source of the noise, and replace it with the one listed in the PARTS INFORMATION on the last page. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM A rattle or knock noise is heard from the front of the vehicle when driving over bumps and/or turning. HINT: To aid in diagnosis, it is recommended that you view the video clip on ASIST before starting. To view the video full screen, right click the center of the video screen and select “Full Screen”. ACTION Follow the SERVICE PROCEDURE in this bulletin to verify the passenger (RH) side Engine Mounting Insulator is the source of the noise, and replace it with the one listed in the PARTS INFORMATION on the last page. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NTB21-037D
Service Bulletin/Repair Instructions
DTCS B2E4B-06, B2E60-06, B2E61-06 DISPLAYED AS CRNT IN THE TCU This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM The customer experiences an issue with the NissanConnect® Service remote commands, AND Any of the following DTCs are displayed as CRNT in the Telematics Control Unit (TCU): B2E4B-06 B2E60-06 B2E61-06 HINT: These DTCs are caused by an issue with a cloud-server that is related to the TCU. ACTION 1. Do NOT replace the TCU. Replacing the TCU will not resolve the concern. 2. Send an email to NTB21-037@Nissan-Usa.com. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NTB22-027B
Service Bulletin/Repair Instructions
DTC B2E01-96 (INTERNAL BATTERY) STORED AS CURRENT IN IVC This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the Nissan Data Center to provide various security and convenience services. CONSULT has been updated to allow DTC B2E01-96 for “Internal battery” to be cleared in the TCU. If DTC B2E01-96 is Current/Active in the TCU, and no additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEDURE starting on page 2.
NTB23-078
Service Bulletin/Repair Instructions
REVISION 4 Please discard earlier versions of this bulletin. The announcement from July 2, 2024 has been revised to include the following: • The restriction on parts for this campaign will be removed and dealers will be able to order parts via normal process beginning August 9, 2024 Parts on order in DBS will be fulfilled
NTB23-031A
Service Bulletin/Repair Instructions
DTC B2E1B-06 (AUTOMATIC ECALL) STORED AS CURRENT IN THE IVC APPLIED VEHICLES: 2021-2022 Armada (Y62) 2022-2023 Frontier (D41) 2023 Kicks (P15) 2021-2023 Maxima (A36) 2022-2023 Pathfinder (R53) 2021, 2023 Rogue (T33) 2022-2023 Sentra (B18) 2020-2021, 2023 Titan/Titan XD (A61) 2023 Versa (N18) AMENDMENT HISTORY PUBLISHED DATE REFERENCE DESCRIPTION April 6, 2023 NTB23-031 Original bulletin published July 22, 2024 NTB23-031A Bulletin no longer active This bulletin is no longer active. Please discard previous versions of NTB23-031.
NTB21-115B
Service Bulletin/Repair Instructions
FALSE ACTIVATION OF AEB OR FCW APPLIED VEHICLES: 2021-2022 Altima (L34) 2022-2023 Frontier (D41) 2020-2022 Sentra (B18) APPLIED DATES: Altima: All Frontier: All Sentra: Built on or before March 10, 2022 APPLIED SYSTEMS: Automatic Emergency Braking/Forward Collision Warning IF YOU CONFIRM The customer states they have experienced false activation and/or unexpected braking of the Automatic Emergency Braking (AEB) or Forward Collision Warning (FCW) system, AND There are no related DTCs stored. ACTION 1. Confirm the current ICC/ADAS 2 part number. 2. Reprogram the ICC/ADAS 2, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NTB23-078B
Service Bulletin/Repair Instructions
REVISION 3 Please discard earlier versions of this bulletin. The announcement from June 18, 2024 has been revised to include the following: • Parts for this campaign will continue to remain on restriction until further notice. • Continue to order parts via DBS and orders will be filled as quickly as parts are received. • The parts availability condition will be closely monitored.
NTB20-052C
Service Bulletin/Repair Instructions
REAR DOOR ALERT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-055A
Service Bulletin/Repair Instructions
A/T SHIFT LOCK AND REMOTE ENGINE START INOPERATIVE WITH NEW BCM SERVICE PART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-073C
Service Bulletin/Repair Instructions
INTELLIGENT KEY UNIT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-074B
Service Bulletin/Repair Instructions
BCM SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106B
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-104A
Service Bulletin/Repair Instructions
DIAGNOSING DOOR LOCK OPERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-096A
Service Bulletin/Repair Instructions
LOSS OF ELECTRICAL POWER, ENGINE NOISE, AND/OR BATTERY LIGHT ON This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB24-022
Service Bulletin/Repair Instructions
CVT SUB-ASSEMBLY SERVICE PARTS ARE NOW AVAILABLE SERVICE INFORMATION The CVT Belt & Pulley (sub-assembly) Kit is now available to order. The sub-assembly kit part numbers and other parts needed, if a repair is indicated, are listed in PARTS INFORMATION. ï· This bulletin does not include diagnostic or service procedure information. ï· Refer to the ESM for necessary diagnostic information before performing a CVT repair.
NTB23-018G
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.
NTB23-018F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-037C
Service Bulletin/Repair Instructions
DTCS B2E4B-06, B2E60-06, B2E61-06 DISPLAYED AS CRNT IN THE TCU This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051B
Service Bulletin/Repair Instructions
HORN INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB23-018C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-031
Service Bulletin/Repair Instructions
DTC B2E1B-06 (AUTOMATIC ECALL) STORED AS CURRENT IN IVC SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the Nissan Data Center to provide various security and convenience services. 1. When diagnosing DTC B2E1B-06 (AUTOMATIC ECALL) on an APPLIED VEHICLE: ï· If DTC B2E1B-06 is not âCRNTâ in the IVC, DO NOT replace the TCU. Erase the DTC. No further steps are needed. ï· If DTC B2E1B-06 is âCRNTâ in the IVC, replace the TCU. o Refer to the ESM: REPAIR > DRIVER INFORMATION & MULTIMEDIA > AUDIO, VISUAL & NAVIGATION SYSTEM > REMOVAL AND INSTALLATION > TCU
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-030
Service Bulletin/Repair Instructions
CVT SHIFT SELECTOR LEVER KNOB REMOVAL AND INSTALLATION SERVICE INFORMATION If the CVT Shift Selector Lever Knob needs to be removed or installed for any reason, refer to the SERVICE PROCEDURE in this bulletin, beginning on page 2.
NTB20-016F
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055J
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-013B
Service Bulletin/Repair Instructions
PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-045A
Service Bulletin/Repair Instructions
RATTLE OR KNOCK NOISE FROM FRONT WHEN DRIVING OVER BUMPS AND/OR TURNING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-063D
Service Bulletin/Repair Instructions
COMBINATION METER MODULES OR ABS CONTROL UNITS CANNOT BE SWAPPED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042D
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106A
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-010C
Service Bulletin/Repair Instructions
WINDSHIELD WIPER BLADE PERFORMANCE/DIAGNOSIS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051A
Service Bulletin/Repair Instructions
HORN INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
PMA12 2021-22 Se
Service Bulletin/Repair Instructions
Tire Chain Ownerâs Manual Addendum Voluntary Service Campaign *****Dealer Announcement***** Nissan is providing owners of approximately 183,498 2021-2022 Nissan Sentra vehicles with a supplemental Ownerâs Manual addendum. The 2021-2022 Sentra Ownerâs Manual is missing the caution note about tire size restriction when using tire chains. Customers will be asked to place the addendum, which includes the caution note, inside the Ownerâs Manual that came with their vehicle. *****What Dealers Should Do***** 1. If a dealer receives a supplemental Ownerâs Manual addendum for a vehicle they have retailed, currently have in their new vehicle or pre-owned inventory, or a Nissan Rental Car (NRC), the dealer should either forward the ownerâs manual addendum to the current owner or add the addendum to the Ownerâs Manual in the glove box of any affected vehicle they currently control. 2. Customers receiving this Ownerâs Manual addendum have been advised to place it inside the Ownerâs Manual that came with their vehicle. ***** Release Schedule ***** Owner Notification Nissan will begin mailing the Ownerâs Manual addendum to owners of all potentially affected vehicles beginning February 2023 via U.S. Mail. ***** Dealerâs Responsibility ***** It is the dealerâs responsibility to check Service Comm or DBS National Service History - Open Campaigns using the appropriate Campaign I.D. for the campaign status on each vehicle falling within the range of this voluntary service campaign, which for any reason, enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in dealer inventory. If a VIN subject to this voluntary service campaign was part of a dealer trade, the letter associated with that VIN should be forwarded to the appropriate dealer for service completion.
NTB20-085B
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-027A
Service Bulletin/Repair Instructions
DTC B2E01-96 (INTERNAL BATTERY) STORED AS CURRENT IN IVC This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-037A
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED IN CENTER CONSOLE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-014A
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED IN CENTER CONSOLE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-037B
Service Bulletin/Repair Instructions
DTCS B2E4B-06, B2E60-06, B2E61-06 STORED IN THE TCU This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-104
Service Bulletin/Repair Instructions
DIAGNOSING DOOR LOCK OPERATION SERVICE INFORMATION If a customer describes a concern of a door not opening and/or unlocking properly, on any of the APPLIED VEHICLES, use the Questions for the Customer below to help reproduce the concern, and then follow the SERVICE PROCEDURE starting on page 2 to determine if the Door Lock should be replaced. ï· Do not replace a Door Lock unless instructed to by the SERVICE PROCEDURE. Questions for the Customer: ï· When did you first notice the issue? ï· Is it consistent or intermittent? ï· Under what conditions does it occur? ï· Does it seem more likely to happen to a specific passenger/person in your family? ï· Has there been any change to the issue since it first began?
NTB22-101
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.
NTB20-029F
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB22-067A
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0401 AND/OR P0404 STORED IN THE ECM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
PMA11 2022 Sentr
Service Bulletin/Repair Instructions
Cowl Seam Seal Dealer Inventory ***** Dealer Announcement ***** Nissan is now updating the temporary hold on 418 specific model year 2022 Sentra vehicles identified in Service Comm to a dealer inventory quality action to apply sealant in the engine room. Due to a manufacturing issue, which has since been corrected, a seal was either improperly applied or is missing behind the left front strut tower in the cowl area of the engine room. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. ***** What Dealers Should Do ***** PLEASE FOLLOW THE ATTACHED INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PMA11 ⢠New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ Refer to NPSB 15-460 for additional information ⢠Some vehicles may still be in transit. Please continue to check newly arriving inventory for applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3. Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 4. The service department should submit the applicable warranty claim for the action performed to close the campaign in Service Comm and release the vehicle.
REVISION 1 PMA11
Service Bulletin/Repair Instructions
Cowl Seam Seal Dealer Inventory REVISED October 14, 2022 Please discard earlier versions of this bulletin. The announcement from October 14, 2022 has been revised to include the following: ⢠The procedure in the Original Document for this Quality Action was a DRAFT VERSION of the procedure and was released in error. Disregard previous versions of this procedure.
NTB22-088
Service Bulletin/Repair Instructions
LANE CAMERA OVER TEMPERATURE DTC STORED SERVICE INFORMATION The Lane Camera can become overheated if the interior room temperature or temperature around the camera becomes excessively high, and does not initially indicate a sustained fault. If overheated, the Lane Camera should be cooled to outside ambient temperature, any stored DTCs erased, and then allowed to resume operation. Refer to the ESM for any DTCs that will not erase. This condition may cause the following system functions to be suspended: ï· Vehicle-to-vehicle distance control mode (ICC - Intelligent Cruise Control) ï· Conventional (fixed speed) cruise control mode ï· Steering wheel assistance function ï· AEB (Automatic Emergency Braking) ï· LDW (Lane Departure Warning) ï· I-LI (Intelligent Lane Intervention) ï· Blind Spot Intervention ï· TSR (Traffic Sign Recognition) AND Can store one or more of the following DTCs as PAST or CURRENT: ï· C2501-4B (Front camera unit) ï· C1F05-4B (Front camera unit) ï· C1F6B-4B (Front camera unit) For customer information, see Talk Tip "Customer" statement on page 3.
NTB12-055I
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-013A
Service Bulletin/Repair Instructions
PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-037
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED IN CENTER CONSOLE IF YOU CONFIRM The Intelligent Key fob is not detected when above or around the center console area. ACTION Use the SERVICE PROCEDURE in the bulletin to reconfigure the Hands Free Module (HFM).
NTB22-067
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0401 AND/OR P0404 STORED IN THE ECM IF YOU CONFIRM The MIL is ON and DTC P0401 (EGR A FLOW INSUFFICIENT) and/or P0404 (EGR A CONTROL) is stored in the ECM. AND There are no drivability concerns. ACTION 1. Confirm the current ECM part number. 2. Reprogram the ECM, if applicable.
NTB22-051
Service Bulletin/Repair Instructions
HORN INOPERATIVE IF YOU CONFIRM The horn on an APPLIED VEHICLE is inoperative. ACTION Inspect the horn pad for a pinched ground wire. If a pinched ground wire is found, replace the high and low horns.
NTB22-045
Service Bulletin/Repair Instructions
RATTLE OR KNOCK NOISE FROM FRONT WHEN DRIVING OVER BUMPS AND/OR TURNING IF YOU CONFIRM A rattle or knock noise is heard from the front of the vehicle when driving over bumps and/or turning. HINT: To aid in diagnosis, it is recommended that you view the video clip on ASIST before starting. To view the video clip, open the bulletin on ASIST and select âVideoâ at the bottom of the screen. To view the video full screen, right click the center of the video screen and select âFull Screenâ. ACTION Follow the SERVICE PROCEDURE in this bulletin to verify the passenger (RH) side Engine Mounting Insulator is the source of the noise, and replace it with the one listed in the PARTS INFORMATION on the last page.
NTB19-071B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-085A
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-027
Service Bulletin/Repair Instructions
B2E01-96 (INTERNAL BATTERY) DTC STORED AS CURRENT IN IVC SERVICE INFORMATION CONSULT has been updated to allow DTC B2E01-96 (Internal battery) to be cleared in the Telematics Control Unit (TCU). If DTC B2E01-96 is Current/Active in the TCU, and No additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEURE starting on page 2.
NTB22-026
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
NTB21-063C
Service Bulletin/Repair Instructions
COMBINATION METER MODULES OR ABS CONTROL UNITS CANNOT BE SWAPPED This bulletin has been amended. See AMENDMENT HISTORY, below. Please discard previous versions of this bulletin.
NTB20-029E
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB22-014
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED IN CENTER CONSOLE IF YOU CONFIRM The Intelligent Key fob is not detected when above or around the center console area. ACTION Use the SERVICE PROCEDURE in the bulletin to reconfigure the Hands Free Module (HFM).
NTB13-097J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-063A
Service Bulletin/Repair Instructions
COMBINATION METERS CANNOT BE SWAPPED This bulletin has been amended. See AMENDMENT HISTORY below. Please discard previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the âPASTâ column: ï· Erase the DTC. ï· DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.