Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
15-308-23R
This Service Information Bulletin outlines a systematic procedure for diagnosing parasitic draw (dark/standby current) in vehicles experiencing battery drain when the ignition is off, leading to no-start conditions or frequent jump-starts.This is an revised version of the original bulletin.
16-156-25R
This bulletin announces a design change made to the CVT Control Valve Body. The updated valve body incorporates an enhanced valve sleeve to improve durability. This is an revised version of the original bulletin.
15-304-22R
This Bulletin has been developed to outline the steps for gathering basic but essential information during diagnosis of Infotainment concerns. (This is an revised version of the original bulletin.)
Article Locator
Techtips newsletter locator index.
15-333-25R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. This is an revised version of the original bulletin
02-193-24R
This bulletin provides updated parts information and a service procedure to follow for removing accumulated carbon deposits from fuel injectors and internal engine components (e.g. intake valves and / or manifold, and combustion chambers). (This is an revised version of the original bulletin.)
SubaruNet Annoucement (E
This announcement is requesting retailer staff to retain the EyeSight protective hood covers from Generation 4 EyeSight cameras.
01-167-08R
This bulletin contains additional information for recommended materials listed in the Service Manuals for individual models.
SubaruNet Announcement (R
This announcement provides information on the remanufactured CVT transmission program.
18-230-26
This bulletin announces the diagnostic procedures to be used when DTCs B1571(REFERENCE CODE INCOMPATIBILITY IMMOBILIZER CM TO ECM) and B1572(IMM CIRCUIT EXCEPT ANTENNA CIRCUIT) are detected by Keyless Access with Push Button Start(KACM).
07-240-26R
This Service Information Bulletin was developed to provide interim guidance for vehicles exhibiting DTC B2A20.
03-97-26
This bulletin announces the service manual correction regarding clutch master cylinder reservoir service procedures.
05-97-26
This Bulletin provides the diagnostic procedures to be followed when addressing customer concerns of steering wheel/vehicle body vibration when driving at highway speeds when tire/wheel balance is suspected.
10-105-25R
This bulletin announces the new procedure and Warranty Fail Code for FirstTime air conditioning (A/C) performance concerns possibly resulting from an undetected A/C refrigerant leak.
15-219-18R
This bulletin contains information to help when attempting to complete the STARLINK Telematics subscription process, an Error Code 202 and / or 204 may occur preventing the process from completing successfully
SubaruNet Announcement (A
This announcement provides information on the use of aftermarket services or tools for programming immobilizer keys/fobs.
Subaru Tech Tips Special
This Subaru service and technical support line newsletter provides information on the next phase of TechShare.
15-300-22R
This Bulletin provides the diagnostic procedure for the STARLINK® Remote Engine Start (RES).
Subarunet Announcement (E
This announcement has been created to address difficulties with software updates on Subaru Select Monitors with DST-010 interface firmware has been updated.
09-74-21R
This bulletin provides updated parts information and a service procedure to follow for removing accumulated carbon deposits from fuel injectors and internal engine components (e.g. intake valves and / or manifold, and combustion chambers).
18-226-25R
This Service Information Bulletin provides the Service Manual Correction to the diagnostic procedure for DTC B2A16 (Immobilizer Key Collation Diagnosis).
15-333-25
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
Subaru Tech Tips (Article
Subaru service article locator.
15-130-08R
This bulletin provides information on the load carrying capacity reduced label when a port-installed or retailer-installed accessory exeeds 1.5 percent of the GVWR or 100 pounds, which ever is lower.
07-233-25R
This Bulletin provides details on a new formal testing, charging, and tracking procedure for all 12-volt batteries in new vehicle inventory.
07-236-25
This Bulletin outlines a comprehensive update to the dark current/parasitic draw diagnosis & testing procedures.
07-235-25
In the interest of customer satisfaction Subaru of America, Inc. (SOA) is extending the New Car Limited Warranty coverage in the models listed. The extension will address instances of “phantom braking” or the EyeSight/RAB systems causing unnecessary stoppage/slowing of the vehicle.
16-156-25
This bulletin announces a design change made to the CVT Control Valve Body. The updated valve body incorporates an enhanced valve sleeve to improve durability.
07-233-25
This Bulletin provides details on a new formal testing, charging, and tracking procedure for all 12-volt batteries in new vehicle inventory wjhich must be tested and reported every 30 days.
15-266-20R
This Bulletin provides helpful procedures and best practices to utilize when customers present with concerns relating to the operation of their Gen 2/Gen 3 Telematics system equipped Subaru.
15-320-24R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
SubaruNet Announcement
Subaru of America, Inc. will release an OTA to perform a software update to the DCM. This is a preventive OTA.
13-108-25
This bulletin provides information on paint codes for vehicles in the 2026 line up.
Subaru Service Technical
Subaru Service Technical Support Newsletter special edition.
WRA-25R
In the interest of customer satisfaction, Subaru of America, Inc. (Subaru) is initiating a new voluntary emissions recall for certain 2017 model year WRX and Forester vehicles equipped with a 2.0L turbo engine.
SubaruNet Annoucement
This announcment provides information on the release of the latest software updates to the Subaru Midtronics DSS-5000 Battery Diagnostic tool.
SubaruNet announcement
Subaru of America, Inc. (Subaru) is initiating a new voluntary emissions recall for certain 2017 model year WRX and Forester vehicles equipped with a 2.0L turbo engine.
WRA-25
In the interest of customer satisfaction, Subaru of America, Inc. (Subaru) is initiating a new voluntary emissions recall for certain 2017 model year WRX and Forester vehicles equipped with a 2.0L turbo engine.
15-251-19R
This Bulletin provides additional diagnostics to follow when addressing a Telematics-related DTC B2A16.
SubaruNet Announcement (S
This announcement is to bring attention to the OTA for In-vehicle service appointment scheduler and In-vehicle message center.
01-168-09R
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site.
02-192-24R
This Bulletin announces the diagnostic procedures to be followed when diagnosing engine oil leakage on FA and FB type engines.
14-31-25
This Bulletin announces availability of a User Guide and an informative video to supplement the recent releases to retailers of the SOA321152 and SOA321153 Terminal Test Kits.
09-51-08R
The purpose of this bulletin is to advise of SOA’s revised Catalytic Converter Recycling Program shipping procedure.
WQQ-52R
Due to incomplete repair instructions previously provided in the WQK-47 recall bulletin, the WQQ-52 recall will involve applying additional anti-corrosion material to the four-way (2-2 way) joint connector area of the brake line system on Forester, Impreza, WRX, and STI vehicles previously repaired under the WQK-47 (14V-311) brake line corrosion recall prior to the December 23, 2014 WQK-47 recall bulletin revision. The revisions to the bulletin are for part number changes.
09-123-24R
This bulletin announces the design change made to the high-pressure fuel pump developed to prevent DTC P0087 (Fuel Rail/System Pressure – Too Low Bank 1).
16-103-16R
This bulletin has been developed in response to a small number of customer concerns regarding fluid seepage found coming from the CVT assembly.
15-317-24R
In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the Data Communication Module (DCM) Warranty from 3 years (36 months) of 36,000 miles to 8 years (96 months) or 100,000 miles, whichever comes first.
Subarunet Announcement
This announcement is in regard to special service tool shipment will be shipped directly to the Subar retailers during February.
RC5 Head Unit OTA
A head unit OTA will be available via cellular network for Mid and High Grade CP1.5 head units.
02-193-24
This bulletin provides updated parts information and a service procedure to follow for removing accumulated carbon deposits from fuel injectors and internal engine components (e.g. intake valves and / or manifold, and combustion chambers).
07-59-07R
This bulletin is for information purposes only.The bulletin adresses design changes of the headlamps and rear combination lamps, where moisture and or condensation may develop on the inside of the lamp lenses.
15-312-23R
This bulletin announces repair procedures to be used when diagnosing dark current draw (parasitic draw) on vehicles equipped with Gen 1 Data Control Modules.
15-298-22R
This Service Information Bulletin announces the preferred practices to be used when handling vehicles equipped with Gen2 Telematics which are enrolled in the Subaru STARLINK® Security Plus Service featuring Stolen Vehicle Recovery Plus with Immobilizer.
02-192-24
This Service Information Bulletin announces the diagnostic procedures to be followed when diagnosing engine oil leakage on FA and FB type engines.
07-178-21R
This Service Information bulletin is being released as guidance for proper testing and charging of vehicle batteries.
15-320-24
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
02-191-22R
This bulletin announces availability of the NEW genuine Subaru engine oil filter.
15-316-24R
This bulletin announces the procedures required to reprogram the DCM (Data Communication Module) in Gen1 Subaru vehicles in response to the 3G network sunsetting.
03-94-24
This bulletin outlines the judgment criteria to be used when inspecting front transverse link bushings to reduce unnecessary bushing replacement.
Thermo Control Valve Vide
This thermo control valve video contains information on the replacement of thermo control valve.
13-107-24
This Bulletin provides SOA paint codes to help eliminate possible confusion for 2025 MY vehicles.
05-91-24
This Bulletin provides guidance for diagnosing a leaking front or rear suspension strut.
06-90-24
This bulletin provides diagnosis and procedure information to be applied when diagnosing potential fluid leaks on front and rear brake calipers. This information has been developed to reduce unnecessary brake caliper replacement.
16-112-18R
This bulletin announces a design change to the CVT select lever (shifter) mechanism in response to isolated customer concerns of not being able to remove the key from the ignition switch when the vehicle is in Park.
FAQ 15-317-24R
T16 Warranty Extension (15-317-24R) Frequently Asked Questions.
15-321-23R
This bulletin provides a repair procedure when diagnosing dark current draw on vehicles with GEN 1 Data Control Modules.
17-19-24
Due to limited part supply, the availability of the passenger front seat cushion may not satisfy demand. To reduce extended downtime for the customer, this bulletin announces the diagnostic and repair procedures to be used when DTC B1760 (Occupant Detection Sensor Mat). The use of WUM-98 sensor harness kit should be used in place of the cushion assembly.
Subaru notice to
This letter provides information regarding the warranty extension for the Telematics Data Communications Module (DCM).
SubaruNet Announ
This announcement provides information in regard to the extension of the basic new car limited warranty for the Telematics Data Communication Module (DCM). This coverage will apply to the vehicles listed for vehicles sold or leased in the United States.
15-316-24
This bulletin provides procedures required for reprogramming the Data Communication Module (DCM) in Gen 1 Subaru vehicles due to sunsetting of the 3G network.
15-317-24
Subaru of America, Inc. (Subaru) is extending the Data Communication Module (DCM) warranty from three years (36 months or 36K miles) to eight years (96 months or 100K miles), whichever comes first. This extension is in light of the rare cases of dead batteries experienced by customers.Â
09-99-23R
This bulletin addresses rare cases of engine surg or jolting when the operator releases the accelerator from half-throttle.
09-113-23
This bulletin announces diagnostic procedures and availability of new Engine Control Module (ECM) reprogramming files to address DTC P2404 (Evap System Leak Detection Pump Sense Circuit Range/Performance) detection.
07-207-22R
In the interest of customer satisfaction, Subaru of America, Inc. is extending the New Car Basic Warranty coverage for the 12 Volt batteries used in the above listed models and model years beyond the original three (3) years or thirty six thousand miles (36,000), whichever comes first.
09-110-23R
This Service Information Bulletin announces diagnostic service procedures to be followed when DTC P0420 (Catalyst System Efficiency Below Threshold Bank 1) is detected by the Engine Control Module (ECM).
09-110-23
This Service Information Bulletin announces diagnostic service procedures to be followed when DTC P0420 (Catalyst System Efficiency Below Threshold Bank 1) is detected by the Engine Control Module (ECM). If DTC P0420 is found to be stored in the ECM, follow the diagnostic procedures outlined below.
18-231-23
This Bulletin announces additional information regarding error codes 1403- 1407 encountered when attempting an adjustment/calibration of the EyeSight® system after body repair procedures have been performed.
15-285-21R
This Bulletin provides reference tables and photos to use for determining the infotainment head unit supplier and generation.
12-249-23R
This bulletin announces the recommended cleaning procedures to followed when encountering vehicles with long time exposure to pollen on painted surfaces on vehicles imported from Japan. This bulletin does not apply to SIA built vehicles.
02-131-12R
The purpose of this Bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the timing chain cover, front camshaft cap, camshaft carrier and / or upper oil pan.
16-131-20R
This Service Information Bulletin provides an updated diagnostic flow along with an IMPORTANT caution to follow for certain CVT solenoid related DTCs as listed.
09-84-22R
This bulletin announces Warranty Extension and design changes made to the front exhaust pipe and covers to address the concerns of some customers regarding a rattle-type noise or fluttering sound coming from the undercarriage, during acceleration.
Subarunet Announ
As part of Subaruâs dedication to customer satisfaction, Subaru of America, Inc. (SOA) is announcing an extension to the Emissions Warranty for Front Exhaust Pipe Bellows cracks on certain 2017-2018MY Forester vehicles. This will extend coverage under the Emissions Warranty on vehicles sold or leased in the United States.
5-88-21R
This bulletin announces a design change made to the front stabilizer bushings.
18-229-22
The purpose of this bulletin is to provide a description of current changes to Service Manuals.
15-302-22
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
Subaru Tech Tips
Special Edition, 2012 current model subaru evaporative diagnostics and smoke testing.
15-298-22
This Bulletin announces the preferred practices to be used when handling vehicles equipped with Gen2 Telematics which are enrolled in the Subaru STARLINK® Security Plus Service featuring Stolen Vehicle Recovery Plus with Immobilizer.
05-88-21
This bulletin announces a design change made to the front stabilizer bushings.
12-288-20R
This bulletin announces a design change made to the Slide Rail components of the left and right front power seat frame / track assembliesd.
12-203-16R
This bulletin provides a procedure to address customer concerns of a squeaking sound originating from where the front seat belt buckle assembly attaches to the seat frame.
18-219-22
This bulletin announces the Service Manual correction for the diagnostic trouble tree for DTC C2521 and/or DTC 21.
18-221-22
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
15-192-22R
This bulletin has been developed to outline the steps for gathering basic essential information during diagnosis and repair of the Infotainment concerns. (Applicable to all models with Harman or Denso CP1 Infotainment).
15-291-22
Going forward when a customerâs vehicle is equipped with a DCM that does not have Software version ID DCM_06.00.17_20190816 installed and they wish to subscribe to Starlink Telematics Service, the DCM must be replaced.
09-85-22
This bulletin announces design changes made to the front exhaust pipe covers.
09-84-22
This bulletin announces design changes made to the front exhaust pipe and covers to address the small number of customer concerns regarding a rattle-type noise from the undercarriage during acceleration.
02-189-22
This Bulletin announces design changes to the engine oil and CVT fluid drain plugs.
WRB-21R
In the interest of customer satisfaction, Subaru of America, Inc. (Subaru) is initiating a service program to check and, if necessary, replace the air conditioning condenser assembly in certain 2017 and 2018 model year Forester vehicles.
16-102-16R
This bulletin provides a new flow chart and additional diagnostic tools to assist technicians with troubleshooting DTC P0841- SECONDARY OIL PRESSURE SENSOR PERFORMANCE.
02-188-21
This bulletin announces an additional service procedure for timing chain and / or cam sprocket replacement on FA and FB type engines.
05-79-20R
This bulletin announces a change made to the wheel lug nuts.
15-195-16R
This bulletin provides important information regarding diagnosis and replacement (when applicable) of the STARLINK Telematics Data Communication Module (DCM) along with a new claim submission requirement.
18-216-21
This bulletin provides a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
09-78-21
This bulletin announces the availability of Engine Control Module (ECM) reprograming files to correct DTC P015A and/or P015B.
15-208-17R
This bulletin announces availability of an enhancement to the Gracenote database included in the vehicles listed equipped with F10 7â Navigation and 7â Display Audio head units.
04-27-21R
As part of Subaruâs dedication to customer satisfaction, Subaru of America, Inc. (SOA) is announcingan extension to the Basic New Car Limited Warranty for the Electronic Power Steering (EPS) GearBox Assembly for certain 2012-2018 MY vehicles.
Subaru Owner Let
As part of Subaru of Americaâs dedication to customer satisfaction, this letter is to inform you of an extension to the Basic New Car Limited Warranty for your vehicleâs Electronic Power Steering Gear Box Assembly.
15-177-14R
This bulletin provides information to help diagnose and address different conditions relating to customer concerns which may arise when operating the new-generation âGen 2â and âGen 2.1â F10 Navigation and Display Audio systems.
15-280-21R
Gen1 Telematics Reprogramming for 3G Sunset.
07-195-21
This bulletin outlines changes in the service procedure for replacement of the Power Rear Gate control module.
02-187-21
This bulletin outlines changes in the service procedure for engine oil pressure inspection.
18-207-21
Description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
05-63-18R
This bulletin announces a design change made to the forward bushing used in the front lower control arm to address customer concerns of a rattle-type sound and / or a possible vibration felt in the steering wheel.
05-76-20R
This bulletin announces availability of new front wheel hub assemblies incorporating bearing surfaces having increased resistance to imperfections resulting from shock loads.
WRB-21
In the interest of customer satisfaction, Subaru of America, Inc. (Subaru) is initiating a service program to check and, if necessary, replace the air conditioning condenser assembly in certain 2017 and 2018 model year Forester vehicles.
11-199-20R
This bulletin announces availability of reprogramming files to optimize the Engine Control Module (ECM).
06-59-17R
This Service Information bulletin announces availability of a new front brake pad shim kit to specifically address customer concerns of a squeaking or squealing sound on the models listed above.
10-87-17
This bulletin provides a service procedure to address customer concerns of a rattling-type sound coming from the defroster vent grille area of the instrument panel (IP) near the base of the windshield.
12-223-17
This bulletin provides a procedure for replacement of the black foam rubber insulating cushions for the roof spoiler.
14-22-16R
To help reduce confusion and increase technician efficiency, Subaru of America, Inc. (SOA) has developed the following cross reference list to help locate the appropriate Special Service Tool.
WTJ-70R
Subaru of America, Inc. (Subaru) is initiating a Service Campaign for certain 2017 model year Forester normally aspirated vehicles with CVT transmissions. Subaru has determined vehicles affected by this Service Program require additional CVT fluid.
18-204-21
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
15-267-20R
This bulletin provides information related to the telematics system's Automatic Collision Notification (ACN) and Advanced Automatic Collision Notification (AACN) feature operation, diagnostic tips, and best practices.
03-82-18R
This bulletin announces a design change to the clutch release bearing.
15-205-16R
This bulletin announces new reprogramming file availability and the software installation procedure to address additional operational concerns received from the field and listed involving âGen 2â F10 Navigation and Display Audio units with 7â display.
05-79-20
This Service Information Bulletin announces a change made to the wheel lug nuts.
05-70-19R
This bulletin announces a design change made to the rear wheel / brake backing plates.
16-131-20
This Service Information Bulletin provides corrected diagnostics containing a revised flow for certain CVT solenoid related DTCs.
10-19-20
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
12-289-20R
In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Warranty for the rear gate stays on the listed models and model years.
18-200-20
This bulletin provides a description of current changes to Service Manuals.
15-269-20R
In the interest of providing continued customer satisfaction, Subaru of America, Inc. (SOA) is extending the Basic New Car Limited Warranty coverage for the Condenser component of the Air Conditioning system on all 2017 and a limited number of 2018MY Forester model vehicles.
05-76-20
This bulletin announces availability of new front wheel hub assemblies incorporating bearing surfaces having increased resistance to imperfections resulting from shock loads.
06-79-20
This bulletin announces availability of new master cylinder application shaft seals.
12-289-20
In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Warranty for the rear gate stays on the listed models and model years. This will apply to Forester models with or without the power rear gate (PRG).
15-271-20
This service information bulletin announces discontinuation of both the "Stitcher" app and the related News Radio feature from the STARLINK app lineup effective 12 midnight on Thursday, September 24, 2020.
15-269-20
In the interest of providing continued customer satisfaction, Subaru of America, Inc. (SOA) is extending the basic New Car Limited Warranty coverage for the Condenser component of the Air Conditioning system on all 2017 and certain 2018 MY Forester model vehicles.
15-266-20
This Service Information Bulletin provides helpful procedures and best practices to utilize when customers present with concerns relating to the operation of their Gen 2 Telematics system equipped Subaru.
15-267-20
This document discusses some of the conditions that may trigger an Automatic Collision Notification (CAN) (Gen1) or Advanced Automatic Collision Notification (AACN) (Gen2), without a collision, airbag deployment, or accident taking place.
12-288-20
This bulletin announces a design change made to the Slide Rail components of the left and right front power seat frame / track assemblies used on the models listed.
01-181-20
All Models (Vehicle Cleaning- COVID-19Best Practices)
07-174-20
This service bulletin provides details of a correction to the diagnostic procedure for DTC B2350- REAR RADAR COMMUNICATION ERROR on the models listed.
WUK-96R
Subaru of America, Inc. (Subaru) is initiating a service campaign for certain 2015-2018 Forester 2.0L Turbo and 2016-2018 WRX models which may experience a loosening of the front exhaust pipe nuts.
12-284-20
This bulletin announces availability of new interior door handles which will address isolated concerns of the chrome finish peeling.
14-24-20
This service information bulletin outlines a procedure for Subaru Special Tool Kit number J-53014.
17-17-13R
This bulletin provides information regarding Event Data Recorder (EDR) functionality which has been incorporated into the airbag system.
07-75-13R
This Bulletin provides information regarding DTC P0606 related specifically to the determination of this code on Forester Turbo and applicable WRX models.
07-171-20
This Service Information Bulletin is in response to several battery sensor replacements resulting from improper removal and/or installation practices.
18-198-20
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
WUM-98R
Subaru of America, Inc. (Subaru) is recalling certain 2015-2018 model year Forester vehicles to replace the passenger-side front airbag Occupant Detection System (ODS) harness. A total of 366,282 U.S. vehicles will be affected by this recall.
03-83-20R
This bulletin announces availability of new shift forks and the corresponding sleeve and hub assembly to address isolated customer concerns of a rattling / vibration -type sound from the shift knob. The sound is primarily reported while driving in 4th gear between 1900 and 2500 rpm.
15-199-16R
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field and listed below involving the Clarion Display Audio unit with 6.2" display.
15-204-16R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
11-197-20
This bulletin announces availability of reprogramming files to optimize the Engine Control Module (ECM). These new files address concerns of the check engine light coming on and setting a DTC P0400: EGR âAâ FLOW. The DTC can set if the ECM tests the EGR system when ambient / intake air temperatures are below freezing.
11-199-20
This bulletin announces availability of reprogramming files to optimize the Engine Control Module (ECM). The new logic will address isolated concerns of a hard start condition occurring in cold weather (+10 degrees Fahrenheit or lower) and / or high-altitude areas. When this scenario occurs, the A/F learning control values move toward lean.
07-152-19R
This bulletin announces availability of new power window switch assemblies.
07-167-20
This bulletin announces availability of a new stop lamp switch for the models listed above equipped with LED - type rear combination lamps.
11-195-20
This bulletin announces availability of a new vacuum hose assembly for the positive crankcase ventilation (PCV) system incorporating improved sealing to prevent potential oil seepage.
11-194-20
This Service Information Bulletin addresses inquiries regarding the labels applied to the tumble generator valve (TGV) motors used on certain replacement intake manifold assemblies.
Subaru Retailers
The available inventory update for the WUM-98 harness
10-96-19
This bulletin announces availability of a new HVAC blower motor unit assemblies developed to address isolated concerns of the blower motor becoming inoperative. If this issues occurs on models with Auto A/C, the blower fan may become totally inoperative. If this issue occurs on models with Manual A/C, the blower fan may operate on high speed only. The root cause of these conditions is water intrusion into the blower motor causing rust and corrosion to develop. Over time, the blower motor may begin to draw more electrical current to operate. if that occurs, the additional draw can cause the related fuse and/ or blower resistor to fail. To address this condition, additional packing has been added to improve sealing of the blower unit case along with development of a new style cabin air filter which also in corporates improved sealing.
WUM-98
Subaru of America, Inc. (Subaru) is recalling certain 2015-2018 model year Forester vehicles to replace the passenger-side front airbag Occupant Detection System (ODS) harness. A total of 366,282 U.S. vehicles will be affected by this recall.
WUK-96
Subaru of America, Inc. (Subaru) is initiating a service campaign for certain 2015-2018 Forester 2.0L Turbo and 2016-2018 WRX models which may experience a loosening of the front exhaust pipe nuts. On certain affected vehicles, the six (6) front exhaust pipe (EPF) nuts at the cylinder heads may not have been tightened sufficiently due to variations in production. As a result, these nuts may become loose during use and cause exhaust leakage. A leak occurring at the front exhaust pipe may result in deterioration of emission performance. As a result, affected vehicle may fail to meet emission levels certified by the EPA and/or California ARB.
Subarunet Anounc
To assist with customer inquiries regarding the ODS recall, please use the attached list of answers to questions you can expect in the coming days.
15-253-19
This Service Information Bulletin provides the answer to potential inquiries regarding the STARLINK app being unable to play music files stored on a customerâs Android® phone / device through the head units (H/U) used in the applicable models listed above. This information is applicable ONLY to Android devices operating with Operating System (OS) version 10. IOS (AppleTM) devices are not affected.
12-272-19R
This bulletin announces a design change made to the front door glass run channels. Water can enter the run channels and cause a stick-slip (judder) condition to occur as the door glass opens and closes. The judder is transferred through the window regulator mechanism in the form of mechanical resistance to the electric window motor. On models equipped with the Auto-up and Auto-down feature, if the level of this resistance increases enough, the auto-reversing (anti-entrapment) feature can activate and cause an inability to close the window.
11-191-19R
This bulletin announces availability of a new Engine Control Module (ECM) for the models listed above designed to address DTC P2610: âECM/PCM ENGINE OFF TIMER PERFORMANCEâ. Under certain RARE conditions, an electrostatic surge may influence the ECMâs internal timer used after the engine is turned off and store a DTC P2610 in memory. Hardware in the ECM has been changed to eliminate any impact from electrostatic surges.
11-191-19
This bulletin announces availability of a new Engine Control Module (ECM) for the models listed above designed to address DTC P2610: âECM/PCM ENGINE OFF TIMER PERFORMANCEâ. Under certain RARE conditions, an electrostatic surge may influence the ECMâs internal timer used after the engine is turned off and store a DTC P2610 in memory. Hardware in the ECM has been changed to eliminate any impact from electrostatic surges.
05-69-19
This Service Information Bulletin announces a change made to the rear subframe retaining bolts used on the models listed above. The design changes provide the bolt with an increased durability against rust.
06-68-19R
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. This will prevent the pad from dragging due to corrosion buildup which may result in uneven or premature wear of the replacement brake pads. This additional instruction applies to all models with brake pads using the upper and lower pad clips and has been added to the brake pad installation procedures found in the related Service Manuals.
02-163-16R
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. The applicable Service Manuals will be revised with this new information in the near future.
02-182-19
This Service Information bulletin announces a design change made to the TGV assemblies used on the Forester Turbo models and WRXs listed above. Condensation resulting from EGR system operation may enter the area between the TGV shaft and bearing. Over time, corrosion can develop and impede movement of the TGV shaft and cause any of the DTCs P2004, 2005, 2006 and /or P2007 to set. The material of the TGV shaft has been changed to stainless steel to optimize corrosion resistance.
07-154-19
This Service Information bulletin provides a revised Step to follow when diagnosing a DTC B2513- LATCH CONDITION FAILURE. The number of wiring checks found in Step 9 has been reduced from six to three as shown in the illustration below. The Service Manual will be updated with these revisions in the near future.
07-152-19
This bulletin announces availability of new power window switch assemblies developed to address the following customer concerns: ? Power windows inoperative from the driver?s door master and / or passenger front door switch ? Unable to remotely operate other door windows from the driver?s door master switch ? One-Touch Auto Up / Down features inoperative from either / both front door switches
02-170-17R
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. The new seal will eliminate potential oil seepage into the wire harness connector portion of the valve. If oil seeps into the connector, over time, the Check Engine lamp may illuminate and set various AVCS-related DTCs.
15-239-19
This Service information bulletin announces a design change made to the Cargo Net ? Rear Replacement Hardware Kit (F551SAG301). The new part number is F551SAN010. The change was made to address concerns regarding the ?mushroom? anchors either pulling out of the trim panel and or gapping visibly at the base of the anchor between the black plastic spacer and trim panel.
16-120-19
This bulletin provides a procedure to follow for addressing customer concerns of a shuddering condition or chattering -type sound heard or felt when making sharp turns. If an applicable vehicle presents with the condition as described, it is recommended to perform the transfer clutch break-in procedure as described.
02-178-18R
This Service Information bulletin announces a design change made to the rubber timing hole access plug to improve its retention and prevent water intrusion into the converter case.
11-169-16R
This bulletin announces the availability of reprogramming files to optimize the ECM. These new files will address customer concerns of: ? Spark knock (ping) during high intake air temperature operation ? Surge on acceleration due to phantom knock detection ? Check Engine light illumination resulting from DTC P113A and / or P0137 being stored in the ECM memory.
15-237-19R
This bulletin provides a diagnostic procedure for a chattering-type sound originating from the a/c compressor assembly. In the case where a refrigerant leak is identified as coming from the a/c condenser, the level of refrigerant oil may also drop and cause the internal vanes of the compressor to make a chattering-type sound. A new-style A/C condenser has been established with enhanced corrosion resistance.
02-134-12R
The purpose of this bulletin is to announce a change to the specification of the valve springs used in the FB engine. The new springs have different color paint marks to help identify their application.
16-119-19
This Service Information bulletin announces availability of a new control valve assembly (valve body) designed to prevent false detection of DTC P0841 and / or illumination of the AT Temp light. Testing has revealed in some limited cases, air bubbles (aerated fluid) may enter certain pressure circuits within the control valve assembly causing fluid pressure control and adjustment to be calculated incorrectly resulting in DTC P0841. The shape of these circuits has been changed to prevent this occurrence.
15-237-19
This bulletin provides a diagnostic procedure for a chattering-type sound originating from the a/c compressor assembly. In the case where a refrigerant leak is identified as coming from the a/c condenser, the level of refrigerant oil may also drop and cause the internal vanes of the compressor to make a chattering-type sound. A new-style A/C condenser has been established with enhanced corrosion resistance.
04-23-18R
This bulletin provides helpful tips to simplify the diagnosis of sound concerns originating in the electronic power steering (EPS) gearbox (steering rack) assembly. If a vehicle presents with a ?rattling?, ?knocking? or possibly a ?clanging? type sound coming from the steering rack and / or a vibration felt through the steering wheel, use the flow chart below to help make diagnosis of the concern easier.
11-187-18
This bulletin announces reprogramming file availability to optimize the ECM and address isolated customer concerns of hesitation on acceleration. The new logic provides enhanced ignition timing control during Exhaust Gas Recirculation (EGR) operation.
07-133-18
This Service Information Bulletin announces design changes to the engine?s knock sensor which will help improve vehicle assembly line efficiency and increase durability. In some cases, the Check Engine light may illuminate and a knock sensor-related DTC set in the ECM memory: P0327, P0328, P0332 and P0333. The knock sensor for DIT engines is now utilized for NA engines to improve durability and resistance to heat.
04-24-18
This bulletin announces a new Electronic Power Steering (EPS) control module for the models listed above. These new EPS control modules address a limited number of customer concerns regarding increased steering effort which may occur during freezing temperatures after a cold start. The cause has been identified as a frozen relay contact inside the control module. Illumination of the EPS warning lamp can also occur and a DTC C2532 may be stored.
03-82-18
This Service Information bulletin announces a design change to the clutch release bearing used on the models as listed above. During assembly of the bearing, a different type of grease is used which has a higher resistance to heat. In cases where the operator keeps a foot on the clutch pedal for extended periods, an increased amount of heat is generated which can cause the grease inside the bearing to deteriorate. In a case of prolonged clutch pedal application, seizure of the bearing can occur with potential damage to other related components.
12-251-18
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully.There is a latch to keep the glove box closed on both sides of the glove box door. If the door is closed without using enough force to engage both latches or by pushing it shut on just one side instead of in the middle, one may close and not the other. Over time, if the door is not fully closed with both latches, high cabin temperatures along with weight of the items inside the glove box may cause the assembly to deform slightly and a gap to develop.
04-23-18
This Service Information bulletin provides helpful tips to simplify the diagnosis of sound concerns originating in the electronic power steering (EPS) gearbox (steering rack) assembly. If a vehicle presents with a ?rattling?, ?knocking? or possibly a ?clanging? type sound coming from the steering rack and / or a vibration felt through the steering wheel, use the flow chart below to help make diagnosis of the concern easier.
16-116-18
This Service Information bulletin provides details about revised CVT select lever (shifter) components. The shape of the lock plate and output of the shift lock solenoid have been changed.
16-115-18
In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Powertrain Warranty coverage for the Continuously Variable Transmission (CVT) on the above listed models and model years from the original five (5) years or sixty thousand (60,000) miles (whichever comes first) to ten (10) years or one-hundred thousand (100,000) miles (whichever comes first). This change is not in response to any specific condition, rather it is to provide customers with added assurance regarding the function and overall performance of their CVT. Additionally, vehicles which are beyond one-hundred thousand (100,000) miles at the time customer notification letters are mailed are being offered additional coverage for a period of one-year from the date of the customer notification letters.
15-232-18
This Service Information bulletin announces a change made to the lens portion of the fog light assembly. The new lens has optimized light distribution characteristics while remaining interchangeable with the original type.
18-195-18
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes. We advise you to always refer to the STIS web site when looking for the latest Service information.
12-204-16R
This bulletin provides potential source locations and procedures to help isolate areas of the vehicle which may be generating popping, clicking or creaking sounds when the body is in a ?twisting? condition. This can occur while driving on rough, irregular or uneven road surfaces or even during lowspeed maneuvers such as pulling into or backing out of a driveway. Production information and field reports received indicate where multiple layers of the vehicle?s body structure are spot-welded together, primarily in the ?D?-pillar and rear gate opening areas, a ?stick-slip? condition can occur between the layers and cause these types of sounds to occur. Service information has been released previously describing similar conditions which involved accessing and then punching or separating the layers of metal and applying a lubricant to prevent recurrence. Those same techniques may also provide good results on these vehicles too but, in some cases, a Body Shop repair may be required.
07-108-16R
This Service Information Bulletin provides a revised troubleshooting procedure and tips to follow when diagnosing a DTC B1650- ?Occupant Classification System Malfunction?. This DTC may also be accompanied by B1760, B1761, B1771 or B1795 as found in the Occupant Detection control module. The new procedure is designed to help avoid unnecessary part (seat cushion assembly) replacements.
12-234-18
This bulletin provides a repair procedure for replacing the foam cushion installed between the top front edge of the IP and the windshield glass. Use the supplied Service Procedure to address a customer concern involving the foam cushion becoming visible above the IP near the defroster vent outlets.
04-21-18
This bulletin announces availability of a new Electronic Power Steering (EPS) gear box assembly designed to address a VERY limited number of customer concerns regarding uneven steering effort felt when turning left or right. In areas where high concentrations of road salt are used to melt ice and snow, corrosion may develop and cause a portion of the gear box housing to crack if the vehicle were to suffer a large enough impact from hitting a pothole or similar type of road hazard.
07-136-18
TURBO MODELS ONLY. This bulletin announces availability of new parts to address a limited number of reports involving an engine vibration felt when at idle after the engine is up to operating temperature. In some cases, the above engine misfire DTCs may also result causing the Check Engine light to illuminate in error.
05-63-18
This bulletin announces a design change made to the forward bushing used in the front lower control arm to address customer concerns of a rattle-type sound and / or a possible vibration felt in the steering wheel. The material for the cushion portion of the front bushing has been changed.
07-128-18R
This Service Information bulletin provides a measurement and adjustment procedure for the stop lamp switch. An improperly adjusted (or faulty) stop lamp switch can cause any of the DTCs listed to set and result in the related system?s warning lamp to illuminate.
04-20-18
This Service Information bulletin announces a running change made to the Steering Angle Sensor. The (new) -style originally used on Legacy and Outback has been adapted.
15-223-18
This bulletin outlines design changes made to the Condenser Assembly to help increase productivity during assembly. In addition, the new part utilizes materials with increased anti-corrosion performance.
09-68-18
This Service Information bulletin announces a design change to the exhaust system cover. The purpose of the change is to improve parts integration (or ?commonality?) between models.
10-88-18
This bulletin announces a change made to the Automatic Climate Control Head Assembly. The change will address concerns where the temperature selected for cooling ?feels? warmer to the customer than the temperature displayed. The new programming will adjust the threshold for when cooling occurs to improve the air conditioning system?s cooling effect making it more closely match the customer?s selected temperature.
18-192-18
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes.
12-231-18R
This bulletin announces a design change to the air vent grille located in the lower portion of the trunk (or cargo) area. The shutters of the vent grille are designed to open briefly and relieve cabin pressure when the doors are shut with the windows fully closed. The vent grilles have rubber ?shutters? which occasionally, may catch on the frame (case) portion and not close properly allowing outside air / odor to enter the cabin.
02-173-18
2.0L Turbo Models only. This bulletin announces availability of a special turbocharger air intake duct designed to prevent EXTREMELY RARE occurrence of ice formation from condensation in the duct?s PCV system passages.
07-130-18
This bulletin describes a design change to the center bracket component of the window regulator assembly. The change was made to address customer concerns of the front door glass shuddering while opening or closing. Moisture accumulation in the run channels can cause a stick-slip / vibration condition as the glass goes up and down resulting in the shudder.
F10-Gen2-NAV-15-
TECHNICAL SUPPORT GUIDE FOR NAVIGATION AND AUDIO F10 GEN2 SYSTEMS.
12-231-18
( 2017-2018MY Impreza - 5 Dr Only)
15-215-18
Models with FujitsuTEN (F10) Gen 2.0 / 2.1 Navigation or Display Audio Head Units ONLY. This bulletin provides a repair procedure to address specific, confirmed customer concerns of: ? Audio output interruption every 2-3 seconds when listening to AM or FM radio broadcasts ? No audio output at all when attempting to listen to a HD Radio broadcast.
UPDATE - Removal
The corrected update files are now available for download from Subarunet. TSB 15-20516R has been revised with new file names where applicable and re-posted to STIS.
f10-audio-navi-d
Subject: Removal of Certain Fujitsu 10 Audio / Navigation Update Files from Subarunet The following update files have been temporarily removed from Subarunet due to potential quality concerns with the 2nd file used in those updates. Retailers are requested to take the following action: ? If any of the following Fujitsu 10 Audio / Navigation files have been downloaded and saved locally, please discontinue their use and delete them immediately
11-174-17R
This bulletin announces the availability of reprogramming files to optimize the ECM and address the following customer concerns: ? Check Engine light coming on (with DTC P05A0 stored in memory). ? Potential battery discharge (dead battery) after repeated periods of short-trip driving. ? A high (or ?hanging?) engine RPM after depressing the clutch pedal (Forester only).
02-170-17
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. The new seal will eliminate potential oil seepage into the wire harness connector portion of the valve. If oil seeps into the connector, over time, the Check Engine lamp may illuminate and set various AVCS-related DTCs.
10-83-15R
Models with Manual HVAC Systems only. This Service Information bulletin provides precautions to use when removing the HVAC control panel to prevent damaging the blower fan speed switch. When removing the control panel, if the fan speed switch wiring harness is pulled taught or becomes stressed, the switch may be damaged. If the connector (lower) portion of the switch becomes separated from the switch body even slightly (see Fig. 1 on page 2), the HVAC control panel assembly must be replaced. The switch itself is not serviceable. The related instrument panel (IP) wiring harness must also be inspected and replaced if any damage is confirmed. NOTE: For 2012MY Impreza, see TSB 10-78-12, dated 4/18/2012.
04-18-17
MODELS WITH EYESIGHT ONLY. This bulletin announces availability of a new Electronic Power Steering (EPS) controller to address a very limited number of cases involving DTC B281C "INCOMPATIBLE WITH EYESIGHT (EPS)" in the EyeSight system.
02-166-17R
This bulletin outlines design changes made to the upper oil pan assembly on FA and FB engines used on the models listed above. There have been isolated cases where the sealer used between the upper oil pan and the crankcase has become displaced resulting in engine oil seepage. Revisions made to the upper oil pan casting: * The mating flange thickness of the casting in the area identified as the cause for the seepage has been increased by 5.5mm. (See images provided in the Parts Information section below.) This thickness increase creates the need for a longer bolt to provide proper tightening and retention. * An additional mounting point has been added to the ribbing inside the casting to increase retention of the steel baffle plate and eliminate vibration.
07-118-17R
Models with SRVD Only. This bulletin provides revised diagnostic and repair procedures to address DTC B2327 for the Subaru Rear Vehicle Detection (SRVD), Blind-Spot Detection (BSD) and Rear Cross Traffic Alert (RCTA) system on the applicable models listed above. Under very specific (rare) conditions, the radar function of the SRVD system may experience a communication error and cause the SRVD warning lamp to illuminate. In addition, under certain highway driving conditions, an improper signal calculation by the system may cause a Cancel Code B2328 to set which will also cause the SRVD warning lamp to illuminate.
11-175-17
This bulletin announces the availability of reprogramming files to optimize the ECM and address the following customer concerns: * Engine RPM surge on light acceleration caused by improper EGR operation * Potential battery discharge (dead battery) after repeated periods of short-trip driving.
02-168-17
This Service Information bulletin announces a material change to the engine accessory drive / v-belt made to address customer concerns of a slipping belt (squeal or chirping) sound.
11-173-17
This bulletin announces availability of ECM reprogramming files designed to optimize the ECM for improving HVAC blower fan speed control. There have been a limited number of cases with reports describing the blower fan speed fluctuating / changing without input from the customer when the blower is set to maximum speed.
04-16-17
This bulletin announces availability of a new steering wheel designed to address a possible customer concern of insufficient performance of the heated steering wheel feature on applicable models.
15-196-16R
ONLY 2016-2017MY: Those Models equipped with STARLINK Telematics. Provisioning is the process by which the DCM receives the subscription request and activates the related DCM features requested as outlined in the specific subscription contract. If provisioning is not successful then the DCM may remain in an inactive state and the requested services may not be activated for the customer. Field investigation has found that this may be a result of three possible conditions. * The DCM may be off the network due to vehicle storage or other network factors. * The DCM may be lacking power or ground due to some body side electrical concern. * The DCM may have an internal failure.
02-166-17
This bulletin outlines design changes made to the upper oil pan assembly on FA and FB engines used on the models listed above. There have been isolated cases where the sealer used between the upper oil pan and the crankcase has become displaced resulting in engine oil seepage.
096516R
REVISED. This bulletin announces a design change of the fuel injector used on 2.0L DIT models to prevent water intrusion. A new silicone rubber cover has been developed and incorporated into production for this purpose.
09-65-16
This bulletin announces a design change of the fuel injector used on 2.0L DIT models to prevent water intrusion. A new silicone rubber cover has been developed and incorporated into production for this purpose.
09-64-16
This Service Information bulletin announces a change to the shape of the rubber cap used on the flange nuts securing the sub-level sending unit to the fuel tank. In addition, two of the caps are now used in production instead of only one. This change was made to enhance productivity during vehicle assembly.
16-103-16
Only Models Equipped with TR690 CVT only. This bulletin has been developed in response to a small number of customer concerns regarding fluid seepage found coming from the CVT assembly. Investigation has identified a likely source of the seepage to be the sealant used on the CVT's oil pump chain cover. The repair involves removal, a thorough cleaning and inspection of the sealing surfaces followed by re-sealing the cover.
15-205-16
This bulletin announces new reprogramming file availability and the software installation procedure to address additional operational concerns received from the field and listed below involving ?Gen 2? F10 Navigation and Display Audio units with 7? display. The procedure will involve downloading the applicable software update files from Subarunet then loading them onto a flash drive for audio unit installation. It is important to read through and understand this information completely before proceeding. These latest software updates contain new logic to address the following concerns: ? Mirrorlink 1.1 updates ? Enable Mute function for Navigation guidance ? Incomplete display of intersection names in combination meter ? Increased accuracy of the XM Traffic information displayed ? Intermittent delay (approximately 1 minute) in display of map information after initial start-up of Navigation function (2015MY Legacy and Outback only).
11-169-16
Turbo models only. This bulletin announces the availability of reprogramming files to optimize the ECM. These new files will address customer concerns of: ? Spark knock (ping) during high intake air temperature operation ? Surge on acceleration due to phantom knock detection ? Check Engine light illumination resulting from DTC P2270 and / or DTC P2270 and / or P0137 being stored in the ECM memory.
11-168-16
This bulletin announces the availability of reprogramming files to optimize the ECM. These new files will address customer concerns of Check Engine light illumination resulting from DTC P013F or P014B* being stored in the ECM memory. *DTC P014B is applicable to 3.6L models only.
12-209-16
This bulletin announces a design change to the front speaker grille. The new grilles have increased retention capabilities to address customer concerns of a loose fit.
15-204-16
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. The exchange program policy can also be found in Sections 8.4.9 and 11.2.10 of your Claims Policies and Procedures Manual found in Subarunet.
WTJ70
This announcement supersedes the announcement previously posted August 30, 2016. In the interest of customer satisfaction, Subaru of America, Inc. is initiating a service program for certain 2017 model year Forester non?Turbo vehicles with CVT. Description: The CVT fluid in affected vehicles was not filled to the proper specified level at the factory. The condition could cause a noticeable air vacuum noise or possibly even chain slip under high levels of shock load depending upon driving conditions (i.e. rapid acceleration or hill climbing). Extended driving under this low?fill condition is not recommended.
WTJ-70A
(non-Turbo) with CVT. Subaru of America, Inc. (Subaru) is initiating a Service Campaign for certain 2017 model year Forester normally aspirated vehicles with CVT transmissions. Subaru has determined vehicles affected by this Service Program require additional CVT fluid. The CVT fluid (CVTFII) in affected vehicles was not filled to the proper specified level at the factory. The condition could cause a noticeable air vacuum noise or possibly even chain slip under high levels of shock load depending upon driving conditions (i.e. rapid acceleration or hill climbing). Extended driving under this low-fill condition is not recommended.
WTJ-70
NON-TURBO MODELS - Subaru of America, Inc. (Subaru) has determined that certain 2017 model year Forester normally aspirated vehicles equipped with CVT transmissions will require additional CVT fluid. The CVT fluid (CVTFII) in affected vehicles was not filled to the proper specified level at the factory. The condition could cause a noticeable air vacuum noise or possibly even chain slip under high levels of shock load depending upon driving conditions (i.e. rapid acceleration or hill climbing).
078815R
This Service Information bulletin provides a procedure to use when installing a SOA821B200 replacement battery in a 2015MY WRX (2.0L). The sensor located on the battery ground terminal interferes with the battery vent cap used on the replacement battery.
139916R
Various paint manufacturers designate their own stock numbers and coding information although many of the major suppliers are now using the SOA paint codes to help eliminate possible confusion. Their color formulations are updated on a continual basis. Some vendors may have different color names than those provided to them by SOA. Be sure to double-check the codes and formulas beforehand to help insure an accurate color match. Should discrepancies arise, please refer your Body Shop contact inquiries to the specific paint vendor or their jobber/supplier for the most updated formula information.
1818816
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes. We advise you to always refer to the STIS web site when looking for the latest Service information. Printed pages will not be made available to update printed Service Manuals.
216316
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. The applicable Service Manuals will be revised with this new information in the near future.
01-174-16
This Service Information bulletin provides a guideline to use for placement of required or mandated windshield stickers (inside and / or outside) on vehicles equipped with EyeSight Driver Assist Technology and High Beam Assist (HBA) features. Examples of these types of stickers include: * Government facility / Military base access stickers * State-mandated Vehicle Safety Inspection and Emission Compliance stickers * Parking Permit Stickers The cameras used by both of these features require a clear, unobstructed "view" through the windshield for their proper operation. The illustration below shows the "Prohibited area" in gray. Any stickers mandated to be placed within the Prohibited area should be placed to the right of the EyeSight stereo camera and HBA camera, outside of the Prohibited area as shown in the illustration below. Viewed from inside the vehicle, the left edge of the sticker must be placed no more than 14 inches (slightly less is preferred as a "cushion" for measuring variation) from the right edge of the windshield as shown in the illustration and indicated by the box outlined in blue. Always consult state and local regulations applicable to windshield sticker placement.
0116809R
Replacement Key and Immobilizer Info
0213212R
Diagnosis and Repair for AVCS-Related DTCs
171713R
Event Data Recorder (EDR) Function of Airbag Module
Announcements-2
Effective with all 2015 model year cars and forward, the oil change interval is changing to 6,000 miles or 6 months, whichever comes first.
037012R-1
Repair Procedure for High-Pitched Sound from Extension Housing Area Using Latest Generation Production Parts
037012R
This Bulletin provides production change, repair procedure and parts information to address a customer concern of a high-pitched sound coming from the transmission extension housing area.
0214013
Oil Filler Cap Gasket Coming Unseated
171713
Event Data Recorder (EDR) Function of Airbag Module
WQE41-1
Puddle Light Recall
037012
Repair Procedure for High-Pitched Sound from Extension Housing Area Using Latest Generation Production Parts
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.