Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
15-308-23R
This Service Information Bulletin outlines a systematic procedure for diagnosing parasitic draw (dark/standby current) in vehicles experiencing battery drain when the ignition is off, leading to no-start conditions or frequent jump-starts.This is an revised version of the original bulletin.
16-156-25R
This bulletin announces a design change made to the CVT Control Valve Body. The updated valve body incorporates an enhanced valve sleeve to improve durability. This is an revised version of the original bulletin.
15-304-22R
This Bulletin has been developed to outline the steps for gathering basic but essential information during diagnosis of Infotainment concerns. (This is an revised version of the original bulletin.)
Article Locator
Techtips newsletter locator index.
15-333-25R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. This is an revised version of the original bulletin
SubaruNet Annoucement (E
This announcement is requesting retailer staff to retain the EyeSight protective hood covers from Generation 4 EyeSight cameras.
01-167-08R
This bulletin contains additional information for recommended materials listed in the Service Manuals for individual models.
SubaruNet Announcement (R
This announcement provides information on the remanufactured CVT transmission program.
07-240-26R
This Service Information Bulletin was developed to provide interim guidance for vehicles exhibiting DTC B2A20.
03-97-26
This bulletin announces the service manual correction regarding clutch master cylinder reservoir service procedures.
05-97-26
This Bulletin provides the diagnostic procedures to be followed when addressing customer concerns of steering wheel/vehicle body vibration when driving at highway speeds when tire/wheel balance is suspected.
10-105-25R
This bulletin announces the new procedure and Warranty Fail Code for FirstTime air conditioning (A/C) performance concerns possibly resulting from an undetected A/C refrigerant leak.
15-219-18R
This bulletin contains information to help when attempting to complete the STARLINK Telematics subscription process, an Error Code 202 and / or 204 may occur preventing the process from completing successfully
SubaruNet Announcement (A
This announcement provides information on the use of aftermarket services or tools for programming immobilizer keys/fobs.
Subaru Tech Tips Special
This Subaru service and technical support line newsletter provides information on the next phase of TechShare.
15-300-22R
This Bulletin provides the diagnostic procedure for the STARLINK® Remote Engine Start (RES).
Subarunet Announcement (E
This announcement has been created to address difficulties with software updates on Subaru Select Monitors with DST-010 interface firmware has been updated.
18-226-25R
This Service Information Bulletin provides the Service Manual Correction to the diagnostic procedure for DTC B2A16 (Immobilizer Key Collation Diagnosis).
15-333-25
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
Subaru Tech Tips (Article
Subaru service article locator.
15-130-08R
This bulletin provides information on the load carrying capacity reduced label when a port-installed or retailer-installed accessory exeeds 1.5 percent of the GVWR or 100 pounds, which ever is lower.
07-233-25R
This Bulletin provides details on a new formal testing, charging, and tracking procedure for all 12-volt batteries in new vehicle inventory.
07-236-25
This Bulletin outlines a comprehensive update to the dark current/parasitic draw diagnosis & testing procedures.
16-156-25
This bulletin announces a design change made to the CVT Control Valve Body. The updated valve body incorporates an enhanced valve sleeve to improve durability.
07-233-25
This Bulletin provides details on a new formal testing, charging, and tracking procedure for all 12-volt batteries in new vehicle inventory wjhich must be tested and reported every 30 days.
15-266-20R
This Bulletin provides helpful procedures and best practices to utilize when customers present with concerns relating to the operation of their Gen 2/Gen 3 Telematics system equipped Subaru.
15-320-24R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
SubaruNet Announcement
Subaru of America, Inc. will release an OTA to perform a software update to the DCM. This is a preventive OTA.
13-108-25
This bulletin provides information on paint codes for vehicles in the 2026 line up.
Subaru Service Technical
Subaru Service Technical Support Newsletter special edition.
SubaruNet Annoucement
This announcment provides information on the release of the latest software updates to the Subaru Midtronics DSS-5000 Battery Diagnostic tool.
15-251-19R
This Bulletin provides additional diagnostics to follow when addressing a Telematics-related DTC B2A16.
SubaruNet Announcement (S
This announcement is to bring attention to the OTA for In-vehicle service appointment scheduler and In-vehicle message center.
01-168-09R
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site.
02-192-24R
This Bulletin announces the diagnostic procedures to be followed when diagnosing engine oil leakage on FA and FB type engines.
14-31-25
This Bulletin announces availability of a User Guide and an informative video to supplement the recent releases to retailers of the SOA321152 and SOA321153 Terminal Test Kits.
09-51-08R
The purpose of this bulletin is to advise of SOA’s revised Catalytic Converter Recycling Program shipping procedure.
16-103-16R
This bulletin has been developed in response to a small number of customer concerns regarding fluid seepage found coming from the CVT assembly.
Subarunet Announcement
This announcement is in regard to special service tool shipment will be shipped directly to the Subar retailers during February.
RC5 Head Unit OTA
A head unit OTA will be available via cellular network for Mid and High Grade CP1.5 head units.
07-59-07R
This bulletin is for information purposes only.The bulletin adresses design changes of the headlamps and rear combination lamps, where moisture and or condensation may develop on the inside of the lamp lenses.
15-298-22R
This Service Information Bulletin announces the preferred practices to be used when handling vehicles equipped with Gen2 Telematics which are enrolled in the Subaru STARLINK® Security Plus Service featuring Stolen Vehicle Recovery Plus with Immobilizer.
02-192-24
This Service Information Bulletin announces the diagnostic procedures to be followed when diagnosing engine oil leakage on FA and FB type engines.
07-178-21R
This Service Information bulletin is being released as guidance for proper testing and charging of vehicle batteries.
15-320-24
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
02-191-22R
This bulletin announces availability of the NEW genuine Subaru engine oil filter.
03-94-24
This bulletin outlines the judgment criteria to be used when inspecting front transverse link bushings to reduce unnecessary bushing replacement.
Thermo Control Valve Vide
This thermo control valve video contains information on the replacement of thermo control valve.
13-107-24
This Bulletin provides SOA paint codes to help eliminate possible confusion for 2025 MY vehicles.
05-91-24
This Bulletin provides guidance for diagnosing a leaking front or rear suspension strut.
06-90-24
This bulletin provides diagnosis and procedure information to be applied when diagnosing potential fluid leaks on front and rear brake calipers. This information has been developed to reduce unnecessary brake caliper replacement.
16-112-18R
This bulletin announces a design change to the CVT select lever (shifter) mechanism in response to isolated customer concerns of not being able to remove the key from the ignition switch when the vehicle is in Park.
12-249-23R
This bulletin announces the recommended cleaning procedures to followed when encountering vehicles with long time exposure to pollen on painted surfaces on vehicles imported from Japan. This bulletin does not apply to SIA built vehicles.
02-131-12R
The purpose of this Bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the timing chain cover, front camshaft cap, camshaft carrier and / or upper oil pan.
16-131-20R
This Service Information Bulletin provides an updated diagnostic flow along with an IMPORTANT caution to follow for certain CVT solenoid related DTCs as listed.
18-230-22
The purpose of this bulletin is to provide a description of current changes to Service Manuals.
15-302-22
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
Subaru Tech Tips
Special Edition, 2012 current model subaru evaporative diagnostics and smoke testing.
12-288-20R
This bulletin announces a design change made to the Slide Rail components of the left and right front power seat frame / track assembliesd.
12-203-16R
This bulletin provides a procedure to address customer concerns of a squeaking sound originating from where the front seat belt buckle assembly attaches to the seat frame.
18-219-22
This bulletin announces the Service Manual correction for the diagnostic trouble tree for DTC C2521 and/or DTC 21.
18-222-22
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
15-192-22R
This bulletin has been developed to outline the steps for gathering basic essential information during diagnosis and repair of the Infotainment concerns. (Applicable to all models with Harman or Denso CP1 Infotainment).
06-85-22
This bulletin announces the design change of the rear stabilizer bar.
02-189-22
This Bulletin announces design changes to the engine oil and CVT fluid drain plugs.
Subarunet Announ
(Subaru Retailers) As part of Subaruâs dedication to customer satisfaction, Subaru of America, Inc. (SOA) is announcing an extension to the Basic New Car Limited Warranty for the CVT Parking Switch for certain 2015-2018 MY Legacy, Outback, 2012-2018 MY Impreza, 2013-2018 MY Crosstrek, 2015-2018 MY WRX and 2014-2018MY Forester vehicles.
02-188-21
This bulletin announces an additional service procedure for timing chain and / or cam sprocket replacement on FA and FB type engines.
18-214-21
This bulletin provides a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
04-27-21R
As part of Subaruâs dedication to customer satisfaction, Subaru of America, Inc. (SOA) is announcingan extension to the Basic New Car Limited Warranty for the Electronic Power Steering (EPS) GearBox Assembly for certain 2012-2018 MY vehicles.
Subaru Owner Let
As part of Subaru of Americaâs dedication to customer satisfaction, this letter is to inform you of an extension to the Basic New Car Limited Warranty for your vehicleâs Electronic Power Steering Gear Box Assembly.
02-187-21
This bulletin outlines changes in the service procedure for engine oil pressure inspection.
18-209-21
Description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
02-157-14R
As part of our dedication to customer satisfaction, Subaru of America, Inc. is initiating a program to extend the original New Car Powertrain Limited Warranty coverage for excessive engine oil consumption on applicable vehicles to 8 years / 100,000 miles from the original warranty start date.
05-76-20R
This bulletin announces availability of new front wheel hub assemblies incorporating bearing surfaces having increased resistance to imperfections resulting from shock loads.
02-169-17
This Service Information bulletin outlines an enhancement made to the 2.0L cylinder head casting part numbers provided below.
06-59-17R
This Service Information bulletin announces availability of a new front brake pad shim kit to specifically address customer concerns of a squeaking or squealing sound on the models listed above.
12-224-17R
This bulletin provides a procedure for replacement of the black foam rubber insulating cushions for the roof rails.
14-22-16R
To help reduce confusion and increase technician efficiency, Subaru of America, Inc. (SOA) has developed the following cross reference list to help locate the appropriate Special Service Tool.
16-107-17R
In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Powertrain Warranty coverage for the Continuously Variable Transmission (CVT) on the above listed models and model years from the original five (5) years or sixty thousand (60,000) miles (whichever comes first) to ten (10) years or one-hundred thousand (100,000) miles (whichever comes first).
12-308-21
This bulletin announces a design change made to the front seat hinge bolts.
03-82-18R
This bulletin announces a design change to the clutch release bearing.
05-70-19R
This bulletin announces a design change made to the rear wheel / brake backing plates.
16-131-20
This Service Information Bulletin provides corrected diagnostics containing a revised flow for certain CVT solenoid related DTCs.
10-19-20
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
12-301-20
This bulletin outlines changes made to the rear shelf trim to address customer concerns of a rattling sound heard while driving over bumpy / rough roads.
18-201-20
The purpose of this bulletin is to provide a desription of current changes to service manuals available via the Subaru Technical Information System (STIS) web site.
05-76-20
This bulletin announces availability of new front wheel hub assemblies incorporating bearing surfaces having increased resistance to imperfections resulting from shock loads.
06-79-20
This bulletin announces availability of new master cylinder application shaft seals.
WTY-84R
Subaru of America, Inc. (Subaru) is recalling certain 2013 model year BRZ and XV Crosstrek and 2012-2014 model year Impreza vehicles to replace the engine valve springs which may fracture. A total of 139,324 U.S. vehicles will be affected by this recall.
12-288-20
This bulletin announces a design change made to the Slide Rail components of the left and right front power seat frame / track assemblies used on the models listed.
14-25-20
This service information bulletin announces availability of enhanced service parts to repair and optimize durability of the valve spring replacement (installer) tools used to perform the WTY-84 recall.
01-181-20
All Models (Vehicle Cleaning- COVID-19Best Practices)
14-24-20
This service information bulletin outlines a procedure for Subaru Special Tool Kit number J-53014.
17-17-13R
This bulletin provides information regarding Event Data Recorder (EDR) functionality which has been incorporated into the airbag system.
18-199-20
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
07-169-20
This Service Information bulletin describes a change made to the labels applied to the push to start switches used on the models listed.
07-152-19R
This bulletin announces availability of new power window switch assemblies.
10-96-19
This bulletin announces availability of a new HVAC blower motor unit assemblies developed to address isolated concerns of the blower motor becoming inoperative. If this issues occurs on models with Auto A/C, the blower fan may become totally inoperative. If this issue occurs on models with Manual A/C, the blower fan may operate on high speed only. The root cause of these conditions is water intrusion into the blower motor causing rust and corrosion to develop. Over time, the blower motor may begin to draw more electrical current to operate. if that occurs, the additional draw can cause the related fuse and/ or blower resistor to fail. To address this condition, additional packing has been added to improve sealing of the blower unit case along with development of a new style cabin air filter which also in corporates improved sealing.
WUE-90R
Subaru of America, Inc. (Subaru) is recalling certain Crosstrek, Forester, Impreza, and WRX vehicles to replace the brake lamp switch. A total of 1,303,530 U.S. vehicles will be affected by this recall.
05-70-19
This bulletin announces a design change made to the rear wheel / brake backing plates. Under certain circumstances, some customers may have a concern regarding a howling-type sound from the rear of the vehicle later diagnosed as a faulty hub / bearing assembly. Unevenness of the backing plate surfaces may affect the concentricity (roundness) of the hub / bearing after torqued during assembly and over time, cause the howling -type sound to develop. Production changes for the backing plates have been implemented to optimize their mounting surface quality.
06-51-15R
This bulletin announces availability of a new front disc brake pad, shim, grease and clip kit designed to reduce customer concerns of excessive brake squeal. This new kit eliminates the âslottedâ shim which previously was installed between the rubber-coated outer shim and the brake pad.
06-68-19R
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. This will prevent the pad from dragging due to corrosion buildup which may result in uneven or premature wear of the replacement brake pads. This additional instruction applies to all models with brake pads using the upper and lower pad clips and has been added to the brake pad installation procedures found in the related Service Manuals.
WUE-90 tool
SOA has received multiple requests for additional 83399Fj000rt BRAKE LIGHT SWITCH tools and now has sufficient stock to allow retailers to place orders for single tools.
02-163-16R
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. The applicable Service Manuals will be revised with this new information in the near future.
07-152-19
This bulletin announces availability of new power window switch assemblies developed to address the following customer concerns: ? Power windows inoperative from the driver?s door master and / or passenger front door switch ? Unable to remotely operate other door windows from the driver?s door master switch ? One-Touch Auto Up / Down features inoperative from either / both front door switches
WUF-91R
Subaru of America, Inc. (Subaru) is recalling certain vehicles in the ranges listed below to inspect and potentially replace the ignition switch. A total of 511 U.S. vehicles will be affected by this recall.
02-170-17R
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. The new seal will eliminate potential oil seepage into the wire harness connector portion of the valve. If oil seeps into the connector, over time, the Check Engine lamp may illuminate and set various AVCS-related DTCs.
WUE-90
Subaru of America, Inc. (Subaru) is recalling certain Crosstrek, Forester, Impreza, and WRX vehicles to replace the brake lamp switch. A total of 1,303,530 U.S. vehicles will be affected by this recall.
02-178-18R
This Service Information bulletin announces a design change made to the rubber timing hole access plug to improve its retention and prevent water intrusion into the converter case.
02-134-12R
The purpose of this bulletin is to announce a change to the specification of the valve springs used in the FB engine. The new springs have different color paint marks to help identify their application.
16-119-19
This Service Information bulletin announces availability of a new control valve assembly (valve body) designed to prevent false detection of DTC P0841 and / or illumination of the AT Temp light. Testing has revealed in some limited cases, air bubbles (aerated fluid) may enter certain pressure circuits within the control valve assembly causing fluid pressure control and adjustment to be calculated incorrectly resulting in DTC P0841. The shape of these circuits has been changed to prevent this occurrence.
11-186-18
This bulletin announces availability of reprogramming files to optimize the ECM. These files enhance detection of DTC P0300: RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED. If a customer presents with a rough idle concern and / or hesitation after a cold start when using winter-blend fuels, reprogram the ECM following the normal FlashWrite procedure. The new logic contains revised A/F, ignition timing and alternator controls designed to prevent an over-lean fuel mixture condition at cold start and stabilize the engine idle.
04-13-14R
IMPORTANT: This Service Bulletin has been as been replaced by TSB 04-24-18 dated 11/9/2018 entitled ?Increased Steering Effort when Cold, DTC C2532?. Please refer to this new bulletin for the latest information regarding this condition.
07-133-18
This Service Information Bulletin announces design changes to the engine?s knock sensor which will help improve vehicle assembly line efficiency and increase durability. In some cases, the Check Engine light may illuminate and a knock sensor-related DTC set in the ECM memory: P0327, P0328, P0332 and P0333. The knock sensor for DIT engines is now utilized for NA engines to improve durability and resistance to heat.
04-24-18
This bulletin announces a new Electronic Power Steering (EPS) control module for the models listed above. These new EPS control modules address a limited number of customer concerns regarding increased steering effort which may occur during freezing temperatures after a cold start. The cause has been identified as a frozen relay contact inside the control module. Illumination of the EPS warning lamp can also occur and a DTC C2532 may be stored.
03-82-18
This Service Information bulletin announces a design change to the clutch release bearing used on the models as listed above. During assembly of the bearing, a different type of grease is used which has a higher resistance to heat. In cases where the operator keeps a foot on the clutch pedal for extended periods, an increased amount of heat is generated which can cause the grease inside the bearing to deteriorate. In a case of prolonged clutch pedal application, seizure of the bearing can occur with potential damage to other related components.
12-251-18
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully.There is a latch to keep the glove box closed on both sides of the glove box door. If the door is closed without using enough force to engage both latches or by pushing it shut on just one side instead of in the middle, one may close and not the other. Over time, if the door is not fully closed with both latches, high cabin temperatures along with weight of the items inside the glove box may cause the assembly to deform slightly and a gap to develop.
10-86-17R
A design change was made to the blower motor assembly to address the following customer concerns: ? Blower fan is either inoperative or only operates on high speed. ? Excessive rotational-type sound heard when the fan is operating.
07-128-18R
This Service Information bulletin provides a measurement and adjustment procedure for the stop lamp switch. An improperly adjusted (or faulty) stop lamp switch can cause any of the DTCs listed above to set and result in the related system?s warning lamp to illuminate.
18-194-18
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes. We advise you to always refer to the STIS web site when looking for the latest Service information
02-177-18
In conjunction with the launch of our new Remanufactured FB Engine Short Block Program, SOA would like to reinforce Core Return Policy (See Parts Policy & Procedures Manual ? Section 12.3 Core Returns ? Reman) and provide suggestions for removal and handling of the short block.
07-138-18
This Service Information bulletin announces the standardization of the IG2 and ACC relays used on the models listed. Both of these relays are located on the back (front facing) side of the passenger compartment fuse box (F/B).
12-234-18
This bulletin provides a repair procedure for replacing the foam cushion installed between the top front edge of the IP and the windshield glass. Use the supplied Service Procedure to address a customer concern involving the foam cushion becoming visible above the IP near the defroster vent outlets.
04-21-18
This bulletin announces availability of a new Electronic Power Steering (EPS) gear box assembly designed to address a VERY limited number of customer concerns regarding uneven steering effort felt when turning left or right. In areas where high concentrations of road salt are used to melt ice and snow, corrosion may develop and cause a portion of the gear box housing to crack if the vehicle were to suffer a large enough impact from hitting a pothole or similar type of road hazard.
15-222-18
This bulletin announces a design change to the A/C Condenser receiver-dryer assembly. The change involves the addition of a rubber end cap and retaining clip onto the bottom of the receiver-dryer tank portion to prevent corrosion intrusion and enhance sealing.
18-193-18
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes. We advise you to always refer to the STIS web site when looking for the latest Service information. Printed pages will not be made available to update printed Service Manuals.
12-238-18R
This bulletin announces a design change to the front door checkers used on the models listed. The new checker mechanism provides a more ?positive feel? of the detents or check positions as the front doors are opened and closed.
07-134-18
This Service Information bulletin provides a new troubleshooting chart to use when diagnosing a DTC B1760 related to the Occupant Detection System (ODS). Following these diagnostic steps will help avoid unnecessary ODS sensor / seat cushion assembly replacement
06-61-18
This bulletin announces availability of new VDC Control Module & Hydraulic Units (VDCCM&H/U) to address isolated customer concerns of the green Hill Holder light blinking and cancel warning alarm sounding during cranking / starting the engine
12-231-18R
This bulletin announces a design change to the air vent grille located in the lower portion of the trunk (or cargo) area. The shutters of the vent grille are designed to open briefly and relieve cabin pressure when the doors are shut with the windows fully closed. The vent grilles have rubber ?shutters? which occasionally, may catch on the frame (case) portion and not close properly allowing outside air / odor to enter the cabin.
12-232-18
This bulletin announces a design change to the front seat back upholstery retaining hooks (HOOK FLAT MAT). The change is in response to customer concerns of discomfort coming from the center of the seat back and outside bolsters. When a hook fails, the center (flat) portion of the seat back drops inward from lack of support. If not repaired, with continued use, the seat back frame may break down the foam padding covering it. Eventually, the frame will likely wear through and damage the trim cover.
12-231-18
( 2017-2018MY Impreza - 5 Dr Only)
06-55-16R
EXCLUDES HYBRID MODELS. This bulletin announces a design change to the brake light switch (BLS) to reduce the possibility of improper illumination of the ABS and/or VDC warning lamp. In the event a product containing silicone is used to lubricate the BLS or for other purposes in the area around the switch, a non-conductive coating may develop over time on the internal electrical contacts and affect operation of the switch. On / Off signal output from the BLS is critical for proper operation of various systems on the vehicle. When the switch does not operate properly, warning lamps illuminate and DTCs are stored. A table with BLS-related DTCs and additional information is provided in the Service Procedure information. A photo of the switch changes is shown below. This bulletin also provides a diagnostic and adjustment procedure to be used when diagnosing brake light switch-related DTCs.
07-119-17R
This Service Information bulletin announces a production method change to the rear combination lamp assembly. The application procedure of the anti-fog coating was changed to prevent a customer concern of visible drip marks (or streaks) appearing on the inside of the lamp lens.
02-170-17
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. The new seal will eliminate potential oil seepage into the wire harness connector portion of the valve. If oil seeps into the connector, over time, the Check Engine lamp may illuminate and set various AVCS-related DTCs.
10-83-15R
Models with Manual HVAC Systems only. This Service Information bulletin provides precautions to use when removing the HVAC control panel to prevent damaging the blower fan speed switch. When removing the control panel, if the fan speed switch wiring harness is pulled taught or becomes stressed, the switch may be damaged. If the connector (lower) portion of the switch becomes separated from the switch body even slightly (see Fig. 1 on page 2), the HVAC control panel assembly must be replaced. The switch itself is not serviceable. The related instrument panel (IP) wiring harness must also be inspected and replaced if any damage is confirmed. NOTE: For 2012MY Impreza, see TSB 10-78-12, dated 4/18/2012.
15-168-13R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. The exchange program policy can also be found in Sections 8.4.9 and 11.2.10 of your Service Policies and Procedures Manual found in subarunet.
WTM-73R
Subaru of America, Inc. (Subaru) is recalling 100,127 vehicles including certain 2007-2009 model year Legacy and Outback (turbo models only), 2008-2014 model year Impreza (turbo models only) and 2009-2013 model year Forester (turbo models only) vehicles to replace the secondary air pump relay.
07-119-17
This Service Information bulletin announces a production method change to the rear combination lamp assembly. The application procedure of the anti-fog coating was changed to prevent a customer concern of visible drip marks (or streaks) appearing on the inside of the lamp lens.
02-166-17R
This bulletin outlines design changes made to the upper oil pan assembly on FA and FB engines used on the models listed above. There have been isolated cases where the sealer used between the upper oil pan and the crankcase has become displaced resulting in engine oil seepage. Revisions made to the upper oil pan casting: * The mating flange thickness of the casting in the area identified as the cause for the seepage has been increased by 5.5mm. (See images provided in the Parts Information section below.) This thickness increase creates the need for a longer bolt to provide proper tightening and retention. * An additional mounting point has been added to the ribbing inside the casting to increase retention of the steel baffle plate and eliminate vibration.
16-107-17
CVT MODELS ONLY. In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Powertrain Warranty coverage for the Continuously Variable Transmission (CVT) on the above listed models and model years from the original five (5) years or sixty thousand (60,000) miles (whichever comes first) to ten (10) years or one-hundred thousand (100,000) miles (whichever comes first). This change is not in response to any specific condition, rather it is to provide customers with added assurance regarding the function and overall performance of their CVT. Additionally, vehicles which are more than ten (10) years old or beyond one-hundred thousand (100,000) miles at the time customer notification letters are mailed are being offered additional coverage for a period of one-year from the date of the customer notification letters. A copy of the customer letter is attached to this bulletin as reference.
02-168-17
This Service Information bulletin announces a material change to the engine accessory drive / v-belt made to address customer concerns of a slipping belt (squeal or chirping) sound.
02-166-17
This bulletin outlines design changes made to the upper oil pan assembly on FA and FB engines used on the models listed above. There have been isolated cases where the sealer used between the upper oil pan and the crankcase has become displaced resulting in engine oil seepage.
1221717
This bulletin announces a design change made to the front seat outer hinge cover trim panels. In some cases, when exiting the vehicle, the trim panel may inadvertently get kicked and become dislodged from the seat cushion assembly. The shape of the front portion of the panel has been changed to prevent this condition.
02-164-16
This Service Information bulletin announces a design change to the internal contact portion of the oil pressure switch to increase durability
09-64-16
This Service Information bulletin announces a change to the shape of the rubber cap used on the flange nuts securing the sub-level sending unit to the fuel tank. In addition, two of the caps are now used in production instead of only one. This change was made to enhance productivity during vehicle assembly.
15-193-16R
All 2012 to 2015 Models Equipped with Fujitsu Ten (F10) Generation 1 (Gen1) Audio / Navigation Systems. This bulletin announces a new procedure for updating the operating software used in F10 Gen1 audio / navigation systems. This new procedure eliminates the need to exchange the head unit / SD card to obtain software-related updates and operating enhancements.
12-189-15R
This bulletin provides information about changes made to the rear shelf trim to address customer concerns of a rattling sound heard while driving over bumpy / rough roads. The sources of the rattle have been identified as: ? the mounting points for the center stop lamp where it fits into the package shelf ? the package shelf itself rattling against the inside of the rear glass ? the rib and/or stand portions located on the underside of the package shelf contacting the shelf portion of the vehicle body.
12-207-16
This bulletin announces a change to the procedure used in production of the rear door glass assembly. The bottom edge of the door glass is pressed into a metal channel lined with rubber. The channel attaches the door glass assembly to the window regulator. In below-freezing temperature conditions, water freezing in the channel combined with the door glass sticking to the door weatherstrip can increase chance of the glass separating from the channel when attempting to operate (lower) the window. A lubricant has been added to the rubber portion to insure the glass gets fully seated during assembly which maximizes the clamping force of the channel on the glass.
216316
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. The applicable Service Manuals will be revised with this new information in the near future.
12-206-16
All Models Listed with Seat Lifter Feature. This bulletin provides a procedure to address a customer reported cosmetic condition of surface rust appearing on the inner seat cushion frame of the front seat assemblies.
12-203-16
This bulletin provides a procedure to address customer concerns of a squeaking sound originating from where the front seat belt buckle assembly attaches to the seat frame. A design change was made to the wave washer used at the attachment point to eliminate the sound. The sound can be heard when moving the buckle assembly side to side.
16-102-16
TSB: All Models Equipped with CVT Transmissions. This Service Information bulletin provides a new flow chart and additional diagnostic tools to assist Technicians with troubleshooting DTC P0841- SECONDARY OIL PRESSURE SENSOR PERFORMANCE.
10-84-16R
This bulletin announces the availability of a new Air Conditioning compressor / clutch assembly to address customer concerns of the system not operating. Electrical windings located inside the clutch assembly have been changed to eliminate the condition. The service procedure will involve replacement of the A/C compressor and clutch as a complete assembly.
15-201-16
This Service Information bulletin announces a design change to the retractable portion of the tonneau cover made to address customer concerns of the cover retracting on its own while driving on rough roads. The shape and length (an additional 1mm) of the stoppers on both ends of the brace which secure the cover when in use have been changed as shown in the illustration below.
18-186-16
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes.
02-157-14R-4-28-
Revised TSB. As part of our dedication to customer satisfaction, Subaru of America, Inc. is initiating a program to extend the original New Car Powertrain Limited Warranty coverage for excessive engine oil consumption on applicable vehicles to 8 years / 100,000 miles from the original warranty start date.
02-157-14N
Oil Consumption Class Action Claim Notice Clarification VIN break point clarification Memo. Recently SOA has become aware of some retailer questions regarding the VIN breakpoint information supplied as part of the class action notice.
122663
Remote Engine Start Systems Trouble Shooting Guide
12-182-15R
This bulletin announces availability of a new front door checker mechanism designed to hold the doors more securely when they are in partially open / closed positions. An additional detent position has also been added.
02-157-14FAQ
Oil Consumption Class Action Law Suit Frequently Asked Questions
10-84-16
This bulletin announces the availability of a new Air Conditioning compressor / clutch assembly to address customer concerns of the system not operating. Electrical windings located inside the clutch assembly have been changed to eliminate the condition. The service procedure will involve replacement of the A/C compressor and clutch as a complete assembly.
02-157-14R-4-13-
Revised TSB. As part of our dedication to customer satisfaction, Subaru of America, Inc. is initiating a program to extend the original New Car Powertrain Limited Warranty coverage for excessive engine oil consumption on applicable vehicles to 8 years / 100,000 miles from the original warranty start date.
05-61-16
This bulletin announces a design change to the front strut mounts intended to address customer concerns of a popping-type sound which may be heard when making low speed turns.
15-193-16
This bulletin announces a new procedure for updating the operating software used in F10 Gen1 audio / navigation systems. This new procedure eliminates the need to exchange the head unit / SD card to obtain software-related updates and operating enhancements. All 2012 to 2015 Models Equipped with FujitsuTen (F10) Generation 1 (Gen1) Audio / Navigation Systems
09-63-16
THIS SERVICE INFORMATION BULLETIN SERVES AS A REMINDER TO ALWAYS FOLLOW THE PROPER PROCEDURES WHEN DIAGNOSIS OF A DTC B1500 LEADS TO REPLACEMENT OF A FAULTY MAIN AND / OR SUB FUEL LEVEL SENSOR.
PEOCCAS
PROPOSED ENGINE OIL CONSUMPTION CLASS ACTION SETTLEMENT RECENTLY YOU MAY HAVE SEEN VARIOUS ONLINE AND OTHER MEDIA ARTICLES REGARDING SUBARU OF AMERICA, INC. REACHING A PROPOSED SETTLEMENT IN A CLASS ACTION LAWSUIT FOR ALLEGED OIL CONSUMPTION CONCERNS ON CERTAIN SUBARU VEHICLES. SOME MEDIA OUTLETS ALSO SUPPLIED VARYING INFORMATION ON THE CONTENTS OF THIS SETTLEMENT. THE FOLLOWING INFORMATION IS BEING PROVIDED TO YOU, OUR RETAILERS, IN ADVANCE OF ANY CUSTOMER NOTIFICATION.
0215714R
surface treatment change to oil control piston rings
12-195-15
SHOULD YOU RECEIVE A CUSTOMER CONCERN OF VIBRATION OR LOOSENESS IN EITHER OF THE DOOR MIRRORS, A DESIGN CHANGE HAS BEEN MADE TO THE 3 MIRROR HEAD MOUNTING HOLES IN THE MOUNTING BASE. IN ADDITION, A NEW RETAINING BOLT AND TIGHTENING TORQUE SPECIFICATION ARE NOW USED TO SECURE THE MIRROR HEAD TO THE MOUNTING BASE. THIS BULLETIN PROVIDES A PROCEDURE FOR REPAIRING THE EXISTING MIRROR ASSEMBLY BY REPLACING THE THREE MOUNTING SCREWS WITH UPDATED FASTENERS. NOTE: REFER TO TSB 12-152-13 DATED 6/17/2013 FOR RELATED INFORMATION ON BRZ MODELS.
10-83-15
THIS SERVICE INFORMATION BULLETIN PROVIDES PRECAUTIONS TO USE WHEN REMOVING THE HVAC CONTROL PANEL TO PREVENT DAMAGING THE BLOWER FAN SPEED SWITCH. WHEN REMOVING THE CONTROL PANEL, IF THE FAN SPEED SWITCH WIRING HARNESS IS PULLED TAUGHT OR BECOMES STRESSED, THE SWITCH MAY BE DAMAGED. IF THE CONNECTOR (LOWER) PORTION OF THE SWITCH BECOMES SEPARATED FROM THE SWITCH BODY EVEN SLIGHTLY (SEE FIG. 1 ON PAGE 2), THE HVAC CONTROL PANEL ASSEMBLY MUST BE REPLACED. THE SWITCH ITSELF IS NOT SERVICEABLE. NOTE: FOR 2012MY IMPREZA, SEE TSB 10-78-12, DATED 4/18/2012.
12-194-15
THIS BULLETIN ANNOUNCES A DESIGN CHANGE TO THE FRONT BUMPER CORNER MOUNTING BRACKET TO ADDRESS CONCERNS OF A GAP BETWEEN THE TOP EDGE OF THE COVER AND THE HEADLAMP ASSEMBLY AS SHOWN BELOW.
16-97-15
THIS BULLETIN PROVIDES A PROCEDURE FOR DIAGNOSING A CUSTOMER CONCERN OF A DELAYED AND / OR HARSH ENGAGEMENT OF THE CVT (MODEL TR580) WHEN SHIFTING INTO REVERSE OR DRIVE FROM NEUTRAL. ALL 2013-16MY, 4-CYLINDER, N/A MODELS WITH CVT
18-183-15
THE PURPOSE OF THIS BULLETIN IS TO PROVIDE A DESCRIPTION OF CURRENT CHANGES TO SERVICE MANUALS AVAILABLE VIA THE SUBARU TECHNICAL INFORMATION SYSTEM (STIS) WEB SITE. THE TABLES CONTAINED WITHIN THIS BULLETIN ARE TO BE USED AS GUIDES FOR BECOMING AWARE OF THE LATEST CHANGES. WE ADVISE YOU TO ALWAYS REFER TO THE STIS WEB SITE WHEN LOOKING FOR THE LATEST SERVICE INFORMATION. PRINTED PAGES WILL NOT BE MADE AVAILABLE TO UPDATE PRINTED SERVICE MANUALS. PAPER MANUALS MAY HAVE DIFFERENT PAGE NUMBERING THEN WHAT IS REFLECTED BELOW, BASED ON MULTIPLE NEW AND REVISED PAGES. PLEASE REFER TO THE INFORMATION CONTAINED ON THE STIS WEB SITE FOR ALL FUTURE, UPDATE SERVICE MANUAL INFORMATION.
06-51-15
THIS BULLETIN ANNOUNCES AVAILABILITY OF A NEW FRONT DISC BRAKE PAD, SHIM, GREASE AND CLIP KIT DESIGNED TO REDUCE CUSTOMER CONCERNS OF EXCESSIVE BRAKE SQUEAL. THIS NEW KIT ELIMINATES THE SLOTTED SHIM WHICH PREVIOUSLY WAS INSTALLED BETWEEN THE RUBBER-COATED OUTER SHIM AND THE BRAKE PAD.
06-46-14R
THIS BULLETIN PROVIDES A REVISED ADJUSTMENT PROCEDURE TO BE USED WHEN DIAGNOSING BRAKE LIGHT SWITCH (BLS) -RELATED DTCS C1531 AND/OR C0054. IF THE BLS IS OUT OF ADJUSTMENT, THE ABS AND/OR VDC WARNING LAMP MAY ILLUMINATE.
06-48-15R
THIS BULLETIN ANNOUNCES A DESIGN CHANGE TO THE STOP LIGHT SWITCH TO REDUCE THE POSSIBILITY OF IMPROPER ILLUMINATION OF THE ABS AND/OR VDC WARNING LAMP WITH RESULTING DTCS C1531 AND/OR C0054. DETAILS OF THE SWITCH CHANGES ARE SHOWN IN THE ILLUSTRATION BELOW.
08-39-15
THIS SERVICE INFORMATION BULLETIN PROVIDES A PROCEDURE FOR RESETTING THE LIFETIME FUEL CONSUMPTION FUNCTION OF THE MFD. WHENEVER REPLACING THE MFD AND / OR COMBINATION METER, THE LIFETIME FUEL CONSUMPTION FUNCTION OF THE MFD MUST BE RESET FOR ACCURATE INFORMATION TO DISPLAY GOING FORWARD. IF NOT RESET, ERRONEOUS VALUES (EITHER EXTREMELY HIGH IN THE CASE OF A MFD REPLACEMENT OR EXTREMELY LOW FOR A COMBINATION METER REPLACEMENT) FOR LIFETIME FUEL CONSUMPTION WILL BE DISPLAYED. THERE IS NO WAY TO TRANSFER THE OLD / EXISTING LIFETIME FUEL CONSUMPTION RESULTS TO THE NEW MFD OR COMBINATION METER ALLOWING IT TO CONTINUE UNINTERRUPTED. AS A RESULT, AFTER REPLACEMENT OF THE MFD AND / OR COMBINATION METER, ALL CALCULATIONS WILL START FRESH FOLLOWING PERFORMANCE OF THE FOLLOWING PROCEDURES.
03-67-12R
SUBARU OF AMERICA, INC. HAS EXTENDED THE AVAILABILITY OF REMANUFACTURED CVT TRANSMISSIONS TO INCLUDE CROSSTREK, FORESTER AND IMPREZA APPLICATIONS. PLEASE CHECK APPLICATIONS AND AVAILABILITY THROUGH NORMAL PARTS CHANNELS PRIOR TO MAKING VEHICLE REPAIRS. RETAILERS ARE REQUIRED TO USE A REMANUFACTURED UNIT FOR ALL REPAIRS REIMBURSED BY SUBARU THAT REQUIRE A MAJOR REPAIR OR REPLACEMENT, EXCEPT IN THE CASE OF A NEW AND IN-STOCK VEHICLE.
06-52-15
THIS BULLETIN PROVIDES AN INSPECTION AND ADJUSTMENT PROCEDURE TO ADDRESS A DTC C0075 WHICH MAY BE STORED IN THE VEHICLE DYNAMICS CONTROL AND HYDRAULIC CONTROL UNIT (VDCCM&HCU). THE DTC RELATES TO INCORRECT INPUTS TO WHEEL CYLINDER PRESSURE SENSORS DUE TO AIR IN THE HYDRAULIC BRAKE LINES. IN ADDITION, ON IMPREZA AND XV CROSSTREK, AN IMPROPERLY ADJUSTED BRAKE LIGHT SWITCH (BLS) MAY ALSO CAUSE THE DTC.
12-189-15
THIS BULLETIN PROVIDES INFORMATION ABOUT CHANGES MADE TO THE REAR SHELF TRIM TO ADDRESS CUSTOMER CONCERNS OF A RATTLING SOUND HEARD WHILE DRIVING OVER BUMPY / ROUGH ROADS. THE SOURCES OF THE RATTLE HAVE BEEN IDENTIFIED AS THE MOUNTING FOR THE CENTER STOP LAMP IN THE PACKAGE SHELF AND / OR THE SHELF ITSELF RATTLING AGAINST THE INSIDE OF THE REAR GLASS.
02-162-15R
THIS SERVICE INFORMATION BULLETIN ANNOUNCES A DESIGN CHANGE TO THE OIL PRESSURE SWITCH ASSEMBLY. NICKEL PLATING HAS BEEN APPLIED TO THE INTERNAL SWITCH CONTACTS TO ENHANCE THEIR DURABILITY AND REDUCE THE POSSIBILITY OF POOR CONTACT WHICH COULD AFFECT OPERATION OR CAUSE IMPROPER ILLUMINATION OF THE OIL PRESSURE WARNING LAMP. A SMALL PILOT PORTION WAS ADDED TO THE THREADED AREA ON P.N. 25240KA051 AS SHOWN IN THE ILLUSTRATION BELOW. REVISED PRODUCTION CHANGE INFORMATION.
02-162-15
THIS SERVICE INFORMATION BULLETIN ANNOUNCES A DESIGN CHANGE TO THE OIL PRESSURE SWITCH ASSEMBLY. NICKEL PLATING HAS BEEN APPLIED TO THE INTERNAL SWITCH CONTACTS TO ENHANCE THEIR DURABILITY AND REDUCE THE POSSIBILITY OF POOR CONTACT WHICH COULD AFFECT OPERATION OR CAUSE IMPROPER ILLUMINATION OF THE OIL PRESSURE WARNING LAMP. A SMALL PILOT PORTION WAS ADDED TO THE THREADED AREA ON P.N. 25240KA051 AS SHOWN IN THE ILLUSTRATION BELOW.
15-185-15R
THIS SERVICE INFORMATION BULLETIN IS INTENDED TO PROVIDE HELPFUL INSIGHT TO USE WHEN RESPONDING TO CUSTOMER INQUIRIES INVOLVING THE PAIRING AND USE OF CELLULAR PHONES WITH CLARION AUDIO UNITS. THIS INCLUDES CUSTOMER CONCERNS WHERE THE PHONE WILL NOT AUTOMATICALLY PAIR ITSELF BUT INSTEAD REQUIRES MANUAL PHONE SELECTION ON THE AUDIO UNIT TO ALLOW PAIRING TO PROCEED.
15-185-15
THIS SERVICE INFORMATION BULLETIN IS INTENDED TO PROVIDE HELPFUL INSIGHT TO USE WHEN RESPONDING TO CUSTOMER INQUIRIES INVOLVING THE PAIRING AND USE OF CELLULAR PHONES WITH CLARION AUDIO UNITS. THIS INCLUDES CUSTOMER CONCERNS WHERE THE PHONE WILL NOT AUTOMATICALLY PAIR ITSELF BUT INSTEAD REQUIRES MANUAL PHONE SELECTION ON THE AUDIO UNIT TO ALLOW PAIRING TO PROCEED.
06-50-15
THIS BULLETIN INFORMS OF A PARTS CHANGE TO THE BRAKE SYSTEM MASTER CYLINDER AND VACUUM BOOSTER. WHENEVER REPLACEMENT OF EITHER OF THESE COMPONENTS IS REQUIRED, THE IDENTIFICATION PROCEDURE PROVIDED BELOW MUST BE FOLLOWED TO INSURE THE PROPER PARTS ARE ORDERED AND INSTALLED AS A SET.
SB-06-50-15
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
18-181-15
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes. We advise you to always refer to the STIS web site when looking for the latest Service information. Printed pages will not be made available to update printed Service Manuals.
18-181-15 (2)
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes. We advise you to always refer to the STIS web site when looking for the latest Service information. Printed pages will not be made available to update printed Service Manuals.
11-157-15
THIS BULLETIN ANNOUNCES AVAILABILITY OF REPROGRAMMING FILES TO ADDRESS CUSTOMER CONCERNS OF AN EXTENDED CRANKING TIME BEFORE THE ENGINE STARTS.
06-48-15
THIS BULLETIN ANNOUNCES A DESIGN CHANGE TO THE STOP LIGHT SWITCH TO REDUCE THE POSSIBILITY OF IMPROPER ILLUMINATION OF THE ABS AND/OR VDC WARNING LAMP WITH RESULTING DTCS C1531 AND/OR C0054. DETAILS OF THE SWITCH CHANGES ARE SHOWN IN THE ILLUSTRATION BELOW.
SB-06-48-15
SUBARU: ON SOME VEHICLES, TO REDUCE POSSIBILITY OF IMPROPER ILLUMINATION, A CHANGE IN DESIGN FOR STOP LIGHT SWITCH FOR ABS AND/OR VDC WARNING LAMP. MODELS 2012-14 IMPREZA, XV CROSSTREK (EXCEPT HYBRID), 2008-14 WRX, STI, 2014 FORESTER. *PE
SB-04-13-14R
SUBARU: AN ISSUE OF INCREASE STEERING EFFORT, ELECTRIC POWER STEERING (EPS) WARNING LIGHT COMES ON WITH DIAGNOSTIC TROUBLE CODE (DTC) C2532 AND TO ADDRESS CODE A NEW EPS CONTROL UNIT THAT IS AVAILABLE. MODEL 2014 FORESTER, 2012-14 IMPREZA, XV CROSSTREK (INCLUDING HYBRID). *PE
02-160-15
This Service Information bulletin provides revised procedures for inspection and measurement of the cylinder block assembly to determine whether or not replacement is necessary. Read through and understand this information completely before proceeding with any repairs to the cylinder block. All Models with FA and FB Engines, 2011MY and Later.
11-149-14R
This bulletin announces the availability of reprogramming files and a revised oil level switch to optimize the ECM logic for engine oil level detection in the event of false or premature low engine oil level warning lamp illumination. Revised to add models.
12-182-15
THIS BULLETIN ANNOUNCES AVAILABILITY OF A REVISED FRONT DOOR CHECKER MECHANISM DESIGNED TO HOLD THE FRONT DOORS MORE SECURELY WHEN THEY ARE IN PARTIALLY OPEN POSITIONS. AN ADDITIONAL DETENT POSITION HAS ALSO BEEN ADDED.
SMG-SS
THIS ANNOUCMENT IS TO ANOUCE THE STOP THE SALES OF THE (2012 TO 2015) IMPREZA AND (2013 TO 2015) XV CROSSTREK SPORT MESH GRILLES.
18-177-15
THE PURPOSE OF THIS BULLETIN IS TO PROVIDE A DESCRIPTION OF CURRENT CHANGES TO SERVICE MANUALS AVAILABLE VIA THE SUBARU TECHNICAL INFORMATION SYSTEM (STIS) WEB SITE.
15-179-15R
THIS SERVICE INFORMATION BULLETIN CONTAINS A SERIES OF SCREEN SHOTS WITH INSTRUCTIONS WHICH PROVIDE A PROCEDURE FOR PAIRING ANDROID SMARTPHONES TO BLUETOOTH-EQUIPPED CLARION AUDIO UNITS. THE PROCEDURE INVOLVES CHANGING THE AUDIO UNITS DEFAULT PASSKEY WHICH MUST BE ENTERED INTO THE SMARTPHONE DURING THE PAIRING PROCESS. ONCE THE PASSKEY IS CHANGED FROM 1234 TO 0000, TESTING RESULTS HAVE SHOWN THE REMAINDER OF THE PAIRING PROCESS COMPLETES NORMALLY.
NAVI- SYSTEM-1
GEN I SD CARD NAVIGATION SYSTEM TROUBLE SHOOTING GUIDE
05-59-15
THIS SERVICE INFORMATION BULLETIN ANNOUNCES A CHANGE TO THE FLANGED MOUNTING NUTS SECURING THE FRONT STRUT ASSEMBLIES TO THE VEHICLE BODY. THE CHANGE WAS MADE TO ENHANCE ASSEMBLY LINE EFFICIENCY.
1114514R-3
Reprogramming File Availability for Oil Level Detection
1114914R-1
Reprogramming File Availability for Oil Level Detection
1114914R
Reprogramming File Availability for Oil Level Detection
18-175-14
SERVICE MANUAL CORRECTIONS - THE PURPOSE OF THIS BULLETIN IS TO PROVIDE A DESCRIPTION OF CURRENT CHANGES TO SERVICE MANUALS AVAILABLE VIA THE SUBARU TECHNICAL INFORMATION SYSTEM (STIS) WEB SITE.
1817514
Service Manual Corrections
11-149-14
REPROGRAMMING FILE AVAILABILITY FOR OIL LEVEL DETECTION
1114914
Reprogramming File Availability for Oil Level Detection
0215514R
Intercooler/Intake Air Duct
SB-02-155-14-R
SUBARU: INFORMATION REGARDING REPLACEMENT REVISION OF AIR INTAKE DUCT FOR TURBOCHARGER WHERE INSULATOR PORTION OF DUCT SEPARATES FROM DUCT AND LEAKS BOOST PRESSURE, LOSS OF POWER AND INCREASED SOUND LEVELS OCCURS. MODEL 2005-12 LEGACY, OUTBACK TURBO, 2009-13 FORESTER TURBO, 2008-14 IMPREZA WRX. *PE
DigitalDealer
The 17th Digital Dealer Conference & Exposition
TechTIPS
Subaru Service and Technical Support Line Newsletter
0116809R
Replacement Key and Immobilizer Info
142014R
Subaru Leak Detection System
02-132-12R
DIAGNOSIS AND REPAIR FOR AVCS-RELATED DTCS P000A, P000B, P000C, P000D, P0011, P0014, P0021 AND P0024
0213212R
Diagnosis and Repair for AVCS-Related DTCs
Article
Drive Magazine article titled ?Engine Oil, Maintenance and Warnings?
1516813R
Exchange Component Identification and procedures
07-85-14
MEASUREMENT OF DARK CURRENT (PARASITIC BATTERY DRAW)
171713R
Event Data Recorder (EDR) Function of Airbag Module
TechTIPS1
Subaru Service and Technical Support Line Newsletter
0215214
Revised Valve Train Parts to Reduce a Warm Engine Tapping Sound from the Left Cylinder Head
06-46-14
REVISED BRAKE LIGHT SWITCH ADJUSTMENT PROCEDURE FOR DTCS C1531 AND C0054
064614
This bulletin provides a revised adjustment procedure to be used when diagnosing Brake Light Switch (BLS) -related DTCs C1531 and/or C0054. If the BLS is out of adjustment, the ABS and/or VDC warning lamp may illuminate.
0215514
Intercooler/Intake Air Duct
07-83-14
DIAGNOSTICS FOR DTC B1500 AND U1500
078314
Diagnostics for DTC B1500 and U1500
03-72-14
HILL START ASSIST (HSA) WARNING LIGHT, DTC C0076 - THIS BULLETIN PROVIDES INFORMATION TO ADDRESS A CUSTOMER CONCERN OF INTERMITTENT OPERATION OF THE HILL START ASSIST WARNING LAMP.
05-57-14
FRONT CROSS MEMBER MOUNTING BOLT CHANGE - THIS BULLETIN DESCRIBES A DESIGN CHANGE MADE TO THE MOUNTING BOLTS USED FOR SECURING THE FRONT CROSS MEMBER TO THE VEHICLE BODY.
055714
Front Cross Member Mounting Bolt Change
TSB-05-57-14
SUBARU: A CHANGE HAS BEEN MADE TO THE MOUNTING BOLTS USED FOR SECURING THE FRONT CROSS MEMBER TO THE VEHICLE BODY. THE THICKNESS OF THE FLANGE AT THE BASE OF THE BOLT'S HEX HAS INCREASED TO 5MM. ALSO INCLUDED SUBARU STI/BRZ MODEL YEAR 2014. *JS
TSB-2-20-14
SUBARU: THE CUSTIOMER MAY COMPLAIN OF THE INTERMITTENT OPERATION OF THE HILL START ASSIST WARNING LAMP. STORED DTC C0076 WITH DETAIL CODES 2610H AND/OR 2620H. *JS
04-13-14
NEW ELECTRIC POWER STEERING (EPS) CONTROL UNIT FOR DTC C2532
041314
New Electric Power Steering (EPS) Control Unit for DTC C2532
03-70-12R
REPAIR PROCEDURE FOR HIGH-PITCHED SOUND FROM EXTENSION HOUSING AREA USING LATEST GENERATION PRODUCTION PARTS - THIS BULLETIN PROVIDES PRODUCTION CHANGE, REPAIR PROCEDURE AND PARTS INFORMATION TO ADDRESS A CUSTOMER CONCERN OF A HIGH-PITCHED SOUND COMING FROM THE TRANSMISSION EXTENSION HOUSING AREA.
037012R-1
Repair Procedure for High-Pitched Sound from Extension Housing Area Using Latest Generation Production Parts
12-161-14
LOOSE OR MISSING FOG LAMP COVERS - THIS BULLETIN PROVIDES A SERVICE PROCEDURE FOR IMPROVING THE RETENTION OF THE FOG LAMP COVERS INTO THE FRONT BUMPER COVER.
1216114
Loose or Missing Fog Lamp Covers
09-56-13
A COUNTERMEASURE THERMOSTAT HAS BEEN RELEASED TO ADDRESS A RARE CONDITION WHICH MAY OCCUR DURING ENGINE SOAK IN COLD AMBIENT TEMPERATURES. IN THESE RARE CASES, AFTER AN EXTENDED COLD SOAK, COOLANT MAY ENTER THE THERMOSTATS INTERNAL PISTON. IF THIS OCCURS, THE THERMOSTAT MAY OPEN AT A TEMPERATURE WHICH IS LOWER THAN SPECIFIED AND CAUSE DTC P0128 TO BE STORED IN THE ECM MEMORY.
WQH-44M
WE HAVE RECEIVED SEVERAL CALLS FROM DEALERS WHO HAVE CUSTOMERS ELIGIBLE FOR THE WQH44 SUBARU CARPETED FLOOR MAT RECALL BUT DO NOT HAVE THE ORIGINAL MATS THAT WERE IN THE VEHICLE AT THE TIME OF SALE. IN MOST CASES, THE CUSTOMERS HAVE STATED THAT THEY HAVE DISCARDED OR DESTROYED THE MATS. IN OTHER INSTANCES, THE CUSTOMERS INDICATED THAT THEIR VEHICLE DID NOT HAVE THE MATS WHEN THEY PURCHASED THE VEHICLE. IF, OR WHEN, THIS SITUATION ARISES, PLEASE FILL OUT THE ATTACHED FORM AND HAVE THE CUSTOMER SIGN IT AND RETAIN THE SIGNED FORM WITH THE REPAIR ORDER. IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT THE CLAIMS HELPLINE AT 866-782-2782.
18-173-13
THE PURPOSE OF THIS BULLETIN IS TO PROVIDE A DESCRIPTION OF CURRENT CHANGES TO SERVICE MANUALS AVAILABLE VIA THE SUBARU TECHNICAL INFORMATION SYSTEM (STIS) WEB SITE. THE TABLES CONTAINED WITHIN THIS BULLETIN ARE TO BE USED AS GUIDES FOR BECOMING AWARE OF THE LATEST CHANGES. WE ADVISE YOU TO ALWAYS REFER TO THE STIS WEB SITE WHEN LOOKING FOR THE LATEST SERVICE INFORMATION. PRINTED PAGES WILL NOT BE MADE AVAILABLE TO UPDATE PRINTED SERVICE MANUALS.
15-168-13
THIS BULLETIN CONTAINS ILLUSTRATIONS OF EXCHANGE COMPONENTS AND THEIR MANUFACTURER AS WELL AS A DESCRIPTION OF THE PROPER EXCHANGE PROCEDURE. THE EXCHANGE PROGRAM POLICY CAN ALSO BE FOUND IN SECTIONS 8.4.9 AND 11.2.10 OF YOUR SERVICE POLICIES AND PROCEDURES MANUAL FOUND IN SUBARUNET.
1516813
Exchange Component Identification and prcedures
13-96-13R
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
139613R
Paint Coding Information
1817213
Service Manual Corrections
037012R
This Bulletin provides production change, repair procedure and parts information to address a customer concern of a high-pitched sound coming from the transmission extension housing area.
TSG-1
Tech Support SD Card for Navi Complete
13-96-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
139613
Paint Coding Information
86271FJ600
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
0214013
Oil Filler Cap Gasket Coming Unseated
171713
Event Data Recorder (EDR) Function of Airbag Module
SOA321099
Special Service Tools
SST
THE FOLLOWING ARE THE SPECIAL TOOLS THAT ARE REQUIRED FOR THE 2014 MY. THESE TOOLS WILL BE SHIPPED DIRECTLY TO ALL DEALERS DURING MARCH. THE CHART DESCRIBES EACH OF THE TOOLS IN THE SHIPMENT.
WQE41-1
Puddle Light Recall
0117113
Additional PDI Procedure for Installation of Tie-Down Hole Plugs
037012
Repair Procedure for High-Pitched Sound from Extension Housing Area Using Latest Generation Production Parts
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.