Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
15-308-23R
This Service Information Bulletin outlines a systematic procedure for diagnosing parasitic draw (dark/standby current) in vehicles experiencing battery drain when the ignition is off, leading to no-start conditions or frequent jump-starts.This is an revised version of the original bulletin.
15-304-22R
This Bulletin has been developed to outline the steps for gathering basic but essential information during diagnosis of Infotainment concerns. (This is an revised version of the original bulletin.)
Article Locator
Techtips newsletter locator index.
15-333-25R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. This is an revised version of the original bulletin
02-193-24R
This bulletin provides updated parts information and a service procedure to follow for removing accumulated carbon deposits from fuel injectors and internal engine components (e.g. intake valves and / or manifold, and combustion chambers). (This is an revised version of the original bulletin.)
09-74-21R
This bulletin provides updated parts information and a service procedure to follow for removing accumulated carbon deposits from fuel injectors and internal engine components (e.g. intake valves and / or manifold, and combustion chambers). (This is an revised version of the original bulletin.)
SubaruNet Annoucement (E
This announcement is requesting retailer staff to retain the EyeSight protective hood covers from Generation 4 EyeSight cameras.
01-167-08R
This bulletin contains additional information for recommended materials listed in the Service Manuals for individual models.
SubaruNet Announcement (R
This announcement provides information on the remanufactured CVT transmission program.
07-240-26R
This Service Information Bulletin was developed to provide interim guidance for vehicles exhibiting DTC B2A20.
03-97-26
This bulletin announces the service manual correction regarding clutch master cylinder reservoir service procedures.
05-97-26
This Bulletin provides the diagnostic procedures to be followed when addressing customer concerns of steering wheel/vehicle body vibration when driving at highway speeds when tire/wheel balance is suspected.
10-105-25R
This bulletin announces the new procedure and Warranty Fail Code for FirstTime air conditioning (A/C) performance concerns possibly resulting from an undetected A/C refrigerant leak.
15-219-18R
This bulletin contains information to help when attempting to complete the STARLINK Telematics subscription process, an Error Code 202 and / or 204 may occur preventing the process from completing successfully
SubaruNet Announcement (A
This announcement provides information on the use of aftermarket services or tools for programming immobilizer keys/fobs.
Subaru Tech Tips Special
This Subaru service and technical support line newsletter provides information on the next phase of TechShare.
15-300-22R
This Bulletin provides the diagnostic procedure for the STARLINK® Remote Engine Start (RES).
Subarunet Announcement (E
This announcement has been created to address difficulties with software updates on Subaru Select Monitors with DST-010 interface firmware has been updated.
05-84-21R
This bulletin announces availability of new front wheel hub assemblies incorporating bearing surfaces having increased resistance to imperfections resulting from shock loads.
18-226-25R
This Service Information Bulletin provides the Service Manual Correction to the diagnostic procedure for DTC B2A16 (Immobilizer Key Collation Diagnosis).
18-228-25R
This bulletin announces the diagnostic procedures to be used when DTCs P2096 (POST CATALYST FUEL TRIM SYSTEM TOO LEAN BANK 1) and P2097 (POST CATALYST FUEL TRIM SYSTEM TOO RICH BANK 1) are detected by the Engine Control Module (ECM).
15-333-25
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
18-228-25
This bulletin announces the diagnostic procedures to be used when DTCs P2096 (POST CATALYST FUEL TRIM SYSTEM TOO LEAN BANK 1) and P2097 (POST CATALYST FUEL TRIM SYSTEM TOO RICH BANK 1) are detected by the Engine Control Module (ECM).
Subaru Tech Tips (Article
Subaru service article locator.
15-130-08R
This bulletin provides information on the load carrying capacity reduced label when a port-installed or retailer-installed accessory exeeds 1.5 percent of the GVWR or 100 pounds, which ever is lower.
07-233-25R
This Bulletin provides details on a new formal testing, charging, and tracking procedure for all 12-volt batteries in new vehicle inventory.
07-236-25
This Bulletin outlines a comprehensive update to the dark current/parasitic draw diagnosis & testing procedures.
07-233-25
This Bulletin provides details on a new formal testing, charging, and tracking procedure for all 12-volt batteries in new vehicle inventory wjhich must be tested and reported every 30 days.
15-266-20R
This Bulletin provides helpful procedures and best practices to utilize when customers present with concerns relating to the operation of their Gen 2/Gen 3 Telematics system equipped Subaru.
15-320-24R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
SubaruNet Announcement
Subaru of America, Inc. will release an OTA to perform a software update to the DCM. This is a preventive OTA.
09-131-25R
This bulletin announces the diagnostic procedures and availability of reprograming files to rectify the following Diagnostic Trouble Codes (DTCs). • P2404: EVAP System Leak Detection Pump Sense Circuit Range/Performance. • P0420: Catalyst System Efficiency Below Threshold Bank 1. (not applicable for 15-18 models)
13-108-25
This bulletin provides information on paint codes for vehicles in the 2026 line up.
Subaru Service Technical
Subaru Service Technical Support Newsletter special edition.
SubaruNet Annoucement
This announcment provides information on the release of the latest software updates to the Subaru Midtronics DSS-5000 Battery Diagnostic tool.
15-251-19R
This Bulletin provides additional diagnostics to follow when addressing a Telematics-related DTC B2A16.
SubaruNet Announcement (S
This announcement is to bring attention to the OTA for In-vehicle service appointment scheduler and In-vehicle message center.
01-168-09R
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site.
02-192-24R
This Bulletin announces the diagnostic procedures to be followed when diagnosing engine oil leakage on FA and FB type engines.
03-96-25
This bulletin announces design changes made to the rear axle hubs. These changes have been implemented to reduce cases water intrusion further leading to harmonic, humming, and grinding type sounds heard from the axle hub while driving.
14-31-25
This Bulletin announces availability of a User Guide and an informative video to supplement the recent releases to retailers of the SOA321152 and SOA321153 Terminal Test Kits.
09-51-08R
The purpose of this bulletin is to advise of SOA’s revised Catalytic Converter Recycling Program shipping procedure.
16-103-16R
This bulletin has been developed in response to a small number of customer concerns regarding fluid seepage found coming from the CVT assembly.
Subarunet Announcement
This announcement is in regard to special service tool shipment will be shipped directly to the Subar retailers during February.
RC5 Head Unit OTA
A head unit OTA will be available via cellular network for Mid and High Grade CP1.5 head units.
02-193-24
This bulletin provides updated parts information and a service procedure to follow for removing accumulated carbon deposits from fuel injectors and internal engine components (e.g. intake valves and / or manifold, and combustion chambers).
07-59-07R
This bulletin is for information purposes only.The bulletin adresses design changes of the headlamps and rear combination lamps, where moisture and or condensation may develop on the inside of the lamp lenses.
15-298-22R
This Service Information Bulletin announces the preferred practices to be used when handling vehicles equipped with Gen2 Telematics which are enrolled in the Subaru STARLINK® Security Plus Service featuring Stolen Vehicle Recovery Plus with Immobilizer.
02-192-24
This Service Information Bulletin announces the diagnostic procedures to be followed when diagnosing engine oil leakage on FA and FB type engines.
07-178-21R
This Service Information bulletin is being released as guidance for proper testing and charging of vehicle batteries.
15-320-24
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
02-191-22R
This bulletin announces availability of the NEW genuine Subaru engine oil filter.
03-94-24
This bulletin outlines the judgment criteria to be used when inspecting front transverse link bushings to reduce unnecessary bushing replacement.
Thermo Control Valve Vide
This thermo control valve video contains information on the replacement of thermo control valve.
13-107-24
This Bulletin provides SOA paint codes to help eliminate possible confusion for 2025 MY vehicles.
05-91-24
This Bulletin provides guidance for diagnosing a leaking front or rear suspension strut.
06-90-24
This bulletin provides diagnosis and procedure information to be applied when diagnosing potential fluid leaks on front and rear brake calipers. This information has been developed to reduce unnecessary brake caliper replacement.
16-112-18R
This bulletin announces a design change to the CVT select lever (shifter) mechanism in response to isolated customer concerns of not being able to remove the key from the ignition switch when the vehicle is in Park.
07-207-22R
In the interest of customer satisfaction, Subaru of America, Inc. is extending the New Car Basic Warranty coverage for the 12 Volt batteries used in the above listed models and model years beyond the original three (3) years or thirty six thousand miles (36,000), whichever comes first.
18-231-23
This Bulletin announces additional information regarding error codes 1403- 1407 encountered when attempting an adjustment/calibration of the EyeSight® system after body repair procedures have been performed.
15-285-21R
This Bulletin provides reference tables and photos to use for determining the infotainment head unit supplier and generation.
12-249-23R
This bulletin announces the recommended cleaning procedures to followed when encountering vehicles with long time exposure to pollen on painted surfaces on vehicles imported from Japan. This bulletin does not apply to SIA built vehicles.
02-131-12R
The purpose of this Bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the timing chain cover, front camshaft cap, camshaft carrier and / or upper oil pan.
06-87-22R
In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Warranty coverage for the electronic connector lock tab for the Electric Parking Brake (EPB) assembly used in the listed models.
03-78-17
This bulletin announces a design change to the clutch release bearing.
16-131-20R
This Service Information Bulletin provides an updated diagnostic flow along with an IMPORTANT caution to follow for certain CVT solenoid related DTCs as listed.
Subarunet Announ
In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is announcing an extension to the Basic New Car Limited Warranty for the Electronic Parking Brake (EPB) connector lock tab for certain 2015-2018MY Legacy, Outback & WRX models equipped with automatic transmissions.
5-88-21R
This bulletin announces a design change made to the front stabilizer bushings.
SubaruNet Announ
Battery Class Action Settlement Updates.
15-302-22
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
18-207-22
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
Subaru Tech Tips
Special Edition, 2012 current model subaru evaporative diagnostics and smoke testing.
15-298-22
This Bulletin announces the preferred practices to be used when handling vehicles equipped with Gen2 Telematics which are enrolled in the Subaru STARLINK® Security Plus Service featuring Stolen Vehicle Recovery Plus with Immobilizer.
05-88-21
This bulletin announces a design change made to the front stabilizer bushings.
12-288-20R
This bulletin announces a design change made to the Slide Rail components of the left and right front power seat frame / track assembliesd.
12-203-16R
This bulletin provides a procedure to address customer concerns of a squeaking sound originating from where the front seat belt buckle assembly attaches to the seat frame.
18-220-22
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
15-192-22R
This bulletin has been developed to outline the steps for gathering basic essential information during diagnosis and repair of the Infotainment concerns. (Applicable to all models with Harman or Denso CP1 Infotainment).
02-189-22
This Bulletin announces design changes to the engine oil and CVT fluid drain plugs.
16-102-16R
This bulletin provides a new flow chart and additional diagnostic tools to assist technicians with troubleshooting DTC P0841- SECONDARY OIL PRESSURE SENSOR PERFORMANCE.
05-79-20R
This bulletin announces a change made to the wheel lug nuts.
09-78-21
This bulletin announces the availability of Engine Control Module (ECM) reprograming files to correct DTC P015A and/or P015B.
15-208-17R
This bulletin announces availability of an enhancement to the Gracenote database included in the vehicles listed equipped with F10 7â Navigation and 7â Display Audio head units.
18-212-21
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
15-177-14R
This bulletin provides information to help diagnose and address different conditions relating to customer concerns which may arise when operating the new-generation âGen 2â and âGen 2.1â F10 Navigation and Display Audio systems.
02-187-21
This bulletin outlines changes in the service procedure for engine oil pressure inspection.
18-210-21
Description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
05-84-21
This bulletin announces availability of new front wheel hub assemblies incorporating bearing surfaces having increased resistance to imperfections resulting from shock loads.
11-199-20R
This bulletin announces availability of reprogramming files to optimize the Engine Control Module (ECM).
06-59-17R
This Service Information bulletin announces availability of a new front brake pad shim kit to specifically address customer concerns of a squeaking or squealing sound on the models listed above.
14-22-16R
To help reduce confusion and increase technician efficiency, Subaru of America, Inc. (SOA) has developed the following cross reference list to help locate the appropriate Special Service Tool.
12-308-21
This bulletin announces a design change made to the front seat hinge bolts.
03-78-17R
This bulletin announces a design change to the clutch release bearing.
15-205-16R
This bulletin announces new reprogramming file availability and the software installation procedure to address additional operational concerns received from the field and listed involving âGen 2â F10 Navigation and Display Audio units with 7â display.
05-79-20
This Service Information Bulletin announces a change made to the wheel lug nuts.
12-305-20
This bulletin announces a design change made to the front hood air intake duct.
12-306-20R
This bulletin provides a repair procedure to address a squeaking sound coming from the backrest hinge area of the front seats. The procedure applies to both manually and power operated seat assemblies.
16-131-20
This Service Information Bulletin provides corrected diagnostics containing a revised flow for certain CVT solenoid related DTCs.
03-86-20
This bulletin provides additional repair procedures to follow when replacing a leaking clutch master cylinder on certain vehicles.
10-19-20
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
12-301-20
This bulletin outlines changes made to the rear shelf trim to address customer concerns of a rattling sound heard while driving over bumpy / rough roads.
06-77-20R
This bulletin announces the availability of reprogramming files to optimize the control module for the Vehicle Dynamics Control system (VDCCM). DTCs C1531 and/or C1741 may set, the Hill Holder warning lamp and cancellation alarm may activate and/or the VDC warning lamp can illuminate.
18-201-20
The purpose of this bulletin is to provide a desription of current changes to service manuals available via the Subaru Technical Information System (STIS) web site.
18-200-20
This bulletin provides a description of current changes to Service Manuals.
06-79-20
This bulletin announces availability of new master cylinder application shaft seals.
03-82-18R
This service information bulletin announces a design change to the clutch release bearing used on the models listed.
15-266-20
This Service Information Bulletin provides helpful procedures and best practices to utilize when customers present with concerns relating to the operation of their Gen 2 Telematics system equipped Subaru.
15-267-20
This document discusses some of the conditions that may trigger an Automatic Collision Notification (CAN) (Gen1) or Advanced Automatic Collision Notification (AACN) (Gen2), without a collision, airbag deployment, or accident taking place.
06-76-20
This service Information bulletin provides precautions to follow when servicing the Brembo brake calipers utilized on the models listed. Because of their aluminum construction, it is critcal to take extra care when servicing.
12-290-20
This Bulletin announces a design change made to the front seat backrest cover trim material on the models listed. The new material has enhanced wear resistance, especially in the side bolster area which may show wear over time from getting in and out of the seat.
12-288-20
This bulletin announces a design change made to the Slide Rail components of the left and right front power seat frame / track assemblies used on the models listed.
01-181-20
All Models (Vehicle Cleaning- COVID-19Best Practices)
07-174-20
This service bulletin provides details of a correction to the diagnostic procedure for DTC B2350- REAR RADAR COMMUNICATION ERROR on the models listed.
WUK-96R
Subaru of America, Inc. (Subaru) is initiating a service campaign for certain 2015-2018 Forester 2.0L Turbo and 2016-2018 WRX models which may experience a loosening of the front exhaust pipe nuts.
12-284-20
This bulletin announces availability of new interior door handles which will address isolated concerns of the chrome finish peeling.
17-17-13R
This bulletin provides information regarding Event Data Recorder (EDR) functionality which has been incorporated into the airbag system.
07-75-13R
This Bulletin provides information regarding DTC P0606 related specifically to the determination of this code on Forester Turbo and applicable WRX models.
03-83-20R
This bulletin announces availability of new shift forks and the corresponding sleeve and hub assembly to address isolated customer concerns of a rattling / vibration -type sound from the shift knob. The sound is primarily reported while driving in 4th gear between 1900 and 2500 rpm.
07-169-20
This Service Information bulletin describes a change made to the labels applied to the push to start switches used on the models listed.
15-199-16R
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field and listed below involving the Clarion Display Audio unit with 6.2" display.
11-199-20
This bulletin announces availability of reprogramming files to optimize the Engine Control Module (ECM). The new logic will address isolated concerns of a hard start condition occurring in cold weather (+10 degrees Fahrenheit or lower) and / or high-altitude areas. When this scenario occurs, the A/F learning control values move toward lean.
Subarunet Annou
Owner notification WUK-96 DIT exhaust pipe front (EPF) nut torque service campaign/voluntary emission recall.
07-152-19R
This bulletin announces availability of new power window switch assemblies.
07-167-20
This bulletin announces availability of a new stop lamp switch for the models listed above equipped with LED - type rear combination lamps.
15-190-15R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. The exchange program policy can also be found in Sections 8.4.9 and 11.2.10 of your Claims Policies and Procedures Manual found in subarunet.
10-96-19
This bulletin announces availability of a new HVAC blower motor unit assemblies developed to address isolated concerns of the blower motor becoming inoperative. If this issues occurs on models with Auto A/C, the blower fan may become totally inoperative. If this issue occurs on models with Manual A/C, the blower fan may operate on high speed only. The root cause of these conditions is water intrusion into the blower motor causing rust and corrosion to develop. Over time, the blower motor may begin to draw more electrical current to operate. if that occurs, the additional draw can cause the related fuse and/ or blower resistor to fail. To address this condition, additional packing has been added to improve sealing of the blower unit case along with development of a new style cabin air filter which also in corporates improved sealing.
12/275/19
This bulletin announces a change made to the leather front seat cushion covers to address isolated concerns of a sagging/loose fitting condition after an occupant leaves the seat as shown in the example photos below. A pattern revision was made to increase tension of the cover material and decrease the time it takes for the condition to disappear after an occupant leaves the seat.
Subaru Announ
Subaru of America, Inc. (Subaru) is initiating a service campaign/ voluntary emissions recall for certain 2015-2018 Forester 2.0L Turbo and 2016-2018 WRX models which may experience a loosening of the fornt exhaust pip nuts.
WUK-96
Subaru of America, Inc. (Subaru) is initiating a service campaign for certain 2015-2018 Forester 2.0L Turbo and 2016-2018 WRX models which may experience a loosening of the front exhaust pipe nuts. On certain affected vehicles, the six (6) front exhaust pipe (EPF) nuts at the cylinder heads may not have been tightened sufficiently due to variations in production. As a result, these nuts may become loose during use and cause exhaust leakage. A leak occurring at the front exhaust pipe may result in deterioration of emission performance. As a result, affected vehicle may fail to meet emission levels certified by the EPA and/or California ARB.
07-146-19R
This bulletin announces a design change made to the engine wiring harness to improve resistance to moisture. A detailed illustration describing the change is supplied below.
12-271-19
This Service Information Bulletin announces a design change made to the rear bumper cover side mounting brackets. These new brackets provide increased clearance between the edges of the bumper cover and the corresponding quarter panels. This change will prevent them from contacting each other and possibly damaging their painted surfaces.
11-191-19R
This bulletin announces availability of a new Engine Control Module (ECM) for the models listed above designed to address DTC P2610: âECM/PCM ENGINE OFF TIMER PERFORMANCEâ. Under certain RARE conditions, an electrostatic surge may influence the ECMâs internal timer used after the engine is turned off and store a DTC P2610 in memory. Hardware in the ECM has been changed to eliminate any impact from electrostatic surges.
11-191-19
This bulletin announces availability of a new Engine Control Module (ECM) for the models listed above designed to address DTC P2610: âECM/PCM ENGINE OFF TIMER PERFORMANCEâ. Under certain RARE conditions, an electrostatic surge may influence the ECMâs internal timer used after the engine is turned off and store a DTC P2610 in memory. Hardware in the ECM has been changed to eliminate any impact from electrostatic surges.
06-65-18R
This bulletin announces a new Vehicle Dynamics Control (VDC) Module and Hydraulic Control Unit (VDCCM&HCU). The new part was designed to address a small number of customer concerns regarding a clicking or ticking-type sound heard coming from the driverâs side footrest area. The new modules incorporate logic with enhanced internal solenoid and motor control characteristics.
06-68-19R
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. This will prevent the pad from dragging due to corrosion buildup which may result in uneven or premature wear of the replacement brake pads. This additional instruction applies to all models with brake pads using the upper and lower pad clips and has been added to the brake pad installation procedures found in the related Service Manuals.
WUE-90 tool
SOA has received multiple requests for additional 83399Fj000rt BRAKE LIGHT SWITCH tools and now has sufficient stock to allow retailers to place orders for single tools.
02-163-16R
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. The applicable Service Manuals will be revised with this new information in the near future.
02-182-19
This Service Information bulletin announces a design change made to the TGV assemblies used on the Forester Turbo models and WRXs listed above. Condensation resulting from EGR system operation may enter the area between the TGV shaft and bearing. Over time, corrosion can develop and impede movement of the TGV shaft and cause any of the DTCs P2004, 2005, 2006 and /or P2007 to set. The material of the TGV shaft has been changed to stainless steel to optimize corrosion resistance.
12-264-19
This Service Information bulletin announces a design change made to the retaining bolt used to secure the child anchors to the rear shelf plates on the models listed above. This change was made in support of parts communization with other similar mounting bolts. There is no change between the old and new bolt in terms of function or durability.
04-17-17-R
This bulletin provides a service procedure to address isolated customer concerns of a rattling sound identified as coming from the Electronic Power Steering (EPS) gear box (steering rack) assembly. The repair (when applicable) involves installation of a new tension spring for the worm gear to reduce / eliminate the condition.
07-152-19
This bulletin announces availability of new power window switch assemblies developed to address the following customer concerns: ? Power windows inoperative from the driver?s door master and / or passenger front door switch ? Unable to remotely operate other door windows from the driver?s door master switch ? One-Touch Auto Up / Down features inoperative from either / both front door switches
02-170-17R
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. The new seal will eliminate potential oil seepage into the wire harness connector portion of the valve. If oil seeps into the connector, over time, the Check Engine lamp may illuminate and set various AVCS-related DTCs.
07-150-19
This bulletin provides a procedure for replacing the rear combination lamp wiring harness. The harness is now available as a service part separate from the lamp assembly.
16-120-19
This bulletin provides a procedure to follow for addressing customer concerns of a shuddering condition or chattering -type sound heard or felt when making sharp turns. If an applicable vehicle presents with the condition as described, it is recommended to perform the transfer clutch break-in procedure as described.
02-178-18R
This Service Information bulletin announces a design change made to the rubber timing hole access plug to improve its retention and prevent water intrusion into the converter case.
02-134-12R
The purpose of this bulletin is to announce a change to the specification of the valve springs used in the FB engine. The new springs have different color paint marks to help identify their application.
16-119-19
This Service Information bulletin announces availability of a new control valve assembly (valve body) designed to prevent false detection of DTC P0841 and / or illumination of the AT Temp light. Testing has revealed in some limited cases, air bubbles (aerated fluid) may enter certain pressure circuits within the control valve assembly causing fluid pressure control and adjustment to be calculated incorrectly resulting in DTC P0841. The shape of these circuits has been changed to prevent this occurrence.
06-68-19
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. This will prevent the pad from dragging due to corrosion buildup which may result in uneven or premature wear of the replacement brake pads. This additional instruction applies to all models with brake pads using the upper and lower pad clips and has been added to the brake pad installation procedures found in the related Service Manuals.
07-146-19
This bulletin announces a design change made to the engine wiring harness to improve resistance to moisture. A detailed illustration describing the change is supplied below.
07-133-18
This Service Information Bulletin announces design changes to the engine?s knock sensor which will help improve vehicle assembly line efficiency and increase durability. In some cases, the Check Engine light may illuminate and a knock sensor-related DTC set in the ECM memory: P0327, P0328, P0332 and P0333. The knock sensor for DIT engines is now utilized for NA engines to improve durability and resistance to heat.
03-82-18
This Service Information bulletin announces a design change to the clutch release bearing used on the models as listed above. During assembly of the bearing, a different type of grease is used which has a higher resistance to heat. In cases where the operator keeps a foot on the clutch pedal for extended periods, an increased amount of heat is generated which can cause the grease inside the bearing to deteriorate. In a case of prolonged clutch pedal application, seizure of the bearing can occur with potential damage to other related components.
03-79-18R
This bulletin announces a change to the clutch system components optimizing their durability and resistance to certain severe driving conditions including high-temperature operation.
06-66-18
This Service Information bulletin announces a design change made to the front brake rotors used on the models listed above. The change makes it easier to identify these parts from those used on other models.
12-251-18
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully.There is a latch to keep the glove box closed on both sides of the glove box door. If the door is closed without using enough force to engage both latches or by pushing it shut on just one side instead of in the middle, one may close and not the other. Over time, if the door is not fully closed with both latches, high cabin temperatures along with weight of the items inside the glove box may cause the assembly to deform slightly and a gap to develop.
10-86-17R
A design change was made to the blower motor assembly to address the following customer concerns: ? Blower fan is either inoperative or only operates on high speed. ? Excessive rotational-type sound heard when the fan is operating.
06-65-18
This bulletin announces a new Vehicle Dynamics Control (VDC) Module and Hydraulic Control Unit (VDCCM&HCU). The new part was designed to address a small number of customer concerns regarding a clicking or ticking-type sound heard coming from the driver?s side footrest area. The new modules incorporate logic with enhanced internal solenoid and motor control characteristics.
07-128-18R
This Service Information bulletin provides a measurement and adjustment procedure for the stop lamp switch. An improperly adjusted (or faulty) stop lamp switch can cause any of the DTCs listed above to set and result in the related system?s warning lamp to illuminate.
16-115-18
In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Powertrain Warranty coverage for the Continuously Variable Transmission (CVT) on the above listed models and model years from the original five (5) years or sixty thousand (60,000) miles (whichever comes first) to ten (10) years or one-hundred thousand (100,000) miles (whichever comes first). This change is not in response to any specific condition, rather it is to provide customers with added assurance regarding the function and overall performance of their CVT. Additionally, vehicles which are beyond one-hundred thousand (100,000) miles at the time customer notification letters are mailed are being offered additional coverage for a period of one-year from the date of the customer notification letters.
02-178-18
This Service Information bulletin announces a design change made to the rubber timing hole access plug to improve its retention and prevent water intrusion into the converter case.
15-232-18
This Service Information bulletin announces a change made to the lens portion of the fog light assembly. The new lens has optimized light distribution characteristics while remaining interchangeable with the original type.
07-139-18R
This bulletin outlines a design change made to the inner lens extension portion of the LED headlamp assembly. Under the right conditions, the shape of the lens for the actual head lamp light source can cause sunlight to be focused onto the extension portion of the lens resulting in deformation. A heatresistant shade has been added to protect the affected area.
12-234-18
This bulletin provides a repair procedure for replacing the foam cushion installed between the top front edge of the IP and the windshield glass. Use the supplied Service Procedure to address a customer concern involving the foam cushion becoming visible above the IP near the defroster vent outlets.
06-63-18R
This bulletin announces a design change to the EPB adapter cord harness connector. In some cases, the retaining tab of the connector may become damaged as a result of removal or installation for diagnosis and later and cause DTC C1956 or C1957 to set and the brake warning lamp to illuminate. The retaining tab portion of the connector has been changed to improve its durability and prevent recurrence of the DTC. If there is no prior history of disconnection and the connector lock tab is not damaged, check for another possible cause for these DTCs.
12-201-16R
IMPORTANT: This Service Bulletin has been as been replaced by TSB 12-243-18 dated 6/6/2018 entitled ?Paint Chipping between Hood Grille (Scoop) and Hood?. Please refer to this new bulletin for the latest information regarding this condition.
12-243-18
This bulletin replaces TSB 12-201-16R and provides a new repair procedure to address customer concerns of the hood scoop scrubbing the finish of the hood panel in the areas shown in the photo. Due to different expansion rates between the metal hood panel and the resin material used for the hood scoop, the edges of the scoop?s rear corners may come in contact with the hood panel and abrade the finish.
10-88-18
This bulletin announces a change made to the Automatic Climate Control Head Assembly. The change will address concerns where the temperature selected for cooling ?feels? warmer to the customer than the temperature displayed. The new programming will adjust the threshold for when cooling occurs to improve the air conditioning system?s cooling effect making it more closely match the customer?s selected temperature.
12-241-18
4 DOOR MODELS ONLY. This bulletin announces a change made to the trunk lid lock (latch) assembly. The purpose of this change is to improve parts integration (or ?commonality?) between models. This change is not intended to address any specific customer concern.
15-222-18
This bulletin announces a design change to the A/C Condenser receiver-dryer assembly. The change involves the addition of a rubber end cap and retaining clip onto the bottom of the receiver-dryer tank portion to prevent corrosion intrusion and enhance sealing.
12-238-18R
This bulletin announces a design change to the front door checkers used on the models listed. The new checker mechanism provides a more ?positive feel? of the detents or check positions as the front doors are opened and closed.
07-134-18
This Service Information bulletin provides a new troubleshooting chart to use when diagnosing a DTC B1760 related to the Occupant Detection System (ODS). Following these diagnostic steps will help avoid unnecessary ODS sensor / seat cushion assembly replacement
06-61-18
This bulletin announces availability of new VDC Control Module & Hydraulic Units (VDCCM&H/U) to address isolated customer concerns of the green Hill Holder light blinking and cancel warning alarm sounding during cranking / starting the engine
18-192-18
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes.
12-231-18R
This bulletin announces a design change to the air vent grille located in the lower portion of the trunk (or cargo) area. The shutters of the vent grille are designed to open briefly and relieve cabin pressure when the doors are shut with the windows fully closed. The vent grilles have rubber ?shutters? which occasionally, may catch on the frame (case) portion and not close properly allowing outside air / odor to enter the cabin.
02-173-18
2.0L Turbo Models only. This bulletin announces availability of a special turbocharger air intake duct designed to prevent EXTREMELY RARE occurrence of ice formation from condensation in the duct?s PCV system passages.
F10-Gen2-NAV-15-
TECHNICAL SUPPORT GUIDE FOR NAVIGATION AND AUDIO F10 GEN2 SYSTEMS.
12-231-18
( 2017-2018MY Impreza - 5 Dr Only)
15-215-18
Models with FujitsuTEN (F10) Gen 2.0 / 2.1 Navigation or Display Audio Head Units ONLY. This bulletin provides a repair procedure to address specific, confirmed customer concerns of: ? Audio output interruption every 2-3 seconds when listening to AM or FM radio broadcasts ? No audio output at all when attempting to listen to a HD Radio broadcast.
UPDATE - Removal
The corrected update files are now available for download from Subarunet. TSB 15-20516R has been revised with new file names where applicable and re-posted to STIS.
11-174-17R
This bulletin announces the availability of reprogramming files to optimize the ECM and address the following customer concerns: ? Check Engine light coming on (with DTC P05A0 stored in memory). ? Potential battery discharge (dead battery) after repeated periods of short-trip driving. ? A high (or ?hanging?) engine RPM after depressing the clutch pedal (Forester only).
04-17-17R
This bulletin provides a service procedure to address isolated customer concerns of a rattling sound identified as coming from the Electronic Power Steering (EPS) rack assembly. The repair involves installation of a new tension spring for the worm gear to reduce / eliminate the condition. It should be noted the condition is NOT detrimental to the operation of the EPS system.
02-170-17
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. The new seal will eliminate potential oil seepage into the wire harness connector portion of the valve. If oil seeps into the connector, over time, the Check Engine lamp may illuminate and set various AVCS-related DTCs.
02-166-17R
This bulletin outlines design changes made to the upper oil pan assembly on FA and FB engines used on the models listed above. There have been isolated cases where the sealer used between the upper oil pan and the crankcase has become displaced resulting in engine oil seepage. Revisions made to the upper oil pan casting: * The mating flange thickness of the casting in the area identified as the cause for the seepage has been increased by 5.5mm. (See images provided in the Parts Information section below.) This thickness increase creates the need for a longer bolt to provide proper tightening and retention. * An additional mounting point has been added to the ribbing inside the casting to increase retention of the steel baffle plate and eliminate vibration.
07-118-17R
Models with SRVD Only. This bulletin provides revised diagnostic and repair procedures to address DTC B2327 for the Subaru Rear Vehicle Detection (SRVD), Blind-Spot Detection (BSD) and Rear Cross Traffic Alert (RCTA) system on the applicable models listed above. Under very specific (rare) conditions, the radar function of the SRVD system may experience a communication error and cause the SRVD warning lamp to illuminate. In addition, under certain highway driving conditions, an improper signal calculation by the system may cause a Cancel Code B2328 to set which will also cause the SRVD warning lamp to illuminate.
02-168-17
This Service Information bulletin announces a material change to the engine accessory drive / v-belt made to address customer concerns of a slipping belt (squeal or chirping) sound.
02-166-17
This bulletin outlines design changes made to the upper oil pan assembly on FA and FB engines used on the models listed above. There have been isolated cases where the sealer used between the upper oil pan and the crankcase has become displaced resulting in engine oil seepage.
1117117
This bulletin announces the availability of reprogramming files to optimize the ECM and address isolated customer concerns of a spark knock (engine ping) -type sound.
096516R
REVISED. This bulletin announces a design change of the fuel injector used on 2.0L DIT models to prevent water intrusion. A new silicone rubber cover has been developed and incorporated into production for this purpose.
169816
This bulletin announces availability of reprogramming files for optimization of the transmission control module (TCM). The new logic addresses customer concerns of inconsistent shifting characteristics and / or a ?slipping? -type sensation which may be experienced under moderate acceleration after a cold start before the CVT is up to operating temperature.
09-65-16
This bulletin announces a design change of the fuel injector used on 2.0L DIT models to prevent water intrusion. A new silicone rubber cover has been developed and incorporated into production for this purpose.
11-170-16
2.0L DIT Models only. This bulletin announces the availability of reprogramming files to optimize the ECM. These files will address a customer concern of the Check Engine Light illuminating as a result of DTC P2270 being stored in the ECM.
02-164-16
This Service Information bulletin announces a design change to the internal contact portion of the oil pressure switch to increase durability
09-64-16
This Service Information bulletin announces a change to the shape of the rubber cap used on the flange nuts securing the sub-level sending unit to the fuel tank. In addition, two of the caps are now used in production instead of only one. This change was made to enhance productivity during vehicle assembly.
16-103-16
Only Models Equipped with TR690 CVT only. This bulletin has been developed in response to a small number of customer concerns regarding fluid seepage found coming from the CVT assembly. Investigation has identified a likely source of the seepage to be the sealant used on the CVT's oil pump chain cover. The repair involves removal, a thorough cleaning and inspection of the sealing surfaces followed by re-sealing the cover.
15-207-16
This bulletin announces a design change to the USB connector inside the USB-AUX unit to address customer concerns of the USB cable becoming stuck and / or difficult to remove.
15-206-16
USB Device Not Recognized on Fujitsu-Ten (F10) 7? Display Navigation and Display Audio Units. This bulletin announces availability of a new auxiliary USB unit to address customer concerns where the 7? Display Audio or Audio Navigation head unit will not recognize USB devices connected via the auxiliary unit.
15-182-15R
IMPORTANT NOTE: Due to the extensive revisions made to the information originally contained in this bulletin, a new bulletin, 15-205-16 has been issued. Please refer to this new bulletin for the latest information regarding this condition.
15-198-16R
IMPORTANT NOTE: Due to the extensive revisions made to the information originally contained in this bulletin, a new bulletin, 15-205-16 has been issued. Please refer to this new bulletin for the latest information regarding this condition.
15-205-16
This bulletin announces new reprogramming file availability and the software installation procedure to address additional operational concerns received from the field and listed below involving ?Gen 2? F10 Navigation and Display Audio units with 7? display. The procedure will involve downloading the applicable software update files from Subarunet then loading them onto a flash drive for audio unit installation. It is important to read through and understand this information completely before proceeding. These latest software updates contain new logic to address the following concerns: ? Mirrorlink 1.1 updates ? Enable Mute function for Navigation guidance ? Incomplete display of intersection names in combination meter ? Increased accuracy of the XM Traffic information displayed ? Intermittent delay (approximately 1 minute) in display of map information after initial start-up of Navigation function (2015MY Legacy and Outback only).
12-189-15R
This bulletin provides information about changes made to the rear shelf trim to address customer concerns of a rattling sound heard while driving over bumpy / rough roads. The sources of the rattle have been identified as: ? the mounting points for the center stop lamp where it fits into the package shelf ? the package shelf itself rattling against the inside of the rear glass ? the rib and/or stand portions located on the underside of the package shelf contacting the shelf portion of the vehicle body.
12-207-16
This bulletin announces a change to the procedure used in production of the rear door glass assembly. The bottom edge of the door glass is pressed into a metal channel lined with rubber. The channel attaches the door glass assembly to the window regulator. In below-freezing temperature conditions, water freezing in the channel combined with the door glass sticking to the door weatherstrip can increase chance of the glass separating from the channel when attempting to operate (lower) the window. A lubricant has been added to the rubber portion to insure the glass gets fully seated during assembly which maximizes the clamping force of the channel on the glass.
078815R
This Service Information bulletin provides a procedure to use when installing a SOA821B200 replacement battery in a 2015MY WRX (2.0L). The sensor located on the battery ground terminal interferes with the battery vent cap used on the replacement battery.
216316
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. The applicable Service Manuals will be revised with this new information in the near future.
12-206-16
All Models Listed with Seat Lifter Feature. This bulletin provides a procedure to address a customer reported cosmetic condition of surface rust appearing on the inner seat cushion frame of the front seat assemblies.
07-111-16
This bulletin announces a design change to the headlamp assembly to improve sealing and prevent moisture intrusion. This condition may result from a slight misalignment of the attaching points during the headlamp assembly process. An improved sealing material is now being used for bonding the outer lens to the housing.
10-84-16R
This bulletin announces the availability of a new Air Conditioning compressor / clutch assembly to address customer concerns of the system not operating. Electrical windings located inside the clutch assembly have been changed to eliminate the condition. The service procedure will involve replacement of the A/C compressor and clutch as a complete assembly.
12-201-16
Paint Chipping between Hood Grille (Scoop) and Hood - This new bulletin replaces TSB 12-186-15 and announces a new repair procedure to address customer concerns of the hood scoop scrubbing the finish of the hood panel in the areas shown in the photo below. Due to different expansion rates between the metal hood panel and the resin material used for the hood scoop, the edges of the scoop?s rear corners may come in contact with the hood panel and abrade the finish.
15-200-16
Models with Fujitsu-TEN / FTEN / (F10) Gen2 Navigation System only. Fujitsu-TEN / FTEN / (F10) Navigation: Voice Recognition Concerns with Finding Addresses in Some Metro Areas.
15-199-16
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field and listed below involving the Clarion Display Audio unit with 6.2? display. The procedure will involve downloading the applicable software update files from Subarunet then loading them onto a flash drive for audio unit installation.
18-186-16
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes.
15-198-16
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field listed below involving ?Gen 2? F10 Navigation and Display Audio units with 7? display. The procedure will involve downloading the applicable software update files from Subarunet then loading them onto a flash drive for audio unit installation. It is important to read through and understand this information completely before proceeding.
15-177-14M2
When ordering exchange units from Fujitsu Ten through their online web site, some new information will soon be requested and in some cases required. To assist with that, a new Bluetooth Interview Form is available to facilitate the completion of an exchange order. The form is available on Subarunet at Service Operations & Technical >> Forms.
15-197-16
Although Fujitsu TEN (F10) Navigation units utilize an externally (faceplate) accessible MicroSD memory card, the MicroSD card used in Clarion display audio units is internal and not accessible. In the event a ?Check SD Memory Card? alert message appears on the faceplate display, an exchange display audio unit must be ordered through the applicable Clarion audio exchange procedure.
12-182-15R
This bulletin announces availability of a new front door checker mechanism designed to hold the doors more securely when they are in partially open / closed positions. An additional detent position has also been added.
10-84-16
This bulletin announces the availability of a new Air Conditioning compressor / clutch assembly to address customer concerns of the system not operating. Electrical windings located inside the clutch assembly have been changed to eliminate the condition. The service procedure will involve replacement of the A/C compressor and clutch as a complete assembly.
05-61-16
This bulletin announces a design change to the front strut mounts intended to address customer concerns of a popping-type sound which may be heard when making low speed turns.
15-177-14M
When ordering exchange units from Fujitsu Ten through their online web site, some new information will soon be requested and in some cases required. Exchange order entry will now request a date and time when condition was last duplicated. The customer?s phone carrier, phone make and model will be required when Bluetooth or Connectivity failure sections are selected.
WTA-62
Turbo models only. Subject: Update ? Subaru Safety Recall Campaign/ STOP SALE: WTA?62 Turbo Engine Air Intake Duct. Owner Notification: All potentially affected vehicle owners will be notified by first class mail on or around April 15, 2016. As previously announced on March 17, 2016, Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Forester 2.0XT and WRX vehicles due to a possible issue with the turbocharger air intake duct.
WTA-62A
Turbo models only. Service Procedure Bulletin. The repair procedure will involve inspecting and possibly replacing the turbocharger air intake duct. Inspection of the turbocharger air intake duct lot number (date) molded on the duct will be necessary to determine if replacement is required.
WTA-62SS
Subaru Safety Recall Campaign/ STOP SALE: WTA?62 Turbo Engine Air Intake Duct. The turbocharger air intake duct on affected vehicles may have been produced with incorrect material that is susceptible to cracking.
07-106-16
This bulletin announces a change to the battery sensor to prevent unnecessary occurrence of DTC P1C00 being set / stored in the ECM memory.
09-63-16
THIS SERVICE INFORMATION BULLETIN SERVES AS A REMINDER TO ALWAYS FOLLOW THE PROPER PROCEDURES WHEN DIAGNOSIS OF A DTC B1500 LEADS TO REPLACEMENT OF A FAULTY MAIN AND / OR SUB FUEL LEVEL SENSOR.
16-98-16
THIS BULLETIN ANNOUNCES AVAILABILITY OF REPROGRAMMING FILES FOR OPTIMIZATION OF THE TRANSMISSION CONTROL MODULE (TCM). THE NEW LOGIC ADDRESSES CUSTOMER CONCERNS OF INCONSISTENT SHIFTING CHARACTERISTICS AND / OR A SLIPPING -TYPE SENSATION WHICH MAY BE EXPERIENCED UNDER MODERATE ACCELERATION AFTER A COLD START BEFORE THE CVT IS UP TO OPERATING TEMPERATURE.
Tech tips
This is the final PDF for the 2016 January TechTIPS, please use and distribute as needed.
F10TSG
TECHNICAL SUPPORT GUIDE - GEN 2.0 & 2.1 MICRO SD NAVIGATION (AVN) DISPLAY AUDIO (DA)
12-195-15
SHOULD YOU RECEIVE A CUSTOMER CONCERN OF VIBRATION OR LOOSENESS IN EITHER OF THE DOOR MIRRORS, A DESIGN CHANGE HAS BEEN MADE TO THE 3 MIRROR HEAD MOUNTING HOLES IN THE MOUNTING BASE. IN ADDITION, A NEW RETAINING BOLT AND TIGHTENING TORQUE SPECIFICATION ARE NOW USED TO SECURE THE MIRROR HEAD TO THE MOUNTING BASE. THIS BULLETIN PROVIDES A PROCEDURE FOR REPAIRING THE EXISTING MIRROR ASSEMBLY BY REPLACING THE THREE MOUNTING SCREWS WITH UPDATED FASTENERS. NOTE: REFER TO TSB 12-152-13 DATED 6/17/2013 FOR RELATED INFORMATION ON BRZ MODELS.
07-100-15
THIS BULLETIN ANNOUNCES THE AVAILABILITY OF REPROGRAMMING FILES FOR THE EYESIGHT SYSTEM TO PROVIDE PROPER FUNCTION OF THE VEHICLE INFORMATION REGISTRATION MENU. IN RARE CASES, WHEN ATTEMPTING TO PERFORM THE CAMERA INITIALIZATION PROCEDURE AFTER REPAIR OR REPLACEMENT, IT CANNOT BE COMPLETED BECAUSE THE REQUIRED VEHICLE INFORMATION REGISTRATION MENU CANNOT BE DISPLAYED.
18-183-15
THE PURPOSE OF THIS BULLETIN IS TO PROVIDE A DESCRIPTION OF CURRENT CHANGES TO SERVICE MANUALS AVAILABLE VIA THE SUBARU TECHNICAL INFORMATION SYSTEM (STIS) WEB SITE. THE TABLES CONTAINED WITHIN THIS BULLETIN ARE TO BE USED AS GUIDES FOR BECOMING AWARE OF THE LATEST CHANGES. WE ADVISE YOU TO ALWAYS REFER TO THE STIS WEB SITE WHEN LOOKING FOR THE LATEST SERVICE INFORMATION. PRINTED PAGES WILL NOT BE MADE AVAILABLE TO UPDATE PRINTED SERVICE MANUALS. PAPER MANUALS MAY HAVE DIFFERENT PAGE NUMBERING THEN WHAT IS REFLECTED BELOW, BASED ON MULTIPLE NEW AND REVISED PAGES. PLEASE REFER TO THE INFORMATION CONTAINED ON THE STIS WEB SITE FOR ALL FUTURE, UPDATE SERVICE MANUAL INFORMATION.
12-190-15R
THIS BULLETIN PROVIDES A PROCEDURE TO ADDRESS CUSTOMER CONCERNS OF A CREAKING SOUND HEARD WHEN OPERATING THE CLUTCH PEDAL. THE CAUSE OF THE SOUND HAS BEEN IDENTIFIED AS A VERY SLIGHT AMOUNT OF MOVEMENT BETWEEN THE 2 LAYERS OF METAL (CIRCLED IN YELLOW) WHICH FORM THE SPECIFIC CLUTCH AND BRAKE PEDAL ASSEMBLY MOUNTING BRACKET SHOWN IN THE ILLUSTRATION AND PHOTOS BELOW.
07-99-15
ON SOME VEHICLES, A CUSTOMER MAY NOT BE ABLE TO ACCESS THE KEYLESS BUZZER VOLUME FUNCTION ON THE MULTI-FUNCTION DISPLAY (MFD). THIS BULLETIN ANNOUNCES AVAILABILITY OF REPROGRAMMING FILES FOR THE BODY INTEGRATED UNIT (BIU) TO FACILITATE SETTING THE VOLUME OF THE KEYLESS BUZZER VIA THE MFD.
08-39-15
THIS SERVICE INFORMATION BULLETIN PROVIDES A PROCEDURE FOR RESETTING THE LIFETIME FUEL CONSUMPTION FUNCTION OF THE MFD. WHENEVER REPLACING THE MFD AND / OR COMBINATION METER, THE LIFETIME FUEL CONSUMPTION FUNCTION OF THE MFD MUST BE RESET FOR ACCURATE INFORMATION TO DISPLAY GOING FORWARD. IF NOT RESET, ERRONEOUS VALUES (EITHER EXTREMELY HIGH IN THE CASE OF A MFD REPLACEMENT OR EXTREMELY LOW FOR A COMBINATION METER REPLACEMENT) FOR LIFETIME FUEL CONSUMPTION WILL BE DISPLAYED. THERE IS NO WAY TO TRANSFER THE OLD / EXISTING LIFETIME FUEL CONSUMPTION RESULTS TO THE NEW MFD OR COMBINATION METER ALLOWING IT TO CONTINUE UNINTERRUPTED. AS A RESULT, AFTER REPLACEMENT OF THE MFD AND / OR COMBINATION METER, ALL CALCULATIONS WILL START FRESH FOLLOWING PERFORMANCE OF THE FOLLOWING PROCEDURES.
F10 Tehnical Sup
Tehnical Suppurt Guide Gen 2.0 & 2.1 Micro SD Navigation (AVN) Gen 2.0 & 2.1 Display Audio (DA)
02-162-15R
THIS SERVICE INFORMATION BULLETIN ANNOUNCES A DESIGN CHANGE TO THE OIL PRESSURE SWITCH ASSEMBLY. NICKEL PLATING HAS BEEN APPLIED TO THE INTERNAL SWITCH CONTACTS TO ENHANCE THEIR DURABILITY AND REDUCE THE POSSIBILITY OF POOR CONTACT WHICH COULD AFFECT OPERATION OR CAUSE IMPROPER ILLUMINATION OF THE OIL PRESSURE WARNING LAMP. A SMALL PILOT PORTION WAS ADDED TO THE THREADED AREA ON P.N. 25240KA051 AS SHOWN IN THE ILLUSTRATION BELOW. REVISED PRODUCTION CHANGE INFORMATION.
02-162-15
THIS SERVICE INFORMATION BULLETIN ANNOUNCES A DESIGN CHANGE TO THE OIL PRESSURE SWITCH ASSEMBLY. NICKEL PLATING HAS BEEN APPLIED TO THE INTERNAL SWITCH CONTACTS TO ENHANCE THEIR DURABILITY AND REDUCE THE POSSIBILITY OF POOR CONTACT WHICH COULD AFFECT OPERATION OR CAUSE IMPROPER ILLUMINATION OF THE OIL PRESSURE WARNING LAMP. A SMALL PILOT PORTION WAS ADDED TO THE THREADED AREA ON P.N. 25240KA051 AS SHOWN IN THE ILLUSTRATION BELOW.
18-182-15
THE PURPOSE OF THIS BULLETIN IS TO PROVIDE A DESCRIPTION OF CURRENT CHANGES TO SERVICE MANUALS AVAILABLE VIA THE SUBARU TECHNICAL INFORMATION SYSTEM (STIS) WEB SITE. THE TABLES CONTAINED WITHIN THIS BULLETIN ARE TO BE USED AS GUIDES FOR BECOMING AWARE OF THE LATEST CHANGES. WE ADVISE YOU TO ALWAYS REFER TO THE STIS WEB SITE WHEN LOOKING FOR THE LATEST SERVICE INFORMATION. PRINTED PAGES WILL NOT BE MADE AVAILABLE TO UPDATE PRINTED SERVICE MANUALS.
WQS-54U
OWNER NOTIFICATION - SUBARU RECALL CAMPAIGN: WQS-54 DRIVER ASSIST SYSTEM (EYESIGHT) DELAY IN WARNING INDICATOR OWNER NOTIFICATION SUBARU WILL NOTIFY POTENTIALLY AFFECTED VEHICLE OWNERS BY FIRST CLASS MAIL. OWNER NOTIFICATION WILL BEGIN ON JULY 20, 2015. EMAILS WILL ALSO BE SENT TO AFFECTED OWNERS WITH A VALID EMAIL ADDRESS ON FILE WITH MYSUBARU.COM.
SB-WQS-54
SUBARU: TSB CONTAINS AN OWNER'S NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. IN CERTAIN VEHICLES THERE IS A DELAYED IN DETECTING A FAILURE OF BRAKE LAMP SWITCH (BLS) BY DRIVER ASSIST SYSTEM AND TAKES LONGER FOR VEHICLE DYNAMIC CONTROL (VDC) TO RECEIVE REQUEST, RESULTING IN NO AUTOMATIC BRAKING. MODEL 2015 LEGACY, OUTBACK, IMPREZA, XV CROSSTREK, 2016 WRX. *PE
WQS 54U
The WQS?54 Repair Procedure Bulletin has been posted on STIS. Coverage information for all affected Stop?Sale vehicles is available on subarunet.com. Subaru of America, Inc. (Subaru) is recalling certain vehicles equipped with a driver assist system: ? 2015 model year Legacy vehicles ? 2015 model year Outback vehicles ? 2015 model year Impreza vehicles ? 2015 model year XV Crosstrek vehicles ? 2016 model year WRX vehicles The programming of the driver assist system will not detect a fault in one of the associated system components. In the event of brake lamp switch (BLS) failure, the Vehicle Dynamic Control (VDC) correctly detects the BLS failure, but the driver assist system will be delayed in detecting the BLS failure.
WQS-54RP
Subaru of America, Inc. (SOA) is recalling certain 2015 model year Subaru Legacy, Subaru Outback, Subaru Impreza (4Door and 5Door) and Subaru XV Crosstrek vehicles and certain 2016MY Subaru WRX vehicles equipped with a Driver Assist System. The programming of the Driver Assist System will not detect a fault in one of the associated system components. In the event of Brake Lamp Switch (BLS) failure, the Vehicle Dynamic Control (VDC) correctly detects the BLS failure, but the Driver Assist System will be delayed in detecting the BLS failure. Therefore, it will take longer for the multi information display to inform the driver of a malfunction. In addition, VDC will not receive the brake request from the Driver Assist System, resulting in no automatic braking, including Adaptive Cruise Control and PreCollision Braking.
WQS-54 Recall
New Subaru Recall Campaign: WQS-54 Driver Assist System Delay in Warning Indicator. The programming of the driver assist system will not detect a fault in one of the associated system components. In the event of brake lamp switch (BLS) failure, the Vehicle Dynamic Control (VDC) correctly detects the BLS failure, but the driver assist system will be delayed in detecting the BLS failure.
WQS-54A
Subaru of America, Inc. (Subaru) is recalling certain vehicles equipped with a driver assist system The programming of the driver assist system will not detect a fault in one of the associated system components. In the event of brake lamp switch (BLS) failure, the Vehicle Dynamic Control (VDC) correctly detects the BLS failure, but the driver assist system will be delayed in detecting the BLS failure.
Announcement
New Vehicle Receipt- Navigation SD Card Transit Storage Location Change
0116809R
Replacement Key and Immobilizer Info
171713R
Event Data Recorder (EDR) Function of Airbag Module
Announcements-2
Effective with all 2015 model year cars and forward, the oil change interval is changing to 6,000 miles or 6 months, whichever comes first.
0214013
Oil Filler Cap Gasket Coming Unseated
WQE41-1
Puddle Light Recall
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.