Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
15-308-23R
This Service Information Bulletin outlines a systematic procedure for diagnosing parasitic draw (dark/standby current) in vehicles experiencing battery drain when the ignition is off, leading to no-start conditions or frequent jump-starts.This is an revised version of the original bulletin.
15-304-22R
This Bulletin has been developed to outline the steps for gathering basic but essential information during diagnosis of Infotainment concerns. (This is an revised version of the original bulletin.)
Article Locator
Techtips newsletter locator index.
15-333-25R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. This is an revised version of the original bulletin
02-193-24R
This bulletin provides updated parts information and a service procedure to follow for removing accumulated carbon deposits from fuel injectors and internal engine components (e.g. intake valves and / or manifold, and combustion chambers). (This is an revised version of the original bulletin.)
09-74-21R
This bulletin provides updated parts information and a service procedure to follow for removing accumulated carbon deposits from fuel injectors and internal engine components (e.g. intake valves and / or manifold, and combustion chambers). (This is an revised version of the original bulletin.)
SubaruNet Annoucement (E
This announcement is requesting retailer staff to retain the EyeSight protective hood covers from Generation 4 EyeSight cameras.
01-167-08R
This bulletin contains additional information for recommended materials listed in the Service Manuals for individual models.
SubaruNet Announcement (R
This announcement provides information on the remanufactured CVT transmission program.
18-230-26
This bulletin announces the diagnostic procedures to be used when DTCs B1571(REFERENCE CODE INCOMPATIBILITY IMMOBILIZER CM TO ECM) and B1572(IMM CIRCUIT EXCEPT ANTENNA CIRCUIT) are detected by Keyless Access with Push Button Start(KACM).
07-240-26R
This Service Information Bulletin was developed to provide interim guidance for vehicles exhibiting DTC B2A20.
03-97-26
This bulletin announces the service manual correction regarding clutch master cylinder reservoir service procedures.
05-97-26
This Bulletin provides the diagnostic procedures to be followed when addressing customer concerns of steering wheel/vehicle body vibration when driving at highway speeds when tire/wheel balance is suspected.
10-105-25R
This bulletin announces the new procedure and Warranty Fail Code for FirstTime air conditioning (A/C) performance concerns possibly resulting from an undetected A/C refrigerant leak.
15-219-18R
This bulletin contains information to help when attempting to complete the STARLINK Telematics subscription process, an Error Code 202 and / or 204 may occur preventing the process from completing successfully
SubaruNet Announcement (A
This announcement provides information on the use of aftermarket services or tools for programming immobilizer keys/fobs.
Subaru Tech Tips Special
This Subaru service and technical support line newsletter provides information on the next phase of TechShare.
15-300-22R
This Bulletin provides the diagnostic procedure for the STARLINK® Remote Engine Start (RES).
Subarunet Announcement (E
This announcement has been created to address difficulties with software updates on Subaru Select Monitors with DST-010 interface firmware has been updated.
05-84-21R
This bulletin announces availability of new front wheel hub assemblies incorporating bearing surfaces having increased resistance to imperfections resulting from shock loads.
18-226-25R
This Service Information Bulletin provides the Service Manual Correction to the diagnostic procedure for DTC B2A16 (Immobilizer Key Collation Diagnosis).
18-228-25R
This bulletin announces the diagnostic procedures to be used when DTCs P2096 (POST CATALYST FUEL TRIM SYSTEM TOO LEAN BANK 1) and P2097 (POST CATALYST FUEL TRIM SYSTEM TOO RICH BANK 1) are detected by the Engine Control Module (ECM).
15-333-25
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
18-228-25
This bulletin announces the diagnostic procedures to be used when DTCs P2096 (POST CATALYST FUEL TRIM SYSTEM TOO LEAN BANK 1) and P2097 (POST CATALYST FUEL TRIM SYSTEM TOO RICH BANK 1) are detected by the Engine Control Module (ECM).
Subaru Tech Tips (Article
Subaru service article locator.
15-130-08R
This bulletin provides information on the load carrying capacity reduced label when a port-installed or retailer-installed accessory exeeds 1.5 percent of the GVWR or 100 pounds, which ever is lower.
07-233-25R
This Bulletin provides details on a new formal testing, charging, and tracking procedure for all 12-volt batteries in new vehicle inventory.
07-236-25
This Bulletin outlines a comprehensive update to the dark current/parasitic draw diagnosis & testing procedures.
07-233-25
This Bulletin provides details on a new formal testing, charging, and tracking procedure for all 12-volt batteries in new vehicle inventory wjhich must be tested and reported every 30 days.
15-266-20R
This Bulletin provides helpful procedures and best practices to utilize when customers present with concerns relating to the operation of their Gen 2/Gen 3 Telematics system equipped Subaru.
15-320-24R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
SubaruNet Announcement
Subaru of America, Inc. will release an OTA to perform a software update to the DCM. This is a preventive OTA.
09-131-25R
This bulletin announces the diagnostic procedures and availability of reprograming files to rectify the following Diagnostic Trouble Codes (DTCs). • P2404: EVAP System Leak Detection Pump Sense Circuit Range/Performance. • P0420: Catalyst System Efficiency Below Threshold Bank 1. (not applicable for 15-18 models)
13-108-25
This bulletin provides information on paint codes for vehicles in the 2026 line up.
Subaru Service Technical
Subaru Service Technical Support Newsletter special edition.
WRA-25R
In the interest of customer satisfaction, Subaru of America, Inc. (Subaru) is initiating a new voluntary emissions recall for certain 2017 model year WRX and Forester vehicles equipped with a 2.0L turbo engine.
SubaruNet Annoucement
This announcment provides information on the release of the latest software updates to the Subaru Midtronics DSS-5000 Battery Diagnostic tool.
SubaruNet announcement
Subaru of America, Inc. (Subaru) is initiating a new voluntary emissions recall for certain 2017 model year WRX and Forester vehicles equipped with a 2.0L turbo engine.
WRA-25
In the interest of customer satisfaction, Subaru of America, Inc. (Subaru) is initiating a new voluntary emissions recall for certain 2017 model year WRX and Forester vehicles equipped with a 2.0L turbo engine.
15-251-19R
This Bulletin provides additional diagnostics to follow when addressing a Telematics-related DTC B2A16.
SubaruNet Announcement (S
This announcement is to bring attention to the OTA for In-vehicle service appointment scheduler and In-vehicle message center.
01-168-09R
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site.
02-192-24R
This Bulletin announces the diagnostic procedures to be followed when diagnosing engine oil leakage on FA and FB type engines.
03-96-25
This bulletin announces design changes made to the rear axle hubs. These changes have been implemented to reduce cases water intrusion further leading to harmonic, humming, and grinding type sounds heard from the axle hub while driving.
14-31-25
This Bulletin announces availability of a User Guide and an informative video to supplement the recent releases to retailers of the SOA321152 and SOA321153 Terminal Test Kits.
09-51-08R
The purpose of this bulletin is to advise of SOA’s revised Catalytic Converter Recycling Program shipping procedure.
16-103-16R
This bulletin has been developed in response to a small number of customer concerns regarding fluid seepage found coming from the CVT assembly.
15-317-24R
In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the Data Communication Module (DCM) Warranty from 3 years (36 months) of 36,000 miles to 8 years (96 months) or 100,000 miles, whichever comes first.
Subarunet Announcement
This announcement is in regard to special service tool shipment will be shipped directly to the Subar retailers during February.
RC5 Head Unit OTA
A head unit OTA will be available via cellular network for Mid and High Grade CP1.5 head units.
02-193-24
This bulletin provides updated parts information and a service procedure to follow for removing accumulated carbon deposits from fuel injectors and internal engine components (e.g. intake valves and / or manifold, and combustion chambers).
07-59-07R
This bulletin is for information purposes only.The bulletin adresses design changes of the headlamps and rear combination lamps, where moisture and or condensation may develop on the inside of the lamp lenses.
15-312-23R
This bulletin announces repair procedures to be used when diagnosing dark current draw (parasitic draw) on vehicles equipped with Gen 1 Data Control Modules.
15-298-22R
This Service Information Bulletin announces the preferred practices to be used when handling vehicles equipped with Gen2 Telematics which are enrolled in the Subaru STARLINK® Security Plus Service featuring Stolen Vehicle Recovery Plus with Immobilizer.
02-192-24
This Service Information Bulletin announces the diagnostic procedures to be followed when diagnosing engine oil leakage on FA and FB type engines.
07-178-21R
This Service Information bulletin is being released as guidance for proper testing and charging of vehicle batteries.
15-320-24
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
02-191-22R
This bulletin announces availability of the NEW genuine Subaru engine oil filter.
15-316-24R
This bulletin announces the procedures required to reprogram the DCM (Data Communication Module) in Gen1 Subaru vehicles in response to the 3G network sunsetting.
03-94-24
This bulletin outlines the judgment criteria to be used when inspecting front transverse link bushings to reduce unnecessary bushing replacement.
Thermo Control Valve Vide
This thermo control valve video contains information on the replacement of thermo control valve.
13-107-24
This Bulletin provides SOA paint codes to help eliminate possible confusion for 2025 MY vehicles.
05-91-24
This Bulletin provides guidance for diagnosing a leaking front or rear suspension strut.
06-90-24
This bulletin provides diagnosis and procedure information to be applied when diagnosing potential fluid leaks on front and rear brake calipers. This information has been developed to reduce unnecessary brake caliper replacement.
16-112-18R
This bulletin announces a design change to the CVT select lever (shifter) mechanism in response to isolated customer concerns of not being able to remove the key from the ignition switch when the vehicle is in Park.
FAQ 15-317-24R
T16 Warranty Extension (15-317-24R) Frequently Asked Questions.
15-321-23R
This bulletin provides a repair procedure when diagnosing dark current draw on vehicles with GEN 1 Data Control Modules.
Subaru notice to
This letter provides information regarding the warranty extension for the Telematics Data Communications Module (DCM).
SubaruNet Announ
This announcement provides information in regard to the extension of the basic new car limited warranty for the Telematics Data Communication Module (DCM). This coverage will apply to the vehicles listed for vehicles sold or leased in the United States.
15-316-24
This bulletin provides procedures required for reprogramming the Data Communication Module (DCM) in Gen 1 Subaru vehicles due to sunsetting of the 3G network.
15-317-24
Subaru of America, Inc. (Subaru) is extending the Data Communication Module (DCM) warranty from three years (36 months or 36K miles) to eight years (96 months or 100K miles), whichever comes first. This extension is in light of the rare cases of dead batteries experienced by customers.Â
07-207-22R
In the interest of customer satisfaction, Subaru of America, Inc. is extending the New Car Basic Warranty coverage for the 12 Volt batteries used in the above listed models and model years beyond the original three (3) years or thirty six thousand miles (36,000), whichever comes first.
18-231-23
This Bulletin announces additional information regarding error codes 1403- 1407 encountered when attempting an adjustment/calibration of the EyeSight® system after body repair procedures have been performed.
15-285-21R
This Bulletin provides reference tables and photos to use for determining the infotainment head unit supplier and generation.
12-249-23R
This bulletin announces the recommended cleaning procedures to followed when encountering vehicles with long time exposure to pollen on painted surfaces on vehicles imported from Japan. This bulletin does not apply to SIA built vehicles.
02-131-12R
The purpose of this Bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the timing chain cover, front camshaft cap, camshaft carrier and / or upper oil pan.
06-87-22R
In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Warranty coverage for the electronic connector lock tab for the Electric Parking Brake (EPB) assembly used in the listed models.
03-78-17
This bulletin announces a design change to the clutch release bearing.
16-131-20R
This Service Information Bulletin provides an updated diagnostic flow along with an IMPORTANT caution to follow for certain CVT solenoid related DTCs as listed.
Subarunet Announ
In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is announcing an extension to the Basic New Car Limited Warranty for the Electronic Parking Brake (EPB) connector lock tab for certain 2015-2018MY Legacy, Outback & WRX models equipped with automatic transmissions.
5-88-21R
This bulletin announces a design change made to the front stabilizer bushings.
15-302-22
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
18-207-22
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
Subaru Tech Tips
Special Edition, 2012 current model subaru evaporative diagnostics and smoke testing.
15-298-22
This Bulletin announces the preferred practices to be used when handling vehicles equipped with Gen2 Telematics which are enrolled in the Subaru STARLINK® Security Plus Service featuring Stolen Vehicle Recovery Plus with Immobilizer.
05-88-21
This bulletin announces a design change made to the front stabilizer bushings.
12-288-20R
This bulletin announces a design change made to the Slide Rail components of the left and right front power seat frame / track assembliesd.
12-203-16R
This bulletin provides a procedure to address customer concerns of a squeaking sound originating from where the front seat belt buckle assembly attaches to the seat frame.
18-220-22
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
15-192-22R
This bulletin has been developed to outline the steps for gathering basic essential information during diagnosis and repair of the Infotainment concerns. (Applicable to all models with Harman or Denso CP1 Infotainment).
15-291-22
Going forward when a customerâs vehicle is equipped with a DCM that does not have Software version ID DCM_06.00.17_20190816 installed and they wish to subscribe to Starlink Telematics Service, the DCM must be replaced.
02-189-22
This Bulletin announces design changes to the engine oil and CVT fluid drain plugs.
16-102-16R
This bulletin provides a new flow chart and additional diagnostic tools to assist technicians with troubleshooting DTC P0841- SECONDARY OIL PRESSURE SENSOR PERFORMANCE.
05-79-20R
This bulletin announces a change made to the wheel lug nuts.
15-195-16R
This bulletin provides important information regarding diagnosis and replacement (when applicable) of the STARLINK Telematics Data Communication Module (DCM) along with a new claim submission requirement.
07-200-21
This bulletin announces the design changes to the right front wheel apron.
09-78-21
This bulletin announces the availability of Engine Control Module (ECM) reprograming files to correct DTC P015A and/or P015B.
15-208-17R
This bulletin announces availability of an enhancement to the Gracenote database included in the vehicles listed equipped with F10 7â Navigation and 7â Display Audio head units.
18-212-21
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
15-177-14R
This bulletin provides information to help diagnose and address different conditions relating to customer concerns which may arise when operating the new-generation âGen 2â and âGen 2.1â F10 Navigation and Display Audio systems.
15-280-21R
Gen1 Telematics Reprogramming for 3G Sunset.
02-187-21
This bulletin outlines changes in the service procedure for engine oil pressure inspection.
18-210-21
Description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
05-84-21
This bulletin announces availability of new front wheel hub assemblies incorporating bearing surfaces having increased resistance to imperfections resulting from shock loads.
11-199-20R
This bulletin announces availability of reprogramming files to optimize the Engine Control Module (ECM).
06-59-17R
This Service Information bulletin announces availability of a new front brake pad shim kit to specifically address customer concerns of a squeaking or squealing sound on the models listed above.
14-22-16R
To help reduce confusion and increase technician efficiency, Subaru of America, Inc. (SOA) has developed the following cross reference list to help locate the appropriate Special Service Tool.
15-267-20R
This bulletin provides information related to the telematics system's Automatic Collision Notification (ACN) and Advanced Automatic Collision Notification (AACN) feature operation, diagnostic tips, and best practices.
03-78-17R
This bulletin announces a design change to the clutch release bearing.
15-205-16R
This bulletin announces new reprogramming file availability and the software installation procedure to address additional operational concerns received from the field and listed involving âGen 2â F10 Navigation and Display Audio units with 7â display.
05-79-20
This Service Information Bulletin announces a change made to the wheel lug nuts.
12-305-20
This bulletin announces a design change made to the front hood air intake duct.
12-306-20R
This bulletin provides a repair procedure to address a squeaking sound coming from the backrest hinge area of the front seats. The procedure applies to both manually and power operated seat assemblies.
16-131-20
This Service Information Bulletin provides corrected diagnostics containing a revised flow for certain CVT solenoid related DTCs.
03-86-20
This bulletin provides additional repair procedures to follow when replacing a leaking clutch master cylinder on certain vehicles.
10-19-20
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
12-301-20
This bulletin outlines changes made to the rear shelf trim to address customer concerns of a rattling sound heard while driving over bumpy / rough roads.
06-77-20R
This bulletin announces the availability of reprogramming files to optimize the control module for the Vehicle Dynamics Control system (VDCCM). DTCs C1531 and/or C1741 may set, the Hill Holder warning lamp and cancellation alarm may activate and/or the VDC warning lamp can illuminate.
18-201-20
The purpose of this bulletin is to provide a desription of current changes to service manuals available via the Subaru Technical Information System (STIS) web site.
18-200-20
This bulletin provides a description of current changes to Service Manuals.
06-79-20
This bulletin announces availability of new master cylinder application shaft seals.
15-271-20
This service information bulletin announces discontinuation of both the "Stitcher" app and the related News Radio feature from the STARLINK app lineup effective 12 midnight on Thursday, September 24, 2020.
03-82-18R
This service information bulletin announces a design change to the clutch release bearing used on the models listed.
15-266-20
This Service Information Bulletin provides helpful procedures and best practices to utilize when customers present with concerns relating to the operation of their Gen 2 Telematics system equipped Subaru.
15-267-20
This document discusses some of the conditions that may trigger an Automatic Collision Notification (CAN) (Gen1) or Advanced Automatic Collision Notification (AACN) (Gen2), without a collision, airbag deployment, or accident taking place.
06-76-20
This service Information bulletin provides precautions to follow when servicing the Brembo brake calipers utilized on the models listed. Because of their aluminum construction, it is critcal to take extra care when servicing.
12-290-20
This Bulletin announces a design change made to the front seat backrest cover trim material on the models listed. The new material has enhanced wear resistance, especially in the side bolster area which may show wear over time from getting in and out of the seat.
12-288-20
This bulletin announces a design change made to the Slide Rail components of the left and right front power seat frame / track assemblies used on the models listed.
01-181-20
All Models (Vehicle Cleaning- COVID-19Best Practices)
07-174-20
This service bulletin provides details of a correction to the diagnostic procedure for DTC B2350- REAR RADAR COMMUNICATION ERROR on the models listed.
WUK-96R
Subaru of America, Inc. (Subaru) is initiating a service campaign for certain 2015-2018 Forester 2.0L Turbo and 2016-2018 WRX models which may experience a loosening of the front exhaust pipe nuts.
12-284-20
This bulletin announces availability of new interior door handles which will address isolated concerns of the chrome finish peeling.
17-17-13R
This bulletin provides information regarding Event Data Recorder (EDR) functionality which has been incorporated into the airbag system.
07-75-13R
This Bulletin provides information regarding DTC P0606 related specifically to the determination of this code on Forester Turbo and applicable WRX models.
03-83-20R
This bulletin announces availability of new shift forks and the corresponding sleeve and hub assembly to address isolated customer concerns of a rattling / vibration -type sound from the shift knob. The sound is primarily reported while driving in 4th gear between 1900 and 2500 rpm.
07-169-20
This Service Information bulletin describes a change made to the labels applied to the push to start switches used on the models listed.
15-199-16R
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field and listed below involving the Clarion Display Audio unit with 6.2" display.
15-204-16R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
11-199-20
This bulletin announces availability of reprogramming files to optimize the Engine Control Module (ECM). The new logic will address isolated concerns of a hard start condition occurring in cold weather (+10 degrees Fahrenheit or lower) and / or high-altitude areas. When this scenario occurs, the A/F learning control values move toward lean.
Subarunet Annou
Owner notification WUK-96 DIT exhaust pipe front (EPF) nut torque service campaign/voluntary emission recall.
07-152-19R
This bulletin announces availability of new power window switch assemblies.
07-167-20
This bulletin announces availability of a new stop lamp switch for the models listed above equipped with LED - type rear combination lamps.
11-195-20
This bulletin announces availability of a new vacuum hose assembly for the positive crankcase ventilation (PCV) system incorporating improved sealing to prevent potential oil seepage.
10-96-19
This bulletin announces availability of a new HVAC blower motor unit assemblies developed to address isolated concerns of the blower motor becoming inoperative. If this issues occurs on models with Auto A/C, the blower fan may become totally inoperative. If this issue occurs on models with Manual A/C, the blower fan may operate on high speed only. The root cause of these conditions is water intrusion into the blower motor causing rust and corrosion to develop. Over time, the blower motor may begin to draw more electrical current to operate. if that occurs, the additional draw can cause the related fuse and/ or blower resistor to fail. To address this condition, additional packing has been added to improve sealing of the blower unit case along with development of a new style cabin air filter which also in corporates improved sealing.
12/275/19
This bulletin announces a change made to the leather front seat cushion covers to address isolated concerns of a sagging/loose fitting condition after an occupant leaves the seat as shown in the example photos below. A pattern revision was made to increase tension of the cover material and decrease the time it takes for the condition to disappear after an occupant leaves the seat.
Subaru Announ
Subaru of America, Inc. (Subaru) is initiating a service campaign/ voluntary emissions recall for certain 2015-2018 Forester 2.0L Turbo and 2016-2018 WRX models which may experience a loosening of the fornt exhaust pip nuts.
WUK-96
Subaru of America, Inc. (Subaru) is initiating a service campaign for certain 2015-2018 Forester 2.0L Turbo and 2016-2018 WRX models which may experience a loosening of the front exhaust pipe nuts. On certain affected vehicles, the six (6) front exhaust pipe (EPF) nuts at the cylinder heads may not have been tightened sufficiently due to variations in production. As a result, these nuts may become loose during use and cause exhaust leakage. A leak occurring at the front exhaust pipe may result in deterioration of emission performance. As a result, affected vehicle may fail to meet emission levels certified by the EPA and/or California ARB.
07-146-19R
This bulletin announces a design change made to the engine wiring harness to improve resistance to moisture. A detailed illustration describing the change is supplied below.
07-161-19
This Service Information Bulletin announces a design change made to the side curtain and knee airbag modules on the models listed above to optimize commonization with the Japanese production parts. The change involves the mixture ratio of Argon to Helium used in the inflator gas: ⢠OLD gas ratio: 94% Argon, 6% Helium ⢠NEW gas ratio: 96% Argon, 4% Helium. All other specifications of these modules are unchanged.
15-253-19
This Service Information Bulletin provides the answer to potential inquiries regarding the STARLINK app being unable to play music files stored on a customerâs Android® phone / device through the head units (H/U) used in the applicable models listed above. This information is applicable ONLY to Android devices operating with Operating System (OS) version 10. IOS (AppleTM) devices are not affected.
12-271-19
This Service Information Bulletin announces a design change made to the rear bumper cover side mounting brackets. These new brackets provide increased clearance between the edges of the bumper cover and the corresponding quarter panels. This change will prevent them from contacting each other and possibly damaging their painted surfaces.
11-191-19R
This bulletin announces availability of a new Engine Control Module (ECM) for the models listed above designed to address DTC P2610: âECM/PCM ENGINE OFF TIMER PERFORMANCEâ. Under certain RARE conditions, an electrostatic surge may influence the ECMâs internal timer used after the engine is turned off and store a DTC P2610 in memory. Hardware in the ECM has been changed to eliminate any impact from electrostatic surges.
11-191-19
This bulletin announces availability of a new Engine Control Module (ECM) for the models listed above designed to address DTC P2610: âECM/PCM ENGINE OFF TIMER PERFORMANCEâ. Under certain RARE conditions, an electrostatic surge may influence the ECMâs internal timer used after the engine is turned off and store a DTC P2610 in memory. Hardware in the ECM has been changed to eliminate any impact from electrostatic surges.
06-65-18R
This bulletin announces a new Vehicle Dynamics Control (VDC) Module and Hydraulic Control Unit (VDCCM&HCU). The new part was designed to address a small number of customer concerns regarding a clicking or ticking-type sound heard coming from the driverâs side footrest area. The new modules incorporate logic with enhanced internal solenoid and motor control characteristics.
06-68-19R
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. This will prevent the pad from dragging due to corrosion buildup which may result in uneven or premature wear of the replacement brake pads. This additional instruction applies to all models with brake pads using the upper and lower pad clips and has been added to the brake pad installation procedures found in the related Service Manuals.
02-163-16R
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. The applicable Service Manuals will be revised with this new information in the near future.
02-182-19
This Service Information bulletin announces a design change made to the TGV assemblies used on the Forester Turbo models and WRXs listed above. Condensation resulting from EGR system operation may enter the area between the TGV shaft and bearing. Over time, corrosion can develop and impede movement of the TGV shaft and cause any of the DTCs P2004, 2005, 2006 and /or P2007 to set. The material of the TGV shaft has been changed to stainless steel to optimize corrosion resistance.
12-264-19
This Service Information bulletin announces a design change made to the retaining bolt used to secure the child anchors to the rear shelf plates on the models listed above. This change was made in support of parts communization with other similar mounting bolts. There is no change between the old and new bolt in terms of function or durability.
04-17-17-R
This bulletin provides a service procedure to address isolated customer concerns of a rattling sound identified as coming from the Electronic Power Steering (EPS) gear box (steering rack) assembly. The repair (when applicable) involves installation of a new tension spring for the worm gear to reduce / eliminate the condition.
07-152-19
This bulletin announces availability of new power window switch assemblies developed to address the following customer concerns: ? Power windows inoperative from the driver?s door master and / or passenger front door switch ? Unable to remotely operate other door windows from the driver?s door master switch ? One-Touch Auto Up / Down features inoperative from either / both front door switches
02-170-17R
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. The new seal will eliminate potential oil seepage into the wire harness connector portion of the valve. If oil seeps into the connector, over time, the Check Engine lamp may illuminate and set various AVCS-related DTCs.
07-150-19
This bulletin provides a procedure for replacing the rear combination lamp wiring harness. The harness is now available as a service part separate from the lamp assembly.
16-120-19
This bulletin provides a procedure to follow for addressing customer concerns of a shuddering condition or chattering -type sound heard or felt when making sharp turns. If an applicable vehicle presents with the condition as described, it is recommended to perform the transfer clutch break-in procedure as described.
02-178-18R
This Service Information bulletin announces a design change made to the rubber timing hole access plug to improve its retention and prevent water intrusion into the converter case.
16-119-19
This Service Information bulletin announces availability of a new control valve assembly (valve body) designed to prevent false detection of DTC P0841 and / or illumination of the AT Temp light. Testing has revealed in some limited cases, air bubbles (aerated fluid) may enter certain pressure circuits within the control valve assembly causing fluid pressure control and adjustment to be calculated incorrectly resulting in DTC P0841. The shape of these circuits has been changed to prevent this occurrence.
06-68-19
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. This will prevent the pad from dragging due to corrosion buildup which may result in uneven or premature wear of the replacement brake pads. This additional instruction applies to all models with brake pads using the upper and lower pad clips and has been added to the brake pad installation procedures found in the related Service Manuals.
07-146-19
This bulletin announces a design change made to the engine wiring harness to improve resistance to moisture. A detailed illustration describing the change is supplied below.
07-133-18
This Service Information Bulletin announces design changes to the engine?s knock sensor which will help improve vehicle assembly line efficiency and increase durability. In some cases, the Check Engine light may illuminate and a knock sensor-related DTC set in the ECM memory: P0327, P0328, P0332 and P0333. The knock sensor for DIT engines is now utilized for NA engines to improve durability and resistance to heat.
03-82-18
This Service Information bulletin announces a design change to the clutch release bearing used on the models as listed above. During assembly of the bearing, a different type of grease is used which has a higher resistance to heat. In cases where the operator keeps a foot on the clutch pedal for extended periods, an increased amount of heat is generated which can cause the grease inside the bearing to deteriorate. In a case of prolonged clutch pedal application, seizure of the bearing can occur with potential damage to other related components.
03-79-18R
This bulletin announces a change to the clutch system components optimizing their durability and resistance to certain severe driving conditions including high-temperature operation.
06-66-18
This Service Information bulletin announces a design change made to the front brake rotors used on the models listed above. The change makes it easier to identify these parts from those used on other models.
12-251-18
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully.There is a latch to keep the glove box closed on both sides of the glove box door. If the door is closed without using enough force to engage both latches or by pushing it shut on just one side instead of in the middle, one may close and not the other. Over time, if the door is not fully closed with both latches, high cabin temperatures along with weight of the items inside the glove box may cause the assembly to deform slightly and a gap to develop.
06-65-18
This bulletin announces a new Vehicle Dynamics Control (VDC) Module and Hydraulic Control Unit (VDCCM&HCU). The new part was designed to address a small number of customer concerns regarding a clicking or ticking-type sound heard coming from the driver?s side footrest area. The new modules incorporate logic with enhanced internal solenoid and motor control characteristics.
16-116-18
This Service Information bulletin provides details about revised CVT select lever (shifter) components. The shape of the lock plate and output of the shift lock solenoid have been changed.
07-128-18R
This Service Information bulletin provides a measurement and adjustment procedure for the stop lamp switch. An improperly adjusted (or faulty) stop lamp switch can cause any of the DTCs listed above to set and result in the related system?s warning lamp to illuminate.
16-115-18
In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Powertrain Warranty coverage for the Continuously Variable Transmission (CVT) on the above listed models and model years from the original five (5) years or sixty thousand (60,000) miles (whichever comes first) to ten (10) years or one-hundred thousand (100,000) miles (whichever comes first). This change is not in response to any specific condition, rather it is to provide customers with added assurance regarding the function and overall performance of their CVT. Additionally, vehicles which are beyond one-hundred thousand (100,000) miles at the time customer notification letters are mailed are being offered additional coverage for a period of one-year from the date of the customer notification letters.
02-178-18
This Service Information bulletin announces a design change made to the rubber timing hole access plug to improve its retention and prevent water intrusion into the converter case.
15-232-18
This Service Information bulletin announces a change made to the lens portion of the fog light assembly. The new lens has optimized light distribution characteristics while remaining interchangeable with the original type.
07-139-18R
This bulletin outlines a design change made to the inner lens extension portion of the LED headlamp assembly. Under the right conditions, the shape of the lens for the actual head lamp light source can cause sunlight to be focused onto the extension portion of the lens resulting in deformation. A heatresistant shade has been added to protect the affected area.
12-234-18
This bulletin provides a repair procedure for replacing the foam cushion installed between the top front edge of the IP and the windshield glass. Use the supplied Service Procedure to address a customer concern involving the foam cushion becoming visible above the IP near the defroster vent outlets.
06-63-18R
This bulletin announces a design change to the EPB adapter cord harness connector. In some cases, the retaining tab of the connector may become damaged as a result of removal or installation for diagnosis and later and cause DTC C1956 or C1957 to set and the brake warning lamp to illuminate. The retaining tab portion of the connector has been changed to improve its durability and prevent recurrence of the DTC. If there is no prior history of disconnection and the connector lock tab is not damaged, check for another possible cause for these DTCs.
12-201-16R
IMPORTANT: This Service Bulletin has been as been replaced by TSB 12-243-18 dated 6/6/2018 entitled ?Paint Chipping between Hood Grille (Scoop) and Hood?. Please refer to this new bulletin for the latest information regarding this condition.
12-243-18
This bulletin replaces TSB 12-201-16R and provides a new repair procedure to address customer concerns of the hood scoop scrubbing the finish of the hood panel in the areas shown in the photo. Due to different expansion rates between the metal hood panel and the resin material used for the hood scoop, the edges of the scoop?s rear corners may come in contact with the hood panel and abrade the finish.
10-88-18
This bulletin announces a change made to the Automatic Climate Control Head Assembly. The change will address concerns where the temperature selected for cooling ?feels? warmer to the customer than the temperature displayed. The new programming will adjust the threshold for when cooling occurs to improve the air conditioning system?s cooling effect making it more closely match the customer?s selected temperature.
12-241-18
4 DOOR MODELS ONLY. This bulletin announces a change made to the trunk lid lock (latch) assembly. The purpose of this change is to improve parts integration (or ?commonality?) between models. This change is not intended to address any specific customer concern.
15-222-18
This bulletin announces a design change to the A/C Condenser receiver-dryer assembly. The change involves the addition of a rubber end cap and retaining clip onto the bottom of the receiver-dryer tank portion to prevent corrosion intrusion and enhance sealing.
12-238-18R
This bulletin announces a design change to the front door checkers used on the models listed. The new checker mechanism provides a more ?positive feel? of the detents or check positions as the front doors are opened and closed.
07-134-18
This Service Information bulletin provides a new troubleshooting chart to use when diagnosing a DTC B1760 related to the Occupant Detection System (ODS). Following these diagnostic steps will help avoid unnecessary ODS sensor / seat cushion assembly replacement
06-61-18
This bulletin announces availability of new VDC Control Module & Hydraulic Units (VDCCM&H/U) to address isolated customer concerns of the green Hill Holder light blinking and cancel warning alarm sounding during cranking / starting the engine
18-192-18
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes.
12-231-18R
This bulletin announces a design change to the air vent grille located in the lower portion of the trunk (or cargo) area. The shutters of the vent grille are designed to open briefly and relieve cabin pressure when the doors are shut with the windows fully closed. The vent grilles have rubber ?shutters? which occasionally, may catch on the frame (case) portion and not close properly allowing outside air / odor to enter the cabin.
02-173-18
2.0L Turbo Models only. This bulletin announces availability of a special turbocharger air intake duct designed to prevent EXTREMELY RARE occurrence of ice formation from condensation in the duct?s PCV system passages.
F10-Gen2-NAV-15-
TECHNICAL SUPPORT GUIDE FOR NAVIGATION AND AUDIO F10 GEN2 SYSTEMS.
12-231-18
( 2017-2018MY Impreza - 5 Dr Only)
15-215-18
Models with FujitsuTEN (F10) Gen 2.0 / 2.1 Navigation or Display Audio Head Units ONLY. This bulletin provides a repair procedure to address specific, confirmed customer concerns of: ? Audio output interruption every 2-3 seconds when listening to AM or FM radio broadcasts ? No audio output at all when attempting to listen to a HD Radio broadcast.
UPDATE - Removal
The corrected update files are now available for download from Subarunet. TSB 15-20516R has been revised with new file names where applicable and re-posted to STIS.
f10-audio-navi-d
Subject: Removal of Certain Fujitsu 10 Audio / Navigation Update Files from Subarunet The following update files have been temporarily removed from Subarunet due to potential quality concerns with the 2nd file used in those updates. Retailers are requested to take the following action: ? If any of the following Fujitsu 10 Audio / Navigation files have been downloaded and saved locally, please discontinue their use and delete them immediately
11-174-17R
This bulletin announces the availability of reprogramming files to optimize the ECM and address the following customer concerns: ? Check Engine light coming on (with DTC P05A0 stored in memory). ? Potential battery discharge (dead battery) after repeated periods of short-trip driving. ? A high (or ?hanging?) engine RPM after depressing the clutch pedal (Forester only).
04-17-17R
This bulletin provides a service procedure to address isolated customer concerns of a rattling sound identified as coming from the Electronic Power Steering (EPS) rack assembly. The repair involves installation of a new tension spring for the worm gear to reduce / eliminate the condition. It should be noted the condition is NOT detrimental to the operation of the EPS system.
02-170-17
This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. The new seal will eliminate potential oil seepage into the wire harness connector portion of the valve. If oil seeps into the connector, over time, the Check Engine lamp may illuminate and set various AVCS-related DTCs.
07-118-17R
Models with SRVD Only. This bulletin provides revised diagnostic and repair procedures to address DTC B2327 for the Subaru Rear Vehicle Detection (SRVD), Blind-Spot Detection (BSD) and Rear Cross Traffic Alert (RCTA) system on the applicable models listed above. Under very specific (rare) conditions, the radar function of the SRVD system may experience a communication error and cause the SRVD warning lamp to illuminate. In addition, under certain highway driving conditions, an improper signal calculation by the system may cause a Cancel Code B2328 to set which will also cause the SRVD warning lamp to illuminate.
02-168-17
This Service Information bulletin announces a material change to the engine accessory drive / v-belt made to address customer concerns of a slipping belt (squeal or chirping) sound.
15-196-16R
ONLY 2016-2017MY: Those Models equipped with STARLINK Telematics. Provisioning is the process by which the DCM receives the subscription request and activates the related DCM features requested as outlined in the specific subscription contract. If provisioning is not successful then the DCM may remain in an inactive state and the requested services may not be activated for the customer. Field investigation has found that this may be a result of three possible conditions. * The DCM may be off the network due to vehicle storage or other network factors. * The DCM may be lacking power or ground due to some body side electrical concern. * The DCM may have an internal failure.
1117117
This bulletin announces the availability of reprogramming files to optimize the ECM and address isolated customer concerns of a spark knock (engine ping) -type sound.
096516R
REVISED. This bulletin announces a design change of the fuel injector used on 2.0L DIT models to prevent water intrusion. A new silicone rubber cover has been developed and incorporated into production for this purpose.
09-65-16
This bulletin announces a design change of the fuel injector used on 2.0L DIT models to prevent water intrusion. A new silicone rubber cover has been developed and incorporated into production for this purpose.
09-64-16
This Service Information bulletin announces a change to the shape of the rubber cap used on the flange nuts securing the sub-level sending unit to the fuel tank. In addition, two of the caps are now used in production instead of only one. This change was made to enhance productivity during vehicle assembly.
16-103-16
Only Models Equipped with TR690 CVT only. This bulletin has been developed in response to a small number of customer concerns regarding fluid seepage found coming from the CVT assembly. Investigation has identified a likely source of the seepage to be the sealant used on the CVT's oil pump chain cover. The repair involves removal, a thorough cleaning and inspection of the sealing surfaces followed by re-sealing the cover.
15-205-16
This bulletin announces new reprogramming file availability and the software installation procedure to address additional operational concerns received from the field and listed below involving ?Gen 2? F10 Navigation and Display Audio units with 7? display. The procedure will involve downloading the applicable software update files from Subarunet then loading them onto a flash drive for audio unit installation. It is important to read through and understand this information completely before proceeding. These latest software updates contain new logic to address the following concerns: ? Mirrorlink 1.1 updates ? Enable Mute function for Navigation guidance ? Incomplete display of intersection names in combination meter ? Increased accuracy of the XM Traffic information displayed ? Intermittent delay (approximately 1 minute) in display of map information after initial start-up of Navigation function (2015MY Legacy and Outback only).
12-209-16
This bulletin announces a design change to the front speaker grille. The new grilles have increased retention capabilities to address customer concerns of a loose fit.
12-189-15R
This bulletin provides information about changes made to the rear shelf trim to address customer concerns of a rattling sound heard while driving over bumpy / rough roads. The sources of the rattle have been identified as: ? the mounting points for the center stop lamp where it fits into the package shelf ? the package shelf itself rattling against the inside of the rear glass ? the rib and/or stand portions located on the underside of the package shelf contacting the shelf portion of the vehicle body.
12-207-16
This bulletin announces a change to the procedure used in production of the rear door glass assembly. The bottom edge of the door glass is pressed into a metal channel lined with rubber. The channel attaches the door glass assembly to the window regulator. In below-freezing temperature conditions, water freezing in the channel combined with the door glass sticking to the door weatherstrip can increase chance of the glass separating from the channel when attempting to operate (lower) the window. A lubricant has been added to the rubber portion to insure the glass gets fully seated during assembly which maximizes the clamping force of the channel on the glass.
078815R
This Service Information bulletin provides a procedure to use when installing a SOA821B200 replacement battery in a 2015MY WRX (2.0L). The sensor located on the battery ground terminal interferes with the battery vent cap used on the replacement battery.
139916R
Various paint manufacturers designate their own stock numbers and coding information although many of the major suppliers are now using the SOA paint codes to help eliminate possible confusion. Their color formulations are updated on a continual basis. Some vendors may have different color names than those provided to them by SOA. Be sure to double-check the codes and formulas beforehand to help insure an accurate color match. Should discrepancies arise, please refer your Body Shop contact inquiries to the specific paint vendor or their jobber/supplier for the most updated formula information.
1818816
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes. We advise you to always refer to the STIS web site when looking for the latest Service information. Printed pages will not be made available to update printed Service Manuals.
216316
This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. The applicable Service Manuals will be revised with this new information in the near future.
07-111-16
This bulletin announces a design change to the headlamp assembly to improve sealing and prevent moisture intrusion. This condition may result from a slight misalignment of the attaching points during the headlamp assembly process. An improved sealing material is now being used for bonding the outer lens to the housing.
15-199-16
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field and listed below involving the Clarion Display Audio unit with 6.2? display. The procedure will involve downloading the applicable software update files from Subarunet then loading them onto a flash drive for audio unit installation.
15-198-16
This bulletin announces reprogramming file availability and the software installation procedure to address a group of operational concerns received from the field listed below involving ?Gen 2? F10 Navigation and Display Audio units with 7? display. The procedure will involve downloading the applicable software update files from Subarunet then loading them onto a flash drive for audio unit installation. It is important to read through and understand this information completely before proceeding.
Announcement
New Vehicle Receipt- Navigation SD Card Transit Storage Location Change
0116809R
Replacement Key and Immobilizer Info
171713R
Event Data Recorder (EDR) Function of Airbag Module
Announcements-2
Effective with all 2015 model year cars and forward, the oil change interval is changing to 6,000 miles or 6 months, whichever comes first.
0214013
Oil Filler Cap Gasket Coming Unseated
WQE41-1
Puddle Light Recall
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.