Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
T-SB-0055-24 Rev2
Service Bulletin/Repair Instructions
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0035-24 Rev2
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev2
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev2
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev2
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.
T-SB-0062-23 Rev2
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
T-SB-0055-24 Rev1
Service Bulletin/Repair Instructions
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
T-SB-0035-24 Rev1
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev1
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev1
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0055-24
Service Bulletin/Repair Instructions
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0103-20 Rev1
Service Bulletin/Repair Instructions
This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 – 2025 model year Toyota vehicles.
T-SB-0061-23 Rev1
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
T-SB-0062-23 Rev1
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
T-SB-0035-24
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. •The entire bulletin has been updated.
T-SB-0039-24
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-PANT-2024-004-
Service Bulletin/Repair Instructions
This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
T-SB-0043-14
Service Bulletin/Repair Instructions
OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
TSB003220
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0057-18
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
Z2G_Dealer_Lette
Service Bulletin/Repair Instructions
DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
Z3G_Dealer_Lette
Service Bulletin/Repair Instructions
DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKG_Dealer_Lette
Service Bulletin/Repair Instructions
DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
T-SB-0094-21 Rev
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
Z3G_Paint_Repair
Service Bulletin/Repair Instructions
CSP: Customer Support Program ZKG ? Paint Repair Process
Z3G_Technical_In
Service Bulletin/Repair Instructions
TI: TECHNICAL INSTRUCTIONS Customer Support Program ZKG Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
TSB001221Rev2
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
TSB009421Rev1
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
Support Program
Service Bulletin/Repair Instructions
DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
ZKG_Paint_Repair
Service Bulletin/Repair Instructions
CSP: Customer Support Program ZKG - Paint Repair Process Operation Flow Chart
ZKG_Technical_In
Service Bulletin/Repair Instructions
TI: Technical Instructions Customer Support Program ZKG Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
TTT063620
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
T-SB-0014-22
Service Bulletin/Repair Instructions
TSB: This Service Bulletin includes procedures to replace damaged or loose front carpet floor retainer(s) without replacing the carpet assembly. Follow the Repair Procedure in this bulletin to replace the loose or damaged carpet floor retainer(s).
T-SB-0012-21 Rev
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
T-SB-0094-21
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
ZKG Important Up
Service Bulletin/Repair Instructions
DL: CUSTOMER SUPPORT PROGRAM ZKG Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
ZKG Customer Sup
Service Bulletin/Repair Instructions
RL: CUSTOMER SUPPORT PROGRAM ZKG Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
T-TT-0578-19 Rev
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ?Difficulty to pair the phone. ?Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
T-SB-0080-19 Rev
Service Bulletin/Repair Instructions
TSB: Some 2006 ? 2022 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
T-SB-0044-16 Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE March 08, 2021: This bulletin is now obsolete. Please see T-SB-0012-21.
Toyota Safety Re
Service Bulletin/Repair Instructions
Toyota Safety Recall and Service Campaign - Technician Certification Requirements
T-TT-0636-20 Rev
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-SB-0040-08 Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE March 08, 2021: This bulletin is now obsolete. Please see T-SB-0044-16.
T-SB-0012-21
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2021 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.
ZE6-DLP 129-14-2
Service Bulletin/Repair Instructions
Warranty enhancement program.
T-SB-0032-20 Rev
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-TT-0636-20
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
Customer Support
Service Bulletin/Repair Instructions
RE: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
T-TT-0628-20
Service Bulletin/Repair Instructions
TT: HVAC drain tube is found to be blocked/clogged.
T-SB-0062-20 Rev
Service Bulletin/Repair Instructions
TSB: Some 2004 ? 2020 model year Hybrid vehicles may exhibit an excessive buildup of dust, lint, or debris in the HV battery intake filter or cooling fan. The condition could reduce the efficiency of the HV battery cooling system. Perform the procedures outlined in this bulletin to address this condition.
ZKG_Proper_Photo
Service Bulletin/Repair Instructions
ZKG WEBSITE PROPER PHOTOGRAPH SUBMISSION
T-TT-0468-17 Rev
Service Bulletin/Repair Instructions
TT: HVAC drain tube is found to be blocked/clogged.
T-SB-0063-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. ST005-01, SU001-08, and T-SB-0391-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Toyota vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.
T-SB-0391-08 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE June 23, 2020: This bulletin is now obsolete. Please see T-SB-0063-20.
T-SB-0062-20
Service Bulletin/Repair Instructions
TSB: Some 2004 ? 2020 model year Hybrid vehicles may exhibit an excessive buildup of dust, lint, or debris in the HV battery intake filter or cooling fan. The condition could reduce the efficiency of the HV battery cooling system. Perform the procedures outlined in this bulletin to address this condition.
T-SB-0119-15_Rev
Service Bulletin/Repair Instructions
TT: This bulletin includes basic procedures for performing a rescue charge on Ni-MH high voltage (HV) batteries. This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing a rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger.
T-SB-0304-17 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE April 07, 2020: This bulletin is now obsolete. Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates
T-SB-0032-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0142-13_Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE February 12, 2020: This bulletin is now obsolete. Please see T-SB-0010-20.
T-SB-0010-20
Service Bulletin/Repair Instructions
TSB: Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced
ZKG_Dealer Email
Service Bulletin/Repair Instructions
Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
ZKG_Technical In
Service Bulletin/Repair Instructions
TECHNICAL INSTRUCTIONS Customer Support Program ZKG Phase 2 ? Customer Renotification and Repair Phase Repair is Now Available Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
T-SB-0008-20
Service Bulletin/Repair Instructions
TSB: Vehicles may display evidence of a fluid leak or fluid seep from powertrain components. This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.
ZKG_Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: December 12, 2019 This document has been updated to clarify that only authorized Toyota dealerships are authorized to confirm if the paint peeling condition is covered by this program. However, after confirming that the paint peeling condition is covered by this program, the authorized Toyota dealership may choose to coordinate to have the repainting repair performed by a non-Toyota repair facility (e.g. third-party collision repair facility, body shop, etc.).
T-SB-0162-19
Service Bulletin/Repair Instructions
TSB: Some 2008 ? 2019 model year Toyota vehicles painted with either 070 Blizzard Pearl or 040 Super White may exhibit peeling paint on one or more metal body panels. The paint may peel between the primer and E-coat layer, exposing the gray or brownish-green E-coat. The affected panel(s) will require prepping and repainting to address this condition. The paint repair may need to be sublet to a body shop.
ZKG_Paint Repair
Service Bulletin/Repair Instructions
Repair Process: Customer Support Program ZKG ? Paint Repair Process.
ZKG_Region Email
Service Bulletin/Repair Instructions
Region Email: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKG_Region Lette
Service Bulletin/Repair Instructions
Region Letter: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
T-TT-0578-19
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ? Difficulty to pair the phone. ? Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
T-SB-0033-14-Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE July 9, 2019: This bulletin is now obsolete. Please see T-SB-0080-19.
T-SB-0080-19
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0033-14. ? Applicability has been updated to include 2019 model year Toyota vehicles. Service Bulletin No. T-SB-0033-14 is obsolete and any printed versions should be discarded. Some 2006 ? 2019 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part. NOTE The ARINIX® Tip is NOT registered or labeled for sale or use outside the United States or Puerto Rico.
T-SB-0076-19
Service Bulletin/Repair Instructions
TSB: Some 2009 ? 2019 model year Toyota vehicles with super chrome wheel finishes may become discolored and/or damaged when aftermarket cleaners, polishes, or brake dust removal products are used on wheels with super chrome finishes. Wheel cleaners and polish that contain acidic substances may damage the clear coat of the wheel, resulting in the undercoating (black) to become visible.
T-SB-0134-16-Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 01, 2019 Rev2: ? Applicability has been updated to 2019 ? 2020 model year Toyota vehicles. ? The Techstream Preparation and Process Overview sections have been updated. October 30, 2017 Rev1: ? Applicability has been updated to include 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit
T-TT-0414-16-Rev
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ? Difficulty to pair the phone. ? Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
T-TT-0468-17-Rev
Service Bulletin/Repair Instructions
TT: HVAC drain tube is found to be blocked/clogged.
T-SB-0044-16_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE February 7, 2019 Rev2: * Applicability has been updated to include 2010 - 2014 model year Matrix, 2017 - 2019 model year C-HR, 2019 model year Corolla Hatchback, and 2018 - 2019 model year Toyota vehicles. G418 The Introduction and Repair Procedure sections have been updated. March 7, 2017 Rev1: * Applicability has been updated to include 2017 model year Toyota vehicles. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0040-08. * Applicability has been updated to include applicable 2016 model year vehicles. Service Bulletin No. T-SB-0040-08 is obsolete and any printed versions should be discarded. Some 2010 - 2019 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0151-18
Service Bulletin/Repair Instructions
TSB: Some 2009 ? 2012 model year RAV4 and 2010 ? 2011 model year Camry vehicles equipped with 2AR-FE (non-PZEV) engines may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P0138 (Oxygen Sensor Circuit High Voltage [Bank 1 Sensor 2]). This condition may be caused by incorrect air fuel ratio sensor response. The Engine Control Module/ECM (SAE Term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition occurring. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0033-14_Rev
Service Bulletin/Repair Instructions
TSB: Some vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
PG004-97-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
PG006-01-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
T-SB-0304-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 31, 2018 Rev2: ? The Supersession Notice has been updated. January 11, 2018 Rev1: ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.
ZJA-Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: June 22, 2018 A correction was made to the coverage parameters. ? The owner notification schedule was updated. ? A sample of the Owner Letter has been attached to the Dealer Letter. Toyota has received reports indicating that a combination of high humidity, high temperatures and light intensity may cause the surface of the Dashboard (Instrument Panel) in some of the subject vehicles to become cracked and/or sticky over time. The Dashboard (Instrument Panel) is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first). However, because we at Toyota care about each customer?s ownership experience, Toyota is now offering a voluntary Customer Support Program that applies to cracked and/or sticky Dashboards (Instrument Panels) of covered vehicles as a result of heat, humidity, and light intensity, regardless of whether the vehicle is out of warranty. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZJA-Toyota POL18
Service Bulletin/Repair Instructions
Warranty Policy Bulletin: Toyota has received reports indicating that a combination of high humidity, high temperatures, and light intensity, may cause the surface of the Dashboard (Instrument Panel) in some of the subject vehicles to become cracked and/or sticky over time.
ZG5_Toyota POL17
Service Bulletin/Repair Instructions
Warranty Policy Bulletin: Toyota has received reports of customer concerns in which the power moon roof, power sliding doors or power hatch are inoperative from the overhead console switches or require excessive pressure on the overhead console switches to operate. Due to parts availability this Warranty Enhancement Program will be launched in 2 phases as illustrated below: 1 Camry and Camry Hybrid Certain 2012 March, 2017 Repair, Available 2 Sienna Certain 2011-2013 June, 2017 Repair Available.
ZJA_Toyota POL18
Service Bulletin/Repair Instructions
Warranty Policy Bulletin: Toyota has received reports indicating that a combination of high humidity, high temperatures, and light intensity, may cause the surface of the Dashboard (Instrument Panel) in some of the subject vehicles to become cracked and/or sticky over time.
T-SB-0039-15_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE May 25, 2018 Rev1: * The Introduction, Production Change Information, and Repair Procedure sections have been updated. Any previous printed versions of this bulletin should be discarded. Some 2003 - 2011 model year Toyota vehicles may exhibit a condition where the instrument panel pad (dashboard) becomes cracked and/or sticky. Follow the procedure in this bulletin to address this condition.
ZJA_Dealer Daily
Service Bulletin/Repair Instructions
Dealer Daily Message: Customer Support Program ZJA. Certain 2010 - 2011 Model Year Camry Vehicles. Certain 2009 - 2011 Model Year Camry Hybrid Vehicles. Repair Coverage for the Dashboard (Instrument Panel). * Customer Support Program ZJA Dealer Letter is available on TIS. Refer to the Dealer Letter on TIS for additional information.
ZJA_Dealer Email
Service Bulletin/Repair Instructions
Dealer Email: Toyota has received reports indicating that a combination of high humidity, high temperatures and light intensity may cause the surface of the Dashboard (Instrument Panel) in some of the subject vehicles to become cracked and/or sticky over time. The Dashboard (Instrument Panel) is covered by Toyota's New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first). However, because we at Toyota care about each customer's ownership experience, Toyota is now offering a voluntary Customer Support Program that applies to cracked and/or sticky Dashboards (Instrument Panels) of covered vehicles as a result of heat, humidity, and light intensity, regardless of whether the vehicle is out of warranty.
ZJA_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: Toyota has received reports indicating that a combination of high humidity, high temperatures and light intensity may cause the surface of the Dashboard (Instrument Panel) in some of the subject vehicles to become cracked and/or sticky over time. The Dashboard (Instrument Panel) is covered by Toyota's New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first). However, because we at Toyota care about each customer's ownership experience, Toyota is now offering a voluntary Customer Support Program that applies to cracked and/or sticky Dashboards (Instrument Panels) of covered vehicles as a result of heat, humidity, and light intensity, regardless of whether the vehicle is out of warranty.
ZJA_J0B Aid_05.2
Service Bulletin/Repair Instructions
Job Aid: CUSTOMER SUPPORT PROGRAM ZJA Repair Coverage for the Dashboard (Instrument Panel) Inspection Application Navigation Instructions.
ZJA_Region Email
Service Bulletin/Repair Instructions
Region Email: Toyota has received reports indicating that a combination of high humidity, high temperatures and light intensity may cause the surface of the Dashboard (Instrument Panel) in some of the subject vehicles to become cracked and/or sticky over time. The Dashboard (Instrument Panel) is covered by Toyota's New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first). However, because we at Toyota care about each customer's ownership experience, Toyota is now offering a voluntary Customer Support Program that applies to cracked and/or sticky Dashboards (Instrument Panels) of covered vehicles as a result of heat, humidity, and light intensity, regardless of whether the vehicle is out of warranty.
ZJA_Region Lette
Service Bulletin/Repair Instructions
Region Letter: Toyota has received reports indicating that a combination of high humidity, high temperatures and light intensity may cause the surface of the Dashboard (Instrument Panel) in some of the subject vehicles to become cracked and/or sticky over time. The Dashboard (Instrument Panel) is covered by Toyota's New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first). However, because we at Toyota care about each customer's ownership experience, Toyota is now offering a voluntary Customer Support Program that applies to cracked and/or sticky Dashboards (Instrument Panels) of covered vehicles as a result of heat, humidity, and light intensity, regardless of whether the vehicle is out of warranty.
T-SB-0187-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE February 12, 2018 Rev2: ? Applicability has been updated to include 2015 ? 2018 model year vehicles. January 23, 2014 Rev1: ? Applicability has been updated to include 2013 ? 2014 model year vehicles. Any previous printed versions of this bulletin should be discarded. Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.
T-SB-0009-18
Service Bulletin/Repair Instructions
TSB: The purpose of this Service Bulletin is to elevate awareness and provide best practices for leather and synthetic leather care in Toyota vehicles. As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care.
T-SB-0229-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 22, 2017 Rev1: ? Applicability has been updated to include 2014 ? 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. In the event that a Toyota vehicle becomes submerged in water, many components may be physically damaged. Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.
ZE6-Toyota POL14
Service Bulletin/Repair Instructions
Warranty Policy Bulletin: Toyota has received reports where some vehicles may exhibit cracked and/or sticky/melting dashboards as a result of heat or humidity. In Mid-December, 2014, Toyota announced the reimbursement Phase of this voluntary warranty enhancement program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota has launched the part replacement portion of this Program in several phases.
ZE7-Toyota POL14
Service Bulletin/Repair Instructions
Warranty Policy Bulletin: Toyota has received some reports where vehicles may exhibit excessive engine oil consumption. Toyota is now announcing the part replacement phase of Warranty Enhancement Program ZE7 for vehicles exhibiting excessive engine oil consumption.
T-SB-0134-16_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE October 30, 2017 Rev1: * Applicability has been updated to include 2018 model year vehicles. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.
T-SB-0304-17
Service Bulletin/Repair Instructions
TSB: Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.
SET-TSB-16-001
Service Bulletin/Repair Instructions
Revised Document- Southeast Toyota Accessory Advent Navigation system displays splash screen only or randomly shuts off, Discusses audio system hard reset procedure and updated software card. Updated contact information for Radio software
T-SB-0218-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 20, 2017 Rev1: Applicability has been updated to exclude 2007 ? 2017 model year Avanza vehicles. Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities.
ZE6_Toyota POL14
Service Bulletin/Repair Instructions
Warranty Policy Bulletin POL14-11: Rev Toyota has received reports where some vehicles may exhibit cracked and/or sticky/melting dashboards as a result of heat or humidity.
T-TT-0432-17_Rev
Service Bulletin/Repair Instructions
TT: Rev2 Some Customers may complain about a Hybrid Vehicle Battery cooling system warning message. This warning message may appear when the HV Battery cooling system loses efficiency due to debris on the filter and or some object obstructing the air inlet. Refer to the information below to address this issue.
ZE6 Dealer Daily
Service Bulletin/Repair Instructions
Dealer Daily: Voluntary Extension of Warranty Coverage for Cracked and/or Sticky/Melting Dashboards (Instrument Panels) as a Result of Heat or Humidity.
ZE6_POL14-11_War
Service Bulletin/Repair Instructions
Warranty Policy Bulletin POL14-11: REVISED March 22, 2017: Toyota has received reports where some vehicles may exhibit cracked and/or sticky/melting dashboards as a result of heat or humidity.
T-TT-0365-15_Rev
Service Bulletin/Repair Instructions
TT: Rev2 A vehicle may arrive to the dealer with a MIL ?ON? condition and P0A80 or P1AC000 stored in the memory. Some cases have been identified with internal modification done to the HV Battery. Modified or altered parts are not covered under warranty.
T-TT-0435-17
Service Bulletin/Repair Instructions
TT: This bulletin is regarding best practices when handling navigation systems that use Hard Disc Drive or Micro SD Card memory.
T-TT-0365-15 Rev
Service Bulletin/Repair Instructions
TT: A vehicle may arrive to the dealer with a MIL ?ON? condition and P0A80 or P1AC000 stored in the memory. Some cases have been identified with internal modification done to the HV Battery. Modified or altered parts are not covered under warranty.
TTT043217 Rev1
Service Bulletin/Repair Instructions
TT: Some Customers may complain about a Hybrid Vehicle Battery cooling system warning message. This warning message may appear when the HV Battery cooling system loses efficiency due to debris on the filter and or some object obstructing the air inlet.
ZE7 Phase 2 POL1
Service Bulletin/Repair Instructions
Warranty Policy Bulletin: Toyota has received some reports where vehicles may exhibit excessive engine oil consumption. Toyota is now announcing the part replacement phase of Warranty Enhancement Program ZE7 for vehicles exhibiting excessive engine oil consumption.
TTT043217
Service Bulletin/Repair Instructions
TT: Some Customers may complain about a Hybrid Vehicle Battery cooling system warning message. This warning message may appear when the HV Battery cooling system loses efficiency due to debris on the filter and or some object obstructing the air inlet.
TSB018217
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-SB-0012-13 Rev
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE: September 14, 2016: This bulletin is now obsolete. Please see T-SB-0134-16.
T-SB-0142-13 Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 10, 2016 Rev2: ? Applicability has been updated to include 2016 ? 2017 model year Toyota vehicles. ? Parts Information section has been updated. Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.
T-TT-0365-15
Service Bulletin/Repair Instructions
TT: A vehicle may arrive to the dealer with a MIL ?ON? condition and P0A80 stored in the memory. Some cases have been identified with internal modification done to the HV Battery. Modified or altered parts are not covered under warranty.
T-SB-0137-16
Service Bulletin/Repair Instructions
TSB: Some 2007 ? 2014 model year North American produced Camry and Camry HV vehicles may exhibit a condition where the fuel lid door will not open when pulling up on the fuel lid lock lever. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0134-16
Service Bulletin/Repair Instructions
TSB: Supersession Notice. Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
T-TT-0414-16
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: *Difficulty to pair the phone. *Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. *Various Bluetooth® Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls.
Safety Recall an
Service Bulletin/Repair Instructions
Update on Technician Certification Requirements.
ZE6_WEP_Dealer L
Service Bulletin/Repair Instructions
DL: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program (the "Program"). This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003 - 2005 model year 4Runner, 2005 - 2010 model year Avalon, 2007 - 2011 model year Camry and Camry Hybrid, 2004 -2010 model year Sienna, and 2004 - 2008 model year Solara vehicles. In Mid-December, 2014 Toyota announced the reimbursement Phase of this Program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota will be launching the part replacement portion of this Program is several phases; please refer to the table below for part replacement model phasing.
T-SB-0032-14 OBS
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE: THIS BULLETIN IS NO LONGER APPLICABLE AND IS NOW OBSOLETE.
T-SB-0032-14 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE: This bulletin is no longer applicable and is now obsolete.
T-SB-0044-16
Service Bulletin/Repair Instructions
TSB: On some vehicles, when Rapgard? is removed, the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.
T-TT-0395-16
Service Bulletin/Repair Instructions
TT: HV Batteries have liquid filled cell modules, to prevent leakage from cells, it is very important to confirm the proper orientation mark of the DRC.
T-SB-0036-13 Rev
Service Bulletin/Repair Instructions
TSB: This bulletin includes basic procedures for inspecting and adjusting World Standard (WS) Automatic Transmission Fluid (ATF) level at normal vehicle operating temperature. Note: The following adjustment procedures are for U660E/F and U760E/F transmissions.
T-TT-0268-13 REV
Service Bulletin/Repair Instructions
TT: SOME CUSTOMERS MAY ENCOUNTER BLUETOOTH CONNECTIVITY CONCERNS SUCH AS: DIFFICULTY PAIRING THE PHONE. INTERMITTENT BLUETOOTH FAILURE TO CONNECT WHEN FIRST TURNING ON THE VEHICLE. VARIOUS BLUETOOTH AUDIO FUNCTIONS ARE NO LONGER FUNCTIONING WITH THE CUSTOMERS PHONE, SUCH AS THE ABILITY TO CHANGE THE TRACK USING THE STEERING WHEEL CONTROLS. THESE CONCERNS CAN BE CAUSED BY CHANGES MADE ON THE CUSTOMERS PHONE. MAKE SURE TO INQUIRE WITH THE CUSTOMER IF THE CONNECTIVITY CONCERNS OCCURRED AFTER RECEIVING AN OPERATING SYSTEM UPDATE ON THEIR PHONE OR IF THEY HAVE RESTORED THEIR PHONE DATA/SETTINGS RECENTLY.
TTT-0268-13 Rev3
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth connectivity concerns such as: ? Difficulty pairing the phone. ? Intermittent Bluetooth failure to connect when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with the customer?s phone, such as the ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.
SET-TSB-15-005
Service Bulletin/Repair Instructions
Discusses Southeast Toyota Accessory Keyless Entry system General trouble shooting and revised control module identification.
T-TT-0381-16
Service Bulletin/Repair Instructions
Tech Tip: Some customers may experience difficulty programming HomeLink.
T-TT-0372-15 Rev
Service Bulletin/Repair Instructions
TT: In certain cases, vehicles undergoing the ZE7 AZ Oil Consumption repair procedure will require a short block replacement. Currently, when a new short block assembly is ordered for a vehicle, dowels pins connecting the short block to the crankcase stiffener are not present.If you are performing a short block replacement under ZE7, please order the following parts in addition to the short block, and install in the new short block upon receipt.
POL14-11
Service Bulletin/Repair Instructions
WPB: TOYOTA HAS RECEIVED REPORTS WHERE SOME VEHICLES MAY EXHIBIT CRACKED AND/OR STICKY/MELTING DASHBOARDS AS A RESULT OF HEAT OR HUMIDITY. IN MID-DECEMBER, 2014, TOYOTA ANNOUNCED THE REIMBURSEMENT PHASE OF THIS WARRANTY ENHANCEMENT PROGRAM. SINCE PRIOR TO THAT ANNOUNCEMENT, TOYOTA HAS BEEN DILIGENTLY MAKING PARTS PREPARATIONS FOR THE PARTS REPLACEMENT PHASE OF THIS PROGRAM. DUE TO THE AGE, VOLUME, AND BREADTH OF THE COVERED VEHICLES SUBJECT TO THE PROGRAM AND THE SIZE AND COMPLEXITY OF DASHBOARD MANUFACTURING, TOYOTA HAS LAUNCHED THE PART REPLACEMENT PORTION OF THIS PROGRAM IN SEVERAL PHASES; PLEASE REFER TO THE TABLE BELOW FOR PART REPLACEMENT MODEL PHASING.
ZE6-Dealer Daily
Service Bulletin/Repair Instructions
DD: In Mid-December 2014, Toyota announced the reimbursement Phase of this Program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota has launched the part replacement portion of this Program in several phases; please refer to the table below for part replacement model phasing.
ZE6-Dealer Lette
Service Bulletin/Repair Instructions
DL: In our continuing efforts to ensure the best in customer satisfaction, Toyota has announced a Warranty Enhancement Program (the ?Program?). This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.
ZE6-WPB POL14-11
Service Bulletin/Repair Instructions
WPB: Toyota has received reports where some vehicles may exhibit cracked and/or sticky/melting dashboards as a result of heat or humidity. In Mid-December, 2014, Toyota announced the reimbursement Phase of this warranty enhancement program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota has launched the part replacement portion of this Program in several phases; please refer to the table below for part replacement model phasing.
ZE6_DEALER 12/3
Service Bulletin/Repair Instructions
DL: IN OUR CONTINUING EFFORTS TO ENSURE THE BEST IN CUSTOMER SATISFACTION, TOYOTA HAS ANNOUNCED A WARRANTY ENHANCEMENT PROGRAM (THE PROGRAM). THIS PROGRAM EXTENDS THE WARRANTY COVERAGE FOR REPAIRS RELATED TO CRACKED AND/OR STICKY/MELTING DASHBOARDS (INSTRUMENT PANELS) AS A RESULT OF HEAT OR HUMIDITY ON 2003-2005 MODEL YEAR 4RUNNER, 2005-2010 MODEL YEAR AVALON, 2007-2011 MODEL YEAR CAMRY AND CAMRY HYBRID, 2004-2010 MODEL YEAR SIENNA, AND 2004-2008 MODEL YEAR SOLARA VEHICLES.
ZE6_DEALERD 12/3
Service Bulletin/Repair Instructions
DD: IN MID-DECEMBER 2014, TOYOTA ANNOUNCED THE REIMBURSEMENT PHASE OF THIS PROGRAM. SINCE PRIOR TO THAT ANNOUNCEMENT, TOYOTA HAS BEEN DILIGENTLY MAKING PARTS PREPARATIONS FOR THE PARTS REPLACEMENT PHASE OF THIS PROGRAM. DUE TO THE AGE, VOLUME, AND BREADTH OF THE COVERED VEHICLES SUBJECT TO THE PROGRAM AND THE SIZE AND COMPLEXITY OF DASHBOARD MANUFACTURING, TOYOTA HAS LAUNCHED THE PART REPLACEMENT PORTION OF THIS PROGRAM IN SEVERAL PHASES; PLEASE REFER TO THE TABLE BELOW FOR PART REPLACEMENT MODEL PHASING.
T-SB-0119-15
Service Bulletin/Repair Instructions
TSB: This bulletin includes basic procedures for performing a Rescue Charge on Ni-MH High Voltage (HV) Batteries. This bulletin should be used in conjunction with the Repair Manual while performing Rescue Charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) Charger.
T-TT-0361-15 Rev
Service Bulletin/Repair Instructions
TT: Based on current part order allocation, some piston types have been incorrectly identified while undergoing the ZE7 2AZ Oil Consumption repair procedure. * Replacement pistons for ZE7 should be ordered based on the pistons removed from existing cylinder block and no longer by measurement. * This Tech Tip includes information regarding production allocation and instructions for identifying piston type on subject engines. This will be published in the next revision of T-SB-0030-15.
T-SB-0030-15
Service Bulletin/Repair Instructions
TSB: Some 2006 - 2013 model year vehicles equipped with the 2AZ engine may exhibit engine oil consumption. The piston assembly has been changed to minimize oil consumption. Use the following Repair Procedure to address this condition.
T-TT-0362-15
Service Bulletin/Repair Instructions
TT: The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
T-TT-0360-15
Service Bulletin/Repair Instructions
TT: Customers may experience connectivity issues when the following conditions are met: The customer's iPhone is operating on iOS9 firmware. The customer's iPhone is connected to the vehicle via Bluetooth. The customer may complain of the following issues: When receiving two incoming calls simultaneously, both calls are ended automatically. iTunes Radio app does not play via Bluetooth audio. Podcast and Audiobook media playback is inoperative via Bluetooth audio.
T-TT-0361-15
Service Bulletin/Repair Instructions
TT: BASED ON CURRENT PART ORDER ALLOCATION, SOME PISTON TYPES HAVE BEEN INCORRECTLY IDENTIFIED WHILE UNDERGOING THE ZE7 2AZ OIL CONSUMPTION REPAIR PROCEDURE. REPLACEMENT PISTONS FOR ZE7 SHOULD BE ORDERED BASED ON THE PISTONS REMOVED FROM THE EXISTING CYLINDER BLOCK AND NO LONGER BY THE MEASUREMENT. THIS TECH TIP INCLUDES INFORMATION REGARDING PRODUCTION ALLOCATION AND INSTRUCTIONS FOR IDENTIFYING PISTON TYPE ON SUBJECT ENGINES. THIS WILL BE PUBLISHED IN THE NEXT REVISION OF T-SB-0030-15
WPB (POL 14-11)_
Service Bulletin/Repair Instructions
WPB: Toyota has received reports where some vehicles may exhibit cracked and/or sticky/melting dashboards as a result of heat or humidity. In Mid-December, 2014 Toyota announced the reimbursement Phase of this warranty enhancement program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota will be launching the part replacement portion of this Program in several phases; please refer to the table below for part replacement model phasing. Although Toyota is increasing production levels, it is difficult to predict customer demand and where parts need to be shipped to support customer demand. It is important that dealerships explain to customers that there still may be a period of time the customer will need to wait before part replacement can be performed. Please be sure to take this into consideration when performing customer scheduling.
T-TT-0353-15
Service Bulletin/Repair Instructions
TechTip: Condition - There has been some concern with 3 Piece Piston Ring installations for 2AZ-FE and 2AZ-FXE engines. This TechTip contains the accepted installation method required for Toyota vehicles.
T-TT-0086-11
Service Bulletin/Repair Instructions
TechTip: Condition - The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
ZE6_Dealer Lette
Service Bulletin/Repair Instructions
DL: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program (the ?Program?). This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.
ZE6_Warranty Enh
Service Bulletin/Repair Instructions
RL: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program (the ?Program?). This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.
T-SB-0043-14 Rev
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.
ZE6_WPB POL14-11
Service Bulletin/Repair Instructions
WPB: Toyota has received reports where some vehicles may exhibit cracked and/or sticky/melting dashboards as a result of heat or humidity.
POL-14-11
Service Bulletin/Repair Instructions
TOYOTA: DURING THE HUMIDITY OR HEAT, THE DASHBOARD WOULD BE EITHER STICKY, MELTING, OR CRACKED AND A PART REPLACEMENT HAS PHASED INTO PROGRAM. MODELS 2003-05 4RUNNER, 2005-10 AVALON, 2007-11 CAMRY & HYBRID, 2004-10 SIENNA, 2004-08 SOLARA. *PE
T-SB-0039-15
Service Bulletin/Repair Instructions
TSB: Certain 2003 - 2011 model year Toyota vehicles may exhibit a condition where the instrument panel pad (dashboard) becomes cracked and/or has a shiny/degraded appearance. The pad surface may also become sticky or adherent. Follow the procedure in this bulletin to address this condition.
T-SB-0094-11 Rev
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE-May 26, 2015: This bulletin is now obsolete. Please see T-SB-0030-15.
T-SB-0083-13 Rev
Service Bulletin/Repair Instructions
TSB: The procedure in this bulletin is a general guideline on how to properly diagnose the air conditioning system after a component failure. Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.
T-TT-0337-15
Service Bulletin/Repair Instructions
TT: When updating either the navigation or radio firmware, verify the vehicle applicability BEFORE beginning the update.
T-SB-0158-14 Rev
Service Bulletin/Repair Instructions
TSB: Some 2006 - 2013 model year vehicles equipped with 2AZ-FE or 2AZ-FXE engines may exhibit engine oil consumption. The piston assembly has been changed to minimize oil consumption. Use the Inspection Procedure in this bulletin to confirm this condition.
T-TT-0234-13 Rev
Service Bulletin/Repair Instructions
TT: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems. Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.
T-SB-0101-11 Rev
Service Bulletin/Repair Instructions
TSB: When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-TT-0262-13 Rev
Service Bulletin/Repair Instructions
TT: Starting with 2010 Model Year, Toyota began a gradual transition to the use of synthetic 0w-20 viscosity engine oil. There are multiple benefits of this oil. Due to the them improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicles that require this oil.
TTT-0337-15 Rev1
Service Bulletin/Repair Instructions
TT: When updating either the navigation or radio firmware, verify the vehicle applicability BEFORE beginning the update.
T-TT-0268-13 Rev
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: * Difficulty to pair the phone. * Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. * Various Bluetooth® Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.
T-SB-0040-08
Service Bulletin/Repair Instructions
TSB: On some vehicles, when Rapgard is removed, the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.
ZE7_WEP_Updated_
Service Bulletin/Repair Instructions
EC: The Tamper Tape recommended for the 2AZ-FE Engine Oil Consumption Inspection Procedure found in T-SB-0158 (Toyota) and S-SB-0031-14 (Scion) is now available at the MDC. The bulletins will be updated to reflect the new ordering process and posted on TIS in the near future.
TT-0307-14 Rev2
Service Bulletin/Repair Instructions
TT: Some customers may encounter various Bluetooth connectivity concerns after upgrading to iOS 8.0 and later. Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.
T-SB-0012-13 REV
Service Bulletin/Repair Instructions
TSB: FLASH REPROGRAMMING ALLOWS THE ECU SOFTWARE TO BE UPDATED WITHOUT REPLACING THE ECU. FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION.
TSB-0012-13 Rev2
Service Bulletin/Repair Instructions
TSB: Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
T-TT-0321-15
Service Bulletin/Repair Instructions
TT: Customer complaint of MIL (:Check Engine Light) ON Condition. Health Check retrieves DTC P2118 (Throttle Actuator Motor Current Range/Performance).
T-TT-307-14 Rev1
Service Bulletin/Repair Instructions
TT: Customers complain of various Bluetooth connectivity concerns after upgrading to iOS 8.0 and later. Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.
T-SB-0158-14
Service Bulletin/Repair Instructions
TSB: Some 2006-2011 model year vehicles equipped with 2AZ-FE or 2AZ-FXE engines may exhibit engine oil consumption. The piston assembly has been changed to minimize oil consumption. Use the Inspection Procedure in this bulletin to confirm this condition.
ZE6-DLP 129-14
Service Bulletin/Repair Instructions
Warranty enhancement program.
ZE6_Electronic C
Service Bulletin/Repair Instructions
Electronic Communication: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program. This program extends the warranty coverage for repairs related to cracked and/or sticky/melted dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.
ZE6_Region Lette
Service Bulletin/Repair Instructions
Region Letter: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program. This program extends the warranty coverage for repairs related to cracked and/or sticky/melted dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.
T-SB-0150-14
Service Bulletin/Repair Instructions
TSB: The purpose of this general information Service Bulletin is to announce sub-component diagnosis and replacement is now available for the Hybrid Transaxle assembly equipped on 2007 - 2011 model year Camry HV, 2006 - 2015 model year Highlander HV, 2010 - 2015 model year Prius, and 2012 - 2015 model year Prius PHV and Prius V vehicles.
11-12-2014
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0006-11 Rev
Service Bulletin/Repair Instructions
TSB: World Standard (WS) Automatic Transmission Fluid (ATF) was introduced to reduce maintenance costs and increase the mileage between scheduled maintenance checks. Here are some important tips when working with ATF-WS in Toyota vehicles requiring it's use.
T-SB-0014-11 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this service bulletin is to provide information regarding the installation of the correct torque converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing washers can cause damage to the torque converter assembly.
T-SB-0260-08 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to assist in the identification and location of serial numbers on 2006 -2014 model year remanufactured automatic transmissions.
T-TT-0307-14
Service Bulletin/Repair Instructions
Tech Tip: Customer complains of carious Bluetooth connectivity concerns after upgrading to iOS 8.0 and later. Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.
T-SB-0134-14
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL "ON" shifting issues and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly.
T-SB-0200-08 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to assist in the identification and location of serial numbers on 2006 - 2014 model year automatic transmissions.
T-SB-0041-14 Rev
Service Bulletin/Repair Instructions
TSB: Some 2007 - 2011 model year Camry HV vehicles may exhibit a condition where the brake, ABS, and/or TRAC warning light(s) are ON and/or a Check VSC message is displayed. Diagnostic Trouble Code (DTC) C1391, C1252, C1253 or C1256 may be stored. This condition may be caused by a small internal brake fluid leak inside the brake actuator.
T-TT-0234-13
Service Bulletin/Repair Instructions
Tech Tip: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems.
T-SB-0351-10
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0351-10 Rev
Service Bulletin/Repair Instructions
TSB: This bulletin supplements the Repair Manual procedures for transaxle removal and replacement, with details on the use of a new Engine Support Bar (ESB), SST P/N 00002-ESUPPT-01, to assist in the removal and installation of the transaxle assembly. With the use of the Engine Support Bar, it is no longer required for the engine assembly to be removed from the vehicle when removing and installing the transaxle assembly.
T-TT-0246-13 Rev
Service Bulletin/Repair Instructions
Tech Tip: Tips for writing a DPR (Dealer Product Report) on manufacturing issues for windows and windshields.
E0U_LSC_Dealer L
Service Bulletin/Repair Instructions
Dealer Letter: The subject vehicles contain a brake reservoir which has two separate chambers connected by a filter. This filter may become clogged, resulting in illumination of the Brake ( ) warning lamp due to low fluid level in one of the reservoir chambers. Under certain conditions this could cause additional warning lamps shown below to illuminate and front brake assist could be temporarily lost. Please note: In limited operating conditions, a warning buzzer may also sound. A new brake reservoir assembly has been designed to prevent this condition from occurring.
T-SB-003-01 - OB
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE: July 7, 2014: This bulletin is now obsolete.
T-SB-0040-14
Service Bulletin/Repair Instructions
TSB: Some 2007 ? 2011 model year Camry HV vehicles may exhibit a MIL ?ON? and brake warning lights (ABS/VSC) illuminated in the instrument panel with Diagnostic Trouble Code (DTC) C1247 (Stroke Sensor Malfunction) stored in the ABS/VSC Electronic Control Unit (ECU). This DTC may set as a result of an overly sensitive monitoring logic without any other ABS/VSC system issue. Follow the Repair Procedure in this bulletin to properly diagnose the system and, if necessary, replace the ABS/VSC ECU with an ECU containing the updated monitoring logic.
T-SB-0041-14
Service Bulletin/Repair Instructions
TSB: Some 2007 ? 2011 model year Camry HV vehicles may exhibit a condition where the brake, ABS, and/or TRAC warning light(s) are ON and/or a Check VSC message is displayed. Diagnostic Trouble Code (DTC) C1391, C1252, C1253 or C1256 may be stored. This condition may be caused by a small internal brake fluid leak inside the brake actuator. Follow the Repair Procedure in this bulletin to address this condition.
TSB-0041-14 REV
Service Bulletin/Repair Instructions
TOYOTA: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. DUE TO SMALL INTERNAL BRAKE FLUID LEAKAGE, IN BRAKE ACTUATOR, THE ABS AND/OR TRAC WARNING LIGHT, FOR BRAKES, ARE ON AND CHECK VSC IS DISPLAYING A MESSAGE. MODEL 2007-2011 CAMRY. *LJ
ZE1_WEP_Dealer L
Service Bulletin/Repair Instructions
Dealer Letter: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for repairs related to internal malfunctions of the Brake Actuator assembly or overly sensitive monitoring logic for the Brake Pedal Stroke Sensor on 2007-2011 MY Camry Hybrid Vehicles. In these vehicles, Toyota has received some reports where various brake system related warning lamps illuminate due to internal malfunctions of the Brake Actuator assembly. Separately, the same warning lamps may also illuminate due to overly sensitive monitoring logic for the Brake Pedal Stroke Sensor. Although the Brake Actuator assembly and Skid Control ECU are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about the customers? ownership experience. Toyota is now extending the warranty coverage for repairs related to internal malfunctions of the Brake Actuator assembly or overly sensitive monitoring logic for the Brake Pedal Stroke Sensor. Please see the Warranty Enhancement Program Details for additional information.
ZE1_WEP_Region L
Service Bulletin/Repair Instructions
Region Letter: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for repairs related to internal malfunctions of the Brake Actuator assembly or overly sensitive monitoring logic for the Brake Pedal Stroke Sensor on 2007-2011 MY Camry Hybrid Vehicles. In these vehicles, Toyota has received some reports where various brake system related warning lamps illuminate due to internal malfunctions of the Brake Actuator assembly. Separately, the same warning lamps may also illuminate due to overly sensitive monitoring logic for the Brake Pedal Stroke Sensor. Although the Brake Actuator assembly and Skid Control ECU are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about the customers? ownership experience. Toyota is now extending the warranty coverage for repairs related to internal malfunctions of the Brake Actuator assembly or overly sensitive monitoring logic for the Brake Pedal Stroke Sensor. Please see the Warranty Enhancement Program Details for additional information.
T-TT-0292-14
Service Bulletin/Repair Instructions
Tech Tip: Some 2010-2011 model year Camry vehicles equipped with a U760E transaxle may exhibit a wine noise most noticeable between 40-60 mph.
T-TT-0010-10 Rev
Service Bulletin/Repair Instructions
Tech Tip: Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position Sensor Circuit) and/or P0340 (Camshaft Position Sensor Circuit) due to inconsistent rotational speed of the engine's crankshaft.
T-SB-0033-14
Service Bulletin/Repair Instructions
Some vehicles in particular geographic areas may exhibit a condition where the HVAC Evaporator Drain Hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
T-SB-0032-14
Service Bulletin/Repair Instructions
Some Avalon, Avalon HV, Camry, and Camry HV vehicles may exhibit an abnormal noise when turning and/or driving over uneven road surfaces. A new improved service part insulator for the front strut is available to reduce the possibility of the dust boot becoming wedged between the strut shaft bumper and strut shaft.; Follow the procedures in this bulletin to address this condition
T-TT-0223-13
Service Bulletin/Repair Instructions
The vehicle will not start or ready0on and the steering wheel lock is engaged so that the steering wheel may only be turned very little from side-to-side. If the operator attempts to ready-on or start the vehicle while there is tension on the steering lock actuator, it will not be able to fully disengage when the "ENGINE START STOP" or "POWER" switch is depressed. This condition will cause the "ENGINE START STOP" or "POWER" switch's LED to flash green and the vehicle will fail to ready-on or start.
T-TT-0288-14
Service Bulletin/Repair Instructions
Prior to installing remanufactured U660 and U760 transaxles, it is necessary to remove the lower oil cooler tube union from the original transaxle case and install it into the reman unit. A NEW O-ring and printed installation instructions are supplied in separate bag with the reman unit. An instruction tag is also affixed to the unit.
T-TT-0268-13
Service Bulletin/Repair Instructions
Customer complains of Bluetooth connectivity concerns such as: Difficulty to pair phone, Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.
T-SB-0012-14
Service Bulletin/Repair Instructions
Some 2007 ? 2011 model year Camry HV vehicles may exhibit a MIL ?ON? condition with Diagnostic Trouble Code (DTC) P0A80 or P0A7F stored due to dust or debris build-up in the HV Battery Cooling Fan. Use the following repair procedure to address this condition.
T-TT-0132-11
Service Bulletin/Repair Instructions
A key part to maintain the proper function and safe operation of the vehicle's braking system is to perform a visual inspection when installing brake pads, calipers, and discs. The following recommendations are intended to provide general tips for the inspection and/or installation of Toyota Complete Maintenance Care (TCMC) front brake pads and discs. Always refer to the model specific Repair manual and TIS publications for specific repair instructions.
T-TT-0262-13
Service Bulletin/Repair Instructions
Starting with the 2010 Model Year, Toyota began a gradual transition to the use of synthetic 0w-20 viscosity engine oil. There are multiple benefits of this oil. Due to the improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicle that require this oil.
T-SB-0187-12 Rev
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.
T-TT-0213-13
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with Supplemental Restraint Systems (SRS), including various airbags and in some models, seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pre-tensioner devices did not perform as expected (including an unintended deployment event), please follow the steps in the recommendations section below.
T-SB-0185-13
Service Bulletin/Repair Instructions
The following procedures are recommended during routine maintenance or in the event of a customer concern for wiper performance.
TS-BO030-01 Obso
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0185-13.
T-SB-0182-13
Service Bulletin/Repair Instructions
For vehicles that are used under certain severe operating conditions, the HV Battery Cooling Fan may exhibit an excessive buildup of dust, lint, or other debris that can reduce the efficiency of the HV Battery Cooling System. HV Battery Cooling Fan maintenance and cleaning should be performed to address this condition.
TSB-0182-13
Service Bulletin/Repair Instructions
TOYOTA: THE HV BATTERY COOLING FAN, UNDER SEVERE OPERATING CONDITIONS, AN EXCESSIVE BUILD UP OF LINT, DUST OR OTHER DEBRIS CAN REDUCE ITS EFFICIENCY AND CLEANING AND MAINTENANCE SHOULD BE PERFORMED TO CORRECT THIS CONDITION. MODEL 2007-2011 CAMRY HV. *PE
T-SB-0122-11 Rev
Service Bulletin/Repair Instructions
Beginning in 1998, Toyota introduced side airbags as optional equipment. Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT recommended by Toyota may affect side airbag performance, in general or in part, during an accident. Modifications that negatively affect side airbag performance can result in severe occupant injuries. Seat covers are an integral part of this safety system. Replacing fabric seat covers with non-Toyota leather or other seat cover materials may compromise the effectiveness of this safety system. The design of the seat is complex, integrating safety and strength with comfort and luxury. Toyota strongly discourages modifying original equipment seats that have optional side airbags. Additionally, Toyota strongly advises against the installation or use of aftermarket seat covers, which could impair the performance of the side airbags in the event of an accident.
T-SB-0041-13 Rev
Service Bulletin/Repair Instructions
Immediately following a cold soak startup, some 2009 ? 2013 model year vehicles equipped with 1AR-FE or 2AR-FE engines may exhibit a brief knock/rattle noise from the engine compartment for approximately one second. Follow the repair procedure below to address this condition.
T-TT-0269-13
Service Bulletin/Repair Instructions
The appearance of spots in tempered glass (when viewed at certain angles) is the result of the heat treating and quick quenching process during manufacturing.
T-TT-0051-10
Service Bulletin/Repair Instructions
If a customer states there is an unpleasant odor in the vehicle from the HVAC system, there are various factors that may be involved.
T-SB-0071-11 Rev
Service Bulletin/Repair Instructions
The purpose of this service bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL ?ON,? shifting issues, and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly
T-TT-0051-10 Rev
Service Bulletin/Repair Instructions
If a customer states there is an unpleasant odor in the vehicle from the HVAC system, there are various factors that may be involved.
T-TT-0250-13
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0250-13 Rev
Service Bulletin/Repair Instructions
To receive satellite radio functions after the initial trial period has expired, the customer must enter into a contract with XM Satellite Radio Inc. After entering into a contract, registration of an 8-digit XM Radio ID is required. This 8-digit XM Radio ID is found by turning to channel ?0? of the satellite radio.
T-SB-0142-13
Service Bulletin/Repair Instructions
Some 2004 ? 2014 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.
T-SB-0141-13
Service Bulletin/Repair Instructions
A new Special Service Tool (SST 09709-00002) has been introduced to aid in the inspection procedure for certain vehicles equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the Brake Pedal Force Gauge. Refer to the appropriate Repair Manual for parking brake pedal travel inspection and adjustment specification.
T-TT-0005-10
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0246-13
Service Bulletin/Repair Instructions
Tips for writing a DPR (Dealer Product Report) on manufacturing issues for windows and windshields.
T-SB-0086-13
Service Bulletin/Repair Instructions
Some 2009 ? 2011 model year North American production (NAP) vehicles equipped with BOSCH® made ABS/VSC systems may exhibit a repeated ABS and TRAC Warning Light ?ON? with Diagnostic Trouble Code (DTC) C1231 present. The ABS ECU logic has been modified to address this condition.
TSB-0086-13
Service Bulletin/Repair Instructions
TOYOTA: ON SOME VEHICLES, EXHIBITING THE WARNING LIGHT ON, DUE TO REPEATED ABS AND TRAC, WITH DIAGNOSTIC TROUBLE CODE (DTC) C1231 PRESENT AND TO ADDRESS CONDITION THE ABS ECU LOGIC WAS MODIFIED. MODEL 2009-2011 CAMRY. *PE
T-SB-0083-13
Service Bulletin/Repair Instructions
The procedure in this bulletin is a general guideline on how to properly diagnose the air conditioning system after a component failure. Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.
T-TT-0124-11
Service Bulletin/Repair Instructions
Please refer to the following recommendations for the best practices for vehicle tire rotations.
T-SB-0055-13
Service Bulletin/Repair Instructions
The purpose of this bulletin is to provide a procedure to repair the sun visor mount after improper installation/removal or if the sun visors are operated forcefully resulting in the sheet metal at the mounting area being damaged. If this has occurred, the sun visor base located on the headliner may become loose. To address this, a newly designed mounting bracket has been developed to address this condition. Use the following repair procedures to install the new mounting brackets.
T-SB-0284-09 Rev
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0055-13 .
T-PG006-00 Obsol
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0054-13.
T-SB-0054-13
Service Bulletin/Repair Instructions
California (CA), Federal (FED), and 50 State Certified emission control underhood labels (emission labels) may be obtained through your dealership?s Parts Department utilizing standard replacement parts ordering procedures. Follow the guidelines outlined in this bulletin to ensure proper label application.
T-TT-0118-11 Rev
Service Bulletin/Repair Instructions
Technicians should confirm the following key points to minimize the potential for future MIL "ON" concerns after HV battery replacement.
T-SB-0141-10 Rev
Service Bulletin/Repair Instructions
If a creak, tick, or rattle noise is heard at the top or bottom of the windshield, or at the top of the rear glass, the source of the noise may be the two stoppers bonded to the top of the windshield/rear glass, or the windshield retainers bonded to the lower edge of the windshield. This bulletin provides the recommended repair procedure to eliminate these types of noises from the windshield/rear glass area.
Renotification (
Service Bulletin/Repair Instructions
Toyota will be sending Safety Recall Follow Up Notices to remind owners whose vehicles have not yet had campaign repair completed. Please note the following information for Regional and PD associates.
T-SB-0045-13
Service Bulletin/Repair Instructions
Some 2010 ? 2011 model year Camry vehicles equipped with a 2AR-FE engine and automatic transmission may exhibit a MIL ?ON? condition with Diagnostic Trouble Code (DTC) P0128 (Coolant Temperature Below Thermostat Regulating Temperature). The Engine Control Module/ECM (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition occurring. Use the following repair procedure to address this condition.
T-SB-0041-13
Service Bulletin/Repair Instructions
Immediately following a cold soak startup, some 2009 ? 2013 model year vehicles equipped with 1AR-FE or 2AR-FE engines may exhibit a brief knock/rattle noise from the engine compartment for approximately one second. Follow the repair procedure below to address this condition.
T-SB-0146-10 Rev
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0041-13 .
TSB-004-13-A
Service Bulletin/Repair Instructions
TOYOTA: THERE IS A KNOCKING OR RATTLING NOISE COMING FROM ENGINE COMPARTMENT, FOR A SHORT PERIOD OF TIME, AFTER A COLD SOAK STARTUP. MODEL 2010-2012 CAMRY, 2009-2013 HIGHLANDER, VENZA, 2009-2012 RAV4, 2011-2013 SIENNA. *PE
TSB-0041-13
Service Bulletin/Repair Instructions
TOYOTA: ON CERTAIN VEHICLES, A KNOCK OR RATTLE NOISE, COMING FROM ENGINE COMPARTMENT, IS HEARD DURING A COLD SOAK STARTUP, AND THE CONDITION LASTS APPROXIMATELY ONE SECOND. MODEL YEARS 2009-2012 CAMRY, HIGHLANDER, SIENNA, VENZA, RAV4. *PE
T-TT-0226-13
Service Bulletin/Repair Instructions
The customer is having difficulty changing the multi-display screen from Day Mode. If the multi-display screen is set to Day Mode when the headlights are on, the setting we be memorized when the engine is turned off.
T-SB-0391-08 Rev
Service Bulletin/Repair Instructions
This bulletin contains general vehicle pulling diagnosis and repair procedures along with specific information to help correct pulling complaints.
T-SB-0033-13
Service Bulletin/Repair Instructions
Some customers may inquire about the frequency and power output of the Smart Key/Smart Entry systems used on various models. The Smart Key/Smart Entry systems conform to all applicable FCC rules. This bulletin details the applicable specifications for these systems.
SST Requirements
Service Bulletin/Repair Instructions
SSTs are key elements to provide your customers with swift and accurate repairs resulting in superior customer satisfaction.
SET Airbag Senso
Service Bulletin/Repair Instructions
This communication pertains to a current safety recall being conducted by the Southeast Toyota Distributors LLC (SET). TMS is sending this communication for informational purposes in the event you are contacted by a customer covered by this recall.
T-SB-0012-13
Service Bulletin/Repair Instructions
Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the TIS and the CUW.
T-SB-0064-10 Rev
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0012-13.
T-TT-0005-10 Rev
Service Bulletin/Repair Instructions
Starting with the 2010 MY, Toyota began a gradual transition to the use of synthetic 0w-20 viscosity engine oil.
T-SB-0093-09 Rev
Service Bulletin/Repair Instructions
A revised procedure has been developed to ensure proper removal and installation of the sun visor. Please use the following procedure for removal and installation of the sun visor.
T-SB-0205-12
Service Bulletin/Repair Instructions
Some 2010 ? 2011 model year Camry vehicles equipped with the 2AR-FE engine and some 2009 ? 2013 model year Venza vehicles equipped with the 1AR-FE engine may exhibit one or more of the following conditions: A/C inoperative while the vehicle is stopped. Rising engine temperature while the vehicle is stopped.
T-SB-0192-12
Service Bulletin/Repair Instructions
Some 2006 ? 2012 model year vehicles equipped with the 2AZ engine may exhibit an intermittent MIL ?ON? condition with Diagnostic Trouble Code (DTC) P0335 (Crankshaft Position Sensor ?A? Circuit) stored. The intake camshaft gear assembly has been improved to help prevent this condition.
CSP ZTT
Service Bulletin/Repair Instructions
Warranty Enhancement for Sun Visor Assemblies and Sun Visor Brackets
T-SB-0187-12
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.
TC-12-018
Service Bulletin/Repair Instructions
TOYOTA: SEE DOCUMENT RESEARCH BUTTON FOR OWNER LETTER. IN SOME VEHICLES, THE SUN VISORS WOULD SLOWLY ROTATE DOWNWARD AND SOME TIMES WOULD BECOME DETACHED. MODELS 2007-11 CAMRY & CAMRY HYBRIDS. *PE
TSB-0087-12
Service Bulletin/Repair Instructions
TOYOTA: ACCELERATOR PEDAL SENSOR ASSEMBLY INFORMATION REGARDING THE INSPECTION, REMOVAL, AND INSTALLATION, IF LUBRICATION OR OIL, IS APPLIED. *PE
T-SB-0055-12
Service Bulletin/Repair Instructions
TOYOTA: CHARGING SYSTEM INOPERATIVE. SOME ENGINES MAY EXHIBIT INSUFFICIENT CHARGING PERFORMANCE FROM THE ALTERNATOR. AN UPDATED PULLEY ASSEMBLY IS AVAILABLE TO ADDRESS THIS CONDITION. *JS
TSB-0163-11
Service Bulletin/Repair Instructions
TOYOTA: A CONDITION MAY EXHIBIT IN SOME VEHICLES WHERE DUST OR POWDER IS VISIBLE FROM HVAC VENTS. A PROCEDURE FOR INSTALLATION, BLOWER MOTOR CLEANING, EVAPORATOR REMOVAL AND HVAC SYSTEM CLEANING HAS BEEN DESIGNED FOR THIS CONDITION. *PE
T-SB-0122-11
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-0122-11
Service Bulletin/Repair Instructions
TOYOTA: INFORMATION PROVIDED FOR REPLACING THE SEAT COVERS FOR VEHICLES EQUIPPED WITH SIDE AIRBAGS. *PE
TTT-0119-11
Service Bulletin/Repair Instructions
TOYOTA: CERTAIN VEHICLES HAVE INOPERATIVE COOLING FAN. *PE
T-SB-0071-11
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0012-11
Service Bulletin/Repair Instructions
TOYOTA: THE MALFUNCTION LIGHT IS ON AND THERE IS A RATTLE NOISE FROM THE ENGINE. *RM UPDATED 9/21/11. *PE
SB-0002-11
Service Bulletin/Repair Instructions
TOYOTA: THERE MAY BE A RATTLE NOISE COMING FROM UNDER THE VEHICLE WHILE DRIVING. THIS MAY BE CAUSED BY THE FUEL TANK CONTACTING THE EXHAUST PIPE. *RM
TSB-0146-10
Service Bulletin/Repair Instructions
TOYOTA: BRIEF ENGINE KNOCK/RATTLE NOISE COLD STARTUP. IMMEDIATELY FOLLOWING A COLD SOAK STARTUP, SOME MODEL VEHICLES EQUIPPED WITH THE 1AR-FE AND 2AR-FE ENGINES MAY EXHIBIT A BRIEF KNOCK/RATTLE NOISE FROM THE ENGINE COMPARTMENT FOR APPROXIMATELY ONE SECOND. *PE UPDATED 9/28/11. *PE
TSB-0111-10
Service Bulletin/Repair Instructions
TOYOTA: 2AZ-FE & 2AZ-FXE THROTTLE BODY. ENGINE CONTROL. PROVIDE UPDATED THROTTLE BODY PART NUMBER INFORMATION FOR CERTAIN VEHICLES. THE DRAIN PIPE HAS BEEN ELIMINATED ON THROTTLE BODY SERVICE PARTS. *PE
TSB-0086-10 REV1
Service Bulletin/Repair Instructions
TOYOTA: FLOOR MAT INSTALLATION DURING PDS. VEHICLES EQUIPPED WITH DRIVER'S SIDE FLOOR MAT RETAINING CLIPS TO SECURE THE FLOOR MAT IN CORRECT POSITION. *PE
TSB-0064-10
Service Bulletin/Repair Instructions
TOYOTA: TECHSTREAM ECU FLASH REPROGRAMMING PROCEDURE. FLASH REPROGRAMMING ALLOWS THE ECU SOFTWARE TO BE UPDATED WITHOUT REPLACING THE ECU. FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. MODEL YEARS FROM 2001-2011. *PE
TSB-0364-09
Service Bulletin/Repair Instructions
TOYOTA: METER, GAUGE, DISPLAY. SOME VEHICLES MAY EXHIBIT A MIL ON CONDITION WITH DIAGNOSTIC TROUBLE CODE (DTC) P1423, OR A FUEL CAP BINDING UPON INSTALLATION OR REMOVAL. *PE UPDATED 5/16/11. *PE
TSB-0141-08 REV2
Service Bulletin/Repair Instructions
TOYOTA: VEHICLES WOULD HAVE WATER LEAK CONDITION IN THE HEADLINER. THIS CAUSES THE FOOT WELL TO BE WET. IT MAY RESULT FROM MOON ROOF DRAIN HOSES ARE LOOSE OR DISCONNECTED FROM DRAIN PAN NIPPLE. *PE
T-PG007-01
Service Bulletin/Repair Instructions
Replacement vin plates.
T-PG002-91
Service Bulletin/Repair Instructions
Product general information.